Results for “AIR TEMPERATURE” — Page 20

NASA NTRS2012

Roles of Urban Tree Canopy and Buildings in Urban Heat Island Effects: Parameterization and Preliminary Results

Urban heat island (UHI) effects can strengthen heat waves and air pollution episodes. In this study, the dampening impact of urban trees on the UHI during an extreme heat wave in the Washington, D.C., and Baltimore, Maryland, metropolitan area is examined by incorporating trees, soil, and grass into the coupled Weather Research and Forecasting model and an urban canopy model (WRF-UCM). By parameterizing the effects of these natural surfaces alongside roadways and buildings, the modified WRF-UCM is used to investigate how urban trees, soil, and grass dampen the UHI. The modified model was run with 50% tree cover over urban roads and a 10% decrease in the width of urban streets to make space for soil and grass alongside the roads and buildings. Results show that, averaged over all urban areas, the added vegetation decreases surface air temperature in urban street canyons by 4.1 K and road-surface and building-wall temperatures by 15.4 and 8.9 K, respectively, as a result of tree shading and evapotranspiration. These temperature changes propagate downwind and alter the temperature gradient associated with the Chesapeake Bay breeze and, therefore, alter the strength of the bay breeze. The impact of building height on the UHI shows that decreasing commercial building heights by 8 m and residential building heights by 2.5 m results in up to 0.4-K higher daytime surface and near-surface air temperatures because of less building shading and up to 1.2-K lower nighttime temperatures because of less longwave radiative trapping in urban street canyons.

urban vegetation↗

NASA NTRSDate not supplied

Comparisons of CFD Simulations of Icing Wind Tunnel Clouds with Experiments Conducted at the NASA Propulsions Systems Laboratory

This paper evaluates simulation predictions against experimental test data of icing clouds that were produced during 2018 ice crystal icing physics tests conducted at the NASA Propulsion Systems Laboratory icing wind tunnel. Aero-thermal and cloud parameters are set and known upstream at the tunnel inlet and spray system, but change as the cloud and air thermodynamically interact as the flowing masses reach the tunnel test section. Utilizing the ANSYS Fluent Discrete Phase Model function, 3D computational fluid dynamics (CFD) simulations were performed, capturing the thermodynamic interactions between the test parameters, and providing predictions of the aero thermal and cloud conditions at the tunnel test section. Simulation predictions were compared with test data that were measured at the tunnel exit plane. Evaluations focused on the cloud concentration (total water content), humidity content, and air temperature. CFD simulation predictions showed areas of agreement and disagreement. Simulations showed that cloud concentration profiles at the test section are strongly related to the initial spray nozzle pattern used at the tunnel inlet. Experimental data suggest that greater dispersion of the cloud occurred as the simulated cloud predicted areas of high and low cloud concentration compared to test data profiles. Simulations, however, captured the magnitude and location of the change in humidity content and the change in air temperature due to the presence of the cloud reasonably well, when compared to test data. This result would suggest that while the ANSYS simulation did not fully predict the spreading of the cloud as measured during experiment, it did capture evaporation and the molecular movements of air and vapor relatively well.

CFD↗

NASA NTRSDate not supplied

Comparisons of CFD Simulations of Icing Wind Tunnel Clouds with Experiments Conducted at the NASA Propulsions Systems Laboratory

This paper evaluates simulation predictions against experimental test data of icing clouds that were produced during 2018 ice crystal icing physics tests conducted at the NASA Propulsion Systems Laboratory icing wind tunnel. Aero-thermal and cloud parameters are set and known upstream at the tunnel inlet and spray system, but change as the cloud and air thermodynamically interact as the flowing masses reach the tunnel test section. Utilizing the ANSYS Fluent Discrete Phase Model function, 3D computational fluid dynamics (CFD) simulations were performed, capturing the thermodynamic interactions between the test parameters, and providing predictions of the aero thermal and cloud conditions at the tunnel test section. Simulation predictions were compared with test data that were measured at the tunnel exit plane. Evaluations focused on the cloud concentration (total water content), humidity content, and air temperature. CFD simulation predictions showed areas of agreement and disagreement. Simulations showed that cloud concentration profiles at the test section are strongly related to the initial spray nozzle pattern used at the tunnel inlet. Experimental data suggest that greater dispersion of the cloud occurred as the simulated cloud predicted areas of high and low cloud concentration compared to test data profiles. Simulations, however, captured the magnitude and location of the change in humidity content and the change in air temperature due to the presence of the cloud reasonably well, when compared to test data. This result would suggest that while the ANSYS simulation did not fully predict the spreading of the cloud as measured during experiment, it did capture evaporation and the molecular movements of air and vapor relatively well.

