Results for “Cycling stability” — Page 20

NASA NTRS2011

Spectrally and Radiometrically Stable Wide-Band on Board Calibration Source for In-Flight Data Validation in Imaging Spectroscopy Applications

The quality of the quantitative spectral data collected by an imaging spectrometer instrument is critically dependent upon the accuracy of the spectral and radiometric calibration of the system. In order for the collected spectra to be scientifically useful, the calibration of the instrument must be precisely known not only prior to but during data collection. Thus, in addition to a rigorous in-lab calibration procedure, the airborne instruments designed and built by the NASA/JPL Imaging Spectroscopy Group incorporate an on board calibrator (OBC) system with the instrument to provide auxiliary in-use system calibration data. The output of the OBC source illuminates a target panel on the backside of the foreoptics shutter both before and after data collection. The OBC and in-lab calibration data sets are then used to validate and post-process the collected spectral image data. The resulting accuracy of the spectrometer output data is therefore integrally dependent upon the stability of the OBC source. In this paper we describe the design and application of the latest iteration of this novel device developed at NASA/JPL which integrates a halogen-cycle source with a precisely designed fiber coupling system and a fiber-based intensity monitoring feedback loop. The OBC source in this Airborne Testbed Spectrometer was run over a period of 15 hours while both the radiometric and spectral stabilities of the output were measured and demonstrated stability to within 1% of nominal.

visible spectrometers↗

NASA NTRS1973

Hollow cathodes with BaO impregnated, porous tungsten inserts and tips

The technology of impregnated materials is described and some inherently advantageous characteristics of impregnated cathodes are discussed. Thermionic emission measurements are presented for oxide coated and impregnated cathodes. Five cathode configurations with barium oxide impregnated porous tungsten inserts and/or tips have been fabricated and tested. Reliability, durability, and stability of operation are characterized. One of the cathodes has accumulated over 9000 operational hours, another has been cycled on and off more than 800 times.

Hudson, W. R.↗

NASA NTRS1973

Hollow cathodes with BaO impregnated, porous tungsten inserts and tips

The technology of impregnated materials is described and some inherently advantageous characteristics of impregnated cathodes are discussed. Thermionic emission measurements are presented for oxide coated and impregnated cathodes. Five cathode configurations with barium oxide impregnated porous tungsten inserts and/or tips have been fabricated and tested. Reliability, durability, and stability of operation are characterized. One of the cathodes has accumulated over 9000 operational hours, another has been cycled on and off more than 900 times.

Hudson, W. R.↗

NASA NTRS1989

Structural materials for space applications

The long-term performance of structural materials in the space environment is a key research activity within NASA. The primary concerns for materials in low Earth orbit (LEO) are atomic oxygen erosion and space debris impact. Atomic oxygen studies have included both laboratory exposures in atomic oxygen facilities and flight exposures using the Shuttle. Characterization of atomic oxygen interaction with materials has included surface recession rates, residual mechanical properties, optical property measurements, and surface analyses to establish chemical changes. The Long Duration Exposure Facility (LDEF) is scheduled to be retrieved in 1989 and is expected to provide a wealth of data on atomic oxygen erosion in space. Hypervelocity impact studies have been conducted to establish damage mechanisms and changes in mechanical properties. Samples from LDEF will be analyzed to determine the severity of space debris impact on coatings, films, and composites. Spacecraft placed in geosynchronous Earth orbit (GEO) will be subjected to high doses of ionizing radiation which for long term exposures will exceed the damage threshold of many polymeric materials. Radiation interaction with polymers can result in chain scission and/or cross-linking. The formation of low molecular weight products in the epoxy plasticize the matrix at elevated temperatures and embrittle the matrix at low temperatures. This affects both the matrix-dominated mechanical properties and the dimensional stability of the composite. Embrittlement of the matrix at low temperatures results in enhanced matrix microcracking during thermal cycling. Matrix microcracking changes the coefficient of thermal expansion (CTE) of composite laminates and produces permanent length changes. Residual stress calculations were performed to estimate the conditions necessary for microcrack development in unirradiated and irradiated composites. The effects of UV and electron exposure on the optical properties of transparent polymer films were also examined to establish the optimum chemical structure for good radiation resistance. Thoughts on approaches to establishing accelerated testing procedures are discussed.

Tenney, Darrel R.↗

NASA NTRS1990

Optimal stabilization of discrete event systems

An optimal stabilization problem for discrete event systems (DES) is addressed. A class of not necessarily finite state 'logical' DES models is utilized which can also model the costs for events to occur. Let P and A denote two such models. Suppose that P characterizes the valid behavior of a dynamical system and A represents certain design objectives which specify the allowable DES behavior which is 'contained in' the valid behavior. An optimal control problem for P and A is how to choose the sequence of inputs to P so that the DES behavior lies in A (i.e., it is allowable) and so that a performance index defined in terms of the costs of the events is minimized. Two solutions are provided to an optimal stabilization problem, i.e. how to find a sequence of inputs that results in an optimal state trajectory which cycles in a pre-specified set.

