Results for “ACTUATOR” — Page 20

NASA NTRS2014

Simulation Tool for Dielectric Barrier Discharge Plasma Actuators

Traditional approaches for active flow separation control using dielectric barrier discharge (DBD) plasma actuators are limited to relatively low speed flows and atmospheric conditions. This results in low feasibility of the DBDs for aerospace applications. For active flow control at turbine blades, fixed wings, and rotary wings and on hypersonic vehicles, DBD plasma actuators must perform at a wide range of conditions, including rarified flows and combustion mixtures. An efficient, comprehensive, physically based DBD simulation tool can optimize DBD plasma actuators for different operation conditions. Researchers are developing a DBD plasma actuator simulation tool for a wide range of ambient gas pressures. The tool will treat DBD using either kinetic, fluid, or hybrid models, depending on the DBD operational condition.

Likhanskii, Alexander↗

NASA NTRS2015

Flow Separation Control on A Full-Scale Vertical Tail Model Using Sweeping Jet Actuators

This paper describes test results of a joint NASA/Boeing research effort to advance Active Flow Control (AFC) technology to enhance aerodynamic efficiency. A full-scale Boeing 757 vertical tail model equipped with sweeping jets AFC was tested at the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel at NASA Ames Research Center. The flow separation control optimization was performed at 100 knots, a maximum rudder deflection of 30deg, and sideslip angles of 0deg and -7.5deg. Greater than 20% increments in side force were achieved at the two sideslip angles with a 31-actuator AFC configuration. Flow physics and flow separation control associated with the AFC are presented in detail. AFC caused significant increases in suction pressure on the actuator side and associated side force enhancement. The momentum coefficient (C sub mu) is shown to be a useful parameter to use for scaling-up sweeping jet AFC from sub-scale tests to full-scale applications. Reducing the number of actuators at a constant total C(sub mu) of approximately 0.5% and tripling the actuator spacing did not significantly affect the flow separation control effectiveness.

Andino, Marlyn Y.↗

NASA NTRS2015

Tension Stiffened and Tendon Actuated Manipulator

A tension stiffened and tendon actuated manipulator is provided performing robotic-like movements when acquiring a payload. The manipulator design can be adapted for use in-space, lunar or other planetary installations as it is readily configurable for acquiring and precisely manipulating a payload in both a zero-g environment and in an environment with a gravity field. The manipulator includes a plurality of link arms, a hinge connecting adjacent link arms together to allow the adjacent link arms to rotate relative to each other and a cable actuation and tensioning system provided between adjacent link arms. The cable actuation and tensioning system includes a spreader arm and a plurality of driven and non-driven elements attached to the link arms and the spreader arm. At least one cable is routed around the driven and non-driven elements for actuating the hinge.

Doggett, William R.↗

NASA NTRS2014

Flow Separation Control Over a Ramp Using Sweeping Jet Actuators

Flow separation control on an adverse-pressure-gradient ramp model was investigated using various flow-control methods in the NASA Langley 15-Inch Wind Tunnel. The primary flow-control method studied used a sweeping jet actuator system to compare with more classic flow-control techniques such as micro-vortex generators, steady blowing, and steady- and unsteady-vortex generating jets. Surface pressure measurements and a new oilflow visualization technique were used to characterize the effects of these flow-control actuators. The sweeping jet actuators were run in three different modes to produce steady-straight, steady-angled, and unsteady-oscillating jets. It was observed that all of these flow-control methods are effective in controlling the separated flows on the ramp model. The steady-straight jet energizes the boundary layer by momentum addition and was found to be the least effective method for a fixed momentum coefficient. The steady-angled jets achieved better performance than the steady-straight jets because they generate streamwise vortices that energize the boundary layer by mixing high-momentum fluid with near wall low-momentum fluid. The unsteady-oscillating jets achieved the best performance by increasing the pressure recovery and reducing the downstream flow separation. Surface flow visualizations indicated that two out-of-phase counter-rotating vortices are generated per sweeping jet actuator, while one vortex is generated per vortex-generating jets. The extra vortex resulted in increased coverage, more pressure recovery, and reduced flow separation.

Koklu, Mehti↗

NASA NTRS2016

Ball Screw Actuator Including an Axial Soft Stop

An actuator includes an actuator housing, a ball screw, and an axial soft stop assembly. The ball screw extends through the actuator housing and has a first end and a second end. The ball screw is coupled to receive a drive force and is configured, upon receipt of the drive force, to selectively move in a retract direction and an extend direction. The axial soft stop assembly is disposed within the actuator housing. The axial soft stop assembly is configured to be selectively engaged by the ball screw and, upon being engaged thereby, to translate, with compliance, a predetermined distance in the extend direction, and to prevent further movement of the ball screw upon translating the predetermined distance.