CFD↗

NASA NTRS1973

Development of helicopter engine seals

An experimental evaluation of main shaft seals for helicopter gas turbine engines was conducted with shaft speeds to 213 m/s(700 ft/sec), air pressures to 148 N/sq cm (215 psia), and air temperatures to 645 K (675 F). Gas leakage test results indicate that conventional seals will not be satisfactory for high-pressure sealing because of excessive leakage. The self-acting face seal, however, had significantly lower leakage and operated with insignificant wear during a 150-hour endurance test at sliding speeds to 145 m/s (475 ft/sec), air pressures to 124 N/sq cm (180 psia), and air temperatures to 408 K (275 F). Wear measurements indicate that noncontact operation was achieved at shaft speeds of 43,000 rpm. Evaluation of the self-acting circumferential seal was inconclusive because of seal dimensional variations.

Lynwander, P.↗

NASA NTRS1974

Mainshaft seals for small gas turbine engines

An experimental evaluation of mainshaft seals for small gas turbine engines was conducted with shaft speeds to 213 m/sec, air pressures to 215 psia, and air temperatures to 412 K. A radial face seal incorporating self-acting geometry for lift augmentation was evaluated. In addition, three conventional carbon seal types (face, circumferential segmented, and rotating ring) were run for comparison. Test results indicated that the conventional seals used in this evaluation may not be satisfactory in future advanced engines because of excessive air leakage. On the other hand, the self-acting face seal was shown to have the potential capability of limiting leakages to one-half that of the conventional face seals and one-fifth that of conventional ring seals. A 150 hour endurance test of the self-action face seal was conducted at speeds to 145 m/sec, air pressures to 180 psia, and air temperatures to 408 K. The seal wear was not measurable.

Ludwig, L. P.↗

NASA NTRS1948

Icing and De-Icing of a Propeller with Internal Electric Blade Heaters

An investigation has been made in the NACA Cleveland icing research tunnel to determine the de-icing effectiveness of an experimental configuration of an Internal electric propeller-blade heater. Two atmospheric Icing conditions and two propeller operating conditions were Investigated, In experiments with unheated blades and with heat applied to the blades both continuously and cyclically. Data are presented to show the effect of propeller speed., ambient air temperature and liquid-water concentration, and the duration of the heat-on and cycle times on the power requirements and de-Icing performance of the blade heaters. The extent of ice-covered area on the blades for various icing ax4 operating conditions has been determined. The largest iced area was obtained at the higher ambient-air temperatures and at low propeller speed. The ohord.wise extent of Icing In practically every case was greater than that covered by blade heaters. Adequate de-icing in the heated area with continuous application of heat was obtained with the power available but a maximum power, input of 1250 watts per blade was insufficient for cyclic de-Icing for the range of conditions investigated. Blade-surface temperature rates of rise of 0.2 to 0.7 F per second were obtained and the minimum cooling period for cyclic de-icing was found to be approximately 2-1/2 times the heating period.

Lewis, James P.↗

NASA NTRS1978

Degree of vaporization using an airblast type injector for a premixed-prevaporized combustor

Vaporization data that could be useful in designing premixed-prevaporized fuel preparation systems for gas turbine combustors are presented. The effect of the experimental parameters on vaporization was found to be E = T sub in tau 0.18 (V sub ref + 38) (P sub in + 35)/203000 where E is the degree of vaporization in percent, T sub in the inlet air temperature in K over the range 450 to 700 K, the residence time in ms over the range 4.3 to 23.8 ms, V sub ref the reference velocity in m/s over the range 5 to 22 m/s, and P sub in the inlet pressure in MPa over the range 0.18 to 0.59 MPa. Jet A and Diesel no. 2 fuels were tested for the effect of inlet air temperature and were found to have nearly identical results.

