Search NASA⌕ Search

SEARCH · Search NASA

Results for “ELECTRON RECOMBINATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Scanning ultrafast electron microscopy reveals photovoltage dynamics at a deeply buried $p^- \mathrm{Si/SiO_2}$ interface

The understanding and control of charge carrier interactions with defects at buried insulator/semiconductor interfaces is essential for achieving optimum performance in modern electronics. In this work, we report on the use of scanning ultrafast electron microscopy (SUEM) to remotely probe the dynamics of excited carriers at a Si surface buried below a thick thermal oxide. Our measurements illustrate a previously unidentified SUEM contrast mechanism, whereby optical modulation of the space-charge field in the semiconductor modulates the electric field in the thick oxide, thus affecting its secondary electron yield. By analyzing the SUEM contrast as a function of time and laser fluence we demonstrate the diffusion mediated capture of excited carriers by interfacial traps.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Energy migration and scintillation kinetics in compositionally complex (Gd 1/4 Y 1/4 Tb 1/4 Lu 1/4 ) 3 Al 5 O 12 :Ce single crystal scintillator

It is well-established that compositional tuning through binary admixture can improve scintillation performance in several materials systems, including Ce-activated garnets. Although recent work on ternary or quaternary cation admixture shows promise, the impact of this increased compositional complexity on thermal stability and carrier-defect dynamics has not been addressed. Here, we investigate a compositionally complex garnet, (Gd 1/4 Y 1/4 Tb 1/4 Lu 1/4 ) 3 Al 5 O 12 :Ce (GYTLAG), grown by the Czochralski method using temperature-dependent photoluminescence (PL), PL decay, and thermoluminescence (TL). PL and PL decay measurements support a thermally activated Tb 3+ -Ce 3+ energy transfer, where Tb 3+ emission dominates below 60 K, but Ce 3+ emission increases from 20-300 K. Thermal quenching of Ce 3+ emission occurs around T 50 = 508 K, with an activation energy of 0.6 eV. TL and wavelength-resolved TL spectra from 20–500 K show that GYTLAG contains similar trap groups to LuAG but with a broader distribution of glow peaks below room temperature, possibly caused by quaternary cation mixing. A combination of dose dependence, partial cleaning and initial rise, and glow curve fitting to a first order continuous Gaussian distribution model are used to understand the contribution of electronic point defects to scintillation decay and afterglow at room temperature. Furthermore, these results inform how increased compositional complexity influences recombination dynamics in garnet scintillators.

Compositionally complex↗
DOE OSTI2022

Controlling Symmetry Breaking Charge Transfer in BODIPY Pairs

Symmetry breaking charge transfer (SBCT) is a process in which a pair of identical chromophores absorb a photon and use its energy to transfer an electron from one chromophore to the other, breaking the symmetry of the chromophore pair. This excited state phenomenon is observed in photosynthetic organisms where it enables efficient formation of separated charges that ultimately catalyze biosynthesis. SBCT has also been proposed as a means for developing photovoltaics and photocatalytic systems that operate with minimal energy loss. It is known that SBCT in both biological and artificial systems is in part made possible by the local environment in which it occurs, which can move to stabilize the asymmetric SBCT state. However, how environmental degrees of freedom act in concert with steric and structural constraints placed on a chromophore pair to dictate its ability to generate long-lived charge pairs via SBCT remain open topics of investigation. In this work we compare a broad series of dipyrrin dimers that are linked by distinct bridging groups to discern how the spatial separation and mutual orientation of linked chromophores and the structural flexibility of their linker each impact SBCT efficiency. Across this material set, we observe a general trend that SBCT is accelerated as the spatial separation between dimer chromophores decreases, consistent with the expectation that the electronic coupling between these units varies exponentially with their separation. However, one key observation is that the rate of charge recombination following SBCT was found to slow with decreasing interchromophore separation, rather than speed up. This stems from an enhancement of the dimers’ structural rigidity due to increasing steric repulsion as the length of their linker shrinks. This rigidity further inhibits charge recombination in systems where symmetry has already enforced zero HOMO-LUMO overlap. Additionally, for the forward transfer the active torsion is shown to increase LUMO-LUMO coupling, allowing for faster SBCT within bridging groups. Further, by understanding trends for how rates of SBCT and charge recombination depend on a dimer’s internal structure and their environment, we identify design guidelines for creating artificial systems for driving sustained light-induced charge separation. Such systems can find application in solar energy technologies and photocatalytic applications but can serve as a model for light-induced charge separation in biological systems.

