Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diameter effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

The effect of personal equation on measurements of the solar semi-diameter by transit circle observers

Cape Observatory transit circle measurements of systematic trends in the semi-diameter of the sun (1834, 1861-1871, 1884-1892) are considered, and an analysis of Washington six inch observations (1899-1903, 1911-1918, 1956-1971, 1975-1981) is given. A discordance between horizontal and vertical results in Cape measurements implies that these measurements are inaccurate due to the use of personal equations. The Washington measurements consider observational corrections and instrumental techniques, and it is thus concluded that no secular change in solar diameter has occurred.

Smith, C.↗
NASA NTRS1956

Jet Effects on Base and Afterbody Pressures of a Cylindrical Afterbody at Transonic Speeds

An investigation of the effects of jet nozzle geometry, size of base annulus, and base bleed upon the base and afterbody pressures of a cylindrical afterbody at transonic speeds has been conducted. Sonic and supersonic conical nozzles with jet-to-base diameter ratios from 0.25 to 0.85 were investigated with a cold jet at jet total-pressure ratios up to approximately 8.0 through a Mach number range from 0.6 to 1.25. Base pressure coefficients of about -0.55 were measured for the sonic nozzles at a Mach number of 1 or greater. The jet-to-base diameter ratio had a substantial effect on the base pressure obtained on the cylindrical afterbody of this investigation. Base bleed was beneficial in increasing the base pressure under certain conditions but had little or no effect at certain other conditions.

Cubbage, James M , Jr↗
NASA NTRS1984

Continuing Research at Solar Steam, Incorporated

The design and manufacture of two solar dish systems are discussed. A 30 foot diameter glass dish was designed, tested, and abandoned due to poor cost effectiveness during mass production. A 40 foot diameter glass dish that uses a single post wind abatement support carriage is under development.

Wood, D.↗
NASA NTRS1981

Electron beam induced damage in ITO coated Kapton

Data for the stability of thin conductive indium tin oxide films on 0.003 inch thick Kapton substrates during exposure of the surface to electron beams are reported. The electron beam energy was 3 keV and the diameter was about 0.8 mm. Thermal effects and surface modifications are considered. For primary current greater than 0.6 microamperes, an obvious dark discoloration with diameter approximately that of the beam was produced. The structure of the discolored region was studied with the scanning electron microscope, and the findings are stated. Surface modifications were explored by AES, obtaining spectra and secondary emission coefficient as a function of time for different beam intensities. In all cases beam exposure results in a decrease of the secondary yield but because of thermal effects this change, as well as composition changes, cannot be directly interpreted in terms of electron beam dosage.

Krainsky, I.↗
NASA NTRS1987

The interference of the model support mast with measurements of the longitudinal and lateral aerodynamic coefficients

The effects the single-bottom support masts used in the ONERA S1 and S4 wind tunnels have on aerodynamic data collected with scale model aircraft were examined experimentally and analytically. Systematic studies were performed on the flow characteristics around different diameters for the mounts. Scaling methods used to make data from one wind tunnel correspond to data from the other are described. Airbus 320 models were introduced into the tests and mast-body flow interactions were observed. A summary is presented of restrictions on the mast diameters, relative to cylindrical model diameters, which will minimize the effects the masts have on longitudinal and lateral aerodynamic stability data.

Vandekreeke, C.↗
DOE OSTI2021

Implementation of two-phase gas transport into VERA for molten salt reactor analysis

Molten salt reactors (MSRs) are a class of next-generation nuclear reactors that have received recent industrial and research interest. A generalized species transport solver was implemented in the Virtual Environment for Reactor Applications (VERA) computing suite to extend this tool to analyze liquid-fueled MSRs. This core simulator has been extended to model the transport of fission product gases into a collection of circulating gas bubbles with the purpose of removing the gases. This paper presents the governing species transport equation, along with various nuclear source terms. Development of the source term for phase migration is discussed, along with a simplified interfacial area tracking method. Finally, a case study on a simplified MSR loop is presented in which modeling parameters were varied to assess their impact on gas removal. The steady state results show that parameters such as bubble diameter, gas injection rate and mass transfer coefficient have a low to moderate effect on the fraction of xenon in the core region. Removal efficiency has the greatest effect on the fraction in the core region. After the pump bowl, bubble diameter has a minor effect on the fraction of xenon in the gas void. Finally, these results point out that increasing parameters such as mass transfer coefficient, gas injection rate, and removal efficiency drives the xenon into the circulating gas void, while decreasing bubble diameter also drives xenon into the gas void by increasing interfacial area.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS2014