Tacina, R. R.↗

NASA NTRS1976

Performance and emission characteristics of swirl-can combustors to near-stoichiometric fuel-air ratio

Emissions and performance characteristics were determined for two full annular swirl-can combustors operated to near stoichiometric fuel-air ratio. Test condition variations were as follows: combustor inlet-air temperatures, 589, 756, 839, and 894 K; reference velocities, 24 to 37 meters per second; inlet pressure, 62 newtons per square centimeter; and fuel-air ratios, 0.015 to 0.065. The combustor average exit temperature and combustor efficiency were calculated from the combustor exhaust gas composition. For fuel-air ratios greater than 0.04, the combustion efficiency decreased with increasing fuel-air ratios in a near-linear manner. Increasing the combustor inlet air temperature tended to offset this decrease. Maximum oxides of nitrogen emission indices occurred at intermediate fuel-air ratios and were dependent on combustor design. Carbon monoxide levels were extremely high and were the primary cause of poor combustion efficiency at the higher fuel-air ratios. Unburned hydrocarbons were low for all test conditions. For high fuel-air ratios SAE smoke numbers greater than 25 were produced, except at the highest inlet-air temperatures.

Diehl, L. A.↗

NASA NTRS1978

Stratospheric composition balloon, aircraft and rocket-borne experiments, 28-30 September 1977 (systems, instruments, trajectories, supporting measurements)

The STRATCOM (STRATospheric COMposition) is a long term multipurpose program for integrated, correlated measurements of stratospheric parameters related to composition, thermodynamics, and radiative balance. Balloon 8-b, carrying a solar-pointing grating infrared spectrometer, two CO2 thermal emission radiometers and two in-situ air temperature sensors was launched at 1251 MST on 28 September 1977 to float at an altitude of 39 km from 1521 MST with the instruments making measurements at that altitude through the time of sunset at 1822 MST. Balloon 8-a lifted a payload consisting of four UV filter photometers, two UV spectrometers, two chemiluminescent ozonesondes, dasibi ozone monitor, 14 tube cryogenic sampler, two aluminum oxide H2O sensors, four air temperature sensors, atmospheric pressure sensor, infrared and visible pyranometers, downward-looking camera, blunt-kryton lamp-Gerdien condenser probe, three component anemometer, balloon apex-plate payload and three parachute-borne dropsondes.

Ballard, H. N.↗

NASA NTRS1986

Electron-nitrogen molecular collisions in high-temperature nonequilibrium air

Ab initio calculation of vibrational excitation and deexcitation cross sections of N2 by low energy resonant electron impact have been carried out. The calculation includes initial target state in v = 0-12 and final target state in v = 0-17. The calculated cross sections are found to agree with available experimental data to within reported experimental error. Effect of target rotation has been investigated. Comparison of vibrational excitation cross sections at J = 0, 50, and 150 shows that the major effect of target rotation is to lower the resonance energy. Vibrational excitation and deexcitation rate coefficients are tabulated for electron temperatures of 1100-55,000 K. The present tabulation supercedes an earlier compilation by the Naval Research Laboratory that was derived from experimental data with a factor-of-two error. The tabulated rate coefficients are suited for flowfield modeling of aeroassisted orbital transfer vehicles.

Huo, W. M.↗

NASA NTRS2018

Larch (Larix dahurica Turcz) growth response to climate change in the Siberian permafrost zone

Larch-dominant communities are the most extensive high-latitude forests in Eurasia and are experiencing the strongest impacts from warming temperatures. We analyzed larch (Larix dahurica Turcz) growth index (GI) response to climate change. The studied larch-dominant communities are located within the permafrost zone of Northern Siberia at the northern tree limit (ca. N 67° 38′, E 99° 07′). Methods included dendrochronology, analysis of climate variables, root zone moisture content, and satellitederived gross (GPP) and net (NPP) primary productivity. It was found that larch response to warming included a period of increased annual growth increment (GI) (from the 1970s to ca. 1995) with a follow on GI decline. Increase in GI correlated with summer air temperature, whereas an observed decrease in GI was caused by water stress (vapor pressure deficit and drought increase). Water stress impact on larch growth in permafrost was not observed before the onset of warming (ca. 1970). Water limitation was also indicated by GI dependence on soil moisture stored during the previous year. Water stress was especially pronounced for stands growing on rocky soils with low water-holding capacity. GPP of larch communities showed an increasing trend, whereas NPP stagnated. A similar pattern of GI response to climate warming has also been observed for Larix sibirica Ledeb, Pinus sibirica Du Tour, and Abies sibirica Ledeb in the forests of southern Siberia. Thus, warming in northern Siberia permafrost zone resulted in an initial increase in larch growth from the 1970s to the mid-1990s. After that time, larch growth increment has decreased. Since ca. 1990, water stress at the beginning of the vegetative period became, along with air temperature, a main factor affecting larch growth within the permafrost zone.

