Search NASA⌕ Search

SEARCH · Search NASA

Results for “ENGINES - INTERCOOLERS - PRESSURE DROP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

In-situ monitoring for liquid metal jetting using a millimeter-wave impedance diagnostic

Abstract This article presents a millimeter-wave diagnostic for the in-situ monitoring of liquid metal jetting additive manufacturing systems. The diagnostic leverages a T-junction waveguide device to monitor impedance changes due to jetted metal droplets in real time. An analytical formulation for the time-domain T-junction operation is presented and supported with a quasi-static full-wave electromagnetic simulation model. The approach is evaluated experimentally with metallic spheres of known diameters ranging from 0.79 to 3.18 mm. It is then demonstrated in a custom drop-on-demand liquid metal jetting system where effective droplet diameters ranging from 0.8 to 1.6 mm are detected. Experimental results demonstrate that this approach can provide information about droplet size, timing, and motion by monitoring a single parameter, the reflection coefficient amplitude at the input port. These results show the promise of the impedance diagnostic as a reliable in-situ characterization method for metal droplets in an advanced manufacturing system.

42 ENGINEERING↗
NASA NTRS2004

Preliminary Analysis of X-Band and Ka-Band Radar for Use in the Detection of Icing Conditions Aloft

NASA and the U.S. Army Cold Regions Research and Engineering Laboratory (CRREL) have an on-going activity to develop remote sensing technologies for the detection and measurement of icing conditions aloft. Radar has been identified as a strong tool for this work. However, since the remote detection of icing conditions with the intent to identify areas of icing hazard is a new and evolving capability, there are no set requirements for radar sensitivity. This work is an initial attempt to quantify, through analysis, the sensitivity requirements for an icing remote sensing radar. The primary radar of interest for cloud measurements is Ka-band, however, since NASA is currently using an X-band unit, this frequency is also examined. Several aspects of radar signal analysis were examined. Cloud reflectivity was calculated for several forms of cloud using two different techniques. The Air Force Geophysical Laboratory (AFGL) cloud models, with different drop spectra represented by a modified gamma distribution, were utilized to examine several categories of cloud formation. Also a fundamental methods approach was used to allow manipulation of the cloud droplet size spectra. And an analytical icing radar simulator was developed to examine the complete radar system response to a configurable multi-layer cloud environment. Also discussed is the NASA vertical pointing X-band radar. The radar and its data system are described, and several summer weather events are reviewed.

Reehorst, Andrew L.↗
NASA NTRSDate not supplied

The Effects of Arcing Ejecta on Space Suit Materials from ISS RPCM Hot Mate/Demate During EVA

Onboard ISS, taking systems off-line when powering down to perform servicing on Remote Power Control Modules (RPCMs) introduces operational risk. An investigation lead by the NASA Engineering and Safety Center (NESC) was performed by a multi-center team to assess the safety of performing on-orbit replacement of RPCMs without powering down. This investigation revealed the potential for molten metal particulate generation in the event of an arcing occurrence. As RPCM replacement can be performed outside ISS during an Extra Vehicular Activity (EVA), it is necessary to assess the effects of this molten metal ejecta contact with the Extravehicular Mobility Unit (EMU) Space Suit Assembly (SSA) during an arcing event. A test was devised to mimic arcing ejecta contact with samples representing various SSA cross-sections. Four areas of the SSA were chosen for test to represent the majority of the SSA cross-sections. Testing was conducted by the University of California, Riverside that generated the molten metal particles, included varying composition, size and temperature, and dropped them onto the surface of the various SSA cross-sections. Exposed SSA materials were then evaluated for degree of damage, penetration, and thermal conductance through the cross-section by ILC Dover. Results showed that the SSA Glove is most susceptible to damage from arcing events. This data will be used to make risk management decisions for future RPCM servicing operations. This testing also demonstrated the durability of the SSA design and materials to exposure to extreme environments

Linda S Hewes↗
NASA NTRSDate not supplied

The Effects of Arcing Ejecta on Space Suit Materials from ISS RPCM Hot Mate/Demate During EVA