Long Hole Film Cooling Dataset for CFD Development - Flow and Film Effectiveness

An experiment investigating flow and heat transfer of long (length to diameter ratio of 18) cylindrical film cooling holes has been completed. In this paper, the thermal field in the flow and on the surface of the film cooled flat plate is presented for nominal freestream turbulence intensities of 1.5 and 8 percent. The holes are inclined at 30 deg above the downstream direction, injecting chilled air of density ratio 1.0 onto the surface of a flat plate. The diameter of the hole is 0.75 in. (approx. 0.02 m) with center to center spacing (pitch) of 3 hole diameters. Coolant was injected into the mainstream flow at nominal blowing ratios of 0.5, 1.0, 1.5, and 2.0. The Reynolds number of the freestream was approximately 11,000 based on hole diameter. Thermocouple surveys were used to characterize the thermal field. Infrared thermography was used to determine the adiabatic film effectiveness on the plate. Hotwire anemometry was used to provide flowfield physics and turbulence measurements. The results are compared to existing data in the literature. The aim of this work is to produce a benchmark dataset for Computational Fluid Dynamics (CFD) development to eliminate the effects of hole length to diameter ratio and to improve resolution in the near-hole region. In this report, a Time Filtered Navier Stokes (TFNS), also known as Partially Resolved Navier Stokes (PRNS), method that was implemented in the Glenn-HT code is used to model coolant-mainstream interaction. This method is a high fidelity unsteady method that aims to represent large scale flow features and mixing more accurately.

Shyam, Vikram↗
NASA NTRS1973

Performance of 30-cm ion thrusters with dished accelerator grids

Thirteen sets of dished accelerator grids were treated on five different 30 cm diameter bombardment thrusters to evaluate the effects of grid geometry variations on thruster discharge chamber performance. The dished grid parameters varied were: grid-to-grid spacing, screen and accelerator grid hole diameter, screen and accelerator open area fraction, compensation for beam divergence losses, and accelerator grid thickness. The effects on discharge chamber performance of main magnetic field changes, magnetic baffle current, cathode pole piece length and cathode position were also investigated.

Rawlin, V. K.↗
DOE OSTI2021

Flow reduction of hydrocarbon liquid in silica nanochannel: Insight from many-body dissipative particle dynamics simulations

A modified many-body dissipative particle dynamics (mDPD) model recently developed for realistic mesoscale multiphase flow simulations is rigorously parameterized, calibrated, and applied for elucidating the flow mechanisms of hydrocarbon liquids (i.e., heptane in this work) in amorphous silica cylindrical nanochannels with inner diameters ranging from 4.5 to 22.5 nm. The simulation results suggest the presence of a strong threshold of pressure gradient under which heptane cannot be driven to flow. The threshold for the 4.5 nm diameter pore is 10 to 100 times as high as for the 9–22.5 nm diameter pore, highlighting a remarkable nanoconfinement effect. Fluid viscosity is found to exhibit a shear-thinning phenomenon with intensity to weaken with increasing channel diameter — a phenomenon not observed in nanochannel flow of liquid water and gas in literature. Most remarkably, the radial profiles of average longitudinal flow velocity fitted by the modified Hagen-Poiseuille equation showed a negative slip length (–2.5% to –0.5% relative to the diameter) and a reduction of apparent permeability by 16% to 23%. Furthermore, this finding suggests silica nanochannels tend to deter hydrocarbon flow, a phenomenon that is opposed to the flow enhancement reported in most of the prior nanochannel flow studies in literature.

74 ATOMIC AND MOLECULAR PHYSICS↗
NASA NTRS1975

On the effective temperature of alpha Herculis A

Measurements of alpha Her A with the amplitude interferometer yield a uniform disk angular diameter of about 0.058 sec. The fundamental effective temperature, 2450 K, obtained from this measurement is in good accord with those of luminous stars of neighboring spectral types, and differs markedly from previous determinations.

