Static Stability and Control of Canard Configurations at Mach Numbers from 0.70 to 2.22 : Longitudinal Characteristics of a Triangular Wing and Canard
Explore the source record for details and available documents.
Boyd, John W↗
SEARCH · Search NASA
Results for “Configuration Control”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Alleviation of whirl-flutter on a joined-wing tilt-rotor aircraft configuration using active controls
The feasibility of using active controls to delay the onset of whirl-flutter on a joined-wing tilt rotor aircraft was investigated. The CAMRAD/JA code was used to obtain a set of linear differential equations which describe the motion of the joined-wing tilt-rotor aircraft. The hub motions due to wing/body motion is a standard input to CAMRAD/JA and were obtained from a structural dynamics model of a representative joined-wing tilt-rotor aircraft. The CAMRAD/JA output, consisting of the open-loop system matrices, and the airframe free vibration motion were input to a separate program which performed the closed-loop, active control calculations. An eigenvalue analysis was performed to determine the flutter stability of both open- and closed-loop systems. Sensor models, based upon the feedback of pure state variables and based upon hub-mounted sensors, providing physically measurable accelerations, were evaluated. It was shown that the onset of tilt-rotor whirl-flutter could be delayed from 240 to above 270 knots by feeding back vertical and span-wise accelerations, measured at the rotor hub, to the longitudinal cyclic pitch. Time response calculations at a 270-knot cruise condition showed an active cyclic pitch control level of 0.009 deg, which equates to a very acceptable 9 pound active-control force applied at the rotor hub.
Vanaken, Johannes M.↗
Static Stability and Control of Canard Configurations at Mach Numbers from 0.70 to 2.22 - Triangular Wing and Canard with Twin Vertical Tails
The static aerodynamic characteristics of a canard airplane configuration having twin vertical stabilizing surfaces are presented. The model consisted of a wing and canard both of triangular plan form and aspect ratio 2 mounted on a Sears-Haack body of fineness ratio 12.5 and two swept and tapered wing-mounted vertical tails of aspect ratio 1.35. Data are presented for Mach numbers from 0.70 to 2.22 and for angles of attack from -6 to +18 deg. at 0 and 5 deg. sideslip. Tests were made with the canard off and with the canard on. Nominal canard deflection angles ranged from 0 to 10 deg. The Reynolds number was 3.68 x 10(exp 6) based on the wing mean aerodynamic chord. Selected portions of the data obtained in this investigation are compared with previously published results for the same model having a single vertical tail instead of twin vertical tails. Without the canard, the directional stability at supersonic Mach numbers and high angles of attack was improved slightly by replacing the single tail with twin tails. However, at a Mach number of 0.70, the directional stability of the twin-tail model deteriorated rapidly with increasing angle of attack above 10 deg. and fell considerably below the level for the single-tail model. At subsonic speeds the directional stability of the twin-tail model with the canard was comparable to that for the single-tail model and at supersonic speed it was considerably greater at high angles of attack. Unlike the single-tail model, the twin-tail model at 50 sideslip exhibited an unstable break in the variation of pitching-moment coefficient with lift coefficient near 10 deg. angle of attack for 0.70 Mach number.
Peterson, Victor L.↗
Improved Re-Configurable Sliding Mode Controller for Reusable Launch Vehicle of Second Generation Addressing Aerodynamic Surface Failures and Thrust Deficiencies
In this report we present a time-varying sliding mode control (TV-SMC) technique for reusable launch vehicle (RLV) attitude control in ascent and entry flight phases. In ascent flight the guidance commands Euler roll, pitch and yaw angles, and in entry flight it commands the aerodynamic angles of bank, attack and sideslip. The controller employs a body rate inner loop and the attitude outer loop, which are separated in time-scale by the singular perturbation principle. The novelty of the TVSMC is that both the sliding surface and the boundary layer dynamics can be varied in real time using the PD-eigenvalue assignment technique. This salient feature is used to cope with control command saturation and integrator windup in the presence of severe disturbance or control effector failure, which enhances the robustness and fault tolerance of the controller. The TV-SMC is developed and tuned up for the X-33 sub-orbital technology demonstration vehicle in launch and re-entry modes. A variety of nominal, dispersion and failure scenarios have tested via high fidelity 6DOF simulations using MAVERIC/SLIM simulation software.
Shtessel, Yuri B.↗
Direct Adaptive Rejection of Vortex-Induced Disturbances for a Powered SPAR Platform
The Rapidly Deployable Stable Platform (RDSP) is a novel vessel designed to be a reconfigurable, stable at-sea platform. It consists of a detachable catamaran and spar, performing missions with the spar extending vertically below the catamaran and hoisting it completely out of the water. Multiple thrusters located along the spar allow it to be actively controlled in this configuration. A controller is presented in this work that uses an adaptive feedback algorithm in conjunction with Direct Adaptive Disturbance Rejection (DADR) to mitigate persistent, vortex-induced disturbances. Given the frequency of a disturbance, the nominal DADR scheme adaptively compensates for its unknown amplitude and phase. This algorithm is extended to adapt to a disturbance frequency that is only coarsely known by including a Phase Locked Loop (PLL). The PLL improves the frequency estimate on-line, allowing the modified controller to reduce vortex-induced motions by more than 95% using achievable thrust inputs.