14 SOLAR ENERGY↗
DOE OSTI2024

Ag Intercalation in Layered Cs 3 Bi 2 Br 9 Perovskite for Enhanced Light Emission with Bound Interlayer Excitons

Cesium bismuth bromide (CBB) has garnered considerable attention as a vacancy-ordered layered perovskite with notable optoelectronic applications. However, its use as a light source has been limited due to its weak photoluminescence (PL). Here, we demonstrate metal intercalation as a novel approach to engineer the room-temperature PL of CBB using experimental and computational methods. Ag, when introduced into CBB, occupies vacant sites in the spacer region, forming octahedral coordination with surrounding Br anions. First-principles density functional theory calculations reveal that intercalated Ag represents the most energetically stable Ag species compared to other potential forms, such as Ag substituting Bi. The intercalated Ag forms a strong polaronic trap state close to the conduction band minimum and quickly captures photoexcited electrons with holes remaining in CBB layers, leading to the formation of a bound interlayer exciton, or BIE. The radiative recombination of this BIE exhibits bright room-temperature PL at 600 nm and a decay time of 38.6 ns, 35 times greater than that of free excitons, originating from the spatial separation of photocarriers by half a unit cell separation distance. The BIE as a new form of interlayer exciton is expected to inspire new research directions for vacancy-ordered perovskites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Modeling dislocation-related leakage currents in GaN p-n diodes

Finite element analysis software was used to model and visualize two p-n junction models: one with a single threading dislocation (TD) and a control model without a dislocation. TDs are modeled as a Gaussian distribution of trap states with an FWHM of 5 nm localized around the r=0 line in a cylindrical coordination such that the linear trap state density was 1 trap/c-translation; this model allows the cylindrical symmetry of the c-plane GaN crystal orientation to be utilized to avoid more computationally intensive 3D models. It was discovered that the interaction of the charged dislocation region with the p-n junction had many notable effects. At zero bias, it was observed that the depletion region width (using the Depletion Approximation) and the maximum electric field were markedly reduced near the dislocation line. More significantly, an asymmetric reduction in the diffusion barrier for electrons (Vbieff=3.03eV) and holes (Vbieff=0.81eV) was observed due to the asymmetric nature of the dislocation band bending related to the doping. The asymmetric reductions in diffusion barriers persisted into VA=2.4V leakage case where asymmetric current profiles for electrons and holes were also observed. Lastly, the diffusion barrier reduction resulted in an additional Shockley-Read-Hall nonradiative recombination leakage caused by a high np-product and trap state density near the intersection of the dislocation with the junction.

Robertson, C. A. (ORCID:0000000300122262)↗
DOE OSTI2023

Investigation of SF6 Alternatives in Spark Gap Switches for GWP Reduction

This primary purpose of this project was to evaluate alternative gas mixtures to sulfur hexafluoride (SF6) developed for high voltage power delivery applications for use in high voltage spark gap switches. These SF6 alternatives lower global warming potential emissions and enable improvements to the pressure-voltage design space. A combined experimental, computational, and theoretical study was used to quantify the impact of persistent breakdown products on the breakdown distribution of SF6-replacement gas mixtures. Viable SF6 replacements suitable for use in spark gap switches were studied to enable performance and agility improvements for next-generation pulsed power research relevant to national security missions. Experimental campaign included establishing parameters of switch gases as function of concentration. Various concentrations and pressures were tested for trends in breakdown voltage, repeatability, and durability, and breakdown constituents. A zero-dimensional plasma global model was used to simulate the plasma arc decay and recombination process in spark-gap switches relevant to the Z machine. Finally, a complete and consistent set of electron-neutral collision cross-sections for the novel insulating gas C4F7N is reported.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Crystalline Si Surface Passivation with Nafion for Bulk Defects Detection with Electron Paramagnetic Resonance