Knapp, S. L.↗
NASA NTRS1961

Transition of the Laminar Boundary Layer on a Delta Wing with 74 degree Sweep in Free Flight at Mach Numbers from 2.8 to 5.3

The tests were conducted at Mach numbers from 2.8 to 5.3, with model surface temperatures small compared to boundary-layer recovery temperature. The effects of Mach number, temperature ratio, unit Reynolds number, leading-edge diameter, and angle of attack were investigated in an exploratory fashion. The effect of heat-transfer condition (i.e., wall temperature to total temperature ratio) and Mach number can not be separated explicitly in free-flight tests. However, the data of the present report, as well as those of NACA TN 3473, were found to be more consistent when plotted versus temperature ratio. Decreasing temperature ratio increased the transition Reynolds number. The effect of unit Reynolds number was small as was the effect of leading-edge diameter within the range tested. At small values of angle of attack, transition moved forward on the windward surface and rearward on the leeward surface. This trend was reversed at high angles of attack (6 deg to 18 deg). Possible reasons for this are the reduction of crossflow on the windward side and the influence of the lifting vortices on the leeward surface. When the transition results on the 740 delta wing were compared to data at similar test conditions for an unswept leading edge, the results bore out the results of earlier research at nearly zero heat transfer; namely, sweep causes a large reduction in the transition Reynolds number.

Chapman, Gary T.↗
DOE OSTI2021

Analysis of Electro-static Assisted Air Dehumidification

The removal of water vapor from the air to reduce relative humidity is a well-known indoor environmental comfort requirement. Common dehumidification approaches require a substantial amount of energy and usually involve the cooling of atmospheric humid air below its dew point or the use of absorbent/adsorbent materials to extract water vapor out of the air. More recently, researchers investigated the effect of electrostatic forces for enhancing water vapor condensation. However, the studies are limited, and there is a lack of correlations that can predict the dehumidification rate. Also, the findings from the literature focused mainly on small flow rates on the order of one to two cfm. Electrically-enhanced condensation consists of the use of highly charged particles, preferably highly charged water droplets, that attract polar water vapor molecules to their surfaces and promote condensation, a phenomenon known as dielectrophoresis. An effect of the electric charge is the reduction of the vapor pressure on the droplets' surface with respect to the saturated pressure predicted by the Kelvin equation. Consequently, the equilibrium between evaporation and condensation is shifted towards condensation. Following the application of the modified Kelvin-Thomson theory, we developed a preliminary physics-based model to predict an effective size range of the charged droplets for optimal dehumidification. The range resulted in about 2 to 4 μm in diameter, under few simplifying assumptions. The effect of the size and the charge of the electrosprayed droplets on the overall dehumidification rate was briefly discussed. The use of electrosprays to produce small but highly charged droplets was broadly discussed in this paper. The cone-jet mode was identified as the most suitable electrospray operational mode, and it generated droplets of small size and high electrical charge. The cone-jet stability was also analyzed in detail. The preliminary data of the present work and the model results indicated that several electrospray heads were required to achieve a 5% dehumidification rate for airflow rates of about 5 cfm.

Morcelli, Stefano↗
DOE OSTI2021

Analysis of New Data of Electro-static Assisted Air Dehumidification Processes

The removal of water vapor from the air to reduce relative humidity is a well-known indoor environmental comfort requirement. Common dehumidification approaches require a substantial amount of energy and usually involve the cooling of atmospheric humid air below its dew point or the use of absorbent/adsorbent materials to extract water vapor out of the air. More recently, researchers investigated the effect of electrostatic forces for enhancing water vapor condensation. However, the studies are limited, and there is a lack of correlations that can predict the dehumidification rate. Also, the findings from the literature focused mainly on small flow rates on the order of one to two cfm. Electrically-enhanced condensation consists of the use of highly charged particles, preferably highly charged water droplets, that attract polar water vapor molecules to their surfaces and promote condensation, a phenomenon known as dielectrophoresis. An effect of the electric charge is the reduction of the vapor pressure on the droplets' surface with respect to the saturated pressure predicted by the Kelvin equation. Consequently, the equilibrium between evaporation and condensation is shifted towards condensation. Following the application of the modified Kelvin-Thomson theory, we developed a preliminary physics-based model to predict an effective size range of the charged droplets for optimal dehumidification. The range resulted in about 2 to 4 m in diameter, under few simplifying assumptions. The effect of the size and the charge of the electrosprayed droplets on the overall dehumidification rate was briefly discussed. The use of electrosprays to produce small but highly charged droplets was broadly discussed in this paper. The cone-jet mode was identified as the most suitable electrospray operational mode, and it generated droplets of small size and high electrical charge. The cone-jet stability was also analyzed in detail. The preliminary data of the present work and the model results indicated that several electrospray heads were required to achieve a 5% dehumidification rate for airflow rates of about 5 cfm.

