Search NASA⌕ Search

SEARCH · Search NASA

Results for “Exhaust”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Black carbon emissions from modern automated cordwood stoves for space heating

Wood burning stove design is improving as regulation become stricter for particulate matter emissions. Here, this study describes results of black carbon (BC) emissions from three modern automated wood stoves when tested in common failure modes using a test protocol that included cold-starts, high and low fuel loading densities, and use of overly large pieces of fuel. Emission sampling was performed using a dilution sampling system in tandem with an aethalometer to measure BC with high time resolution. Results show that the time-weighted average BC emission rates were 0.91, 4.30, and 1.74 g/h for the three stoves tested (A, B, and C respectively), the values, both higher and lower than the United States 2020 certification test emission limit of 2.5 g/h. The results demonstrate good performance overall, given the rigorous nature of the testing protocol used. The aethalometer data showed that the performance was relatively poor during cold-start, when the fuel was ignited and combusted without a coalbed, and when stoves failed to optimize air delivery due to specific loading and output conditions. During the cold-start test section, the average BC emission rate was seven times higher than the overall average for Stove A, 10 times above the average for Stove B, and two times above the average emission rate for Stove C. Calculations of the Average Angstrom Absorption Exponent (AAE) of the exhaust aerosol showed little correlation with BC concentration. The results show that automation results in a quantifiable reduction in particular BC emissions.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Molecular subtyping reveals immune alterations in IDH wild‐type lower‐grade diffuse glioma

Abstract Isocitrate dehydrogenase ( IDH ) wild‐type diffuse lower‐grade glioma (LGG) is usually associated with poor outcome, but there have been disputes over its clinical outcome and classification. We present here a robust gene expression‐based molecular classification of IDH wild‐type diffuse LGG into two subtypes with distinct biological and clinical features. A discovery cohort of 49 IDH wild‐type diffuse LGGs from the Chinese Glioma Genome Atlas (CGGA) was subjected to clustering and function analysis. Seventy‐three tumors from The Cancer Genome Atlas (TCGA) were used to validate our findings. Consensus clustering of transcriptional data uncovered concordant classification of two robust and prognostically significant subtypes of IDH wild‐type LGG. Subtype 1, associated with poorer outcomes, was characterized by significantly higher immune and cytolytic scores, M2 macrophages, and up‐regulation of immune exhaustion markers, while Subtype 2, which had elevated lymphocytes and plasma cells, showed relatively favorable survival. Somatic alteration analysis revealed that Subtype 1 showed more frequently deleted regions, such as the locus of CDKN2A / CDKN2B , DMRTA1 , C9orf53 , and MTAP . Furthermore, we developed and validated a five‐gene signature for better application of this acquired stratification. Our data demonstrate the biological and prognostic heterogeneity within IDH wild‐type diffuse LGGs and deepen our molecular understandi‐g of this tumor entity. © 2020 Pathological Society of Great Britain and Ireland. Published by John Wiley & Sons, Ltd.

Wu, Fan↗
DOE OSTI2025

Nanofiltration Membranes for Li + /Mg 2+ Separation: Materials and Mechanisms

Nanofiltration (NF) membranes have garnered significant interest for Li + /Mg 2+ separation, a crucial step in lithium extraction from brines. The state-of-the-art commercial LiNE-XD membrane exhibits a Li + /Mg 2+ separation factor (SF Li/Mg ) of 42 at pH 3.3, due to the positive charges on the membrane surface and its strong size-sieving ability. Membranes with higher separation factors at a broad pH range are being pursued to improve separation efficiency. This work aims to provide a timely and comprehensive assessment of advanced NF membranes with superior Li + /Mg 2+ separation properties, as well as their structure and property relationships for designing next-generation membranes. We describe transport mechanisms for ions in NF membranes and discuss governing parameters and models employed to quantify the Li + /Mg 2+ separation. High-performance membrane materials are exhaustively introduced, including commercial and modified polyamides, two-dimensional materials, metal–organic frameworks, crown ethers, and their blends. Finally, we critically compare these membranes in an upper bound plot and highlight the opportunities and challenges of NF membranes for practical Li + /Mg 2+ separations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

