Search NASA⌕ Search

SEARCH · Search NASA

Results for “Advanced manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Pulsed electric current joining of oxide-dispersion-strengthened austenitic steels

The solid-state joining of oxide-dispersion-strengthened (ODS) austenitic steels was achieved using a pulsed electric current joining (PECJ) process. Microstructures of the austenitic grain structures and oxide dispersions in the joint areas were characterized using electron microscopy. Negligible grain growth was observed in austenitic grain structures, while slight coarsening of oxide dispersions occurred at a short holding time. The mechanisms of the PECJ process may involve three steps that occur simultaneously, including the sintering of mechanical alloying powders in the bonding layer, formation of oxide dispersions, and bonding of the mechanical alloying powders with the base alloy. The high hardness and irradiation resistance of ODS alloys were retained in the joint areas. This research revealed the fundamental mechanisms during the PECJ process, which is beneficial for its potential applications during the advanced manufacturing of ODS alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Temperature Dependent Early-Stage Oxidation Dynamics of Cu(100) Film with Faceted Holes

Fundamental understanding of surface oxidation dynamics is critical for rational corrosion protection and advanced manufacturing of nanostructured oxides. In situ environmental TEM (ETEM) provides high spatial (nano- to atomic- scale) and temporal (< 0.1 s) resolution to investigate the early-stage oxidation/corrosion dynamics of metals and alloys. Thin samples with facets are widely used to enable cross-sectional observation of the oxidation dynamics in ETEM. However, how different facet orientations oxidize under the same conditions, and how these facets change the oxidation process, has not been investigated before. Here, using in situ ETEM, we systematically compare the oxidation dynamics of Cu(001) thin films, with faceted holes exposing {100} and {110} facets at temperatures ranging from 250–600 °C under 0.03 Pa O 2 . Oxidation preference is observed to change, from Cu(110) facets at lower temperatures to Cu(100) facets at ~ 500 °C. Oxide growth mechanisms change from outward growth on Cu 2 O surfaces at low temperatures, to inward growth on Cu-Cu 2 O interfaces at high temperatures. At high temperatures (500–600 °C), a rod-like Cu 2 O morphology is observed, with side facets of ~ {024} and top facets of {100} on Cu(100). This differs from the square-shaped Cu 2 O exposing {110} facets formed on Cu(001) surfaces. Rod-like oxides exhibit directional growth along their lengths with linear growth rates, regardless of rod length and width. This suggests that O from Cu(001) surfaces, rather than Cu(100) facets, serves as an O source for oxide growth. These results show a direct comparison of oxidation at different orientations with temperature, underscoring the temperature dependence of oxidation preference. Our results also suggest future in situ ETEM experiments viewing oxidation corrosion cross-sectionally should be cautious when oxide size is comparable with sample thickness, as the oxidizing mechanism may change due to sample thickness.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Advancing Development and Application of Superalloys

This JOM topic is sponsored by the High Temperature Alloys Committee of TMS and addresses advances in the development and application of superalloys. Each year, the High Temperature Alloys Committee organizes symposia at the TMS and Materials Science and Technology annual meetings. In 2020, two symposia were organized for the TMS annual meeting on February 23–27 in San Diego, CA: Materials Design Approaches & Experiences V, co-sponsored by the Integrated Computational Materials Engineering Committee and Advancing Current and State-of-the-Art Applications of Ni- and Co-base Superalloys, co-sponsored by the Corrosion and Environmental Effects Committee. Later this year, the 14th International Symposium on Superalloys will be held on September 13-17 in Seven Springs, PA. The conference, held every 4 years, convenes members of the superalloy community to discuss recent challenges and discoveries affecting future performance and use of superalloys. The TMS High Temperature Alloys Committee meets at both the TMS Annual Meeting & Exhibition and the annual Materials Science and Technology conference. The meetings are open to anyone interested in high-temperature alloys. This special topic on Advancing Development and Application of Superalloys includes a range of sub-topics including mechanical performance, corrosion resistance, processing and advanced manufacturing techniques, which were submitted by research groups from industry, national laboratories and universities.