Onboard ISS, taking systems off-line when powering down to perform servicing on Remote Power Control Modules (RPCMs) introduces operational risk. An investigation lead by the NASA Engineering and Safety Center (NESC) was performed by a multi-center team to assess the safety of performing on-orbit replacement of RPCMs without powering down. This investigation revealed the potential for molten metal particulate generation in the event of an arcing occurrence. As RPCM replacement can be performed outside ISS during an Extra Vehicular Activity (EVA), it is necessary to assess the effects of this molten metal ejecta contact with the Extravehicular Mobility Unit (EMU) Space Suit Assembly (SSA) during an arcing event. A test was devised to mimic arcing ejecta contact with samples representing various SSA cross-sections. Four areas of the SSA were chosen for test to represent the majority of the SSA cross-sections. Testing was conducted by the University of California, Riverside that generated the molten metal particles, included varying composition, size and temperature, and dropped them onto the surface of the various SSA cross-sections. Exposed SSA materials were then evaluated for degree of damage, penetration, and thermal conductance through the cross-section by ILC Dover. Results showed that the SSA Glove is most susceptible to damage from arcing events. This data will be used to make risk management decisions for future RPCM servicing operations. This testing also demonstrated the durability of the SSA design and materials to exposure to extreme environments.

Linda S. Hewes↗
DOE OSTI2022

Classification of Cloud Particle Imagery from Aircraft Platforms Using Convolutional Neural Networks

Abstract A vast amount of ice crystal imagery exists from a variety of field campaign initiatives that can be utilized for cloud microphysical research. Here, nine convolutional neural networks are used to classify particles into nine regimes on over 10 million images from the Cloud Particle Imager probe, including liquid and frozen states and particles with evidence of riming. A transfer learning approach proves that the Visual Geometry Group (VGG-16) network best classifies imagery with respect to multiple performance metrics. Classification accuracies on a validation dataset reach 97% and surpass traditional automated classification. Furthermore, after initial model training and preprocessing, 10 000 images can be classified in approximately 35 s using 20 central processing unit cores and two graphics processing units, which reaches real-time classification capabilities. Statistical analysis of the classified images indicates that a large portion (57%) of the dataset is unusable, meaning the images are too blurry or represent indistinguishable small fragments. In addition, 19% of the dataset is classified as liquid drops. After removal of fragments, blurry images, and cloud drops, 38% of the remaining ice particles are largely intersecting the image border (≥10% cutoff) and therefore are considered unusable because of the inability to properly classify and dimensionalize. After this filtering, an unprecedented database of 1 560 364 images across all campaigns is available for parameter extraction and bulk statistics on specific particle types in a wide variety of storm systems, which can act to improve the current state of microphysical parameterizations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

TURBO: Terabits/s Using Reconfigurable Bandwidth Optics (Final Report)

Large scale, big science applications are generating petabytes of data that need to be shared among multiple locations. Moving a petabyte of data at 100 Gb/s takes 22 hours. Reducing this to single digit hours or below is clearly attractive and with future applications anticipating exabyte scale transfers, multi-terabit per second capacities are needed. This scale of capacity is available using optical systems. Core optical systems have aggregate per fiber capacities on the order of 10 Tb/s and more than 100 Tb/s system experiments have been realized in the lab. But large optical capacities are not just reserved for the core as similar system capacities are available in metro networks right up to the enterprise, campus, or data center. In general, the same technology is used today in the metro area as in the long-haul networks—reconfigurable optical add drop multiplexing (ROADM) node-based wavelength division multiplexing (WDM) systems. Data centers already support massive internal capacities on the scale of 100’s of Tb/s. As new photonic integrated technologies mature, for example through initiatives such as the Integrated Photonics Innovative Manufacturing Institute (IP-IMI), the cost of optical interfaces is expected to decrease, and higher capacity and higher performance interfaces will become more affordable. This set of circumstances creates the potential that Tb/s capacities will be available at the enterprise and campus level to support large scale science network applications.