Here, in monocrystalline Si (c-Si) solar cells, identification and mitigation of bulk defects are crucial to achieving a high photoconversion efficiency. To spectroscopically detect defects in the c-Si bulk, it is desirable to passivate the surface defects. Passivation of the c-Si surface with dielectrics such as Al 2 O 3 and SiNx requires deposition at elevated temperatures, which can influence defects in the bulk. Herein, we report on the passivation of different Czochralski (Cz) Si wafer surfaces by an organic copolymer, Nafion. We test the efficacy of the surface passivation at temperatures ranging from 6 to 473 K to detect bulk defects using electron paramagnetic resonance (EPR) spectroscopy. By comparing with state-of-the-art passivation layers, including Al 2 O 3 and liquid HF/HCl, we found that at room temperature, Nafion can provide comparable passivation of n-type Cz Si with an implied open-circuit voltage (iV oc ) of 713 mV and a recombination current prefactor J o of 5 fA/cm 2 . For p-type Cz Si, we obtained an iV oc of 682 mV with a J o of 22.4 fA/cm 2 . Scanning electron microscopy and photoluminescence reveal that Nafion can also be used to passivate the surface of c-Si solar cell fragments scribed from a solar cell module by using a laser. Consistent with previous studies, analysis of the EPR spectroscopy data confirms that the H-terminated surface is necessary, and fixed negative charge in Nafion is responsible for the field-effect passivation. While the surface passivation quality was maintained for almost 24 h, which is sufficient for spectroscopic measurements, the passivation degraded over longer durations, which can be attributed to surface SiO x growth. These results show that Nafion is a promising room-temperature surface passivation technique to study bulk defects in c-Si.

14 SOLAR ENERGY↗
DOE OSTI2020

The influence of lattice defects, recombination, and clustering on thermal transport in single crystal thorium dioxide

Thermal transport is a key controlling property for thorium dioxide in many applications where defect-generating radiation fields are present. An understanding of the effect of nanoscale lattice defects on thermal transport in this material is currently unavailable due to a lack of high-quality, single crystal material from which unit processes may be investigated. In this work, a series of thorium dioxide single crystals are exposed to 2 MeV proton irradiation at room temperature and 600°C to create microscale regions with varying densities and types of point and extended defects. Defected regions are investigated using spatial domain thermoreflectance to quantify the change in thermal conductivity as a function of ion fluence as well as transmission electron microscopy and Raman spectroscopy to interrogate the structure of the generated defects. Together, this com- bination of methods provides important initial insight into defect formation, recombination, and clustering in thorium dioxide and the effect of those defects on thermal transport. These methods also provide a promising pathway for the quantification of the smallest-scale defects which cannot be captured using traditional microscopy techniques and play and outsized role in degrading thermal performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Sputtered indium tin oxide as a recombination layer formed on the tunnel oxide/poly-Si passivating contact enabling the potential of efficient monolithic perovskite/Si tandem solar cells