36 MATERIALS SCIENCE↗
DOE OSTI2025

DuctGPT: A Generative Transformer for Forward Screening of Ductile Refractory Multi-Principal Element Alloys

Designing ductile materials for extreme environments such as fusion reactors requires a deep understanding of the complex interplay between electronic structure, mechanical stability, and wide compositional space. Here, in this work, we introduce DuctGPT, a physics-informed, GPT-powered machine learning platform that enables rapid and accurate prediction of ductility across a wide range of refractory multi-principal element alloys (MPEAs). Trained on both experimental and high-fidelity computational data, DuctGPT integrates descriptors such as density of states at the Fermi level, elastic constants, and valence electron concentration to capture the fundamental mechanisms governing ductile versus brittle behavior. Using this framework, we screen over 1000 compositions in of body-centered cubic (BCC) MPEAs, including two new alloy classes, i.e., NbTa-rich (NbTa $>$ 50 at.%) NbTa-Ti-V and W-rich ($>$ 50 at.%) W-Ti-V MPEAs, to rapidly identify promising alloy compositions with enhanced ductility. Validation against experimental data confirms the model's ability to predict ductility with high fidelity and low uncertainty. By leveraging conversational AI and robust physical modeling, DuctGPT provides a blueprint for the next generation of alloy design assistants, enabling human-AI collaboration in the accelerated discovery of ductile, high-performance materials for fusion, aerospace, and advanced manufacturing.

AI/ML↗
DOE OSTI2024

High throughput automated characterization of enamel microstructure using synchrotron tomography and optical flow imaging

The remarkable damage-tolerance of enamel has been attributed to its hierarchical microstructure and the organized bands of decussated rods. A thorough characterization of the microscale rod evolution within the enamel is needed to elucidate this complex structure. While prior efforts in this area have made use of single particle tracking to track a single rod evolution to various degrees of success, such a process can be both computationally and labor intensive, limited to the evolution path of a single rod, and is therefore prone to error from potentially tracking outliers. Particle image velocimetry (PIV) is a well-established algorithm to derive field information from image sequences for processes that are time-dependent, such as fluid flows and structural deformation. In this work, we demonstrate the use of PIV in extracting the full-field microstructural distribution of rods within the enamel. Further, enamel samples from a wild African lion were analyzed using high-energy synchrotron X-ray micro-tomography. Results from the PIV analysis provide sufficient full-field information to reconstruct the growth of individual rods that can potentially enable rapid analysis of complex microstructures from high resolution synchrotron datasets. Such information can serve as a template for designing damage-tolerant bioinspired structures for advanced manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Accelerating laser ray tracing in high fidelity physics simulations of laser melting using squeeze U-net

Laser melting is a core component of the ongoing industrial revolution, dubbed Industry 4.0, as lasers facilitate fast and precise melting and fusion in advanced manufacturing. There is a strong need to optimize the laser process using simulations. However, this has proven challenging as high fidelity simulations are needed for predictive modeling and this is currently prohibitively expensive even when run on hundreds of processors on high performance computers. The challenge is capturing complex physics of laser material interaction, fluid dynamics, thermal physics and material phase transformations at various length and time scales. To close this technological gap, we modified a squeeze U-net to accelerate the laser ray tracing component of such high fidelity models by ~4x–40x while preserving the core physics principle of conservation of energy with 97% accuracy. This approach enables the accurate modeling of global laser energy absorption as a function of local surface temperatures and complex surface topologies, which govern the reflection directions and energy losses of laser rays upon interacting with the material surface.