42 ENGINEERING↗
DOE OSTI2022

Multichannel haptic feedback unlocks prosthetic hand dexterity

Abstract Loss of tactile sensations is a major roadblock preventing upper limb-absent people from multitasking or using the full dexterity of their prosthetic hands. With current myoelectric prosthetic hands, limb-absent people can only control one grasp function at a time even though modern artificial hands are mechanically capable of individual control of all five digits. In this paper, we investigated whether people could precisely control the grip forces applied to two different objects grasped simultaneously with a dexterous artificial hand. Toward that end, we developed a novel multichannel wearable soft robotic armband to convey artificial sensations of touch to the robotic hand users. Multiple channels of haptic feedback enabled subjects to successfully grasp and transport two objects simultaneously with the dexterous artificial hand without breaking or dropping them, even when their vision of both objects was obstructed. Simultaneous transport of the objects provided a significant time savings to perform the deliveries in comparison to a one-at-a-time approach. This paper demonstrated that subjects were able to integrate multiple channels of haptic feedback into their motor control strategies to perform a complex simultaneous object grasp control task with an artificial limb, which could serve as a paradigm shift in the way prosthetic hands are operated.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

A numerical study of the meso-structure variability in the compaction process of prepreg platelet molded composites

Compaction deformations in a thermoplastic composite system molded from chopped prepreg platelets were analyzed to obtain statistical distributions of local distortions that define the final consolidated meso-structure. This study provides an insight into and allows quantification of the intrinsic geometric variability of the composite meso-structure that controls the variability of the effective composite mechanical properties. A two-phase viscoelastic finite element model was utilized to treat the behavior of molten prepreg platelets, which were assumed to be incompressible and inextensible in the fiber direction during processing. A two-step simulation procedure with discretely modeled platelets and platelet-to-platelet contacts is proposed. The analysis begins with a drop simulation of the uncontrolled material deposition followed by a 3D finite element analysis of the preform compaction and bulk material flow. The proposed model provides a method for generating a composite meso-structure ab initio starting from a statistical sampling of the initial conditions for platelet deposition. The predicted platelet thickness distribution, intra-platelet fiber waviness and out-of-plane platelet undulations were found to be in good agreement with experimental measurements. An estimate of the volume of resin pockets was inferred from the compaction simulation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Unveiling the origins of work-hardening enhancement and mechanical instability in laser shock peened titanium

Laser shock-peening (LSP) produces complex gradients in microstructures and residual stresses, which enables fabrication of metallic engineering components with superior mechanical properties. In this work, we use non-destructive and spatially resolved high-energy X-ray diffraction (HE-XRD) to investigate the influences of LSP on microstructure, surface topography, and residual stress for high purity titanium plates. LSP is found to produce large compressive in-plane residual stresses near the peened surface which monotonically decay to zero about 2.5 mm below the surface. These properties were also tracked during in-situ tensile loading, allowing stress partitioning and work-hardening rates to be measured as a function of depth. The surface region is found to have the highest work-hardening rate and remain mechanically stable up to sample failure. In addition, a crystal rigid rotation along a transversal axis of about 27 & nbsp; was observed at large applied strain near the surface region, which is attributed to the formation of denser dispersed shear bands. Furthermore, a sudden drop in tensile stress was observed at a depth of similar to 160 mu m from the LSP surface, indicating the formation of a localized mechanical instability zone (LMIZ). The origin of this LMIZ could be attributed to the increase in shear stress induced by a load transfer from LSP surface due to the formation of denser dispersed shear bands. These observations indicate a localized transition in deformation behavior has occurred from dispersed shear banding to LMIZ and homogeneous deformation.

36 MATERIALS SCIENCE↗
NASA NTRS2021

Temperature and Frequency Dependent Electrical Properties of AVCOAT and Shuttle Tile Material