On the Search for Low W 0

The magnitude of the vacuum expectation value of the Gukov-Vafa-Witten superpotential |W o | plays a central role in the phenomenology of type IIB flux compactifications. Recent analytical constructions have shown that perturbatively flat vacua can be used to obtain very low values of |W o |. We present systematic algorithms to carry out exhaustive numerical searches for such vacua. Here we also analyse them in the statistical context, as part of the entire ensemble of type IIB flux vacua at low |W o |. Our preliminary analysis indicates that these perturbatively flat vacua are statistically sparse in the whole set of vacua at low |W o | as calculated by Denef and Douglas. Two-moduli examples are used to illustrate these more general findings in specific settings. We find that these simple (two moduli) cases are good examples for existence proofs but they do not feature a large statistical tuning freedom for phenomenological applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

How Atomic Bonding Plays the Hardness Behavior in the Al–Co–Cr–Cu–Fe–Ni High Entropy Family

A systematic study on a face-centered cubic-based compositionally complex alloy system Al–Co–Cr–Cu–Fe–Ni in its single-phase state is carried out, where a mother senary compound Al 8 Co 17 Cr 17 Cu 8 Fe 17 Ni 33 and five of its suballoys, obtained by removing one element at a time, are investigated and exhaustively analyzed determining the contribution of each alloying element in the solid solution. The senary and the quinaries are compared using experimental techniques including X-ray absorption spectroscopy, X-ray diffraction, transmission electron microscopy, and first principles hybrid Monte Carlo/molecular dynamics simulations. Chemical short-range order and bond length distances have been determined both at the experimental and computational level. Electronic structure and local atomic distortions up to 5.2 Å have been correlated to the microhardness values. A linear regression model connecting hardness with local lattice distortions is presented.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Using a Genetic Algorithm to Optimize Configurations in a Data-Driven Application

Users of highly-configurable software systems often want to optimize a particular objective such as improving a functional outcome or increasing system performance. One approach is to use an evolutionary algorithm. However, many applications today are data-driven, meaning they depend on inputs or data which can be complex and varied. Hence, a search needs to be run (and re-run) for all inputs, making optimization a heavy-weight and potentially impractical process. In this paper, we explore this issue on a data-driven highly-configurable scientific application. We build an exhaustive database containing 3,000 configurations and 10,000 inputs, leading to almost 100 million records as our oracle, and then run a genetic algorithm individually on each of the 10,000 inputs. We ask if (1) a genetic algorithm can find configurations to improve functional objectives; (2) whether patterns of best configurations over all input data emerge; and (3) if we can we use sampling to approximate the results. We find that the original (default) configuration is best only 34% of the time, while clear patterns emerge of other best configurations. Out of 3,000 possible configurations, only 112 distinct configurations achieve the optimal result at least once across all 10,000 inputs, suggesting the potential for lighter weight optimization approaches. We show that sampling of the input data finds similar patterns at a lower cost.

Sinha, Urjoshi↗
DOE OSTI2024

Twice upon a time: timelike-separated quantum extremal surfaces

The Python’s Lunch conjecture for the complexity of bulk reconstruction involves two types of nonminimal quantum extremal surfaces (QESs): bulges and throats, which differ by their local properties. The conjecture relies on the connection between bulk spatial geometry and quantum codes: a constricting geometry from bulge to throat encodes the bulk state nonisometrically, and so requires an exponentially complex Grover search to decode. However, thus far, the Python’s Lunch conjecture is only defined for spacetimes where all QESs are spacelike-separated from one another. Here we explicitly construct (time-reflection symmetric) spacetimes featuring both timelike-separated bulges and timelike-separated throats. Interestingly, all our examples also feature a third type of QES, locally resembling a de Sitter bifurcation surface, which we name a bounce. By analyzing the Hessian of generalized entropy at a QES, we argue that this classification into throats, bulges and bounces is exhaustive. We then propose an updated Python’s Lunch conjecture that can accommodate general timelike-separated QESs and bounces. Notably, our proposal suggests that the gravitational analogue of a tensor network is not necessarily the time-reflection symmetric slice, even when one exists.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Revealing the landscape of globally color-dual multi-loop integrands