Computer science↗
DOE OSTI2024

Predicting non-linear stress–strain response of mesostructured cellular materials using supervised autoencoder

Recent breakthroughs in advanced manufacturing capabilities have made it possible to design and print sophisticated topologies of cellular structures using diverse engineering materials such as metals, polymers, and ceramics. In these architectured materials, it is often desirable to tailor the mechanical properties by altering the unit cell topology. This necessitates an in-depth understanding of how the topology of the unit cell structure affects the macroscopic behavior of the material in both the linear and the non-linear regimes encountered under large compression. Here, we have developed a machine learning (ML) approach capable of accelerating the prediction of the stress–strain response of a polymer-based cellular structure under uniaxial confined compression. As part of generating the training data for ML, 60,000 mesostructures were generated using a relatively novel approach based on cellular automata, and their corresponding stress–strain responses were obtained from the finite element simulations. Principal component analysis (PCA) was used to reduce the dimensionality of the stress–strain curves. With only 20 principal components, PCA captured 99.89% of the variance in the stress–strain curves while reducing the dimensionality by 5X. ML using supervised autoencoder was able to successfully speed up the prediction of the non-linear stress–strain response of a unit cell by up to 4600X. The proposed method can serve as an efficient data generation tool and a rapid means for predicting the structure–property relationship through accelerated forward modeling of cellular materials under compaction, in cases where the macroscopic stress–strain response is governed by the unit-cell topology.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Innovative large overbraided carbon fiber composite beams in historical Friendship Bell Pavilion

The International Friendship Bell Pavilion located in the City of Oak Ridge, Tennessee symbolizes the spirit of the peace and friendship shared by the city of Oak Ridge and city of Naka, Japan. The Bell Pavilion features an 8000-pound bronze cast bell along with futuristic materials and advanced manufacturing technologies. The team has developed innovative overbraided carbon fiber arched beams in conjunction with the bronze bell. Carbon fiber was utilized in these beams because of its lightweight, strong, stiff, and durable characteristics. A sandwich design used a high-performance foam core, overbraided with triaxial carbon fibers. This is the world’s largest overbraided composite structure for parks and recreation. For the first time in such an application, 17 free floating, 33-foot (10 m) long arched carbon fiber composite beams cantilever from a central concrete-steel superstructure over the bronze bell. The arc radius of the bottom of each beam is uniquely different giving an appearance of an open dome when standing underneath the structure.

Parks and Recreation↗
DOE OSTI2021

Mathematical modeling of novel porous transport layer architectures for proton exchange membrane electrolysis cells

Thin foil based porous transport layers (PTLs) that contain highly structured pore arrays have shown promise as anode PTLs in proton exchange membrane electrolysis cells. These novel PTLs, fabricated with advanced manufacturing techniques, produce thin, tunable, multifunctional layers with reduced flow and interfacial resistances and high thermal and electric conductivities. To further optimize their design, it is important to understand their fundamental impact on the transport of protons, electrons, and liquid/vapor mixtures in the electrode. In this work, we develop a two-dimensional multiphysics model to simulate the coupled electrochemistry and multiphase transport in an electrolysis cell operated with the novel PTL architecture. The results show that larger pores improve access of water to the anode catalyst layer, which is beneficial for both the oxygen evolution reaction and membrane hydration. Larger pore sizes also improve oxygen gas transport from the catalyst layer, because generated oxygen gas is forced to travel in-plane through the anode catalyst layer until it reaches a pore opening that is connected to a channel. The discussed results confirm that the proposed thin foil based PTLs are fundamentally different from conventional PTLs, such as felts or layered meshes. The model developed in this work also provides generalizable insight into fundamental PEMEC phenomena, such as the competition between liquid and gas phase transport, membrane hydration and water management, and nonuniform electrochemical reactions, which are processes relevant to all PEMEC designs.

25 ENERGY STORAGE↗
DOE OSTI2025

Development, validation, and verification of multi-pass thermo-mechanical welding simulations using the open-source MOOSE framework: NeT TG4 benchmark weldment

This study develops and validates a sequentially coupled thermo-mechanical welding simulation for the three-pass 316L stainless steel NeT TG4 benchmark weldment using the open-source Multiphysics Object-Oriented Simulation Environment (MOOSE) and the Nuclear Engineering Material model Library (NEML). A diffused ellipsoidal heat source was calibrated against thermocouple data and weld macrographs to accurately model the fusion zone geometry and transient thermal fields. Material hardening is represented using the Lemaitre-Chaboche mixed isotropic-kinematic hardening model, while four annealing models - no annealing, single-stage at 1050 °C and 1300 °C, and two-stage at 800 °C/1300 °C - were implemented to assess the impact of annealing models on the accuracy of the predicted welding-induced plasticity, distortions, and residual stresses. The predictions were validated against experimental measurements and benchmarked against results from commercial software, demonstrating that thermo-mechanical MOOSE welding simulations achieve comparable accuracy with enhanced computational efficiency. This work highlights the potential of using open-source finite element frameworks like MOOSE for advanced manufacturing simulations.