This technical memorandum presents the data and results from a series of tests performed on AVCOAT, charred AVCOAT, and different Shuttle Thermal Protection System (TPS) tile coatings to determine their electrical properties as a function of temperature and frequency. Initially, the samples were assumed to be insulators and the complex permittivities were measured from data collected by sandwiching each sample between two conductors to form a sandwich. However, the AVCOAT sample data showed that the material becomes conductive as it begins to char. To get an accurate conductivity reading on these charred samples, a four-point resistance probe was used to collect data. Overall, this testing showed that the virgin AVCOAT starts out as a material that is a good insulator but transitions to one with a conductivity on the order of 1860 S/m as it chars. The deeper layers of AVCOAT (un-charred) all exhibited a temperature and frequency dependence that is possibly indicative of a dielectric relaxation in the material. As the sample temperatures were increased, a knee appears in the real permittivity data sets below 1 kHz. Both the real permittivity and resistivity drop up to several orders of magnitude yet show that the material remains an insulator. The Shuttle High Temperature Reusable Surface Insulation (HRSI) tile coatings studied included Reac- tion Cured Glass (RCG), Aluminum Enhanced Thermal Barrier (AETB), and Toughened Unipiece Fibrous Insulation (TUFI). The purely glass fiber parts of the tile were removed leaving only the outer layers con- taining just the coating. The data collected shows that the RCG, AETB, and outermost layer of the TUFI have similar electrical properties. The real permittivity plots show that there appears to be a relaxation that shows up at frequencies below 1 kHz. The relaxation frequency increases with increasing temperature. Also, the real permittivity increases up to about a factor of four between room temperature and 650K. Likewise, the resistivity (related to the imaginary permittivity) decreases up to five orders of magnitude over the same temperature interval, but still remains an insulator. This data was collected to support a NASA Engineering and Safety Center (NESC) assessment team investigating the source of thermocouple anomalies in both Shuttle TPS material and AVCOAT used for on the Orion spacecraft for Exploration Flight Test 1 (EFT-1). The details of their findings will be documented in a separate report with this document serving as a reference.

Mark A Nurge↗
DOE OSTI2025

Directing the adsorption and assembly of laponite nano-discs at oil–water interfaces

Achieving tunable controls on the adsorption and self-assembly of nanoscale building blocks at immiscible fluid interfaces is essential for synthesizing advanced materials, stabilizing emulsions, and the sustainable storage and recovery of fluids. Although extensive efforts have been directed toward resolving the assembly of spherical nanoparticles at water–hydrocarbon interfaces, 2D nanoparticles have received far less attention. In this study, we developed novel controls to direct the adsorption and assembly of 2D laponite nano-discs (diameter = ∼30 nm and thickness = ∼1 nm) at water–heptane interfaces using traces of sodium dodecyl sulfate (SDS) surfactant, demonstrated by advanced in situ small-angle X-ray scattering, atomic force microscopy, spinning drop tensiometer measurements and molecular dynamics simulations. The results show that SDS surfactant displaces the adsorbed laponite nano-discs from the interface toward the aqueous phase. The extent of this displacement increases with SDS concentration such that high SDS concentrations convert laponite-rich interfaces to SDS-rich interfaces free of laponite nano-discs. This transformation is associated with significant alterations in the rheological and nanomechanical properties of the host interface. In this context, reduction in interfacial tension and interfacial stiffness and an increase in the interfacial deformation is observed on increasing the SDS concentration from 0 to 0.1 wt%. The displacement of laponite nano-discs from the interface is driven by strong electrostatic interactions between the hydrophilic SDS group and interfacial water molecules. These studies unlock new insights into the adsorption and assembly of 2D nanoscale particles at water–hydrocarbons interfaces that are relevant for various applications related to energy and environmental science and engineering.

interfacial tension↗
NASA NTRS2017

Close Range Photogrammetry in Space - Measuring the On-Orbit Clearance between Hardware on the International Space Station