Passino, Kevin M.↗

NASA NTRSDate not supplied

Picometer-level metrology of test articles on the road to Habitable Worlds Observatory

The Habitable Worlds Observatory will revolutionize our understanding of the universe by directly detecting biosignatures on extrasolar planets and allow us to answer the question if we are alone in the universe. To accomplish the tight science goals associated with this mission, the development of an ultrastable observatory with a coronagraphic instrument is necessary. The observatory itself may need to stay stable on the order of 10 picometers over a wavefront control cycle, orders of magnitude more stable than what is required on current space missions. The metrology to verify stability requirements must be roughly a factor of ten more stable. The ultrastable laboratory at NASA’s Goddard Space Flight Center has further stabilized its testbed to allow for dynamic measurements on diffuse and specular objects on the order of single picometers, and we are currently measuring drifts on the orders of tens of picometers over different temporal bands. This paper will discuss the mechanical updates to the testbed setup, the analysis performed on several test articles, and the path forward on the road to measuring achieving the required stability for Habitable Worlds Observatory.

Inteferometry↗

NASA NTRSDate not supplied

Picometer-Level Metrology of Test Articles on the Road to Habitable Worlds Observatory

The Habitable Worlds Observatory will revolutionize our understanding of the universe by directly detecting biosignatures on extrasolar planets and allow us to answer the question if we are alone in the universe. To accomplish the tight science goals associated with this mission, the development of an ultrastable observatory with a coronagraphic instrument is necessary. The observatory itself may need to stay stable on the order of 10 picometers over a wavefront control cycle, orders of magnitude more stable than what is required on current space missions. The metrology to verify stability requirements must be roughly a factor of ten more stable. The ultrastable laboratory at NASA’s Goddard Space Flight Center has further stabilized its testbed to allow for dynamic measurements on diffuse and specular objects on the order of single picometers, and we are currently measuring drifts on the orders of tens of picometers over different temporal bands. This paper will discuss the mechanical updates to the testbed setup, the analysis performed on several test articles, and the path forward on the road to measuring achieving the required stability for Habitable Worlds Observatory.

Inteferometry↗

NASA NTRSDate not supplied

Picometer-Level Metrology on the Road to Habitable Worlds Observatory

The Habitable Worlds Observatory will revolutionize our understanding of the universe by directly detecting biosignatures on extrasolar planets and allow us to answer the question if we are alone in the universe. To accomplish the tight science goals associated with this mission, the development of an ultrastable observatory with a coronagraphic instrument is necessary. The observatory itself may need to stay stable on the order of 10 picometers over a wavefront control cycle, orders of magnitude more stable than what is required on current space missions. The metrology to verify stability requirements must be roughly a factor of ten more stable. The ultrastable laboratory at NASA’s Goddard Space Flight Center has further stabilized its testbed to allow for dynamic measurements on diffuse and specular objects on the order of single picometers, and we are currently measuring drifts on the orders of tens of picometers over different temporal bands. This paper will discuss the mechanical updates to the testbed setup, the analysis performed on several test articles, and the path forward on the road to measuring achieving the required stability for Habitable Worlds Observatory.

Inteferometry↗

NASA NTRS1983

Influence of unbalance on the nonlinear dynamical response and stability of flexible rotor-bearing systems

In this paper, some of the effects of unbalance on the nonlinear response and stability of flexible rotor-bearing systems is presented from both a theoretical and experimental standpoint. In a linear system, operating above its stability threshold, the amplitude of motion grows exponentially with time and the orbits become unbounded. In an actual system, this is not necessarily the case. The actual amplitudes of motion may be bounded due to various nonlinear effects in the system. These nonlinear effects cause limit cycles of motion. Nonlinear effects are inherent in fluid film bearings and seals. Other contributors to nonlinear effects are shafts, couplings and foundations. In addition to affecting the threshold of stability, the nonlinear effects can cause jump phenomena to occur at not only the critical speeds, but also at stability onset or restabilization speeds.