We focus on utilizing sputtered indium tin oxide (ITO) as a recombination layer, having low junction damage to an n-type silicon solar cell with a front-side tunnel oxide passivating electron contact, thereby enabling the development of a high efficiency monolithic perovskite/Si tandem device. High transparency and low resistivity ITO films are deposited via low power DC magnetron sputtering at room temperature onto a front-side thin SiO x /n + poly-Si contact in a complete Cz n-Si cell with a back-side Al 2 O 3 /SiN x passivating boron-diffused p + -emitter on a random pyramid textured surface. We report the cell characteristics before and after ITO sputtering, and we find a cure at 250 °C in air is highly effective at mitigating any sputtering induced damage. Our ITO coated sample resulted in an implied open-circuit voltage (iV oc ) of 684.7 ± 11.3 mV with the total saturation current density of 49.2 ± 14.8 fA/cm 2 , an implied fill factor (iFF) of 81.9 ± 0.8%, and a contact resistivity in the range of 60 mΩ-cm 2 to 90 mΩ-cm 2 . After formation of a local Ag contact to the rear emitter and sputtered ITO film as the front-side contact without grid fingers, the pseudo-efficiency of 20.2 ± 0.5% was obtained with the V oc of 670.4 ± 7 mV and pseudo FF of 77.3 ± 1.3% under simulated one sun with the calculated short-circuit current density of 30.9 mA/cm 2 from the measured external quantum efficiency. Furthermore, our modelling result shows that efficiency exceeding 25% under one sun is practically achievable in perovskite/Si tandem configuration using the ITO recombination layer connecting a perovskite top cell and a poly-Si bottom cell.

14 SOLAR ENERGY↗
DOE OSTI2025

Unconventional solitonic high-temperature superfluorescence from perovskites

Fast thermal dephasing limits macroscopic quantum phenomena to cryogenic conditions and hinders their use at ambient temperatures. For electronic excitations in condensed media, dephasing is mediated by thermal lattice motion. Therefore, taming the lattice influence is essential for creating collective electronic quantum states at high temperatures. Although there are occasional reports of high-T c quantum effects across different platforms, it is unclear which lattice characteristics and electron–lattice interactions lead to macroscopically coherent electronic states in solids. Here we studied intensity fluctuations in the macroscopic polarization during the emergence of superfluorescence in a lead halide perovskite and showed that spontaneously synchronized polaronic lattice oscillations accompany collective electronic dipole emission. We further developed an effective field model and theoretically confirmed that exciton–lattice interactions lead to a new electronically and structurally entangled coherent extended solitonic state beyond a critical polaron density. The analysis shows a phase transition with two processes happening in tandem: incoherent disordered polaronic lattice deformations establish an order, while macroscopic quantum coherence among excitons simultaneously emerges. Recombination of excitons in this state culminates in superfluorescence at high temperatures. Our study establishes fundamental connections between the transient superfluorescence process observed after the impulsive excitation of perovskites and general equilibrium phase transitions achieved by thermal cooling. By identifying various electron–lattice interactions in the perovskite structure and their respective role in creating collectively coherent electronic effects in solids, our work provides unprecedented insight into the design and development of new materials that exhibit high-temperature macroscopic quantum phenomena.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Tradeoff between Intermolecular Interaction and Backbone Disorder by High Molecular Dipole Block for Improving Blend Morphology of Polymer Solar Cells

Constructing terpolymer has attracted increasing attention as a strategy to improve the performance of polymer solar cell. Terpolymer usually offers an opportunity to lower the frontier molecular orbital energy level, introduces additional absorption band and sometimes optimizes the morphology of the active blend. Generally, the additional segment in terpolymer backbone inevitably introduces backbone disorder, which causes entropy rises. However, selecting a suitable dipole unit introduces extra driving forces for crystallization by enhancing intermolecular interactions. This provides a handy knob for tradeoff between intermolecular interaction and backbone disorder, thus regulating the blend morphology. In this study, a high dipole and electron-deficient group of pyrrolo[3,4-f ]benzotriazole-5,7(6H)-dione (TzBI) is incorporated into the high-performance donor polymer and a series of terpolymers with different content of TzBI are designed. As expected, the morphology is optimized gradually for improving charge generation and charge transport, also suppressing charge recombination. The champion device with 10% TzBI exhibited a power conversion efficiency (PCE) of 18.36%, which is 5% increase compared to the controlled device. This study presents a charming terpolymer strategy by highly electron-deficient and high dipole segment to realize a tradeoff between intermolecular interaction and backbone disorder, facilitating the optimization of morphology and elevation of fill factor and device efficiency.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Silicon nanocluster anion-argon cation recombination via hybrid continuum-molecular dynamics calculations

