SEARCH · Search NASA

Results for “Boundary layer structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

DOE OSTI2023

A Time-Gated, Time-Correlated Single-Photon-Counting Lidar to Observe Atmospheric Clouds at Submeter Resolution

Most lidars used for cloud observations have the range resolution of about 10 m, so they are incapable of resolving submeter-scale processes that are crucial to cloud evolution. This article describes a prototype of a ground-based, vertically pointing, time-gated, time-correlated single-photon-counting lidar (referred to as the T2 lidar) developed to explore atmospheric clouds at range resolution two orders of magnitude finer than traditional atmospheric lidars. The T2 lidar emits green-light pulses (532 nm) at a repetition rate of 20.6 kHz and a pulse width of ∼650 ps, which enables the observation of aerosol and cloud layers at heights from a few hundred meters to 7.28 km above the ground level at range resolution down to 10 cm. In addition, a digital delay pulse generator controls the detector to only receive photons for a short period after each laser pulse. This time-gated technique blocks photons arriving from regions outside the target zone, thus significantly reducing the noise level and allowing observation even inside clouds. Initial observations show that the T2 lidar can detect sharp cloud boundaries and fine structures near the cloud base. Such refined measurements of cloud structure could lead to an improved understanding of microphysical processes such as droplet activation, entrainment and mixing, and precipitation.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

The subsurface structure of abraded Al–Zn–Mg–Cu alloy

Surface abrasion has been shown to introduce heavy shear stress and produce a few hundred nanometers thick altered surface layer (ASL) on Al alloys. Such ASLs exhibit microstructural changes at room temperature and different corrosion resistance than the underlying substrate. Here, we report how sample dimensions and temperature affect the deformed subsurface microstructure evolution on an abraded Al–Zn–Mg–Cu alloy using transmission electron microscopy (TEM) and atom probe tomography. The ASL microstructure evolves differently in the bulk sample than in the thin TEM specimen. In the freshly abraded ASL, the original η'/η precipitates and grain boundaries were deformed toward the abrasion direction. After 7-day natural aging of the freshly abraded bulk sample, well-defined subgrains formed locally in the ASL, and unusual Al 2 Cu (θ) and Mg x Zn y phases precipitated at the subgrain boundaries. However, during natural aging of this TEM specimen taken from the abraded and aged bulk samples, much faster changes occurred, including the continued formation of subgrains and θ particles in the entire ASL, and the diffusion of Zn atoms out of Mg x Zn y particles to form a Zn particle. On the other hand, no obvious microstructural changes occurred in the ASL during 3-month natural aging of the TEM specimen immediately taken from the freshly abraded sample. Finally, this work advances the understanding of how Al alloy microstructures respond during and following any shear deformation, and complex and unexpected effects of sample dimensions on the behavior.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Novel architectures for stabilization of Mn-rich cathodes: a high-valent approach to interfaces

Lithium- and manganese-rich (LMR) layered oxides continue to generate significant interest as promising, earth-abundant cathode materials for next-generation Li-ion batteries. In spite of their attractive capacity and cost advantages, a few long-standing challenges still hamper their widespread adoption, with manganese dissolution being one of the most persistent and vexing issues. In the present study, we explore the incorporation of Sb5+ as a high-valent cation and exploit its ability to form unique lithium-rich surface and grain-boundary structures that can integrate directly with the LMR lattice. When synthesized under appropriate conditions, Sb5+ orders strongly with Li+ to form localized Li+–Sb5+ motifs, which play a key role in restructuring the surface and grain-boundary regions. These restructured regions act as protective, stabilizing entities that substantially suppress electrolyte-driven side reactions, reduce impedance growth, limit manganese dissolution, and help retain cyclable lithium during long-term electrochemical cycling. Further improvements of the electrochemical performance of Sb-treated LMR were achieved using a well-known additive to mitigate Mn dissolution and highlight the synergistic effects of combined strategies. Overall, this work showcases how high-valent elements such as Sb5+ can help tailor the surface and intergranular regions and work in synergy with other modifiers (e.g. electrolyte additives), enhancing the cycle life and practical viability of LMR cathodes for use in graphite-based full cells.