When photogrammetrists read an article entitled "Photogrammetry in Space" they immediately think of terrestrial mapping using satellite imagery. However in the last 19 years the roll of close range photogrammetry in support of the manned space flight program has grown exponentially. Management and engineers have repeatedly entrusted the safety of the vehicles and their crews to the results of photogrammetric analysis. In February 2010, the Node 3 module was attached to the port side Common Berthing Mechanism (CBM) of the International Space Station (ISS). Since this was not the location at which the module was originally designed to be located on the ISS, coolant lines containing liquid ammonia, were installed externally from the US Lab to Node 3 during a spacewalk. During mission preparation I had developed a plan and a set of procedures to have the astronauts acquire stereo imagery of these coolant lines at the conclusion of the spacewalk to enable us to map their as-installed location relative to the rest of the space station. Unfortunately, the actual installation of the coolant lines took longer than expected and in an effort to wrap up the spacewalk on time, the mission director made a real-time call to drop the photography. My efforts to reschedule the photography on a later spacewalk never materialized, so rather than having an as-installed model for the location of coolant lines, the master ISS CAD database continued to display an as-designed model of the coolant lines. Fast forward to the summer of 2015, the ISS program planned to berth a Japanese cargo module to the nadir Common Berthing Mechanism (CBM), immediately adjacent to the Node 3 module. A CAD based clearance analysis revealed a negative four inch clearance between the ammonia lines and a thruster nozzle on the port side of the cargo vehicle. Recognizing that the model of the ammonia line used in the clearance analysis was "as-designed" rather than "as-installed", I was asked to determine the real clearance between the ammonia lines and expected position of the thruster bell using existing on-orbit imagery. Imagery of the area of interest, taken several years earlier from the Space Shuttle during a fly-around of the ISS, was found and used to set a stereo pair. Space Vision System Targets and Handrail bolts measured in the ISS analytical coordinate system (ISSACS) prior to launch, were used to obtain an absolute orientation so all photogrammetric measurement's would be in the ISSACS coordinate system. Coordinates for the design location of the edges of the thruster bell, when the cargo vehicle was fully berthed to the ISS, were displayed in 3-D relative to the as-installed ammonia lines. This immediately revealed a positive clearance, which was later quantified to be a minimum of 10" +/0.5". The analysis was completed over a single weekend by a single analyst. Using updated imagery, acquired from the station's robotic arm, a complete as-installed model of the coolant lines was generated from stereo photography and replaced the design model in the master ISS CAD database.

Liddle, Donn↗
DOE OSTI2026

PACT Center: Perovskite PV Accelerator for Commercializing Technologies (Final Technical Report)

The Perovskite PV Accelerator for Commercializing Technologies (PACT) center was established in July 2021 as a national resource to accelerate the commercialization of perovskite photovoltaic (PV) technology in the United States. Since its inception, PACT has been led by Sandia National Laboratories (Sandia) in partnership with the National Laboratory of the Rockies (NLR), formerly known as NREL. From FY20-FY23, Los Alamos National Laboratory (LANL), CFV Labs, Black & Veatch (B&V), and the Electric Power Research Institute (EPRI) were part of the project team. LANL brought expertise in perovskite PV device designs and processing, CFV Labs (now GroundWork Renewables) provided initial indoor and outdoor measurement hardware technology, B&V led the initial effort on perovskite PV bankability, and EPRI worked on reviewing testing standards, identifying commercialization gaps, and helping to run PACT’s Industry Advisory Board, a group including representatives from commercial testing labs, independent engineering firms, insurance companies, state regulators, and electric utilities. To source perovskite PV module samples, PACT contracted with the University of North Carolina (UNC), the University of Toledo, the University of Washington, and SLAC/Stanford University to provide a steady stream of research-grade perovskite mini modules, enabling protocol development in advance of commercial module availability. The project period ran from July 1, 2021, through December 31, 2025, including a No Cost Extension. Starting in FY25, the project was continued as a Core Capability in the Lab Call portfolio and continues at a reduced budget with only Sandia and NLR as funded recipients. Notably, starting in FY25 PACT expanded its scope beyond MHP modules to accept all emerging PV mini module technologies for testing, including organic PV (OPV) and all-thin-film tandems, with the aim of supporting commercialization across the broader emerging PV ecosystem. With this change in scope the program was renamed the PV Accelerator for Commercializing Technologies, dropping perovskite from the name.