Prediction of the charge distribution on particles in an aerosol is critical not only in electrical mobility based characterization methods, but also in understanding the role that charging plays in particle growth in gas phase synthesis reactors. The latter is particularly important in non-thermal plasma synthesis reactors, wherein nanoclusters form and grow from vapor phase precursors in a high electron and high ion density environment. In plasmas, because free electrons are much less massive and much more mobile than positive gas ions, nanocluster charge distributions are biased negative. Furthermore, neutral or even positively charged nanoclusters may exist, depending on the rate of nanocluster-gas ion recombination, and nanocluster-nanocluster collisions may greatly contribute to nanocluster growth if not Coulombically suppressed.

42 ENGINEERING↗
DOE OSTI2026

Strain-Driven Evolution of Structural and Carrier Recombination Dynamics in Germanium

Strain engineering in group-IV semiconductors, in particular germanium (Ge), offers a promising route for advancing next-generation optoelectronic device performance. High minority carrier lifetime serves as a direct indicator of superior material quality and device efficiency. Several factors govern the minority carrier lifetime in both strained Ge and strained GeSn, such as strain level, epilayer thickness, defects, surface roughness, and Sn alloying. In this study, the impact of biaxial strain on effective minority carrier lifetimes of tensile-strained Ge (0% ..epsilon..-Ge/Al?As, 0.78% ..epsilon..-Ge/In0.115?Ga0.885?As, and 0.93% ..epsilon..-Ge/In0.16?Ga0.84?As) and compressively strained GeSn (-0.53% c-Ge0.97?Sn0.03/Al?As) epilayers, grown by molecular beam epitaxy, was experimentally investigated via the microwave-reflection photoconductive decay (..mu..-PCD) technique as a simultaneous function of thickness and strain. The structural and strain-relaxation properties were analyzed by high-resolution x-ray diffraction and Raman spectroscopy, while surface morphology analysis using atomic force microscopy provided insights into the surface roughness of strained Ge-based epilayers. Defect characterization by cross-section transmission electron microscopy revealed superior crystalline quality of ..epsilon..-Ge in one epilayer, while twin boundary formation was observed in the other. We investigated the carrier recombination dynamics in epitaxially strained Ge by extracting the bulk recombination lifetime and surface recombination velocity using the thickness-dependent minority carrier lifetime. High effective minority carrier lifetimes of approximately 60-340 ns were achieved at high strain levels with minimal dependence on the thickness of the strained Ge-based epilayers by means of the ..mu..-PCD technique. Minority carrier lifetimes in Ge-based epilayers exhibit a quadratic dependence on the biaxial strain, ranging from -0.88% (compressive) to +1.6% (tensile). The analysis of the carrier recombination dynamics in strained Ge-based heterostructures offers a pathway to designing group-IV based optoelectronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Highly Efficient Ternary Solar Cells with Efficient Förster Resonance Energy Transfer for Simultaneously Enhanced Photovoltaic Parameters