Mallick, Subhadip [Argonne National Laboratory (AN↗

DOE OSTI2022

Invertible Neural Networks for Airfoil Design

We report the airfoil design problem, in which an engineer seeks a shape with desired performance characteristics, is fundamental to aerodynamics. Design workflows traditionally rely on iterative optimization methods using low-fidelity integral boundary-layer methods as higher-fidelity adjoint-based computational fluid dynamics methods are computationally expensive. Surrogate-based approaches can accelerate the design process but still rely on some iterative inverse design procedure. In this work, we leverage emerging invertible neural network (INN) tools to enable the rapid inverse design of airfoil shapes for wind turbines. INNs are specialized deep-learning models with well-defined inverse mappings. When trained appropriately, INN surrogate models are capable of forward prediction of aerodynamic and structural quantities for a given airfoil shape as well as inverse recovery of airfoil shapes with specified aerodynamic and structural characteristics. The INN approach offers a roughly 100 times speed-up compared to adjoint-based methods for inverse design. We demonstrate the INN tool for inverse design on three test cases of 100 airfoils each that satisfy the performance characteristics close to those of airfoils used in wind-turbine blades. All generated shapes satisfy the desired aerodynamic characteristics, demonstrating the success of the INN approach for inverse design of airfoils.

17 WIND ENERGY↗

DOE OSTI2020

An Overview of Neutron Irradiated SiC Layer Behavior using Micro-and Nano-Characterization Techniques

The complexity of fission product distribution and composition within the SiC layer of tristructural isotropic (TRISO) coated particles, irradiation effects on the SiC structure as well as the variable nature of metallic fission product release, has led to the exploration of multiple micro- and nano-characterization techniques. The fine scale of the fission product precipitates necessitates unique learnings and application of electron microscopic techniques with irradiated fuel during the Advanced Gas Reactor (AGR)-1 experiment analysis. A summarized discussion on the specific advanced techniques with associated method development for TRISO coated particles is provided followed by the down selected techniques currently considered to provide the highest impact. Techniques considered are electron probe micro-analyzer (EPMA), scanning transmission electron microscopy (STEM), and Precession electron diffraction (PED). SiC grain boundary characteristics are evaluated due to the mobility of specific fission products through grain boundaries. PED was performed for understanding the role of grain boundary character on fission product transport. One set of comparative analyses between AGR-1 and AGR-2 particles leads to a finding that the AGR-1, high-Ag-retention particle, had statistically more coincidence site lattice (CSL)-related grain boundaries (but fewer low-angle grain boundaries), compared to the AGR-2 particle. This implies that CSL-related grain boundaries may have a direct influence on Ag retention. However, precipitates were found on a relatively small fraction of CSL-related grain boundaries in both particles. In another set of comparison between AGR-1 and AGR-2 particles that were subjected to safety testing, there is significant differences in average SiC grain boundary distributions, but the fission product distributions on these grain boundaries are very similar.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Micro- and Nano-techniques for the Study of Fission Product Precipitation in SiC Layer

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Unusual electrical conductivity driven by localized stoichiometry modification at vertical epitaxial interfaces

Precise control of lattice mismatch accommodation and interfacial cation diffusion is critical to modulate correlated functionalities in epitaxial heterostructures, particularly when the interface composition is positioned near a compositional phase transition boundary. Here we select La 1-x Sr x MnO 3 (LSMO) as a prototype phase transition oxide and establish vertical epitaxial interfaces with NiO for exploring the strong interplay between strain accommodation, stoichiometry modification, and localized electron transport across the interface. It is found that localized stoichiometry modification overcomes the dead layer problem plaguing LSMO and leads to strongly directional conductivity, as manifested by a more than three orders of magnitude difference between out-of-plane and in-plane conductivity. Comprehensive atomic scale structural characterization and transport measurements reveal that this emerging behavior is created by a compositional change produced by preferential cation diffusion that pushes the LSMO phase transition from insulating into metallic within an ultrathin interface region. This study explores the nature of unusual electrical conductivity at vertical epitaxial interfaces and highlights the beneficial role of controllable cation diffusion that enables emerging functionalities for a broad range of potential applications such as memristors, spintronic devices, and novel nanoelectronic devices using strongly correlated materials.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Thermodynamics of electrolyte solutions near charged surfaces: Constant surface charge vs constant surface potential

