Search NASA⌕ Search

SEARCH · Search NASA

Results for “Distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

KC-135 wing and winglet flight pressure distributions, loads, and wing deflection results with some wind tunnel comparisons

A full-scale winglet flight test on a KC-135 airplane with an upper winglet was conducted. Data were taken at Mach numbers from 0.70 to 0.82 at altitudes from 34,000 feet to 39,000 feet at stabilized flight conditions for wing/winglet configurations of basic wing tip, 15/-4 deg, 15/-2 deg, and 0/-4 deg winglet cant/incidence. An analysis of selected pressure distribution and data showed that with the basic wing tip, the flight and wind tunnel wing pressure distribution data showed good agreement. With winglets installed, the effects on the wing pressure distribution were mainly near the tip. Also, the flight and wind tunnel winglet pressure distributions had some significant differences primarily due to the oilcanning in flight. However, in general, the agreement was good. For the winglet cant and incidence configuration presented, the incidence had the largest effect on the winglet pressure distributions. The incremental flight wing deflection data showed that the semispan wind tunnel model did a reasonable job of simulating the aeroelastic effects at the wing tip. The flight loads data showed good agreement with predictions at the design point and also substantiated the predicted structural penalty (load increase) of the 15 deg cant/-2 deg incidence winglet configuration.

Montoya, L. C.↗
NASA NTRS1984

Definition, analysis and development of an optical data distribution network for integrated avionics and control systems. Part 2: Component development and system integration

Fiber optic transmission is emerging as an attractive concept in data distribution onboard civil aircraft. Development of an Optical Data Distribution Network for Integrated Avionics and Control Systems for commercial aircraft will provide a data distribution network that gives freedom from EMI-RFI and ground loop problems, eliminates crosstalk and short circuits, provides protection and immunity from lightning induced transients and give a large bandwidth data transmission capability. In addition there is a potential for significantly reducing the weight and increasing the reliability over conventional data distribution networks. Wavelength Division Multiplexing (WDM) is a candidate method for data communication between the various avionic subsystems. With WDM all systems could conceptually communicate with each other without time sharing and requiring complicated coding schemes for each computer and subsystem to recognize a message. However, the state of the art of optical technology limits the application of fiber optics in advanced integrated avionics and control systems. Therefore, it is necessary to address the architecture for a fiber optics data distribution system for integrated avionics and control systems as well as develop prototype components and systems.

Yen, H. W.↗
NASA NTRS1984

The influence of neutral winds on He(+) distributions in the equatorial ionospshere

The effects of F-region neutral winds on the distribution of He(+) in the equatorial ionosphere have been examined using a theoretical model and an observational data set. It is shown by the model that components of neutral wind in the magnetic meridian up to only 50 m/s can produce He(+) gradients in the northern and southern sectors of a flux tube that differ by more than 80 percent. This is associated with interhemisphere transport velocities of He(+) as large as 15 m/s at 800 km. A substantial latitude gradient in the He(+) distribution across the dip equator also results from the redistribution of He(+). The changes in the He(+) concentration at the dip equator and the latitude distribution of H(+) in response to different neutral wind components is determined from the model and used to construct longitude distributions of He(+) to compare with observations made at equinox. Good agreement between the calculations and observations is obtained both at the geographic and geomagnetic equators using the relationship between neutral winds, interhemispheric transport velocity and He(+) concentration derived from the model. If these relationships can be extrapolated to accommodate the different conditions expected during solstice, the He(+) distributions expected during this season can also be discussed.

Murphy, J. A.↗
NASA NTRS1984

Distribution of aurora and ionospheric currents observed simultaneously on a global scale

The instantaneous spatial distribution of auroral emissions is observed with auroral imaging photometers on board the spacecraft Dynamics Explorer 1 (DE 1) as ground-based meridian chains of magnetometers simultaneously detect the magnetic signatures of ionospheric and field-aligned currents flowing at northern polar latitudes. Ionospheric conductivities at nighttime auroral latitudes are estimated from the measured auroral luminosities and used with the measured polar magnetic variations to compute model distributions of ionospheric and field-aligned currents. Temporal resolution for the coordinated observations and model calculations is 12 minutes. Model ionospheric and field-aligned current distributions are overlayed on global auroral images to illustrate spatial relations on a global scale at the maximum epoch of an auroral substorm. Eccentric-dipole-latitude and magnetic-local-time coordinates are used. A model field-aligned current distribution is compared quantitatively with the distribution of field-aligned currents inferred from simultaneous observations by the DE-2 magnetometer.