Larix dahurica↗

NASA NTRS1975

Gaseous exhaust emissions from a JT8D-109 turbofan engine at simulated cruise flight conditions

Gaseous emissions from a JT8D-109 turbofan engine were measured in an altitude facility at four simulated cruise flight conditions: Mach 0.8 at altitudes of 9.1, 10, 7, and 12.2 km and Mach 0.9 at 10.7 km. Engine inlet air temperature was held constant at 283 K for all tests. Emissions measurements were made at nominally 6 cm intervals across the horizontal diameter of the engine exhaust nozzle with a single-point traversing gas sample probe. Measured emissions of decreased with increasing altitude from an emission index of 10.4 to one of 8.3, while carbon monoxide increased with increasing altitude from an emission index of 1.6 to one of 4.4. Unburned hydrocarbon emissions were essentially negligible for all flight conditions. Since the engine inlet air temperatures were not correctly simulated, the NOx emission indices were corrected to true altitude conditions by using correlating parameters for changes in combustor inlet temperature, pressure, and temperature rise. The correction was small at the lowest altitude. At the 10.7 and 12.2 km, Mach 0.8 test conditions the correction decreased the measured values by 1 emission index.

Diehl, L. A.↗

NASA NTRSDate not supplied

Potential of a Plant Gas Exchange Mechanistic Model to Predict Plant Transpiration in Veggie on ISS

Plants are an essential part of long-duration space travel, as they enable food production and contribute to air revitalization through photosynthesis, and water recycling through transpiration. Understanding their growth mechanisms is essential to use them to sustain human life in space. In particular, gas exchange – e.g., CO2 absorption and water transpiration – are modified in microgravity because of the lack of buoyancy-driven convection, and in the long run, this could result in impaired plant growth. Water absorbed by the plants mainly depends on their size and on environmental conditions (air temperature, humidity and ventilation), but in microgravity watering plants is a delicate operation – too much water results in flooded roots and too little water leads in a few hours to wilted plants. This is regularly experienced in the Veggie system on ISS, which enables small-scale food production in microgravity since 2014. This presentation explores how a mechanistic model of plant gas exchange can help predict plant transpiration in Veggie and thus better predict daily watering. For each plant, inputs on canopy leaf area (acquired with daily photos), air temperature and relative humidity in the plant compartment, as well as airspeed at the top of its canopy enable accurate predictions of transpiration in microgravity. This brings a better understanding of water movement through the plant in microgravity in relation to ventilation and plant size and would result in easier management of plant watering in Veggie. Ultimately, this work could be applied to any space crop production in microgravity and be used for water management and yield predictions. This work was funded by NASA Space Biology through NASA postdoctoral program / USRA.

Lucie Poulet↗

NASA NTRSDate not supplied

Potential of a Plant Gas Exchange Mechanistic Model to Predict Plant Transpiration in Veggie on ISS

Plants are an essential part of long-duration space travel, as they enable food production and contribute to air revitalization through photosynthesis, and water recycling through transpiration. Understanding their growth mechanisms is essential to use them to sustain human life in space. In particular, gas exchange – e.g., CO2 absorption and water transpiration – are modified in microgravity because of the lack of buoyancy-driven convection, and in the long run, this could result in impaired plant growth. Water absorbed by the plants mainly depends on their size and on environmental conditions (air temperature, humidity and ventilation), but in microgravity watering plants is a delicate operation – too much water results in flooded roots and too little water leads in a few hours to wilted plants. This is regularly experienced in the Veggie system on ISS, which enables small-scale food production in microgravity since 2014. This presentation explores how a mechanistic model of plant gas exchange can help predict plant transpiration in Veggie and thus better predict daily watering. For each plant, inputs on canopy leaf area (acquired with daily photos), air temperature and relative humidity in the plant compartment, as well as airspeed at the top of its canopy enable accurate predictions of transpiration in microgravity. This brings a better understanding of water movement through the plant in microgravity in relation to ventilation and plant size and would result in easier management of plant watering in Veggie. Ultimately, this work could be applied to any space crop production in microgravity and be used for water management and yield predictions. This work was funded by NASA Space Biology through NASA postdoctoral program / USRA.