14 SOLAR ENERGY↗
DOE OSTI2024

Performance Assessment of a Dual-purpose HP-TES for a Typical Year Comparing Different Climate Zones

Complete electrification of heating and cooling systems in the United States would overload the existing electrical grid. To this end, recent research efforts have focused on energy storage as one way to reduce ever-increasing peak electricity demands. One such technology is heat pump integrated thermal-energy storage (HP-TES) systems, which can enable load-shifting and reduce demand during peak hours. In this work, a Modelica model of a 4-Ton, dual-mode (heating and cooling) HP-TES system using a room-temperature phase-change material (PCM) integrated through a secondary hydronic loop was developed and simulated for a typical meteorological year in Riverside, CA (ASHRAE Climate Zone 2B), and Chicago, IL (ASHRAE Climate Zone 5A), for a DOE small office prototype building. The COP improvement and demand reduction were analyzed during the time-of-use peak hours along with the required recharge cycle energy demand. A typical summer in Riverside, CA resulted in model-predicted peak COP increases of 50 – 100% compared to the baseline heat pump, especially at higher outdoor temperatures, coupled with maximum peak energy reductions of 22%. During shoulder and winter season simulations, heating energy savings were higher as outdoor temperatures dropped below the PCM phase change temperature. For Chicago, IL, backup heating was necessary to meet the required system capacity for very cold ambient conditions, resulting in winter peak energy savings between 16 – 60% when accounting for backup heating requirements. The recharge energy was found to be mostly below the baseline HP energy during the peak. With improved component selections and controls, the recharge energy may be reduced. The outcomes from the simulations can provide first-order estimates for potential peak energy savings, challenges, and required controls in any location before conducting any field testing.

25 ENERGY STORAGE↗
NASA NTRS2001

Some Recent Observations on the Burning of Isolated N-Heptane and Alcohol Droplets

In a joint program involving Prof. F.A. Williams of the University of California, San Diego and Dr. V. Nayagam of the National Center for Microgravity Research on Combustion and Fluid Dynamics, the combustion of liquid fuel droplets of n-heptane, n-decane, methanol, methanol-water, ethanol and ethanol-water having initial diameters between about 1 mm and 6 mm continues to be studied. The objectives of the work are to improve fundamental knowledge of droplet combustion dynamics for pure fuels and fuel-water mixtures through microgravity experiments and theoretical analyses. The Princeton contributions to the collaborative program supports the engineering design, data analysis, and data interpretation requirements for the study of initially single component, spherically symmetric, isolated droplet combustion studies through experiments and numerical modeling. The complementary UCSD contributions apply asymptotic theoretical analyses and are described in the published literature and in a companion communication in this conference. The combined program continues to focus on analyses of results obtained from Fiber Supported Droplet Combustion (FSDC) experiments (FSDC-2, STS- 94) conducted with the above fuels in shuttle cabin air and Droplet Combustion Experiment (DCE) data obtained for unsupported and fiber supported droplets of n-heptane in Helium-Oxygen mixtures and cabin air (STS-83, STS-94). The program is preparing for a second DCE experimental mission using methanol/methanol-water as fuels and helium-oxygen-nitrogen environments. DCE-2 is to be conducted aboard the International Space Station. Emphases of recent Princeton work are on the study of simple alcohols (methanol, ethanol) and alcohol/water mixtures as fuels, with time-dependent measurements of drop size, flame-standoff, liquid-phase composition, and finally, extinction. Ground based experiments have included bench-scale studies at Princeton and collaborative experimental studies in the 2.2 second drop tower at NASA-Glenn Research Center.

Dryer, F. L.↗
DOE OSTI2022

Sample Preparation and Experimental Design for In Situ Multi-Beam Transmission Electron Microscopy Irradiation Experiments

