Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compressive stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Real-time (nanoseconds) determination of liquid phase growth during shock-induced melting

Melting of solids is a fundamental natural phenomenon whose pressure dependence has been of interest for nearly a century. However, the temporal evolution of the molten phase under pressure has eluded measurements because of experimental challenges. By using the shock front as a fiducial, we investigated the time-dependent growth of the molten phase in shock-compressed germanium. In situ x-ray diffraction measurements at different times (1 to 6 nanoseconds) behind the shock front quantified the real-time growth of the liquid phase at several peak stresses. These results show that the characteristic time for melting in shock-compressed germanium decreases from ~7.2 nanoseconds at 35 gigapascals to less than 1 nanosecond at 42 gigapascals. Our melting kinetics results suggest the need to consider heterogeneous nucleation as a mechanism for shock-induced melting and provide an approach to measuring melting kinetics in shock-compressed solids.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Plastic deformation of single crystals of the equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy in tension and compression from 10 K to 1273 K

In this report the plastic deformation behavior of single crystals of the quinary, equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy (HEA) with the face-centered cubic structure has been investigated in tension and compression as a function of crystal orientation and temperature from 10 K to 1373 K. The critical resolved shear stress (CRSS) for {111}<110> slip at room temperature is 42-45 MPa. It does not depend much on crystal orientation (i.e., the Schmid law holds true) and the sense (tension vs. compression) of the applied load. The CRSS for {111}<110> slip increases with the decrease in temperature, without showing any significant inertia effects at cryogenic temperatures below 77 K. Extrapolation from the measured yield stresses down to 10 K yields a CRSS value at 0 K of 168 MPa. At cryogenic temperatures, the measured strain-rate sensitivity of flow stress is consistent with a very small activation volume. The concept of stress equivalence holds true both for the temperature dependence of CRSS and the stress dependence of activation volume, indicating that solid-solution hardening is the major strengthening mechanism. Deformation twinning occurs at 77 K but not at room temperature, resulting in higher tensile elongation to failure at 77 K than at room temperature. Deformation twinning at 77 K occurs at a shear stress of 378 MPa on conjugate ($\bar1\bar11$) planes in the form of Lüders deformation after large plastic strain (about 85%) achieved by the stage I (easy glide) and stage II (linear work-hardening) deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Predicting non-linear stress–strain response of mesostructured cellular materials using supervised autoencoder

Recent breakthroughs in advanced manufacturing capabilities have made it possible to design and print sophisticated topologies of cellular structures using diverse engineering materials such as metals, polymers, and ceramics. In these architectured materials, it is often desirable to tailor the mechanical properties by altering the unit cell topology. This necessitates an in-depth understanding of how the topology of the unit cell structure affects the macroscopic behavior of the material in both the linear and the non-linear regimes encountered under large compression. Here, we have developed a machine learning (ML) approach capable of accelerating the prediction of the stress–strain response of a polymer-based cellular structure under uniaxial confined compression. As part of generating the training data for ML, 60,000 mesostructures were generated using a relatively novel approach based on cellular automata, and their corresponding stress–strain responses were obtained from the finite element simulations. Principal component analysis (PCA) was used to reduce the dimensionality of the stress–strain curves. With only 20 principal components, PCA captured 99.89% of the variance in the stress–strain curves while reducing the dimensionality by 5X. ML using supervised autoencoder was able to successfully speed up the prediction of the non-linear stress–strain response of a unit cell by up to 4600X. The proposed method can serve as an efficient data generation tool and a rapid means for predicting the structure–property relationship through accelerated forward modeling of cellular materials under compaction, in cases where the macroscopic stress–strain response is governed by the unit-cell topology.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Quantitative kinetic rules for plastic strain-induced α - ω phase transformation in Zr under high pressure