Abstract We report on progress in understanding how to construct color-dual multi-loop amplitudes. First we identify a cubic theory, semi-abelian Yang-Mills, that unifies many of the color-dual theories studied in the literature, and provides a prescriptive approach for constructingD-dimensional color-dual numerators through one-loop directly from Feynman rules. By a simple weight counting argument, this approach does not further generalize to two-loops. As a first step in understanding the two-loop challenge, we use aD-dimensional color-dual bootstrap to successfully construct globally color-duallocaltwo-loop four-point nonlinear sigma model (NLSM) numerators. The double-copy of these NLSM numerators with themselves, pure Yang-Mills, and$$\mathcal{N}$$= 4 super-Yang-Mills correctly reproduce the known unitarity constructed integrands of special Galileons, Born-Infeld theory, and Dirac-Born-Infeld-Volkov-Akulov theory, respectively. Applying our bootstrap to two-loop four-point pure Yang-Mills, we exhaustively search the space of local numerators and find that it fails to satisfy global color-kinematics duality, completing a search previously initiated in the literature. We pinpoint the failure to the bowtie unitarity cut, and discuss a path forward towards non-local construction of color-dual integrands at generic loop order.

Physics↗
DOE OSTI2023

The Princeton Field-Reversed Configuration for Compact Nuclear Fusion Power Plants

The Princeton Field-Reversed Configuration (PFRC) nuclear fusion reactor concept is an innovative approach to fusion power generation prioritizing low neutron production and small size. Here, a combination of analytical modeling and numerical simulation shows that the novel heating approach generates an FRC with closed field lines. Simulation data from a single-particle Hamiltonian code predicts ms-scale plasma heating in reactor-scale conditions while PIC codes predict formation of warm FRC plasmas from initial mirror fields. The PFRC-1 and PFRC-2 experiments have heated electrons to energies well in excess of 100 eV and plasma durations to 300 ms, more than 10 4 times longer than the predicted tilt instability growth time. From these data, we have created a development plan and anticipated performance metrics for a fusion reactor based on the PFRC concept. The resulting 1–10 MW PFRC reactors would be suitable for diverse applications, from submarines to urban environments to space propulsion. PFRC is a steady-state, driven magnetic confinement device. Plasma, inside a cylindrical array of coils, is confined and heated by external RF antennae. PFRC would be ultra-low radiation due to both its fuel and small size. The choice of advanced fuels, deuterium and helium-3 (D– 3 He), may be enabled by the high-β FRC configuration. The small size of the reactor would enable rapid exhaust of the dangerous tritium ash. Low radiation would make the reactor safer to operate and, in combination with simple geometry and small size, dramatically lowers development and maintenance costs. This review paper gives an introduction to the physics of the PFRC and a summary of the PFRC-2 experiment results to date. It then discusses the future program plan and how PFRC reactors would be commercialized.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

The Oxidation of the HiSiMo Cast Irons Alloyed with Cr/Al at 800 °C

To improve the oxidation resistance of cast iron containing Si and Mo (HiSiMo), 1wt.% Cr and 3wt.% Al were added into the base alloy to improve high temperature oxidation resistance for exhaust manifold applications. Oxidation tests were performed in both dry and wet air (air + 10% H 2 O) at 800 °C for 1, 10, 24, and 50 h. The mass change and oxide thickness were measured to evaluate the oxidation resistance. Scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDS) and transmission electron microscopy (TEM) were employed to characterize the oxidized samples. Here, the results showed that the additions of Al or Cr selectively oxidized to form a more oxidation resistant surface oxide layer, which reduced the mass gain during these experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Accumulative Roll Bonding of Alloy 2205 Duplex Steel and the Accompanying Impacts on Microstructure, Texture, and Mechanical Properties

