Search NASA⌕ Search

SEARCH · Search NASA

Results for “wall features”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

On the Mechanical Behavior of LP-DED C103 Thin-Wall Structures

Laser Powder Directed Energy Deposition (LP-DED) can produce thin-wall features on the order of 1 mm. These features are essential for large structures operating in extreme environments such as regeneratively cooled nozzles and heat exchangers, which often make use of refractory metals. In this work, the mechanical behavior of LP-DED C103 was investigated via quasi-static tensile testing and low cycle fatigue (LCF) testing. The effects of vacuum stress relief (SR) and hot isostatic pressing (HIP) heat treatments were investigated for specimens in the vertical and horizontal build orientations during tensile testing. The AB and SR properties were lower than literature values for wrought and laser powder bed fusion (L-PBF) bulk components but higher than electron beam powder bed fusion (EB-PBF). The application of a HIP cycle improved strength by 7% and ductility by 27% past the initial as-built condition. Fracture images reveal that interlayer stress concentration sites are responsible for fracture in specimens in the vertical orientation. Meanwhile, fracture in the horizontal specimens mainly propagates at a slanted angle typical of plane stress conditions. The LCF results show cycles to failure ranging from 100 cycles to 8000 cycles for max strain levels of 2% and 0.5%, respectively. Fractography on the fatigue specimens reveals an increasing propagation zone as max strain levels are increased. The impact of these findings and future work are discussed in detail.

36 MATERIALS SCIENCE↗

Additive Manufacturing Development and Hot-Fire Testing of Liquid Rocket Channel Wall Nozzles Using Blown Powder Directed Energy Deposition Inconel 625 and JBK-75 Alloys

Additive manufacturing (AM) is being investigated at NASA and across much of the rocket propulsion industry as an alternate fabrication technique to create complex geometries for liquid engine components that offers schedule and cost saving opportunities. The geometries that can be created using AM offer a significant advantage over traditional techniques. Internal complexities, such as internal coolant channels for combustion chambers and nozzles that would typically require several operations to manufacture traditionally can be fabricated in one process. Additionally, the coolant channels are closed out as a part of the AM build process, eliminating the complexities of a traditional process like brazing or plating. The primary additive manufacturing technique that has been evaluated is powder bed fusion (PBF), or selective laser melting (SLM), but there is a scale limitation for this technique. There are several alternate additive manufacturing techniques that are being investigated for large-scale nozzles and chambers including directed energy deposition (DED) processes. A significant advantage of the DED processes is the ability to adapt to a robotic or gantry CNC system with a localized purge or purge chamber, allowing unlimited build volume. This paper will discuss the development and hot-fire testing of channel-cooled nozzles fabricated utilizing one form of DED called blown powder deposition. This initial development work using blown powder DED is being explored to form the entire channel wall nozzle with integral coolant channels within a single AM build. Much of this development is focused on the design and DED-fabrication of complex and thin-walled features and on characterization of the materials properties produced with this techniques in order to evolve this process. Subscale nozzles were fabricated using this DED technique and hot-fire tested in Liquid Oxygen/Hydrogen (LOX/GH2) and LOX/Kerosene (LOX/RP-1) environments accumulating significant development time and cycles. The initial materials that were evaluated during this testing were high-strength nickel-based Inconel 625 and JBK-75. Further process development is being completed to increase the scale of this technology for large-scale nozzles. This paper will summarize the general design considerations for DED, specific channel-cooled nozzle design, manufacturing process development, property development, initial hot-fire testing and future developments to mature this technology for regeneratively-cooled nozzles. An overview of future development at NASA will also be discussed.

Gradl, Paul R.↗

Hot gas path component having cast-in features for near wall cooling

A hot gas path component includes a substrate having an outer surface and an inner surface. The inner surface of the substrate defines at least one interior space. At least a portion of the outer surface of the substrate includes a recess formed therein. The recess includes a bottom surface and a groove extending at least partially along the bottom surface of the recess. A cover is disposed within the recess and covers at least a portion of the groove. The groove is configured to channel a cooling fluid therethrough to cool the cover.