Gunter, E. J.↗

NASA NTRS1993

A model for the hydrologic and climatic behavior of water on Mars

An analysis is carried out of the hydrologic response of a water-rich Mars to climate change and to the physical and thermal evolution of its crust, with particular attention given to the potential role of the subsurface transport, assuming that the current models of insolation-driven change describe reasonably the atmospheric leg of the planet's long-term hydrologic cycle. Among the items considered are the thermal and hydrologic properties of the crust, the potential distribution of ground ice and ground water, the stability and replenishment of equatorial ground ice, basal melting and the polar mass balance, the thermal evolution of the early cryosphere, the recharge of the valley networks and outflow, and several processes that are likely to drive the large-scale vertical and horizontal transport of H2O within the crust. The results lead to the conclusion that subsurface transport has likely played an important role in the geomorphic evolution of the Martian surface and the long-term cycling of H2O between the atmosphere, polar caps, and near-surface crust.

Clifford, Stephen M.↗

NASA NTRS1959

Stability and Control Characteristics at Subsonic Speeds of a Flat-Top Arrowhead Wing-Body Combination

A wind-tunnel investigation was made to determine the longitudinal- and lateral-stability derivatives of a flat-top wing-body configuration at Mach numbers from 0.22 to 0.90 and Reynolds numbers of 3.5 and 17 million. The wing had a leading-edge sweepback of 78.9 deg and a cathedral of 45 deg on the outer panels. The tests included the determination of the effectiveness of elevon and rudder controls and also an investigation of ground effects. The model was tested at angles of attack up to 28 deg and angles of sideslip up to 18 deg. The dynamic response of this configuration has been determined from the wind-tunnel data for a simulated airplane having a wing loading of 17.7 pounds per square foot. The longitudinal data show a forward shift in aerodynamic center of 10 percent of the mean aerodynamic chord as the lift coefficient is increased above 0.1. Although flown in the lift range of decreasing stability, the simulated airplane did not encounter pitch-up in maneuvers initiated from steady level flight with zero static margin unless a load factor of 2.2 was exceeded. This maneuver margin was provided by a large value of pitching moment due to pitching velocity. The number of cycles to damp the Dutch roll mode to half amplitude, the time constants of the roll subsidence and spiral divergence modes, and control effectiveness in roll are computed. The lateral stability is shown to be positive but is marginal in meeting the military specifications for today's aircraft. An analog computer study has been made in five degrees of freedom (constant velocity) which illustrates that the handling characteristics are satisfactory. Several programed rolling maneuvers and coordinated turns also illustrate the handling qualities of the airplane.

Buell, Donald A.↗

NASA NTRS2003

Stabilized Fiber-Optic Distribution of Reference Frequency

An optoelectronic system distributes a reference signal of low noise and highly stabilized phase and frequency (100 MHz) from an atomic frequency standard to a remote facility at a distance up to tens of kilometers. The reference signal is transmitted to the remote station as amplitude modulation of an optical carrier signal propagating in an optical fiber. The stabilization scheme implemented in this system is intended particularly to suppress phase and frequency fluctuations caused by vibrations and by expansion and contraction of the optical fiber and other components in diurnal and seasonal heating and cooling cycles. The system (see figure) comprises several subsystems, the main one being (1) a hydrogen-maser or linear-ion-trap frequency standard in an environmentally controlled room in a signal-processing center (SPC), (2) a stabilized fiber-optic distribution assembly (SFODA), (3) a compensated sapphire oscillator (CSO) in an environmentally controlled room in the remote facility, (4) thermally stabilized distribution amplifiers and cabling from the environmentally controlled room to end users, and (5) performance- measuring equipment.

Calhoun, Malcolm↗

NASA NTRS1991

Variation of crack-opening stresses in three-dimensions - Finite thickness plate

A 3D elastic-plastic finite-element analysis is conducted to study crack-growth behavior of thin and thick center-cracked specimens under constant-amplitude loading conditions. The numerical analysis and the specimen configuration and loading are described for both the thin and thick conditions. Stabilized crack-opening stresses of interior and exterior regions are given as are the closure and opening profiles of the crack-surface plane after the tenth cycle. The effect of thickness is discussed with respect to the crack-opening stress levels and the plastic zones of the interior and exterior regions. A load-reduced-displacement technique allows the calculation of the crack-opening stresses at three locations on the crack surface plane. The constraint effect related to thickness gives a lower stabilized crack-opening stress level for the thick specimens.

Chermahini, R. G.↗

NASA NTRS1980

Single-mode laser studies: Design and performance of a fixed-wave length source and coupling of lasers to thin-film optical waveguides

A module developed for the generation of a stable single wavelength to be used for a fiber optic multiplexing scheme is described. The laser is driven with RZ pulses, and the temperature is stabilized thermoelectrically. The unit is capable of maintaining a fixed wavelength within about 6 A as the pulse duty cycle is changed between 0 and 100 percent. This is considered the most severe case, and much tighter tolerances are obtainable for constant input power coding schemes. Using a constricted double heterostructure laser, a wavelength shift of 0.083 A mA is obtained due to laser self-heating by a dc driving current. The thermoelectric unit is capable of maintaining a constant laser heat-sink temperature within 0.02 C. In addition, miniature lenses and couplers are described which allow efficient coupling of single wavelength modes of junction lasers to thin film optical waveguides. The design of the miniature cylinder lenses and the prism coupling techniques allow 2 mW of single wavelength mode junction laser light to b coupled into thin film waveguides using compact assemblies. Selective grating couplers are also studied.