Lucie Poulet↗

NASA NTRS2020

Observational Constraints on the Effective Climate Sensitivity from the Historical Period

The observed warming in the atmosphere and ocean can be used to estimate the climate sensitivity linked to present-day feedbacks, which is referred to as the effective climate sensitivity (Shist). However, such an estimate is affected by uncertainty in the radiative forcing, particularly aerosols, over the historical period. Here, we make use of detection and attribution techniques to derive the surface air temperature and ocean warming that can be attributed directly to greenhouse gas increases. These serve as inputs to a simple energy budget to infer the likelihood of Shist in response to observed greenhouse gases increases over two time periods (1862–2012 and 1955–2012). The benefit of using greenhouse gas attributable quantities is that they are not subject to uncertainties in the aerosol forcing (other than uncertainty in the attribution to greenhouse gas versus aerosol forcing not captured by the multi-model aerosol response pattern). The resulting effective climate sensitivity estimate, Shist, ranges from 1.3 °Cto 3.1 °C(5%–95% range) over the full instrumental period (1862–2012) for our best estimate, and gets slightly wider when considering further uncertainties. This estimate increases to 1.7 °C–4.6 °C if using the shorter period (1955–2012).We also evaluate the climate model simulated surface air temperature and ocean heat content increase in response to greenhouse gas forcing over the same periods, and compare them with the observationally-constrained values.We find that that the ocean warming simulated in greenhouse gas only simulations in models considered here is consistent with that attributed to greenhouse gas increases from observations, while one model simulates more greenhouse gas-induced surface air warming than observed. However, other models with sensitivity outside our range show greenhouse gas warming that is consistent with that attributed in observations, emphasising that feedbacks during the historical period may differ from the feedbacks at CO2 doubling and from those at true equilibrium.

Tokarska, Katarzyna B↗

NASA NTRS2001

Southern Ocean Climate and Sea Ice Anomalies Associated with the Southern Oscillation

The anomalies in the climate and sea ice cover of the Southern Ocean and their relationships with the Southern Oscillation (SO) are investigated using a 17-year of data set from 1982 through 1998. We correlate the polar climate anomalies with the Southern Oscillation index (SOI) and examine the composites of these anomalies under the positive (SOI > 0), neutral (0 > SOI > -1), and negative (SOI < -1) phases of SOL The climate data set consists of sea-level pressure, wind, surface air temperature, and sea surface temperature fields, while the sea ice data set describes its extent, concentration, motion, and surface temperature. The analysis depicts, for the first time, the spatial variability in the relationship of the above variables and the SOL The strongest correlation between the SOI and the polar climate anomalies are found in the Bellingshausen, Amundsen and Ross sea sectors. The composite fields reveal anomalies that are organized in distinct large-scale spatial patterns with opposing polarities at the two extremes of SOI, and suggest oscillating climate anomalies that are closely linked to the SO. Within these sectors, positive (negative) phases of the SOI are generally associated with lower (higher) sea-level pressure, cooler (warmer) surface air temperature, and cooler (warmer) sea surface temperature in these sectors. Associations between these climate anomalies and the behavior of the Antarctic sea ice cover are clearly evident. Recent anomalies in the sea ice cover that are apparently associated with the SOI include: the record decrease in the sea ice extent in the Bellingshausen Sea from mid- 1988 through early 199 1; the relationship between Ross Sea SST and ENSO signal, and reduced sea ice concentration in the Ross Sea; and, the shortening of the ice season in the eastern Ross Sea, Amundsen Sea, far western Weddell Sea, and the lengthening of the ice season in the western Ross Sea, Bellingshausen Sea and central Weddell Sea gyre over the period 1988-1994. Four ENSO episodes over the last 17 years contributed to a negative mean in the SOI (-0.5). In each of these episodes, significant retreats in the Bellingshausen/Amundsen Sea were observed providing direct confirmation of the impact of SO on the Antarctic sea ice cover.