42 ENGINEERING↗

Methods to recover the narrow Dicke sub-Doppler feature in evacuated wall-coated cells without restrictions on cell size

The hyperfine resonance observed in evacuated wall-coated cells with dimensions lambda/2 (lambda is the hyperfine resonance wavelength) consists of a narrow Dicke sub-Doppler linewidth feature, the spike, superimposed on a broad pedestal. The hydrogen maser provides a classic example of this lineshape. As cell size is increased, an effect unique to evacuated wall-coated cells occurs. Certain combinations of microwave field distribution and cell size result in a lineshape having a pedestal with a small spike feature or only the broad pedestal with no spike. Such conditions are not appropriate for atomic frequency standard applications. The cause of the evacuated wall-coated cell lineshape is reviewed and methods to recover the narrow spike feature without restrictions on cell size is discussed. One example is a cell with dimensions having equal volumes of exposure to opposite phases of the microwave magnetic field.

Robinson, H. G.↗

Domain wall motion across microstructural features in polycrystalline ferroelectric films

This paper describes the effect of microstructural features such as grain boundaries and triple points on the pinning of domain wall motion in perovskite Pb(Zr 0.52 Ti 0.48 )O 3 (PZT) films on polycrystalline SrRuO 3 /SrTiO 3 substrates. Here, spatial variability in the collective domain wall dynamics was assessed using non-linearity mapping via Band Excitation Piezoresponse Force Microscopy (BE-PFM). Collocating the non-linearity maps with triple point locations (as visualized by EBSD) allowed for exploration of the effects that local microstructure (e.g., grain boundary) have on domain wall motion. It was found that the extrinsic behavior varied with both the misorientation angle and the proximity to the grain boundary. The width of influence of individual grain boundaries on the motion of domain walls was a function of the character of the grain boundary; random grain boundaries exhibit deeper minima in α d /d 33,initial and larger widths of influence (up to 905 nm) compared to coincident site lattice (CSL) boundaries (up to 572 nm). Additionally, triple points containing larger numbers of random boundaries exhibited non-Rayleigh behavior to greater distances, suggesting that the triple point provides either a deep potential minimum or a region where domain wall motion is unfavorable.

36 MATERIALS SCIENCE↗

Liquid Wall Chambers

The key feature of liquid wall chambers is the use of a renewable liquid layer to protect chamber structures from target emissions. Two primary options have been proposed and studied: wetted wall chambers and thick liquid wall (TLW) chambers. With wetted wall designs, a thin layer of liquid shields the structural first wall from short ranged target emissions (x-rays, ions and debris) but not neutrons. Various schemes have been proposed to establish and renew the liquid layer between shots including flow-guiding porous fabrics (e.g., Osiris, HIBALL), porous rigid structures (Prometheus) and thin film flows (KOYO). The thin liquid layer can be the tritium breeding material (e.g., flibe, PbLi, or Li) or another liquid metal such as Pb. TLWs use liquid jets injected by stationary or oscillating nozzles to form a neutronically thick layer (typically with an effective thickness of {approx}50 cm) of liquid between the target and first structural wall. In addition to absorbing short ranged emissions, the thick liquid layer degrades the neutron flux and energy reaching the first wall, typically by {approx}10 x x, so that steel walls can survive for the life of the plant ({approx}30-60 yrs). The thick liquid serves as the primary coolant and tritium breeding material (most recent designs use flibe, but the earliest concepts used Li). In essence, the TLW places the fusion blanket inside the first wall instead of behind the first wall.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Hardware and operating features of the adaptive wall test section for the 0.3-meter transonic cryogenic tunnel

A 13- by 13-inch adaptive wall test section was installed in the Langley 0.3-Meter Transonic Cryogenic Tunnel circuit. This test section has four solid walls and is configured for two-dimensional airfoil testing. The top and bottom walls are flexible and movable, whereas the sidwalls are rigid and fixed. The test section has a turntable to support airfoil models, a survey mechanism to probe the model wake, and provisions for a sidewall boundary-layer-control system. Details of the adaptive wall test section, the tunnel circuit modifications, the supporting instrumentation, the monitoring and control hardware, and the wall adaptation strategy are discussed. Sample results of shakedown tests with the test section empty and with an airfoil installed are also included.

Mineck, Raymond E.↗

Wall crossing from Dirac zeromodes

We explore the physics of two-body decay of BPS states using semiclassical analysis to construct explicit solutions that illustrate the main features of wall crossing, for both ordinary and framed BPS states. In particular we recover the primitive wallcrossing formula from an asymptotic analysis of certain Dirac-type operators on monopole moduli spaces. Along the way we give an asymptotic metric for the moduli space of singular monopoles, analogous to the Gibbons-Manton and Lee-Weinberg-Yi metrics for the moduli space of smooth monopoles, and we find evidence for the existence of stable non-BPS boundstates. Our discussion applies to four-dimensional N=2 super-Yang-Mills theories with general gauge group and general ’t Hooft defects.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