The mechanical and microstructural evolution of Alloy 2205 during severe plastic deformation is examined in this study. A combination of accumulative roll bonding (ARB) and cold rolling results in the successful formation of a nanograined dual-phase microstructure of austenite and ferrite with some transformed martensite. Severe deformation to cumulative reductions of 80.5, 92.5, 95, and 97 pct were performed. Microscopy indicates that grain dimensions in the sheet normal direction is less than 100 nm for reductions ≥ 92.5 pct. Shear banding is observed at reductions ≥ 95 pct while twinning is only observed at reductions < 92.5 pct. Neutron diffraction measurements indicated the presence of martensite for reductions ≥ 95 pct at ~ 8 pct volume fraction. Taken in conjunction, it appears that during initial ARB processing, both slip and twinning are active plastic mechanisms. As twinning becomes exhausted, martensitic transformation, slip, and intermittent shear banding account for the active plasticity mechanisms. Material hardness saturates at 92.5 pct reduction, with a maximum hardness of 45 HRC. Sub-sized tensile testing confirms this approximate hardness with measurements indicating a UTS of ~ 1440 MPa. Texture analysis of crystal orientation distributions in the plate normal direction suggest an approximate Kurdjumov–Sachs orientation relationship at all reductions above 80 pct indicating stability of the orientation relationship at high strains. The intragranular structure develops a fine scale sub-grain content with increasing deformation, resulting in a continual evolution of texture up to and including 97 pct reduction. The final structure presents strong components of Goss and rotated cube texture in both the austenite and ferrite. In this body of work we aim to compare ARB of an industrially relevant FCC/BCC system (Alloy 2205) to historical model FCC/BCC systems such as Cu/Nb.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The Ductility of 49Fe-49Co-2V Soft Magnetic Alloy Bar: Surface Effects and Test Methods

The tensile ductility of 49Fe-49Co-2V (Hiperco® 50A) bar was investigated in both as-received and heat-treated conditions. The as-received/machined specimens exhibit very low ductility compared to samples where heat treatment was the final step prior to testing. Microstructural characterization showed that internal residual strain from bar processing and, most importantly, surface machining damage, cause lower elongation in the as-received material. Because fracture of this intermetallic alloy initiates at the surface, it is particularly susceptible to surface machining damage, i.e., the near-surface region has already exhausted most of its ability to accumulate tensile strain. During heat treatment, the internal residual strain and near-surface machining damage are eliminated and ductility is improved, despite a higher degree of crystallographic ordering in the heat-treated condition (which typically lowers ductility). Furthermore, if machining is again performed after heat treatment, the material again exhibits brittle behavior, even with only light touch-up machining passes. Here, in this work, methods of tensile strain measurement were investigated, namely conventional knife-edge extensometry and noncontact digital image correlation (DIC) on heat-treated material. For clip-on knife-edge extensometry, the range of failure strain was 2.5-5.5% for heat-treated Hiperco. For noncontact methods, ductility up to 7% was observed. The results highlight the tendency for the alloy to fail at surface imperfections, even those produced by application of the extensometer itself. Noncontact laser extensometry is recommended for determining the intrinsic ductility of the alloy. A method of laser surface modification was developed which increased ductility by ~ 100% compared to unmodified samples. The high cooling rates achieved during laser surface processing can bypass the ordering reaction and produce a ductile disordered structure at the surface that exhibits ductile fracture characteristics.