VanZwieten, Tannen S.↗
NGSLR Safety Handbook
NASA's Next Generation Satellite Laser Ranging (NGSLR) station is the prototype for NASA's Satellite Laser Ranging (SLR) systems which will be deployed around the world in the coming decade. The NGSLR system will be an autonomous, photon-counting SLR station with an expected absolute range accuracy of better than one centimeter and a normal point (time-averaged) range precision better than one millimeter. The system provides continuous (weather permitting), 24 hour tracking coverage to an existing constellation of approximately two dozen artificial satellites equipped with passive retroreflector arrays, using pulsed, 532 nm, class IV laser systems. Current details on the approved laser systems can be found in the Appendix 1 of this document. This safety plan addresses the potential hazards to emitted laser radiation, which can occur both inside and outside the shelter. Hazards within the shelter are mitigated through posted warning signs, activated warning lights, procedural controls, personal protective equipment (PPE), laser curtains, beam blocking systems, interlock controls, pre-configured laser control settings, and other controls discussed in this document. Since the NGSLR is a satellite tracking system, laser hazards exist outside the shelter to personnel on the shelter roof and to passing aircraft. Potential exposure to personnel outside the system is mitigated through the use of posted warning signs, access control, procedural controls, a stairwell interlock, beam attenuation/blocking devices, and a radar based aircraft detection system.
satellite laser ranging↗
Autonomous Control for Arbitrary Thruster Configurations and Mass Properties in Special Euclidean Group SE(3)
Most current methods for determining maneuvers and thrust firing sequences depend on explicit and predetermined commands generated by a combination of on-board systems and ground-based human-in-the-loop methods. For spacecraft and space structures with changing mass properties and thruster configurations, such as the Deep Space Gateway as it changes configurations throughout its lifetime, determining these commands can be time-consuming and computationally intensive. However, recent work within the Lie GroupSE (3) has offered ways of autonomously determining the location, power, precision, and capabilities of thrusters in any arbitrary position. Furthermore, a method for determining thruster firing sequences based on an arbitrary control input (both translational and rotational in a coupled, 6-element vector) and arbitrary thruster configurations has also recently been developed. When combining these methods, any spacecraft with any mass properties and thruster configurations can be understood in terms of controllability limits and thruster firing sequences can be generated quickly and with low computational load, thus extending the autonomous capabilities of deep space missions. In this work, this method is presented and explored in terms of computational load, robustness in the presence of uncertainty, and overall performance. The capabilities of this method are also examined in the case of the Deep Space Gateway both in fully controllable configurations and uncontrollable configurations.
Control↗
A controllability-stabilizability result for the NASA-IEEE Spacecraft Control Laboratory Experiment (SCOLE) configuration
A nonlinear distributed parameter model for the NASA-Institute of Electrical and Electronics Engineers' Spacecraft Control Laboratory Experiment (SCOLE) configuration is considered. A linear feedback control law is proposed that points the line of sight of the antenna to any given target direction and at the same time stabilizes the oscillations of the entire flexible configuration.
Araya, Roberto↗
Autonomous Control for Arbitrary Thruster Configurations and Mass Properties in Special Euclidean Group SE(3)
Most current methods for determining maneuvers and thrust firing sequences depend on explicit and predetermined commands generated by a combination of on-board systems and ground-based human-in-the-loop methods. For spacecraft and space structures with changing mass properties and thruster configurations, such as the Deep Space Gateway as it changes configurations throughout its lifetime, determining these commands can be time-consuming and computationally intensive. However, recent work within the Lie group SE(3) has offered ways of autonomously determining the location, power, precision, and capabilities of thrusters in any arbitrary position. Furthermore, a method for determining thruster firing sequences based on an arbitrary control input (both translational and rotational in a coupled, 6-element vector) and arbitrary thruster configurations has also recently been developed. When combining these methods, any spacecraft with any mass properties and thruster configurations can be understood in terms of controllability limits and thruster firing sequences can be generated quickly and with low computational load, thus extending the autonomous capabilities of deep space missions. In this work, this method is presented and explored in terms of convergence time to the desired pose. The capabilities of this method are also examined in the case of the Deep Space Gateway both in fully controllable configurations and uncontrollable configurations.
SE(3)↗
Autonomous Constrained Control for Arbitrary Thruster Configurations of Gimbaling Thrusters in SE(3)
In order to develop robust autonomy in spacecraft, it is desirable to develop methods for guiding and controlling arbitrarily-configured spacecraft with any combination of thrusters of various types, i.e. either static reaction control system thrusters and gimbaling thrusters. Scenarios in which autonomous selection of thrusters may be needed include the case of a stuck or inhibited thruster that restricts the motion of the vehicle, vehicles with changing mass properties such as logistics modules or tugs, or vehicles that have imposed constraints on thrusters during docking in order to avoid plume impingement on a space station or adjacent spacecraft. To that end, a spacecraft must be able to rapidly and autonomously reconfigure thruster firing histories and update guidance protocols in accordance with newly imposed constraints. In this paper, a methodology is presented that enables a spacecraft to autonomously select thrusters of any configuration and type in order to optimally match a desired 6-degree-of-freedom navigation and control within the special Euclidean SE(3) framework. The residual motion imposed by off-nominal thruster configurations or thrusters that are not fully controllable is identified by the spacecraft and solved for over time, both for static reaction control systems and for the case of gimbaling thrusters.