Plastic strain-induced phase transformations (PTs) and chemical reactions under high pressure are broadly spread in modern technologies, friction and wear, geophysics, and astrogeology. However, because of very heterogeneous fields of plastic strain $E$ p and stress σ tensors and volume fraction c of phases in a sample compressed in a diamond anvil cell (DAC) and impossibility of measurements of σ and $E$ p , there are no strict kinetic equations for them. Here, we develop a kinetic model, finite element method (FEM) approach, and combined FEM-experimental approaches to determine all fields in strongly plastically predeformed Zr compressed in DAC, and specific kinetic equation for α-ω PT consistent with experimental data for the entire sample. Since all fields in the sample are very heterogeneous, data are obtained for numerous complex 7D paths in the space of 3 components of the plastic strain tensor and 4 components of the stress tensor. Kinetic equation depends on accumulated plastic strain (instead of time) and pressure and is independent of plastic strain and deviatoric stress tensors, i.e., it can be applied for various above processes. Our results initiate kinetic studies of strain-induced PTs and provide efforts toward more comprehensive understanding of material behavior in extreme conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Analyzing the Validity of Brazilian Testing Using Digital Image Correlation and Numerical Simulation Techniques

Characterizing the mechanical behavior of rocks plays a crucial role to optimize the fracturing process in unconventional reservoirs. However, due to the intrinsic anisotropy and heterogeneity in unconventional resources, fracture process prediction remains the most significant challenge for sustainable and economic hydrocarbon production. During the deformation tracking under compression, deploying conventional methods (strain gauge, extensometer, etc.) is insufficient to measure the deformation since the physical attachment of the device is restricted to the size of the sample, monitoring limited point-wise deformation, producing difficulties in data retrieval, and a tendency to lose track in failure points, etc. Where conventional methods are limited, the application of digital image correlation (DIC) provides detailed and additional information of strain evolution and fracture patterns under loading. DIC is an image-based optical method that records an object with a camera and monitors the random contrast speckle pattern painted on the facing surface of the specimen. To overcome the existing limitations, this paper presents numerical modeling of Brazilian disc tests under quasi-static conditions to understand the full-field deformation behaviors and finally, it is validated by DIC. As the direct tensile test has limitations in sample preparation and test execution, the Brazilian testing principle is commonly used to evaluate indirectly the tensile strength of rocks. The two-dimensional numerical model was built to predict the stress distribution and full-field deformation on Brazilian disc under compression based on the assumptions of a homogenous, isotropic and linear elastic material. The uniaxial compression test was conducted using the DIC technique to determine the elastic properties of Spider Berea sandstone, which were used as inputs for the simulation model. The model was verified by the analytical solution and compared with the digital image correlation. The numerical simulation results showed that the solutions matched reasonably with the analytical solutions where the maximum deviation of stress distribution was obtained as 14.59%. The strain evolution (normal and shear strains) and displacements along the central horizontal and vertical planes were investigated in three distinguishable percentages of peak loads (20%, 40%, and 90%) to understand the deformation behaviors in rock. The simulation results demonstrated that the strain evolution contours consistently matched with DIC generated contours with a reasonable agreement. The changes in displacement along the central horizontal and vertical planes showed that numerical simulation and DIC generated experimental results were repeatable and matched closely. In terms of validation, Brazilian testing to measure the indirect tensile strength of rocks is still an issue of debate. The numerical model of fracture propagation supported by digital image correlation from this study can be used to explain the fracturing process in the homogeneous material and can be extended to non-homogeneous cases by incorporating heterogeneity, which is essential for rock mechanics field applications.

58 GEOSCIENCES↗
DOE OSTI2021

Evolution of texture and internal stresses within polycrystalline rock salt using in situ 3D synchrotron computed tomography and 3D X-ray diffraction