Ji, Wendy [Australian Nuclear Science and Technolo↗
DOE OSTI2026

Fabrication of thin-walled tubes from alloy 602 CA using shear assisted processing and extrusion

Thin-walled tube is usually produced seamlessly via an expensive multi-step process or via welding of thin sheets but at reduced performance. To overcome the current process and performance inefficiencies, advanced manufacturing methods need to be investigated. In this investigation, shear assisted processing and extrusion (ShAPE) was used to fabricate thin-walled Inconel 602 tube in a single-step. Tubes measuring 0.83 m length with a 12 mm outer diameter and 1 mm wall thickness were fabricated with an average surface roughness, Ra of 1.6 µm and Rz of 15 µm. Tensile testing of tubes in the as-fabricated condition showed strength increases of 4-35% over current offerings while maintaining or improving elongation. Electron microscopy analysis revealed the recrystallized microstructure with refined inter- and intra-granular carbides. Preliminary results obtained in this investigation shows the feasibility of producing thin-wall high temperature tube in single-step via ShAPE. This achievement marks a significant step towards manufacturing larger diameter nickel alloy tubes for the U.S. Department of Energy’s Waste Treatment and Immobilization Plant.

36 MATERIALS SCIENCE↗
DOE OSTI2025

MOOSE ProbML: Parallelized probabilistic machine learning and uncertainty quantification for computational energy applications

Here, this paper presents the development and demonstration of massively parallel probabilistic machine learning (ML) and uncertainty quantification (UQ) capabilities within the Multiphysics Object-Oriented Simulation Environment (MOOSE), an open-source computational platform for parallel finite element and finite volume analyses. In addressing the computational expense and uncertainties inherent in complex multiphysics simulations, this paper integrates Gaussian process (GP) variants, active learning, Bayesian inverse UQ, adaptive forward UQ, Bayesian optimization, evolutionary optimization, and Markov chain Monte Carlo (MCMC) within MOOSE. It also elaborates on the interaction among key MOOSE systems — Sampler, MultiApp, Reporter, and Surrogate — in enabling these capabilities. The modularity offered by these systems enables development of a multitude of probabilistic ML and UQ algorithms in MOOSE. Example code demonstrations include parallel active learning and parallel Bayesian inference via active learning. The impact of these developments is illustrated through five applications relevant to computational energy applications: UQ of nuclear fuel fission product release, using parallel active learning Bayesian inference; very rare events analysis in nuclear microreactors using active learning; advanced manufacturing process modeling using multi-output GPs (MOGPs) and dimensionality reduction; fluid flow using deep GPs (DGPs); and tritium transport model parameter optimization for fusion energy, using batch Bayesian optimization. These capabilities are part of the MOOSE framework.

97 - MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Long carbon fibers boost performance of dry processed Li-ion battery electrodes

Dry processing (DP) is an advanced manufacturing technique for lithium-ion battery (LIB) electrodes. Unlike conventional wet-process-based manufacturing that involves dissolving polyvinylidene fluoride (PVDF) binder in n-methyl-2-pyrrolidone (NMP) solvent for slurry-casting, DP involves fibrillation of polymer binders. This method offers environmental and cost benefits by eliminating the need for expensive and environmentally hazardous organic solvents. However, DP-produced electrode films often lack mechanical stability due to the absence of a current collector substrate during electrode material layer fabrication. This reduced mechanical instability results in difficulty during fabricating of thin electrodes (≈5 mAh/cm 2 ). To address this issue, long (>8 mm) carbon fiber (CF) has been incorporated to reinforce the mechanical strength of the electrode films. In conclusion, the study demonstrates that the inclusion of long carbon fiber boosts the mechanical, electrical, thermal, and electrochemical performance of DP electrodes.