GN&C↗
Design of robust line-of-sight pointing control system for the SCOLE configuration
Robust compensator design for attitude control of the Spacecraft Control Laboratory Experiment (SCOLE) configuration is considered. A loop-shaping procedure similar to that used in the LQG/LTR method is used to iteratively design the compensator. A satisfactory compensator is obtained by including the rigid modes and three elastic modes in the design model.
Joshi, S. M.↗
Second tracking and data relay satellite system (TDRSS) ground terminal - STGT
The STGT will provide high availability command and control and improved services to users of NASA's Space Network in the 1990s and beyond. The Space Network, comprising the TDRSS, will be the primary communications gateway for Space Station Freedom and other user's spacecraft and their ground support elements. The STGT will contain a redundant, distributed computer system providing configuration and control of redundant RF to baseband equipment chains for throughput of user data, for user tracking services and for control and monitoring of the TDR Satellites. An interface with NASA's Network Control Center, located at the Goddard Space Flight Center, provides automated scheduling and control of the STGT. A local TDRSS Operations Control Center for local monitoring and back-up control and an interface with the Domestic Satellite for data distribution will be provided by the STGT. This paper describes the STGT, with emphasis on configuration, control and monitoring of those elements providing TDRSS services to user spacecraft.
Berndt, Allen K.↗
Flight Control Role in RLV Configuration Development
A new optimization technique was used to aide in the selection of aerodynamic surfaces and Thrust Vectoring Control (TVC) based on maximizing control margin during ascent and entry portions of the trajectory. In order to meet the mass fraction requirement of RLV (Reusable Launch Vehicle), every substructure needed to be carefully designed to minimize the dry mass. The trajectory was designed to deliver the payload required for each mission subject to thermal and structural constraints. At each point on the trajectory the angle of attack and Mach number pair was used to calculate the control power required to trim and to stabilize the vehicle. The new optimization technique was based on finding the configuration that minimizes the control power peaks along the entire trajectory.
Youssef, Hussein↗
Control of the SCOLE configuration using distributed parameter models
A continuum model for the SCOLE configuration has been derived using transfer matrices. Controller designs for distributed parameter systems have been analyzed. Pole-assignment controller design is considered easy to implement but stability is not guaranteed. An explicit transfer function of dynamic controllers has been obtained and no model reduction is required before the controller is realized. One specific LQG controller for continuum models had been derived, but other optimal controllers for more general performances need to be studied.
Hsiao, Min-Hung↗
Integrated Flight and Propulsion Controls for Advanced Aircraft Configurations
The research vision of the NASA Lewis Research Center in the area of integrated flight and propulsion controls technologies is described. In particular the Integrated Method for Propulsion and Airframe Controls developed at the Lewis Research Center is described including its application to an advanced aircraft configuration. Additionally, future research directions in integrated controls are described.
Merrill, Walter↗
Integrated Flight and Propulsion Controls for Advanced Aircraft Configurations
The research vision of the NASA Lewis Research Center in the area of integrated flight and propulsion controls technologies is described. In particular, the integrated method for propulsion and airframe controls developed at the Lewis Research Center is described including its application to an advanced aircraft configuration. Additionally, future research directions in integrated controls are described.
Merrill, Walter↗
Longitudinal Stability and Control Characteristics at Mach Numbers from 0.70 to 2.22 of a Triangular Wing Configuration Equipped with a Canard Control, a Trailing-Edge-Flap Control or a Cambered Forebody
Results of an investigation to determine the static longitudinal stability and control characteristics of an aspect-ratio-2 triangular wing and body configuration equipped with either a canard control, a trailing-edge-flap control, or a cambered forebody are presented without analysis for Mach numbers from 0.70 to 2.22. The canard surface had a triangular plan form and a ratio of exposed area to total wing area of 7.8 percent. The hinge line of the canard was in the extended wing chord plane, 0.83 wing mean aerodynamic chord ahead of the reference center of moments. The trailing-edge controls were constant-chord full-span flaps with exposed area equal to 10.7 percent of the total wing area. The cambered body was a modified Sears-Haack body with camber only ahead of the wing apex. Data are presented for various canard and flap deflections at angles of attack ranging from -6 deg to +18 deg.
Boyd, John W.↗
Accuracy analysis of pointing control system of solar power station
The first-phase effort concentrated on defining the minimum basic functions that the retrodirective array must perform, identifying circuits that are capable of satisfying the basic functions, and looking at some of the error sources in the system and how they affect accuracy. The initial effort also examined three methods for generating torques for mechanical antenna control, performed a rough analysis of the flexible body characteristics of the solar collector, and defined a control system configuration for mechanical pointing control of the array.
Hung, J. C.↗