Wingett, Paul T.↗

NASA NTRS2015

High-Contrast Coronagraph Performance in the Presence of DM Actuator Defects

Deformable Mirrors (DMs) are critical elements in high contrast coronagraphs, requiring precision and stability measured in picometers to enable detection of Earth-like exoplanets. Occasionally DM actuators or their associated cables or electronics fail, requiring a wavefront control algorithm to compensate for actuators that may be displaced from their neighbors by hundreds of nanometers. We have carried out experiments on our High-Contrast Imaging Testbed (HCIT) to study the impact of failed actuators in partial fulfillment of the Terrestrial Planet Finder Coronagraph optical model validation milestone. We show that the wavefront control algorithm adapts to several broken actuators and maintains dark-hole contrast in broadband light.

adaptive optics↗

NASA NTRS2015

Effect of DM Actuator Errors on the WFIRST/AFTA Coronagraph Contrast Performance

The WFIRST/AFTA 2.4 m space telescope currently under study includes a stellar coronagraph for the imaging and the spectral characterization of extrasolar planets. The coronagraph employs two sequential deformable mirrors (DMs) to compensate for phase and amplitude errors in creating dark holes. DMs are critical elements in high contrast coronagraphs, requiring precision and stability measured in picometers to enable detection of Earth-like exoplanets. Working with a low-order wavefront-sensor the DM that is conjugate to a pupil can also be used to correct low-order wavefront drift during a scientific observation. However, not all actuators in a DM have the same gain. When using such a DM in low-order wavefront sensing and control subsystem, the actuator gain errors introduce high-spatial frequency errors to the DM surface and thus worsen the contrast performance of the coronagraph. We have investigated the effects of actuator gain errors and the actuator command digitization errors on the contrast performance of the coronagraph through modeling and simulations, and will present our results in this paper.

adaptive optics↗

NASA NTRS2019

Hinge for Use in a Tension Stiffened and Tendon Actuated Manipulator

A tension stiffened and tendon actuated manipulator is provided performing robotic-like movements when acquiring a payload. The manipulator design can be adapted for use in-space, lunar or other planetary installations as it is readily configurable for acquiring and precisely manipulating a payload in both a zero-g environment and in an environment with a gravity field. The manipulator includes a plurality of link arms, a hinge connecting adjacent link arms together to allow the adjacent link arms to rotate relative to each other and a cable actuation and tensioning system provided between adjacent link arms. The cable actuation and tensioning system includes a spreader arm and a plurality of driven and non-driven elements attached to the link arms and the spreader arm. At least one cable is routed around the driven and non-driven elements for actuating the hinge.

Doggett, William R.↗

NASA NTRS1997

Electroactive Polymers (EAP) low Mass Muscle Actuators

Actuation devices are used for many space applications with an increasing need to reduce their size, mass, and power consumption as well as cut their cost. Existing transducing actuators, such as piezoceramics, induce limited displacement levels. Potentially, electroactive polymers (EAP) have the potential for low-mass, low-power, inexpensive miniature muscle actuators that are superior to the widely used actuators.

Electroactive↗

NASA NTRS2021

Mathematical Model Development and Experimental Verification of Electromagnetic Force Actuators for use in Space Applications

This technical memorandum shows the development of the mathematics needed to model several types of electromagnetic force actuators that may be of interest for use in space applications. The actuators described are capable of providing attractive, repulsive, and longitudinal forces between the actuator and a variety of metal surfaces. Potential applications for these propellant free actuators include spacecraft docking, in-space fabrication, robotic spacecraft inspection and servicing, deflection of metallic debris, and interaction with iron core asteroids (e.g., landing, repelling, and relocating).

Robert C. Youngquist↗

NASA NTRSDate not supplied

A Methodology for Actuating RCS Jets in a Continuous, Time-Accurate CFD Simulation

Computational fluid dynamics simulations of Mars entry vehicle reaction control systems have been used to gain a better understanding of the wide range of flow phenomena encountered during various phases of flight. One aspect of this is simulating the system during controlled flight. Current practices model the system in a continuously actuated state, but this methodology is unable to accurately model the dynamic behavior of the system during EDL. One method to improve this is to create a coupled CFD-RBD-Control simulation. The first step to this is establishing a method of accurately actuating an RCS jet during a time accurate CFD simulation. This paper presents a method to achieve this actuation. There are three phases to the methodology: establishing the off state, creating a ramping function that will initialize the jet flow, and establishing the on state. A test case of a jet in a supersonic crossflow is implemented to establish the success of the methodology in being able to actuate a jet in the midst of an ongoing CFD simulation. It shows significant improvement in boundary condition responsiveness for linear and exponential ramping functions in comparison to the step function. A preliminary demonstration of the methodology is presented for the MSL vehicle which shows significant advantages for the implementation of a linear ramping function over a step function.