Over time rock salt caverns have been extensively used as reliable repositories for hazardous waste such as nuclear waste, oil or compressed gases. Undisturbed rock salt deposits in nature are usually impermeable and have very low porosity. However, rock salt formations under excavation stresses can develop crack networks, which increase their porosities; and in the case of a connected crack network within the media, rock salt may become permeable. Although the relationship between the permeability of rock salt and the applied stresses has been reported in the literature, a microscopic study that investigates the properties influencing this relationship, such as the evolution of texture and internal stresses, has yet to be conducted. This study employs in situ 3D synchrotron micro-computed tomography and 3D X-ray diffraction (3DXRD) on two small-scale polycrystalline rock salt specimens to investigate the evolution of the texture and internal stresses within the specimens. The 3DXRD technique measures the 3D crystal structure and lattice strains within rock salt grains. The specimens were prepared under 1D compression conditions and have shown an initial {111} preferred texture, a dominant {110}$\langle1\bar{1}0\rangle$ slip system and no fully connected crack network. The {111} preferred texture under the unconfined compression experiment became stronger, while the {111}$\langle1\bar{1}0\rangle$ slip system became more prominent. The specimens did not have a fully connected crack network until applied axial stresses reached about 30 MPa, at a point where the impermeability of the material becomes compromised due to the development of multiple major cracks.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Characteristics of Fluid‐Solid Interaction Constitutive Models Within Poroelastodynamics at Higher Strain‐Rates and Large Deformations Implemented in 1D

The large deformation, mixed formulation, finite element (FE) modeling approach presented in Irwin et al. 2024 is extended herein to include improved constitutive models for representing dynamic solid-fluid interactions at higher strain rates (𝒪⁢(1⁢0 2 −1⁢0 3 )⁢s −1 ) and larger overpressure magnitudes (𝒪⁡(1⁢0 2 )⁢kPa) within a biphasic soft porous material using Theory of Porous Media (TPM) at finite strain. Specifically, these constitutive modeling improvements are the following: (i) a more physically robust constitutive model for pore fluid seepage velocity via inclusion of pore fluid viscous stress, and (ii) a modified deformation-dependent-permeability model and updated hyperelastic constitutive model better suited for handling larger volumetric compressions and extensions. The novelty of the present work is mainly the contribution (i): inclusion of pore fluid viscous stress at higher strain-rate and large deformations, which requires 𝐶 1 continuity in the weak formulation, accomplished by employing Hermite cubic interpolation functions within a mixed nonlinear poromechanical finite element formulation. In (ii), the model is updated to weakly enforce solid phase incompressibility, such that this assumption is not violated numerically, which provides improved numerical stability for achieving larger overpressure magnitudes on 𝒪⁡(1⁢0 2 ) kPa, which were not achievable with the previous Kozeny–Carman model in Irwin et al. 2024. Also in (ii), the volumetric part of the solid skeleton free energy function is modified to ensure proper bounds on the solid skeleton Jacobian of deformation 𝐽 s related to incompressibility of the solid phase. Uniaxial strain, unidirectional flow examples at higher strain rates (𝒪⁢(1⁢0 2 −1⁢0 3 )⁢s −1 ) and larger deformations (up to 0.2 (or 20%) nominal axial strain) demonstrate the improved physical representation—and numerical stability—of these constitutive model improvements.

42 ENGINEERING↗
DOE OSTI2022

A Novel Rotating Flexure-Test Technique for Brittle Materials with Circular Geometries

The four-point bend test is one of the simplest and often the preferred flexural strength evaluation method for brittle materials. In this loading mode, fracture often initiates from a critical surface (or subsurface) flaw when subjected to a tensile stress state. However, if the critical flaw exists on the compression side of the test specimen, it may not activate to grow a crack and hence the resulting flexural strength will be higher than the true value. The goal of this study is to measure the true flexural strength of a solid or hollow cylindrical brittle specimen by ensuring that failure occurs at its weakest point by rotating along its longitudinal axis, thereby exposing and activating its critical surface flaw during a four-point bend test. A novel test fixture has been designed and fabricated, and the true flexural strengths of cylindrical brittle and quasi-brittle tubular specimens have been measured and compared to existing experimental data obtained through traditional four-point bend tests. In this work, experimental results showcase the orientation dependance on flexural strength for various materials. Additionally, similarities between experimental findings and those available in literature, including observations of fracture surfaces and relationships between surface roughness and material strength, are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Compressive strength improvements from noncircular carbon fibers: A numerical study