Morcelli, Stefano↗
NASA NTRS2021

Mineral Dust Cycle in the Multiscale Online Nonhydrostatic AtmospheRe CHemistry Model (Monarch) Version 2.0

We present the dust module in the Multiscale Online Non-hydrostatic AtmospheRe CHemistry model (MONARCH) version 2.0, a chemical weather prediction system that can be used for regional and global modeling at a range of resolutions. The representations of dust processes in MONARCH were upgraded with a focus on dust emission (emission parameterizations, entrainment thresholds, considerations of soil moisture and surface cover), lower boundary conditions (roughness, potential dust sources), and dust–radiation interactions. MONARCH now allows modeling of global and regional mineral dust cycles using fundamentally different paradigms, ranging from strongly simplified to physics-based parameterizations. We present a detailed description of these updates along with four global benchmark simulations, which use conceptually different dust emission parameterizations, and we evaluate the simulations against observations of dust optical depth. We determine key dust parameters, such as global annual emission/deposition flux, dust loading, dust optical depth, mass-extinction efficiency, single-scattering albedo, and direct radiative effects. For dust-particle diameters up to 20 µm, the total annual dust emission and deposition fluxes obtained with our four experiments range between about 3500 and 6000 Tg, which largely depend upon differences in the emitted size distribution. Considering ellipsoidal particle shapes and dust refractive indices that account for size-resolved mineralogy, we estimate the global total (longwave and shortwave) dust direct radiative effect (DRE) at the surface to range between about −0.90 and −0.63 W m−2 and at the top of the atmosphere between −0.20 and −0.28 W m−2. Our evaluation demonstrates that MONARCH is able to reproduce key features of the spatiotemporal variability of the global dust cycle with important and insightful differences between the different configurations.

Dust cycle↗
NASA NTRS1973

Performance of 30-cm ion thrusters with dished accelerator grids

Thirteen sets of dished accelerator grids were tested on five different 30-cm diameter bombardment thrustors to evaluate the effects of grid geometry variations on thrustor discharge chamber performance. The dished grid parameters varied were: grid-to-grid spacing, screen and accelerator grid hole-diameter, screen and accelerator open area fraction, compensation for beam divergence losses, and accelerator grid thickness. Also investigated were the effects on discharge chamber performance of main magnetic field changes, magnetic baffle current cathode pole piece length and cathode position.

Rawlin, V. K.↗
NASA NTRS1998

Damage Characteristics and Residual Strength of Composite Sandwich Panels Impacted with and Without Compression Loading

The results of an experimental study of the impact damage characteristics and residual strength of composite sandwich panels impacted with and without a compression loading are presented. Results of impact damage screening tests conducted to identify the impact-energy levels at which damage initiates and at which barely visible impact damage occurs in the impacted facesheet are discussed. Parametric effects studied in these tests include the impactor diameter, dropped-weight versus airgun-launched impactors, and the effect of the location of the impact site with respect to the panel boundaries. Residual strength results of panels tested in compression after impact are presented and compared with results of panels that are subjected to a compressive preload prior to being impacted.

McGowan, David M.↗
NASA NTRS1954

Effect on Drag of Longitudinal Positioning of Half-Submerged and Pylon-Mounted Douglas Aircraft Stores on a Fuselage with and without Cavities between Mach Numbers 0.9 and 1.8

The effect on drag of positioning symmetrically mounted Douglas Aircraft Company, Inc. stores in pairs on a parabolic fuselage of fineness ratio 10.0 has been determined by flight tests of rocket-propelled, zero-lift models through a range of Mach number from 0.9 to 1.8. The stores were mounted in half-submerged positions and on pylons and were tested in three longitudinal locations on the fuselage with the forward position being located at the maximum diameter of the fuselage. The effects on drag of removing the half-submerged stores or extending them outward on pylons also was investigated by tests of models with half-submerged-store cavities on the fuselage. Two pylons differing in airfoil section and thickness were tested at the forward position of the stores on the fuselage with cavities. The half-submerged stores gave the smallest drag increments, which were approximately equal regardless of their respective longitudinal locations. Removing the half-submerged stores to expose the cavities increased the drag increments from two to three times. For the pylon-mounted stores, the store in the midposition had less drag than in the forward or rear positions at supersonic speeds. Adding the half-submerged-store cavities to the pylon-mounted-store configurations reduced the drag at the rear position between Mach numbers 0.95 and 1.50 and increased the drag at the midposition throughout the speed range. Changing from the 6-percent-thick flat pylon to the 10-percent-thick airfoil pylon increased the total drag slightly above Mach number 1.10. Good agreement was obtain& between the experimental and theoretical interference drag coefficients for the pylon-mounted stores (without fuselage cavities} in the three longitudinal locations tested at Mach numbers 1.2 and 1.5.

Hoffman, Sherwood↗