EBSD↗
DOE OSTI2020

Simulating dispatchable grid services provided by flexible building loads: State of the art and needed building energy modeling improvements

End-use electrical loads in residential and commercial buildings are evolving into flexible and cost-effective resources to improve electric grid reliability, reduce costs, and support increased hosting of distributed renewable generation. This article reviews the simulation of utility services delivered by buildings for the purpose of electric grid operational modeling. We consider services delivered to (1) the high-voltage bulk power system through the coordinated action of many, distributed building loads working together, and (2) targeted support provided to the operation of low-voltage electric distribution grids. Although an exhaustive exploration is not possible, we emphasize the ancillary services and voltage management buildings can provide and summarize the gaps in our ability to simulate them with traditional building energy modeling (BEM) tools, suggesting pathways for future research and development.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Selective Pb 2+ removal and electrochemical regeneration of fresh and recycled FeOOH

Heavy metal pollution is a key environmental problem. Selectively extracting heavy metals could accomplish water purification and resource recycling simultaneously. Adsorption is a promising approach with a facile process, adaptability for the broad concentration of feed water, and high selectivity. However, the adsorption method faces challenges in synthesizing high-performance sorbents and regenerating adsorbents effectively. FeOOH is an environmentally friendly sorbent with low-cost production on a large scale. Nevertheless, the selectivity behavior and regeneration of FeOOH are seldom studied. Therefore, we investigated the selectivity of FeOOH in a mixed solution of Co 2+ , Ni 2+ , and Pb 2+ and proposed to enhance the capacity of FeOOH and regenerate it by using external charges. Without charge, the FeOOH electrode shows a Pb 2+ uptake capacity of 20 mg/g. After applying a voltage of –0.2/+0.8 V, the uptake capacity increases to a maximum of 42 mg/g and the desorption ratio is 70%–80%. In 35 cycles, FeOOH shows a superior selectivity towards Pb 2+ compared with Co 2+ and Ni 2+ , with a purity of 97% ± 3% in the extracts. The high selectivity is attributed to the lower activation energy for Pb 2+ sorption. The capacity retentions at the 5 th and the 35 th cycles are ca. 80% and ca. 50%, respectively, comparable to the chemical regeneration method. With industrially exhausted granular ferric hydroxide as the electrode material, the system exhibits a Pb 2+ uptake capacity of 37.4 mg/g with high selectivity. Our work demonstrates the feasibility of regenerating FeOOH by charge and provides a new approach for recycling and upcycling FeOOH sorbent.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Control of High-Temperature Static and Transient Thermomechanical Behavior of SiMo Ductile Iron by Al Alloying

Abstract Silicon and molybdenum ( SiMo ) ductile iron is commonly used for exhaust manifolds because these components experience thermal cycling in oxidizing environment, which requires resistance to fatigue during transient thermomechanical loads. Previous studies have demonstrated that alloying elements, such as Al , to SiMo ductile iron reduces the amount of surface degradation during static high-temperature exposure. However, deterioration of sphericity of the graphite nodules and a decrease in ductility could affect the tendency of cracking during thermal cycling. In this article, the effect of Al alloying on static and transient thermomechanical behavior of SiMo ductile iron was investigated to optimize the amount of Al alloying. A thermodynamic approach was used to confirm the effect of the Al alloying on the phase transformations in two SiMo cast irons, alloyed by 1.8% Al and 3% Al . These two alloys were cast in a laboratory along with the baseline SiMo ductile iron. Several experimental methods were used to evaluate the dimensional stability, physical properties, static oxidation, and failure resistance during constrained thermal cycling testing to compare their high-temperature capability. Experimental results verified that Al alloying increases the temperature range and decreases volume change during eutectoid transformation, which together with enhancement of oxidation protection improved the dimensional stability. Thermocycling tests showed that the number of cycles to failure depends on the amount of Al alloying and the applied high-temperature exposure during each cycle. SEM/EDX, high-resolution TEM and µCT analysis were used to verify the mechanism resulting from the Al alloying protection. It was shown that an optimal level of Al alloying for balancing oxidation and thermal cracking resistance depends on thermomechanical conditions of application.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Liquid metal walls