The benefits of high-performance unidirectional carbon fiber composites are limited in many cost-driven industries due to the high cost relative to alternative reinforcement fibers. Low-cost carbon fibers have been previously proposed, but the longitudinal compressive strength continues to be a limiting factor or studies are based on simplifications that warrant further analysis. A micromechanical model is used to (1) determine if the longitudinal compressive strength of composites can be improved with noncircular carbon fiber shapes and (2) characterize why some shapes are stronger than others in compression. In comparison to circular fibers, the results suggest that the strength can be increased by 10%–13% by using a specific six-lobe fiber shape and by 6%–9% for a three-lobe fiber shape. A slight increase is predicted in the compressive strength of the study two-lobe fiber but has the highest uncertainty and sensitivity to fiber orientation and misalignment direction. The underlying mechanism governing the compressive failure of the composites was linked to the unique stress fields created by the lobes, particularly the pressure stress in the matrix. Importantly, this work provides mechanics-based evidence of strength improvements from noncircular fiber shapes and insight on how matrix yielding is altered with alternative fiber shapes.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Anomalous softening of 3D printed elastomeric foam irradiated under compressive strain

Elastomeric foam is an essential component in many industrial and technological settings, primarily as thermal insulators and as positional/mechanical support cushions. In particular, silicone foam is utilized in harsh environments due to exceptional thermal and chemical stability. Under service conditions within certain applications such material gets exposed to a high dosage of gamma radiation, which can permanently alter the material’s structural and mechanical response properties. Most studies on gamma-exposure under inert or oxidative atmosphere indicate hardening of silicone foam, which is attributed to radiation-induced enhancement in chemical cross-linking. Here we report two contrasting effects depending on whether (non-oxidative) radiation exposure is carried out with the foam under zero or finite compressive strain. While in the former case we observe radiation-hardening consistent with previous studies, in the latter case (50% porous foam under 30% uniaxial compression) we see a monotonic decrease in Young’s modulus with increasing dosage, although solvent swelling experiments on the constituent rubber indicate a net increase in cross-link density independent of the state of strain. We quantitatively model all dose-dependent data using the Ogden Hyperfoam strain-energy function within the framework of Tobolsky two-network scheme and attribute the above anomaly to a combined effect of radiation-induced thickness change (compression set) and inherent nonlinearity in the foam’s stress-strain response.

Coarse-grained models↗
DOE OSTI2022

Mechanical Characterization of Loblolly Pine

Biorefineries are faced with various material flow challenges during feeding and handling, due to inherent variability and inhomogeneity of biomass feedstocks. This impacts the efficiency of refinery processes and unit operations. Proper characterization of bulk properties allows for optimal process design and reduction of overall costs. This work is aimed at evaluating the physical and mechanical properties that impact bulk flow of loblolly pine. Cyclic axial compression tests are performed to elucidate consolidation behavior under different stress conditions. The results are then used to develop correlations between material parameters (particle size, tissue type, moisture content) and Elastic Modulus of bulk samples.

09 BIOMASS FUELS↗
DOE OSTI2025

Summary of Graphite Data Stored within NDMAS

The Graphite Technology Development Project provides data to support the design of graphite core components within specific reactor service conditions of the next generation of high-temperature, gas-cooled nuclear reactors. Physical, mechanical, and thermal properties of nuclear grade graphite were characterized for specimens that were unirradiated, irradiated, and irradiated under various stress conditions. The material properties include diameter, length, mass, density, compressive strength, tensile strength, flexural strength, modulus, resistivity, thermal diffusivity, and thermal expansion coefficient. Baseline graphite specimens are unirradiated from different grades (2114, IG-110, NBG-17, NBG-18, and PCEA) and different types used in different characterization tests (compressive, flexural, tensile, one-inch cylinder, and quarter-inch cylinder). The Advanced Graphite Creep (AGC) irradiation specimens are from a much larger number of grades and cylinder types (creep, piggyback, and pencil). For baseline graphite, characterization data for 7,756 specimens extracted from thirteen graphite billets were captured to the NDMAS database. For AGC experiments, four irradiation campaigns have been completed: AGC-1, AGC-2, AGC-3, and AGC-4. The ongoing HDG-1 (High-Dose Graphite) experiment, which began irradiation with Cycle 168B on August 26, 2020, includes specimens previously irradiated in AGC-2 in addition to the specimens originally destined for AGC-5.. Besides the characterization data, the AGC data includes irradiation monitoring and physics data representing the irradiation conditions of AGC specimens. Currently, all data for AGC-1, AGC-2, and AGC-3 have been captured to the NDMAS database. Only AGC-4 pre-irradiation and irradiation monitoring data have been captured, and HDG-1 pre-irradiation data are in process of being captured for unirradiated specimens. To date, a total of 38,149 material property records have been captured into NDMAS database for baseline and AGC specimens. All characterization data are qualified for use according to their perspective data verification reports. For the AGC irradiation campaigns, a total of 41,502 qualified physics calculation records were added for AGC-1, AGC-2, and AGC-3. Finally, a total of 173,698,505 AGC irradiation monitoring data records (thermocouple temperature, gas flow rate, gas pressure, gas moisture, applied load, and specimen displacement) have been captured to NDMAS; the majority of those records (~94%) are qualified data records.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Rate-dependent strength and deformation heterogeneity of B4C-reinforced Al composite: Time-resolved imaging with synchrotron X-rays