Craven, J. D.↗
NASA NTRS1985

Finite Control in Underdamped Distributed Parameter Systems

Specifically, a class of distributed parameter systems is defined using Hilbert space methods based on a partial differential equation model of a structure. In this space a simple, easy to check definition of underdamping is constructed based on the well known single degree of freedom concept of critical damping. It is then shown that if a given distributed parameter system satisfies this definition, each mode of the modal expansion of the solution is in fact an underdamped function of time. It is noted that a distributed parameter system which is underdamped is also uniformly exponentially stable. By appealing to the work of Gibson, a finite dimensional model of the system will yield satisfactory control laws. Furthermore, it is shown that the assumption of the underdamping also allows straightforward computation of rough bounds on the magnitude of the unmodeled or residual modes for a modal truncation scheme. Hence, underdamped systems are precisely that class of distributed parameter systems which are not likely to have spillover problems and which will yield convergence of finite dimensional control laws to control laws which are optimal for the full distributed parameter model of the system.

Inman, D. J.↗
NASA NTRS1986

Description of a 20 Kilohertz power distribution system

A single phase, 440 VRMS, 20 kHz power distribution system with a regulated sinusoidal wave form is discussed. A single phase power system minimizes the wiring, sensing, and control complexities required in a multi-sourced redundantly distributed power system. The single phase addresses only the distribution link; mulitphase lower frequency inputs and outputs accommodation techniques are described. While the 440 V operating potential was initially selected for aircraft operating below 50,000 ft, this potential also appears suitable for space power systems. This voltage choice recognizes a reasonable upper limit for semiconductor ratings, yet will direct synthesis of 220 V, 3 power. A 20 kHz operating frequency was selected to be above the range of audibility, minimize the weight of reactive components, yet allow the construction of single power stages of 25 to 30 kW. The regulated sinusoidal distribution system has several advantages. With a regulated voltage, most ac/dc conversions involve rather simple transformer rectifier applications. A sinusoidal distribution system, when used in conjunction with zero crossing switching, represents a minimal source of EMI. The present state of 20 kHz power technology includes computer controls of voltage and/or frequency, low inductance cable, current limiting circuit protection, bi-directional power flow, and motor/generator operating using standard induction machines. A status update and description of each of these items and their significance is presented.

Hansen, I. G.↗
NASA NTRS1985

Parameter identification in distributed systems

This paper describes a method for the identification of the parameters entering into the equations of motion of distributed systems. Because the motion of distributed systems is described in terms of partial differential equations, these parameters are in general continuous functions of the spatial variables. For vibrating systems, these parameters ordinarily represent the mass, stiffness and damping distributions. In this paper, these distributions are expanded in terms of finite series of known functions of the spatial variables multiplied by undetermined coefficients. It is assumed that the nature of the equations of motion is known and that a limited number of eigenvalues and eigenfunctions is identified in advance. Use is then made of the least squares method, in conjunction with the eigenfunctions' orthogonality, to compute the undetermined coefficients, thus identifying the system distributed parameters. A method for the identification of the eigensolution is also presented. The procedure for the identification of the eigensolution and of the system parameters is demonstrated via a numerical example.

Baruh, H.↗
NASA NTRS1986

DE-1 observations of hole electron distribution functions and the cyclotron maser resonance

The hole electron distribution functions observed by the DE-1 satellite within inverted-V events at altitudes of between 9000 km and 15,000 km are examined as a possible free energy source for exciting Z-mode radiation through cyclotron maser resonance. In the DE-1 observations the hole distribution function had center velocities varying between 8000 km/s and 20,000 km/s, with the radii varying between 2000 km/s and 10,000 km/s. The observed distribution function is fitted by an exponential function around the center of the hole, and is used to calculate growth rates of Z-mode radiation. Growth rates as high as 0.001 of the electron gyrofrequency are obtained. It is also shown that the observed hole distribution functions can excite Z-mode radiation at wave frequencies slightly above the gyrofrequency, and wave propagation angles slightly below 90 deg in the source region. The results suggest that the hole distribution function could provide additional amplification for Z-mode waves in the auroral zone.