Electric double layers are ubiquitous in science and engineering and are of current interest, owing to their applications in the stabilization of colloidal suspensions and as supercapacitors. While the structure and properties of electric double layers in electrolyte solutions near a charged surface are well characterized, there are subtleties in calculating thermodynamic properties from the free energy of a system with charged surfaces. These subtleties arise from the difference in the free energy between systems with constant surface charge and constant surface potential. In this work, we present a systematic, pedagogical framework to properly account for the different specifications on charged bodies in electrolyte solutions. Our approach is fully variational—that is, all free energies, boundary conditions, relevant electrostatic equations, and thermodynamic quantities are systematically derived using variational principles of thermodynamics. We illustrate our approach by considering a simple electrolyte solution between two charged surfaces using the Poisson–Boltzmann theory. Our results highlight the importance of using the proper thermodynamic potential and provide a general framework for calculating thermodynamic properties of electrolyte solutions near charged surfaces. Specifically, we present the calculation of the pressure and the surface tension between two charged surfaces for different boundary conditions, including mixed boundary conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Design and Analysis of the Open-Surface Slow Li Flow Divertor and Comparison to the Fast Li Flow Divertor

In the ongoing U.S. project, “Liquid Metal Plasma Facing Components,” sponsored by the U.S. Department of Energy, efforts have been taken to develop two open-surface divertor designs for the Fusion Nuclear Science Facility using liquid lithium (Li) as a heat and particle flux removal media. The main focus of this study is the design and analysis of a slow (~1 mm/s) and thin (<1 mm) open-surface Li flow divertor with a Li-cooled substrate, which is then compared with an earlier design of a fast (up to 10 m/s) and thick (~0.5 cm) Li flow divertor with the substrate cooled with helium. The slow Li flow divertor design is based on the original LiWall concept developed at the Princeton Plasma Physics Laboratory. Such a thin and slow Li layer can remove the particle flux by reducing the recycling flux, while the heat flux is removed mainly through the heat sink located beneath. In the present study, the heat sink is provided through a Li cooling flow inside the substrate of reduced activation ferritic/martensitic steel. By performing a multiphysics analysis with COMSOL that included liquid-metal magnetohydrodynamics (MHD), heat transfer, and structural mechanics, the impact of various factors on the divertor heat removal capability, such as Li flow velocity, MHD effects, and inlet velocity boundary condition, were examined. Based on comparisons of the two divertor designs, it was shown that the fast-flow divertor significantly outperformed the slow-flow design, whose heat removal capability was limited to ~1 to 2 MW/m2.

Jiang, Yuchen [ORNL] (ORCID:0000000283280284)↗

DOE OSTI2020

Pervasive low-velocity layer atop the 410-km discontinuity beneath the northwest Pacific subduction zone: Implications for rheology and geodynamics

Regional triplication waveforms of five intermediate-depth events are modeled to simultaneously obtain the compressional (P) and shear (SH) wave velocity structure beneath northwestern Pacific subduction zone. Both the P- and SH-wave velocity models for three different sub-regions show a low-velocity layer (LVL) with a thickness of ~55-80 km lying above the 410-km discontinuity with a ~900 km lateral extent from the Japan Sea to the northeastern Asian continental margin. With the dihedral angle approaching to zero around 400 km, a minute amount of melt atop the 410-km discontinuity caused by the hydrous slab might completely wet olivine grain boundaries and result in a low seismic velocity layer in this specific subduction zone. This mechanism suggests that the 410-LVL is a low viscosity zone that would partially decouple the upper mantle from the transition zone. We infer that the widespread 410-LVL provides evidence for a water-bearing mantle transition zone beneath the western Pacific subduction zone.