25 ENERGY STORAGE↗
DOE OSTI2026

Creep in multi-principal element materials –– A review

The ongoing push towards enhanced energy efficiency and reduced emissions has necessitated the creation of materials with superior performance, especially under extreme conditions. Modern industries, such as aerospace, energy production, and nuclear power, rely heavily on materials that can withstand elevated temperatures without compromising structural integrity. At these heightened temperatures, materials, even when subjected to mechanical stresses well below their yield strength, may experience slow deformation leading to eventual rupture — a phenomenon known as creep. With the expansive design space that comes with the high entropy concept and their reported excellent high temperature strength, multi-principal element materials (MPEMs) have attracted interest in the scientific community for high-temperature applications. Here, this review offers a comprehensive examination of existing studies on creep in MPEMs, which includes multi-principal element−alloys, −bulk metallic glasses, −ceramics, and −superalloys, comparing published findings on MPEMs with pure elements, traditional alloys, bulk metallic glasses, and superalloys. The sub-topics covered include a comparison among different creep-testing methods, creep mechanisms, creep exponents, creep strain rates, activation volume, and creep-activation energy. Modeling efforts for predicting creep behavior of MPEMs are also reviewed. Methods for improving creep resistance by performing heat treatments and/or modifying microstructures are discussed. Overall, the current state of MPEMs has not yet surpassed the creep performance of commercial alloys. Finally, directions for future efforts are suggested, such as experimenting in various controlled environments, expanding the number of compositions tested, exploring advanced manufacturing techniques, and using machine-learning to predict creep properties based on compositions and microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Comparison of powder bed fusion and directed energy deposition for tailoring mechanical properties of traditionally brittle alloys

The mechanical performance of an Fe-Co intermetallic alloy processed by laser powder bed fusion (L-PBF) and laser directed energy deposition (L-DED) additive manufacturing is compared. L-PBF material was characterized by high strength (500–550 MPa) and high ductility (35%) in tension, corresponding to a ~250% increase in strength and an order-of-magnitude improvement in ductility relative to conventional material. Conversely, L-DED material exhibited similarly poor tensile properties to the conventional wrought alloy, with low strength (200–300 MPa) and low ductility (0–2.7%). Finally, the disparity in properties between L-PBF and L-DED material is discussed in the context of the fundamental differences between manufacturing methods.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Advanced neutron absorber Ni-Cr-Mo-Gd alloys seawater corrosion mechanism and susceptibility study

Previous studies demonstrated the corrosion susceptibility of advanced neutron absorber (ANA) Ni-Cr-Mo-Gd in a seawater environment but remained inconclusive. In this paper, scanning electron microscopy was employed to identify the corrosion phase in Ni-Cr-Mo-Gd, and computational thermodynamic simulation was used to study phase corrosion potentials. Results showed that the Ni 5 Gd second phase, distributed along FCC grain boundaries in Ni-Cr-Mo-Gd, has lower corrosion potential than the substrate. Furthermore, heat treatment and alloy chemistry adjustment would not ameliorate the ANA corrosion susceptibility. Finally, isolating the Ni 5 Gd from the corrosion medium through advanced manufacturing is a viable way to improve the ANA corrosion resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Porosity evolution during heating of copper made from powder by friction extrusion

Here, friction extrusion was used to compact and extrude solid copper rod from feedstock powders. Following extrusion, considerable porosity was observed throughout the extrudate cross section due to the entrained porosity in the feedstock material and the extrusion process. The thermal stability of the extrudate was investigated via a series of heat treatments. Porosity evolution exhibited three distinct stages—an unchanged plateau (0°C–300°C) followed by an abrupt increase (400°C–500°C) and ultimately a reduction, as the temperature increases (>500°C). The peak porosity measured was ~25%. The underlying driving force for pore evolution is described as the competition between the internal pore pressure, material strength, and sintering kinetics, as a function of temperature. The observed porosity evolution and driving force are not expected to be limited to copper. Thus, this manuscript reveals an important consideration regarding elevated-temperature thermal stability as advanced manufacturing methods involving direct powder extrusion are explored.

36 MATERIALS SCIENCE↗