Ladany, I.↗

NASA NTRS1988

Interpenetrating polymer network approach to tougher and more microcracking resistant high temperature polymers. I - LaRC-RP40

Interpenetrating polymer networks in the form of the LaRC-RP40 resin, prepared by the in situ polymerization of a thermosetting imide prepolymer and thermoplastic monomer reactants, are presently used to obtain toughness and microcracking resistance in a high-temperature polymer. Attention is presently given to the processing, physical, and mechanical properties, as well as the thermooxidative stability, of both the neat resin and the resin as a graphite fiber-reinforced matrix. Microcracking after thermal cycling was also tested. LaRC-RP40 exhibits significant resin fracture toughness improvements over the PMR-15 high-temperature matrix resin.

Pater, Ruth H.↗

NASA NTRS1993

Intraseasonal variability in a barotropic model with seasonal forcing

It has recently been suggested that oscillatory topographic instability could contribute to low-frequency variability over the Northern Hemisphere midlatitudes. A barotropic potential vorticity model, with a hierarchy of forcing and topography configurations on the sphere, is used to investigate the nature of low-frequency oscillations induced by such instabilities. Steady-state solutions of the model include multiple unstable equilibria that sustain oscillatory instabilities with periods of 10 - 15 days, and 150 - 180 days, for a realistic forcing pattern, Time-dependent solutions exhibit chaotic behavior with episodic oscillations, featuring both the intraseasonal (35 - 50 day) and biweekly (10 - 15 day) modes. The former is dominated by standing spatial patterns, the latter by traveling wave patterns. The phases of the intraseasonal oscillation are robust for all cases, exhibiting a clear oscillatory exchange of atmospheric angular momentum with the solid earth via mountain troque. It is demonstrated, through linear stability analysis on the sphere, that the intraseasonal oscillations are induced by topographic instabilities. The role of the seasonal cycle is studied by prescribing an annual cycle in the forcing. In this case, the winter forcing is more favorable than the summer for the occurrence of episodic intraseasonal oscillations. Recent observations are consistent with this model result.

Strong, Christopher M.↗

NASA NTRS2003

MAP Propulsion System Thermal Design

The propulsion system of the Microwave Anisotropy Probe (MAP) had stringent requirements that made the thermal design unique. To meet instrument stability requirements the system had to be designed to keep temperatures of all components within acceptable limits without heater cycling. Although the spacecraft remains at a fixed 22 sun angle at L2, the variations in solar constant, property degradation, and bus voltage range all significantly affect the temperature. Large portions of the fuel lines are external to the structure and all components are mounted to non-conductive composite structure. These two facts made the sensitivity to the MLI effective emissivity and bus temperature very high. Approximately two years prior to launch the propulsion system was redesigned to meet MAP requirements. The new design utilized hardware that was already installed in order to meet schedule constraints. The spacecraft design and the thermal requirements were changed to compensate for inadequacies of the existing hardware. The propulsion system consists of fuel lines, fill and drain lines/valve, eight thrusters, a HXCM, and a propulsion tank. A voltage regulator was added to keep critical components within limits. Software was developed to control the operational heaters. Trim resistors were put in series with each operational heater circuits and the tank survival heater. A highly sophisticated test program, which included real time model correlation, was developed to determine trim resistors sizes. These trim resistors were installed during a chamber break and verified during thermal balance testing.

Mosier, Carol L.↗

NASA NTRSDate not supplied

A Study of Large Scale Power Extraction and Insertion on Turbofan Performance and Stability

This paper describes the effects of turbofan power extraction and insertion (augmentation) on engine performance and stability. The purpose of this paper is to present how power augmentation affects a dual spool gas turbine engine cycle where the engine will also be required to provide thrust. The goals for the paper are to describe effective limits of power augmentation and offer strategies, utilizing spool choice and variable geometries, to maximize augmentation effect. While Analysis is general two potential uses are explored: Power extraction for electrified aircraft propulsion purposes. And, Power insertion for thrust assist. Results of the paper show it is possible to extract over 20% (at 85% max thrust) and gain roughly 12% of maximum thrust through power insertion.

Gas Turbine Engines↗