58 GEOSCIENCES↗

DOE OSTI2025

Pyrochlore NaYbO2: A Potential Quantum Spin Liquid Candidate

The search for quantum spin liquids (QSL) and chemical doping in such materials to explore superconductivity have continuously attracted intense interest. Here, we report the discovery of a potential QSL candidate, pyrochlore-lattice β-NaYbO2. Colorless and transparent NaYbO2 single crystals, layered α-NaYbO2 (∼250 μm on edge) and octahedral β-NaYbO2 (∼50 μm on edge), were grown for the first time. Synchrotron X-ray single-crystal diffraction unambiguously determined that the newfound β-NaYbO2 belongs to the three-dimensional pyrochlore structure characterized by the R3̅m space group, corroborated by synchrotron X-ray and neutron powder diffraction and pair distribution function. Magnetic measurements revealed no long-range magnetic order or spin glass behavior down to 0.4 K with a low boundary spin frustration factor of 17.5, suggesting a potential QSL ground state. Under high magnetic fields, the potential QSL state was broken and spins order. Our findings reveal that NaYbO2 is a fertile playground for studying novel quantum states.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Observing low-altitude features in ozone concentrations in a shoreline environment via uncrewed aerial systems

Abstract. Ozone is a pollutant formed in the atmosphere by photochemical processes involving nitrogen oxides (NOx) and volatile organic compounds (VOCs) when exposed to sunlight. Tropospheric boundary layer ozone is regularly measured at ground stations and sampled infrequently through balloon, lidar, and crewed aircraft platforms, which have demonstrated characteristic patterns with altitude. Here, to better resolve vertical profiles of ozone within the atmospheric boundary layer, we developed and evaluated an uncrewed aircraft system (UAS) platform for measuring ozone and meteorological parameters of temperature, pressure, and humidity. To evaluate this approach, a UAS was flown with a portable ozone monitor and a meteorological temperature and humidity sensor to compare to tall tower measurements in northern Wisconsin. In June 2020, as a part of the WiscoDISCO20 campaign, a DJI M600 hexacopter UAS was flown with the same sensors to measure Lake Michigan shoreline ozone concentrations. This latter UAS experiment revealed a low-altitude structure in ozone concentrations in a shoreline environment showing the highest ozone at altitudes from 20–100 m a.g.l. These first such measurements of low-altitude ozone via a UAS in the Great Lakes region revealed a very shallow layer of ozone-rich air lying above the surface.

Meteorology & Atmospheric Sciences↗

DOE OSTI2020

Morphological and nanomechanical changes in tungsten in high heat flux conditions

Abstract Morphological and nanomechanical alteration of tungsten in extreme environments, like those in edge localized modes in nuclear fusion environments, up to 46.3 GWm −2 heat fluxes were experimentally simulated using electrothermal plasma. Surface and subsurface damage to the tungsten is seen mainly in the form of pore formation, cracks, and resolidified melt instabilities. Mirco voids, rosette-type microfeatures, core-shell structure, particle enrichment, and submicron channels all manifest in the damaged subsurface. The formation of voids in the subsurface was determined to originate from the ductile fracture of hot tungsten by plastic flow but not developed to cracking. The voids were preferentially settled in grain boundaries, interfaces. The directionality of elongated voids and grains is biased to the heat flow vector or plasma pathway, which is the likely consequence of the thermally driven grain growth and sliding in the high-temperature conditions. The presence of a border between the transient layer and heat-affected zone is observed and attributed to plasma shock and thermal spallation of fractural tungsten at high temperature. Plasma peening-like hardening effects in tungsten were observed in the range of 22.7–46.3 GWm −2 but least in the case of the lowest heat flux, 12.5 GWm −2 .