Lin, C. S.↗
NASA NTRS1986

On the applicability of relativistic dispersion to auroral zone electron distributions

An examination is made to identify appropriate times to include weakly relativistic wave dispersion in calculations of auroral zone electron distributions. Two dispersion relations are examined. First, solutions are found for a ring distribution of particles around a cold ambient plasma. The solutions are found only for modes near the electron gyrofrequency. A trapped mode which is decoupled from the freely propagating R-X mode of cold plasmas is found to be the most unstable mode. Wave dispersion is examined with a spherically symmetric Dory-Guest-Harris (DGH) distribution, which describes a shell distribution that has a peak momentum larger than the thermal spread. The trapped mode is again found to be the most unstable. The analysis indicates it is beneficial to include relativistic effects whenever calculating auroral plasma distributions, and that a simple model will have sufficient accuracy.

Strangeway, R. J.↗
NASA NTRS1986

Description of a 20 kilohertz power distribution system

A single phase, 440 VRMS, 20 kHz power distribution system with a regulated sinusoidal wave form is discussed. A single phase power system minimizes the wiring, sensing, and control complexities required in a multi-sourced redundantly distributed power system. The single phase addresses only the distribution links multiphase lower frequency inputs and outputs accommodation techniques are described. While the 440 V operating potential was initially selected for aircraft operating below 50,000 ft, this potential also appears suitable for space power systems. This voltage choice recognizes a reasonable upper limit for semiconductor ratings, yet will direct synthesis of 220 V, 3 power. A 20 kHz operating frequency was selected to be above the range of audibility, minimize the weight of reactive components, yet allow the construction of single power stages of 25 to 30 kW. The regulated sinusoidal distribution system has several advantages. With a regulated voltage, most ac/dc conversions involve rather simple transformer rectifier applications. A sinusoidal distribution system, when used in conjunction with zero crossing switching, represents a minimal source of EMI. The present state of 20 kHz power technology includes computer controls of voltage and/or frequency, low inductance cable, current limiting circuit protection, bi-directional power flow, and motor/generator operating using standard induction machines. A status update and description of each of these items and their significance is presented.

Hansen, I. G.↗
NASA NTRS1988

The longitudinal and radial distribution of magnetic reconfigurations in the near-earth magnetotail as observed by AMPTE/CCE

The longitudinal and radial distribution of 103 substorm dipolarization events in the equatorial nightside magnetosphere from low altitude to about 9 R(E) observed by AMPTE/CCE is examined. The center of the distribution was located near midnight. For Kp of 3- or less, the distribution peak shifted toward the premidnight region, whereas for Kp of 4+ and higher, the distribution peak was inside the postmidnight region. The substorm frequency for the high-Kp case was about four times larger than the low-to-moderate-Kp case. The occurrence frequency of events increased with increasing radial distance, and no events were observed inside of 6.4 R(E). This radial distribution suggests that, on average, the substorm initiation region is greater than about 8 R(E). In addition, the average radial position of the signatures decreased with increasing Kp.

Lopez, R. E.↗
NASA NTRS1988

Application of the mobility power flow approach to structural response from distributed loading

The problem of the vibration power flow through coupled substructures when one of the substructures is subjected to a distributed load is addressed. In all the work performed thus far, point force excitation was considered. However, in the case of the excitation of an aircraft fuselage, distributed loading on the whole surface of a panel can be as important as the excitation from directly applied forces at defined locations on the structures. Thus using a mobility power flow approach, expressions are developed for the transmission of vibrational power between two coupled plate substructures in an L configuration, with one of the surfaces of one of the plate substructures being subjected to a distributed load. The types of distributed loads that are considered are a force load with an arbitrary function in space and a distributed load similar to that from acoustic excitation.

Cuschieri, J. M.↗
NASA NTRS1986

Comparing host and target environments for distributed Ada programs

The Ada programming language provides a means of specifying logical concurrency by using multitasking. Extending the Ada multitasking concurrency mechanism into a physically concurrent distributed environment which imposes its own requirements can lead to incompatibilities. These problems are discussed. Using distributed Ada for a target system may be appropriate, but when using the Ada language in a host environment, a multiprocessing model may be more suitable than retargeting an Ada compiler for the distributed environment. The tradeoffs between multitasking on distributed targets and multiprocessing on distributed hosts are discussed. Comparisons of the multitasking and multiprocessing models indicate different areas of application.