Introducing a third component into organic bulk heterojunction solar cells has become an effective strategy to improve photovoltaic performance. Meanwhile, the rapid development of non-fullerene acceptors (NFAs) has pushed the power conversion efficiency (PCE) of organic solar cells (OSCs) to a higher standard. In this study, a series of fullerene-free ternary solar cells are fabricated based on a wide bandgap acceptor, IDTT-M, together with a wide bandgap donor polymer PM6 and a narrow bandgap NFA Y6. Insights from the morphological and electronic characterizations reveal that IDTT-M has been incorporated into Y6 domains without disrupting its molecular packing and sacrificing its electron mobility and work synergistically with Y6 to regulate the packing pattern of PM6, leading to enhanced hole mobility and suppressed recombination. IDTT-M further functions as an energy-level mediator that increases open-circuit voltage ( V OC ) in ternary devices. In addition, efficient Förster resonance energy transfer (FRET) between IDTT-M and Y6 provides a non-radiative pathway for facilitating exciton dissociation and charge collection. As a result, the optimized ternary device features a significantly improved PCE up to 16.63% with simultaneously enhanced short-circuit current ( J SC ), V OC , and fill factor (FF).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Soft Lattice and Defect Covalency Rationalize Tolerance of β‐CsPbI 3 Perovskite Solar Cells to Native Defects

Abstract Although all‐inorganic metal halide perovskites (MHPs) have shown tremendous improvement, they are still inferior to the hybrid organic–inorganic MHPs in efficiency. Recently, a conceptually new β‐CsPbI 3 perovskite reached 18.4 % efficiency combined with good thermodynamic stability at ambient conditions. We use ab initio non‐adiabatic molecular dynamics to show that native point defects in β‐CsPbI 3 are generally benign for nonradiative charge recombination, regardless of whether they introduce shallow or deep trap states. These results indicate that MHPs do not follow the simple models used to explain defect‐mediated charge recombination in the conventional semiconductors. The strong tolerance is due to the softness of the perovskite lattice, which permits separation of electrons and holes upon defect formation, and only allows carriers to couple to the low‐frequency vibrations. Both factors decrease notably the non‐adiabatic coupling and slow down the dissipation of energy to heat.

Chu, Weibin↗
DOE OSTI2026

Exploring Causes of Beam Loss at CEBAF

At Jefferson Lab, the Continuous Electron Beam Accelerator (CEBAF) features a unique design with two linear accelerators and two arc sections allowing for multiple turns of the electron beam, as well as four experimental end stations. This topology leads to increased beam losses, especially in the spreader and recombiner regions connecting the arcs to the linacs and in the extraction regions connecting the experimental end stations to the accelerator. These losses result in equipment activation and operational interruptions. Recent upgrades to the facility’s diagnostic systems, including the addition of xenon ion chambers, have provided higher-resolution data regarding these loss events. Building on this improved observational capability, we are developing a simulation framework using optics codes and the Geant4-based BDSIM to model beam extinction and halo formation in these regions. This work aims to correlate simulation results with experimental data to isolate the causes of beam loss and inform future machine tuning strategies. We present a summary of conclusions drawn from recent operational studies and outline a plan to model the beam loss and validate the simulations.

Matthews, C. [Old Dominion Univ., Norfolk, VA (Uni↗
DOE OSTI2020

Directly Linking Low-Angle Grain Boundary Misorientation to Device Functionality for GaAs Grown on Flexible Metal Substrates

A new growth method to make highly oriented GaAs thin films on flexible metal substrates has been developed, enabling roll-to-roll manufacturing of flexible semiconductor devices. The grains are oriented in the <001> direction with <1 degree misorientations between them, and they have a comparable mobility to single-crystalline GaAs at high doping concentrations. At the moment, the role of low-angle grain boundaries (LAGBs) on device performance is unknown. A series of electron backscatter diffraction (EBSD) and cathodoluminesence (CL) studies reveal that increased doping concentrations decrease the grain size and increase the LAGB misorientation. Cross-sectional scanning transmission electron microscopy (STEM) reveals the complex dislocation structures within LAGBs. Most importantly, a correlative EBSD/electron beam-induced current (EBIC) experiment reveals that LAGBs are carrier recombination centers and that the magnitude of recombination is dependent on the degree of misorientation. The presented results directly link increased LAGB misorientation to degraded device performance, and therefore, strategies to reduce LAGB misorientations and densities would improve highly oriented semiconductor devices.

36 MATERIALS SCIENCE↗