36 MATERIALS SCIENCE↗

DOE OSTI2024

Highly Responsive Polar Vortices in All‐Ferroelectric Heterostructures

Abstract The discovery of polar vortices and skyrmions in ferroelectric‐dielectric superlattices [such as (PbTiO 3 ) n /(SrTiO 3 ) n ] has ushered in an era of novel dipolar topologies and corresponding emergent phenomena. The key to creating such emergent features has generally been considered to be related to counterpoising strongly polar and non‐polar materials thus creating the appropriate boundary conditions. This limits the utility these materials can have, however, by rendering (effectively) half of the structure unresponsive to applied stimuli. Here, using advanced thin‐film deposition and an array of characterization and simulation approaches, polar vortices are realized in all‐ferroelectric trilayers, multilayers, and superlattices built from the fundamental building block of (PbTiO 3 ) n /(Pb x Sr 1− x TiO 3 ) n wherein in‐plane ferroelectric polarization in the Pb x Sr 1− x TiO 3 provides the appropriate boundary conditions. These superlattices exhibit substantially enhanced electromechanical and ferroelectric responses in the out‐of‐plane direction that arise from the ability of the polarization in both layers to rotate to the out‐of‐plane direction under field. In the in‐plane direction, the layers are found to be strongly coupled during switching and when heterostructured with ferroelectric‐dielectric building blocks, it is possible to produce multistate switching. This approach expands the realm of systems supporting emergent dipolar texture formation and does so with entirely ferroelectric materials thus greatly improving their responses.

Kavle, Pravin↗

DOE OSTI2023

TRACER-Uncrewed Aircraft System (TRACER-UAS) Field Campaign Report

Convective processes drive the development of clouds across a variety of scales, thereby playing a central role in governing weather and climate globally. These processes help to set the stage for circulations that redistribute heat and moisture throughout the lower atmosphere, and simultaneously develop storms that supply precipitation to regions that depend on such rain events for supporting a variety of societal needs. At the same time, extreme precipitation events can result in localized flooding of low-lying areas, posing hazards to transportation and regional inhabitants, and potentially damaging structures and infrastructure. As a result, there is an inherent need to better understand the drivers and modulators of clouds and precipitation and leverage such understanding to make projections of how these important systems may evolve with a changing climate. With nearly three billion of Earth’s human inhabitants living within 200 km of a shoreline, development of such understanding is particularly important in coastal regimes. Central drivers of convective cloud development and life cycle in coastal environments include synoptic forcing, local meso- and microscale circulation regimes, microphysical evolution, and aerosol properties. Atmospheric boundary layer (ABL) development and its evolution can help drive the formation and organization of convective clouds, which then impart their own controls through dynamic processes related to latent heating and cooling (including cold-pool formation and propagation), three-dimensional radiative effects, and background environmental conditions (Fan et al. 2016). Such clouds have been contributing to record precipitation events in southeast Texas in recent years, relative to the last several decades of data from regional precipitation gauges (Fagnant et al. 2020). The greater Houston urban area has experienced particularly large increases in the frequency of extreme rainfall events, with enhanced intensity of extreme events (stretching of distribution tails) having potentially significant implications for watershed floodplain planning and mapping in greater Houston and Harris County. While the most extreme precipitation events were associated with tropical cyclones (e.g., Tropical Storm Allison and Hurricane Harvey; Blood 2014, Kao et al. 2019), strong thunderstorms can also deliver large amounts of precipitation over the area over relatively short periods.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2020

Phenomenological description of bright domain walls in ferroelectric-antiferroelectric layered chalcogenides

Recently, a layered ferroelectric CuIn P 2 Se 6 was shown to exhibit domain walls with locally enhanced piezoresponse—a striking departure from the observations of nominally zero piezoresponse in most ferroelectrics. Although it was proposed that such "bright" domain walls are phase boundaries between ferri- and antiferroelectrically ordered regions of the materials, the physical mechanisms behind the existence and response of these boundaries remain to be understood. Here, using Landau-Ginzburg-Devonshire phenomenology combined with a four sublattices model, we describe quantitatively the bright-contrast and dark-contrast domain boundaries between the antiferroelectric, ferroelectric, or ferrielectric long-range-ordered phases in a layered ferroelectric-antiferroelectric ferroics, such as CuIn P 2 (S 1-y Se y ) 6 .