Dynamic (up to 5500 s -1 ) and quasi-static compression tests are conducted on a 15 wt% B4C particle-reinforced Al (B 4 C/Al) composite. In situ, high-speed synchrotron X-ray phase contrast imaging and digital image correlation are employed to map mesoscale deformation fields at μm and μs scales. The bulk stress–strain curves show significant strain and strain-rate hardening under dynamic compression. The strain-rate sensitivity exponent is an order of magnitude higher at high strain rates (> 10 3 s -1 ) than that at low strain rates (< 10 -2 s -1 ). Strain field mapping demonstrates distinct compressive strain localizations for both quasi-static and dynamic loading. Nevertheless, compressive strain localizations appear denser in spacing under dynamic loading, owing to spontaneous dislocation nucleation in both weak and strong zones. This results in a higher density of geometrically necessary dislocations, which contributes to the higher strain and strain-rate hardening of B 4 C/Al under dynamic loading. Additionally, the ratio of the maximum local strain to the bulk average is 1.5, and the local strain-rate enhancement cannot explain the increased rate sensitivity of B 4 C/Al under dynamic loading. Therefore, the rate-dependent deformation heterogeneity dominates the strain-rate hardening of B 4 C/Al. Postmortem analyses help correlate deformation features to particle- and grain-scale microstructures, yielding consistent results with mesoscale strain fields.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic signal recovery in distribution grids using compressive lossy measurements

Distribution system state estimation requires reliable aggregation of the measured data. However, the large volume of the measured data imposes a significant stress on the underlying communication infrastructure. With the challenges associated with measurement availability, current distribution systems are typically unobservable. To cope with the unobservability issue, compressive sensing theory allows us to recover system state information from a small number of measurements provided the states of the distribution system exhibit sparsity. In this paper, we evaluate the robustness of an updated Kalman filtered modified compressive sensing (KF-ModCS) technique that dynamically estimates the grid states using a small fraction of measured data. In practice, measurements used for sparsity based state estimation may also be intermittent due to communication network induced losses. Further, to understand the effect of packet losses on KF-ModCS, we provide an upper bound for the expected variances of the state estimation error for a given rate of information loss. This upper bound is further improved if the support set of the sparse signal that characterizes the state dynamics does not change over time and/or the reduced model is observable. Simulations based on two practical data sets collected from actual customers in a distribution grid validate the theoretical results.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Deep learning for in situ data compression of large turbulent flow simulations