R and DE Robotic Sensor Intern Team: Sensor Suite Mock Up Testing

Assess sensor suite performance: - Mounted on crawler typical to what would be used in tunnel; - In test bed simulating the tunnel environment. The SuperDroid fiber tethered LT-F crawler is a general-purpose surveillance robot that our team has refurbished as a testing platform for the sensor suite. This crawler was selected because its dimensions are similar to the actual crawler that will be deployed in the field. Crawler preparation included: - Communicating with vendor to resolve software and platform issues; - Configuring a laptop with the crawler control software; - Reconfiguration of communication protocol between computer and crawler; - Resolution of control board checksum errors; - Installation of a mounting fixture on the base; - In progress: addition of lighting needed for total darkness. A solution for hosting the selected sensors onto a single unit that could function standalone or be mounted on the crawler was needed. Sensor mount requirements included: - Host Lidar, panospheric cameras and IMU sensors; - Cable management for rotating Lidar; - House on-board crawler computer; - Method for affixing to crawler; - Robust and vibration proof. The Lidar sensor required a sturdy mount that ensured the axis of rotation be centered with the LiDAR's desired laser path and included a slender profile in order to not block the scanning FOV. The mounting plate holds two 180-degree cameras on either side and the servo on the center. The servo mount is located so the axis of rotation is in the center of the plate. The mount features a set of guides that hold the wires and ensure they wrap around the spool area properly. The sensor box design features thick walls for added strength, holes for mounting the sensor suite to the crawler, notches on the bottom for the different components and holes for cable routing and management. The sensor mounts were designed using CREO and printed in the R and DE Additive Manufacturing Lab. To test the performance of the sensor suite for our application it was desired to design and build a test bed simulating the H-Canyon tunnel environment. Requirements included: - Dimensions similar to the tunnel; - Wall surfaces simulating the eroded tunnel walls; - Complete darkness; - Even and uneven crawler path; - Ability to change the tunnel width to simulate erosion. The HCAEX tunnel changes in height and includes several bends ranging from approximately 30 to 80 degrees, for that reason a test bed capable of easily being changed was needed. The final design includes two sections that can be connected to provide a 16' tunnel or placed at an angle to create a tunnel bend. The test bed features caster wheels for easy movement and has a sliding inner wall that enables tunnel width to be controlled. In order to simulate the tunnel walls without adding a lot of weight to the test bed, sheets of faux stone are to be used on the inner walls. To create a completely dark tunnel, 100% black-out film will be draped over the tunnel structure. Carpet remnants in the lab will enable folds to be introduced in the floor to generate uneven surface data.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Mitigating Moisture with High-R Walls

Energy-efficient building enclosures are key to decreasing energy load demand and enabling advanced space-conditioning systems for high-performance homes. One efficient enclosure design solution is high-R walls, which feature increased insulation levels as an effective solution for reducing air leakage and permeance of material layers. To increase builder confidence and encourage greater market adoption of high-R walls, Home Innovation Research Labs sought to demonstrate the long-term moisture performance of several high-R wall configurations in cold climate zones. The team monitored 22 newly constructed, occupied homes located throughout climate zones 4–7, where a substantial vapor drive to the exterior is present during the winter.

buildings↗

Multidimensional Unstructured-Grid Liquid Rocket Engine Nozzle Performance and Heat Transfer Analysis

The objective of this study is to conduct a unified computational analysis for computing design parameters such as axial thrust, convective and radiative wall heat fluxes for regeneratively cooled liquid rocket engine nozzles, so as to develop a computational strategy for computing those parameters through parametric investigations. The computational methodology is based on a multidimensional, finite-volume, turbulent, chemically reacting, radiating, unstructured-grid, and pressure-based formulation, with grid refinement capabilities. Systematic parametric studies on effects of wall boundary conditions, combustion chemistry, radiation coupling, computational cell shape, and grid refinement were performed and assessed. Under the computational framework of this study, it is found that the computed axial thrust performance, flow features, and wall heat fluxes compared well with those of available data and calculations, using a strategy of structured-grid dominated mesh, finite-rate chemistry, and cooled wall boundary condition.