36 MATERIALS SCIENCE↗

DOE OSTI2022

Do Arctic mixed-phase clouds sometimes dissipate due to insufficient aerosol? Evidence from comparisons between observations and idealized simulations

Abstract. Mixed-phase clouds are ubiquitous in the Arctic. These clouds can persist for days and dissipate in a matter of hours. It is sometimes unknown what causes this sudden dissipation, but aerosol–cloud interactions may be involved. Arctic aerosol concentrations can be low enough to affect cloud formation and structure, and it has been hypothesized that, in some instances, concentrations can drop below some critical value needed to maintain a cloud. We use observations from a Department of Energy ARM site on the northern slope of Alaska at Oliktok Point (OLI), the Arctic Summer Cloud Ocean Study (ASCOS) field campaign in the high Arctic Ocean, and the Integrated Characterisation of Energy, Clouds, Atmospheric state, and Precipitation at Summit – Aerosol Cloud Experiment (ICECAPS-ACE) project at the NSF (National Science Foundation) Summit Station in Greenland (SMT) to identify one case per site where Arctic boundary layer clouds dissipated coincidentally with a decrease in surface aerosol concentrations. These cases are used to initialize idealized large eddy simulations (LESs) in which aerosol concentrations are held constant until, at a specified time, all aerosols are removed instantaneously – effectively creating an extreme case of aerosol-limited dissipation which represents the fastest a cloud could possibly dissipate via this process. These LESs are compared against the observed data to determine whether cases could, potentially, be dissipating due to insufficient aerosol. The OLI case's observed liquid water path (LWP) dissipated faster than its simulation, indicating that other processes are likely the primary drivers of the dissipation. The ASCOS and SMT observed LWP dissipated at similar rates to their respective simulations, suggesting that aerosol-limited dissipation may be occurring in these instances. We also find that the microphysical response to this extreme aerosol forcing depends greatly on the specific case being simulated. Cases with drizzling liquid layers are simulated to dissipate by accelerating precipitation when aerosol is removed while the case with a non-drizzling liquid layer dissipates quickly, possibly glaciating via the Wegener–Bergeron–Findeisen (WBF) process. The non-drizzling case is also more sensitive to ice-nucleating particle (INP) concentrations than the drizzling cases. Overall, the simulations suggest that aerosol-limited cloud dissipation in the Arctic is plausible and that there are at least two microphysical pathways by which aerosol-limited dissipation can occur.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Exsolution-Driven Surface Transformation in the Host Oxide

Exsolution synthesizes self-assembled metal nanoparticle catalysts via phase precipitation. An overlooked aspect in this method thus far is how exsolution affects the host oxide surface chemistry and structure. Such information is critical as the oxide itself can also contribute to the overall catalytic activity. Here, combining X-ray and electron probes, we investigated the surface transformation of thin-film SrTi 0.65 Fe 0.35 O 3 during Fe 0 exsolution. We found that exsolution generates a highly Fe-deficient near-surface layer of about 2 nm thick. Moreover, the originally single-crystalline oxide near-surface region became partially polycrystalline after exsolution. Such drastic transformations at the surface of the oxide are important because the exsolution-induced nonstoichiometry and grain boundaries can alter the oxide ion transport and oxygen exchange kinetics and, hence, the catalytic activity toward water splitting or hydrogen oxidation reactions. These findings highlight the need to consider the exsolved oxide surface, in addition to the metal nanoparticles, in designing the exsolved nanocatalysts.

36 MATERIALS SCIENCE↗