Paulk, Mark C.↗
NASA NTRS1988

Kanerva's sparse distributed memory: An associative memory algorithm well-suited to the Connection Machine

The advent of the Connection Machine profoundly changes the world of supercomputers. The highly nontraditional architecture makes possible the exploration of algorithms that were impractical for standard Von Neumann architectures. Sparse distributed memory (SDM) is an example of such an algorithm. Sparse distributed memory is a particularly simple and elegant formulation for an associative memory. The foundations for sparse distributed memory are described, and some simple examples of using the memory are presented. The relationship of sparse distributed memory to three important computational systems is shown: random-access memory, neural networks, and the cerebellum of the brain. Finally, the implementation of the algorithm for sparse distributed memory on the Connection Machine is discussed.

Rogers, David↗
NASA NTRS1989

The optical and near-infrared distribution of light in the edge-on galaxy IC 2531

Optical and near-IR imaging of the edge-on galaxy IC 2531 is presented, and an attempt is made to derive the true distributions of stars and dust in this galaxy. The results suggest that the z dependence of the light distribution is better fitted by an exponential than by the isothermal sech-squared distribution. The dynamical implication of such a distribution is that the vertical velocity dispersion near the galactic plane should increase with z. A simple model for the light and dust distribution in IC 2531 employing three exponential components is constructed: an old disk, a young disk, and dust. Vertical scale heights of h(zd) = h(z)/4 and h(zy) = h(z)/8 and an absorption equivalent to about half of that in the Galaxy are found to produce the best fits.

Wainscoat, R. J.↗
NASA NTRS1990

Fuselage design for a specified Mach-sliced area distribution

A procedure for designing a fuselage having a prescribed effective area distribution computed from -90 deg Mach slices is described. This type of calculation is an essential tool in designing a complete configuration with an effective area distribution that corresponds to a desired sonic boom signature shape. Sample calculations are given for M=2 and M=3 designs. The examples include fuselages constrained to have circular cross sections and fuselages having cross sections of arbitrary shape. It is found that, for a prescribed effective area distribution having sharp variations, the iterative procedure converges to a smoothed approximation to the prescribed distribution. For a smooth prescribed area distribution, the solution is not unique.

Barger, Raymond L.↗
NASA NTRS1990

Sparse distributed memory overview

The Sparse Distributed Memory (SDM) project is investigating the theory and applications of massively parallel computing architecture, called sparse distributed memory, that will support the storage and retrieval of sensory and motor patterns characteristic of autonomous systems. The immediate objectives of the project are centered in studies of the memory itself and in the use of the memory to solve problems in speech, vision, and robotics. Investigation of methods for encoding sensory data is an important part of the research. Examples of NASA missions that may benefit from this work are Space Station, planetary rovers, and solar exploration. Sparse distributed memory offers promising technology for systems that must learn through experience and be capable of adapting to new circumstances, and for operating any large complex system requiring automatic monitoring and control. Sparse distributed memory is a massively parallel architecture motivated by efforts to understand how the human brain works. Sparse distributed memory is an associative memory, able to retrieve information from cues that only partially match patterns stored in the memory. It is able to store long temporal sequences derived from the behavior of a complex system, such as progressive records of the system's sensory data and correlated records of the system's motor controls.

Raugh, Mike↗
NASA NTRS1990

DSIM: A distributed simulator

Discrete event-driven simulation makes it possible to model a computer system in detail. However, such simulation models can require a significant time to execute. This is especially true when modeling large parallel or distributed systems containing many processors and a complex communication network. One solution is to distribute the simulation over several processors. If enough parallelism is achieved, large simulation models can be efficiently executed. This study proposes a distributed simulator called DSIM which can run on various architectures. A simulated test environment is used to verify and characterize the performance of DSIM. The results of the experiments indicate that speedup is application-dependent and, in DSIM's case, is also dependent on how the simulation model is distributed among the processors. Furthermore, the experiments reveal that the communication overhead of ethernet-based distributed systems makes it difficult to achieve reasonable speedup unless the simulation model is computation bound.

Goswami, Kumar K.↗