Alexandra Hickey↗

NASA NTRSDate not supplied

A Methodology for Actuating RCS Jets in a Continuous, Time-Accurate CFD Simulation

Computational fluid dynamics simulations of Mars entry vehicle reaction control systems have been used to gain a better understanding of the wide range of flow phenomena encountered during various phases of flight. One aspect of this is simulating the system during controlled flight. Current practices model the system in a continuously actuated state, but this methodology is unable to accurately model the dynamic behavior of the system during EDL. One method to improve this is to create a coupled CFD-RBD-Control simulation. The first step to this is establishing a method of accurately actuating an RCS jet during a time accurate CFD simulation. This paper presents a method to achieve this actuation. There are three phases to the methodology: establishing the off state, creating a ramping function that will initialize the jet flow, and establishing the on state. A test case of a jet in a supersonic crossflow is implemented to establish the success of the methodology in being able to actuate a jet in the midst of an ongoing CFD simulation. It shows significant improvement in boundary condition responsiveness for linear and exponential ramping functions in comparison to the step function. A preliminary demonstration of the methodology is presented for the MSL vehicle which shows significant advantages for the implementation of a linear ramping function over a step function.

Alexandra Hickey↗

DOE OSTI2025

Advanced silicone materials for soft actuator applications

Soft actuators are at the forefront of the innovation tide in medicine, manufacturing, and aerospace because they are able to mimic the behavior of biological tissue and adapt to complex, unstructured environments. Of all the materials used, silicone-based elastomers have drawn enormous attention since they offer a superb combination of mechanical flexibility, biocompatibility, thermal stability, and long-term durability. In the past few years, there has also been a rapid pace of material evolution, additive manufacturing, and biointegration that has enhanced the performance and applications of silicone-based soft actuators. However, there is no focused and timely review compiling these advances. This review seeks to address that need by critically discussing recent advancements in advanced silicone materials, exploring new fabrication methodologies, and discussing emerging applications that range from wearable devices to implantable robotics. We also present suggestions for directions and the problems which must be addressed in order to further develop the performance and potential of silicone-based soft actuators, justifying the relevance and urgency of this effort.

biocompatibility↗

NASA NTRS1998

Robotic Arm Actuated by Electroactie Polymers

Actuators are used for many planetary and space applications. To meet the NASA goal to reduce the actuators size, mass, cost and power consumption, electroactie polymers (EAP) are being developed to induce large bending and longitudinal actuation strains.

Robotics electroactive polymers hand simulation ac↗

NASA NTRS1996

Computation of Static Shapes and Voltages for Micromachined Deformable Mirrors with Nonlinear Electostatic Actuators

In modeling micromachined deformable mirrors with electrostatic actuators whose gap spacings are of the same order of magnitude as that of the surface deformations, it is neccessary to use nonlinear models for the actuators. In this paper, we consider micromachined deformable mirrors modeled by a membrane or plate equation with nonlinear electrostatic actuator characteristics.

deformations optical systems adaptive optical syst↗

NASA NTRSDate not supplied

Detailed Design of a Magnetically-Geared Actuator for Use in Extremely Cold Lunar Environments

A magnetically-geared actuator is being developed for extremely cold space environments to avoid the wiring and significant efficiency penalty associated with heating grease-lubricated actuators as well as the stringent life and loading constraints imposed by dry film lubricated mechanical gears. This paper describes the detailed design of this actuator, including the impactful requirements, thermal analysis, bearing loads, electromagnetic analysis and the impact of tolerance stack up, and structural analysis.

space mechanisms↗

NASA NTRSDate not supplied

Detailed Design of a Magnetically-Geared Actuator for use in Extremely Cold Lunar Environments

A magnetically-geared actuator is being developed for extremely cold space environments to avoid the wiring and significant efficiency penalty associated with heating grease-lubricated actuators as well as the stringent life and loading constraints imposed by dry film lubricated mechanical gears. This paper describes the detailed design of this actuator, including the impactful requirements, thermal analysis, bearing loads, electromagnetic analysis and the impact of tolerance stack up, and structural analysis.

space mechanisms↗

NASA NTRSDate not supplied

Development and Manufacture of A Proof-of-Concept Magnetically-Geared Actuator for Use in Extremely Cold Lunar Environments

A magnetically-geared actuator is being developed for extremely cold space environments to avoid the wiring and significant efficiency penalty associated with heating grease-lubricated actuators as well as the stringent life and loading constraints imposed by dry film lubricated mechanical gears. This paper describes the lessons learned while designing, manufacturing, and assembling a proof-of-concept prototype similar to the preliminary design of the actuator.

lunar surface↗