Wang, Ten-See↗

Specific features of the radial distributions of plasma parameters in the initial segment of a supersonic jet generated by a pulsed capillary discharge

Results are presented from spectroscopic studies of the initial segment of a supersonic plasma jet generated by a pulsed capillary discharge with an ablative carbon-containing polymer wall. Specific features of the spatial distributions of the electron density and intensities of spectral components caused, in particular, by the high electron temperature in the central zone, much exceeding the normal temperature, as well as by the high nonisobaricity of the initial segment of the supersonic jet, are revealed. Measurements of the radiative properties of the hot jet core (the intensity and profile of the H{sub α} and H{sub β} Balmer lines and the relative intensities of C II lines) with high temporal (1–50 μs) and spatial (30–50 μm) resolutions made it possible to determine general features of the pressure and temperature distributions near the central shock. The presence of molecular components exhibiting their emission properties at the periphery of the plasma jet allowed the authors to estimate the parameters of the plasma in the jet region where “detached” shock waves form.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interior morphology of fresh Martian craters - The effects of target characteristics

The interior morphology of 183 fresh Martian craters observed on Viking imagery was studied. Freshness was determined by rim sharpness and continuity according to the scheme used to classify lunar and Mercurian craters. Results indicate that central-peak and wall degradation features are more common than previously thought. Central peaks are observed in craters as small as 2 km in diameter and in nearly all fresh craters with diameters greater than 10 km. Scallops or terraces are found to occur in all craters with diameters greater than 20 km, and wall slumping seems common in craters from 5 to 10 km in diameter. The ratio of crater diameter to crater floor diameter is significantly larger than for lunar craters. Central peaks and pits are more frequent in craters formed in cratered terrain than in those formed on plains; wall failure occurs at smaller diameters in plains craters. It is suggested that these peculiarities of crater interior morphologies may be due to a subsurface volatile layer. The influence of target variations on the interior morphologies observed in fresh craters was studied. Preliminary results indicate well-defined effects due to target differences.

Wood, C. A.↗

Design and Testing of an Ultra-Light Weight Perching System for Sloped or Vertical Rough Surfaces on Mars

In this paper, we present the design, characterization, and functional demonstration of a perching system that enables a flying vehicle to land on rough sloped or vertical surfaces. Steep slopes are of particular scientific interest since they are often associated with geologically interesting features including sites of active modification (e.g. landslides/avalanches, slope streaks), exposed bedrock and/or ice, and as-yet unmodified young features (e.g. walls of fresh craters or polar pits that are actively expanding). However the steep nature of these sites makes access with traditional field robots difficult: ground vehicles are unable to traverse the steep terrain and aerial vehicles are limited by their flight time and an ability to operate near terrain. We propose to address these limitation by enabling the UAV to reliably perch on steep terrain to perform in situ measurements and collect samples. Perching also enables a solar powered UAV to traverse large terrain features such as the Valles Marineris that could not be covered in a single flight by repeatedly perching and recharging its batteries. The proposed perching system that is being developed consists of a microspine gripper, a compliant gripper to vehicle interface, and a flying vehicle equipped with an autonomy sensor suite. The system also includes perception and control algorithms that identify perching targets and execute the required perching maneuver. To date, the majority of the effort has focused on developing and characterizing the microspine gripper. The initial prototype weighs 100 g, is capable of securely grasping a range of natural surfaces, and successful grasps support loads of over 10 N. Refinement of the gripper, integrating and testing it on a UAV, measuring aerodynamic distrubances from wall effects, and developing the required perception and control algorithms is ongoing. This paper describes the overall architecture of our proposed system, the design of the gripper, and its performance during initial testing.

Backus, Spencer↗

Realizing one-dimensional quantum and high-frequency transport features in aligned single-walled carbon nanotube ropes

The superiority of the electronic transport properties of single-walled carbon nanotube (SWNT) ropes over SWNT mats is verified from low temperature and frequency-dependent transport. The overall change of resistance versus in nanotube mats shows that 3D variable range hopping is the dominant conduction mechanism within the 2–300 K range. The magneto-resistance (MR) is found to be predominantly negative with a parabolic nature, which can also be described by the hopping model. Although the positive upturn of the MR at low temperatures establishes the contribution from quantum interference, the inherent quantum transport in individual tubes is suppressed at elevated temperatures. Therefore, to minimize multi-channel effects from inter-tube interactions and other defects, two-terminal devices were fabricated from aligned SWNT (extracted from a mat) for low temperature transport as well as high-frequency measurements. In contrast to the mat, the aligned ropes exhibit step-like features in the differential conductance within the 80–300 K temperature range. The effects of plasmon propagation, unique to one dimension, were identified in electronic transport as a non-universal power-law dependence of the differential conductance on temperature and source-drain voltage. The complex impedance showed high power transmission capabilities up to 65 GHz as well as oscillations in the frequency range up to 30 GHz. The measurements suggest that aligned SWNT ropes have a realistic potential for high-speed device applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