Kwok, R.↗

NASA NTRS2010

Relationship Between Satellite-Derived Snow Cover and Snowmelt-Runoff Timing and Stream Power in the Wind River Range, Wyoming

Earlier onset of springtime weather including earlier snowmelt has been documented in the western United States over at least the last 50 years. Because the majority (>70%) of the water supply in the western U.S. comes from snowmelt, analysis of the declining spring snowpack (and shrinking glaciers) has important implications for streamflow management. The amount of water in a snowpack influences stream discharge which can also influence erosion and sediment transport by changing stream power, or the rate at which a stream can do work such as move sediment and erode the stream bed. The focus of this work is the Wind River Range (WRR) in west-central Wyoming. Ten years of Moderate-Resolution Imaging Spectroradiometer (MODIS) snow-cover, cloud- gap-filled (CGF) map products and 30 years of discharge and meteorological station a are studied. Streamflow data from six streams in the WRR drainage basins show lower annual discharge and earlier snowmelt in the decade of the 2000s than in the previous three decades, though no trend of either lower streamflow or earlier snowmelt was observed using MODIS snow-cover maps within the decade of the 2000s. Results show a statistically-significant trend at the 95% confidence level (or higher) of increasing weekly maximum air temperature (for three out of the five meteorological stations studied) in the decade of the 1970s, and also for the 40-year study period. MODIS- derived snow cover (percent of basin covered) measured on 30 April explains over 89% of the variance in discharge for maximum monthly streamflow in the decade of the 2000s using Spearman rank correlation analysis. We also investigated stream power for Bull Lake Creek Above Bull Lake from 1970 to 2009; a statistically-significant trend toward reduced stream power was found (significant at the 90% confidence level). Observed changes in streamflow and stream power may be related to increasing weekly maximum air temperature measured during the 40-year study period. The strong relationship between percent of basin covered and streamflow indicates that MODIS data is useful for predicting streamflow, leading to improved reservoir management.

Hall, Dorothy K.↗

NASA NTRS2010

Relationship Between Satellite-Derived Snow Cover and Snowmelt-Runoff Timing and Stream Power in the Wind River Range, Wyoming

Earlier onset of springtime weather including earlier snowmelt has been documented in the western United States over at least the last 50 years. Because the majority (>70%) of the water supply in the western U.S. comes from snowmelt, analysis of the declining spring snowpack (and shrinking glaciers) has important implications for streamflow management. The amount of water in a snowpack influences stream discharge which can also influence erosion and sediment transport by changing stream power, or the rate at which a stream can do work such as move sediment and erode the stream bed. The focus of this work is the Wind River Range (WRR) in west-central Wyoming. Ten years of Moderate-Resolution Imaging Spectroradiometer (MODIS) snow-cover, cloud- gap-filled (CGF) map products and 30 years of discharge and meteorological station data are studied. Streamflow data from six streams in the WRR drainage basins show lower annual discharge and earlier snowmelt in the decade of the 2000s than in the previous three decades, though no trend of either lower streamflow or earlier snowmelt was observed using MODIS snow-cover maps within the decade of the 2000s. Results show a statistically-significant trend at the 95% confidence level (or higher) of increasing weekly maximum air temperature (for three out of the five meteorological stations studied) in the decade of the 1970s, and also for the 40-year study period. MODIS-derived snow cover (percent of basin covered) measured on 30 April explains over 89% of the variance in discharge for maximum monthly streamflow in the decade of the 2000s using Spearman rank correlation analysis. We also investigated stream power for Bull Lake Creek Above Bull Lake from 1970 to 2009; a statistically-significant end toward reduced stream power was found (significant at the 90% confidence level). Observed changes in streamflow and stream power may be related to increasing weekly maximum air temperature measured during the 40-year study period. The strong relationship between percent of basin covered and streamflow indicates that MODIS data is useful for predicting streamflow, leading to improved reservoir management

Hall, Dorothy K.↗