As the size of turbulent flow simulations continues to grow, in situ data compression is becoming increasingly important for visualization, analysis, and restart checkpointing. For these applications, single-pass compression techniques with low computational and communication overhead are crucial. In this paper we present a deep-learning approach to in situ compression using an autoencoder architecture that is customized for three-dimensional turbulent flows and is well suited for contemporary heterogeneous computing resources. The autoencoder is compared against a recently introduced randomized single-pass singular value decomposition (SVD) for three different canonical turbulent flows: decaying homogeneous isotropic turbulence, a Taylor-Green vortex, and turbulent channel flow. Our proposed fully convolutional autoencoder architecture compresses turbulent flow snapshots by a factor of 64 with a single pass, allows for arbitrarily sized input fields, is cheaper to compute than the randomized single-pass SVD for typical simulation sizes, performs well on unseen flow configurations, and has been made publicly available. The results reported here show that the autoencoder dramatically outperforms a randomized single-pass SVD with similar compression ratio and yields comparable performance to a higher-rank decomposition with an order of magnitude less compression in regard to preserving a number of important statistical quantities such as turbulent kinetic energy, enstrophy, and Reynolds stresses.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Quasi-isentropic compression of an additively manufactured aluminum alloy to 14.8 GPa

We uniaxially and shocklessly compressed an additively manufactured aluminum alloy, laser powder bed fusion (LPBF) AlSi10Mg, to peak stresses ranging from 4.4 to 14.8 GPa at peak strain rates on the order of [Formula: see text] via a series of magnetic loading experiments to measure the principal isentrope, yield strength, and shear modulus as a function of material orientation and applied stress. We did not observe significant anisotropy in any of the measured quantities. We found that the principal isentrope, within the uncertainty and up to our peak stress, overlaps the material’s Hugoniot. We measured yield strengths and shear moduli ranging from 0.28 to 0.81 GPa and 36 to 52 GPa, respectively. Our results indicate that LPBF AlSi10Mg behaves similarly to wrought Al alloys under quasi-isentropic compression.

Brown, Nathan P.↗
DOE OSTI2023

Crystallographic texture formation in Fe-9wt%Si alloy during deformation and phase transition at high pressure

SUMMARY The seismic anisotropy of the Earth's solid inner core has been the topic of much research. It could be explained by the crystallographic preferred orientation (CPO) developing during convection. The likely phase is hexagonal close-packed iron (hcp), alloyed with nickel and some lighter elements. Here we use high energy synchrotron X-rays to study CPO in Fe-9wt%Si, uniaxially compressed in a diamond anvil cell in radial geometry. The experiments reveal that strong preferred orientation forms in the low-pressure body-centred cubic (bcc) phase that appears to be softer than pure iron. CPO is attributed to dominant {110}<111> slip. The onset of the bcc→hcp transition occurs at a pressure of ≈15 GPa, and the alloy remains in a two phase bcc + hcp state up to 40 GPa. The hcp phase forms first with a distinct {11$\bar{2}$0} maximum perpendicular to compression. Modelling shows that this is a transformation texture, which can be described by Burgers orientation relationship with variant selection. Experimental results suggest that bcc grains oriented with <100> parallel to compression transform into hcp first. The CPO of the hcp changes only slowly during further pressure and deviatoric stress increase at ambient temperature. After heating to 1600 K, a change in the hcp CPO is observed with alignment of (0001) planes perpendicular to compression that can be interpreted as dominant (0001)<11$\bar{2}$0> slip, combined with {10$\bar{1}$2}<$\bar{1}$011> mechanical twinning, which is similar to the deformation modes suggested previously for pure hcp iron at inner core conditions.

Vasin, Roman N.↗
DOE OSTI2022

Apparatus for measuring strength in biaxial compression

We report most measurements of compressive strength of ductile materials have involved Hopkinson–Kolsky bars or Taylor anvils placing samples in uniaxial compression. In these geometries, strain is limited by the tendency of the sample to petal, in analogy to necking in uniaxial tension. Estimation of strength for any other form of the stress tensor requires assuming a shape of the yield surface; because data exist only for uniaxial compression, these assumptions are untested. In an imploding spherical shell, compression is biaxial, the plastic strain may not be small, and the material behavior may be nonlinear as a result of work hardening and heating by plastic work. We outline a method of measuring the strengths of materials in biaxial compression, both quasistatically and dynamically, using the compression of thin spherical shells. We suggest surrounding the shell with an annulus filled with a mixture of H 2 and Cl 2 gases whose homogeneous ignition is initiated by a flash of blue and near-ultraviolet light. Less promising approaches are described in Appendixes A–C .

47 OTHER INSTRUMENTATION↗