We discuss the need to understand materials exposed to overlapping extreme environments such as high temperature, radiation, or mechanical stress. When these stressors are combined there may be synergistic effects that enable unique microstructural evolution mechanisms to activate. Understanding of these mechanisms is necessary for the input and refinement of predictive models and critical for engineering of next generation materials. The basic physics and underlying mechanisms require advanced tools to be investigated. The in situ ion irradiation transmission electron microscope (I 3 TEM) is designed to explore these principles. To quantitatively probe the complex dynamic interactions in materials, careful preparation of samples and consideration of experimental design is required. Particular handling or preparation of samples can easily introduce damage or features that obfuscate the measurements. There is no one correct way to prepare a sample; however, many mistakes can be made. The most common errors and things to consider are highlighted within. The I 3 TEM has many adjustable variables and a large potential experimental space, therefore it is best to design experiments with a specific scientific question or questions in mind. Experiments have been performed on large number of sample geometries, material classes, and with many irradiation conditions. The following are a subset of examples that demonstrate unique in situ capabilities utilizing the I 3 TEM. Au nanoparticles prepared by drop casting have been used to investigate the effects of single ion strikes. Au thin films have been used in studies on the effects of multibeam irradiation on microstructure evolution. Zr films have been exposed to irradiation and mechanical tension to examine creep. Ag nanopillars were subjected to simultaneous high temperature, mechanical compression, and ion irradiation to study irradiation induced creep as well. These results impact fields including: structural materials, nuclear energy, energy storage, catalysis, and microelectronics in space environments.

47 OTHER INSTRUMENTATION↗
NASA NTRS1997

Organometallic Polymeric Conductors

For aerospace applications, the use of polymers can result in tremendous weight savings over metals. Suitable polymeric materials for some applications like EMI shielding, spacecraft grounding, and charge dissipation must combine high electrical conductivity with long-term environmental stability, good processability, and good mechanical properties. Recently, other investigators have reported hybrid films made from an electrically conductive polymer combined with insulating polymers. In all of these instances, the films were prepared by infiltrating an insulating polymer with a precursor for a conductive polymer (either polypyrrole or polythiophene), and oxidatively polymerizing the precursor in situ. The resulting composite films have good electrical conductivity, while overcoming the brittleness inherent in most conductive polymers. Many aerospace applications require a combination of properties. Thus, hybrid films made from polyimides or other engineering resins are of primary interest, but only if conductivities on the same order as those obtained with a polystyrene base could be obtained. Hence, a series of experiments was performed to optimize the conductivity of polyimide-based composite films. The polyimide base chosen for this study was Kapton. 3-MethylThiophene (3MT) was used for the conductive phase. Three processing variables were identified for producing these composite films, namely time, temperature, and oxidant concentration for the in situ oxidation. Statistically designed experiments were used to examine the effects of these variables and synergistic/interactive effects among variables on the electrical conductivity and mechanical strength of the films. Multiple linear regression analysis of the tensile data revealed that temperature and time have the greatest effect on maximum stress. The response surface of maximum stress vs. temperature and time (for oxidant concentration at 1.2 M) is shown. Conductivity of the composite films was measured for over 150 days in air at ambient temperature. The conductivity of the films dropped only half an order of magnitude in that time. Films aged under vacuum at ambient temperature diminished slightly in conductivity in the first day, but did not change thereafter. An experimental design approach will be applied to maximize the efficiency of the laboratory effort. The material properties (initial and long term) will also be monitored and assessed. The experimental results will add to the existing database for electrically conductive polymer materials. Attachments: 1) Synthesis Crystal Structure, and Polymerization of 1,2:5,6:9,10-Tribenzo-3,7,11,13-tetradehydro(14) annulene. 2) Reinvestigation of the Photocyclization of 1,4-Phenylene Bis(phenylmaleic anhydride): Preparation and Structure of (5)Helicene 5,6:9,10-Dianhydride. 3) Preparation and Structure Charecterization of a Platinum Catecholate Complex Containing Two 3-Ethynyltheophone Groups. and 4) Rigid-Rod Polymers Based on Noncoplanar 4,4'-Biphenyldiamines: A Review of Polymer Properties vs Configuration of Diamines.

Youngs, Wiley J.↗
DOE OSTI2020

Air evolution during drop impact on liquid pool

We elucidate the evolution of the entrained air in drop impact on a wide range of liquids, using ultrafast X-ray phase-contrast imaging. We elaborate the retraction mechanism of the entrapped air film in terms of liquid viscosity. We found the criterion for deciding if the entrapped air evolves into single or double bubbles, as determined by competition among inertia, capillarity, and viscosity. Low viscosity and low surface tension induce a small daughter droplet encapsulated by a larger air shell bubble, forming an antibubble. We demonstrate a phase diagram for air evolution regarding hydrodynamics.

36 MATERIALS SCIENCE↗