Here, the plasma performance of fusion devices depends strongly on the chosen wall materials. Solid plasma-facing components (PFCs) are predominantly used in present devices, and are the most investigated candidates for fusion designs. High-Z materials such as tungsten (W) are the leading solid PFC material candidates. To date, a material choice that scales to steady-state reactor conditions has not been identified. Moreover, if plasma transient events such as edge-localized modes and disruptions cannot be altogether avoided or sufficiently mitigated, the projected peak heat and particle loads far exceed the power exhaust capabilities of solids. Liquid metal (LM) PFCs represent an intrinsic self-healing boundary that are both resilient to surface damage from transients, and that could handle high steady-state heat and particle fluxes. Flowing LM PFCs can be designed to remove “slag,” the buildup of material erosion due to plasma-material interactions, including charge exchange sputtering in the main chamber. Further, LM offer the prospect to manage hydrogenic species otherwise retained in the PFCs, which is important from a safety and inventory standpoint. The two most promising LMs are lithium (Li) and tin (Sn), although Sn–Li eutectics may be considered. While Sn offers a higher temperature window with low vapor pressure and low hydrogen retention, Li offers the prospect of enhanced energy confinement and higher acceptable core contamination limits, and this section focuses on Li PFCs. An LM PFC development research program developed LM PFC concepts for a nuclear fusion device via engineering design calculations, single-effect experiments, and staged prototypical experiments. A self-consistent design window was identified with liquid Li flow speeds ~5–10 m/s; plasma contamination was negligible for predicted Li evolution rates. While these preconceptual designs hold promise, there is substantial R&D needed to advance the technical readiness levels of LM PFCs for application to fusion power plants.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Nuclear fusion powered Titan aircraft

This paper discusses a system for Titan exploration enabled by nuclear fusion power. Titan is one of the most interesting locations in the solar system with a thick atmosphere, surface oceans, under-ice oceans and complex terrain. This paper provides a conceptual design of a fusion-powered system to explore many parts of Titan and enable the use of high-power instruments. The design includes a fusion-powered orbital transfer vehicle and an electric Titan science aircraft. A Direct Fusion Drive (DFD) propulsive engine could bring a sizable spacecraft to Titan orbit in less than two years. A second fusion reactor, configured as a closed-loop power generator, would be used for an electric Titan science aircraft. Both reactors are based on the Princeton Field-Reversed Configuration (PFRC) concept which combines an FRC with a magnetic mirror. PFRC uses a novel radio-frequency plasma heating system and deuterium-helium-3 fuel. A lower temperature plasma flows around the closed-field FRC region removing the fusion products. In the DFD propulsive configuration, this secondary flow permits direct and variable thrust and exhaust velocity. The science aircraft would do a powered entry to Titan and then have the capability to fly anywhere on the moon at subsonic speeds. The DFD-powered transfer vehicle would allow the in-orbit transfer stage to change inclination as needed to cover different areas of the surface.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Microstructure-sensitive mechanical behavior of an additively manufactured psuedoelastic shape memory alloy

The additive manufacturing of shape memory alloys into complex geometries enables fabrication of advanced functional systems across a variety of fields and domains. This work presents results focused on the mechanical behavior of additively manufactured shape memory pseudoelastic NiTi. The deformation induced solid state phase transformation from austenite to martensite allows this system to accommodate large recoverable strains. This deformation behavior is fundamentally driven by crystal-scale transformation physics. Laser powder bed fusion processing reveals that the resulting microstructure, both grain morphology and crystallographic texture, is strongly dependent on the manufacturing processing history. Exhaustive mechanical testing demonstrates that these microstructural factors strongly impact both tensile and cyclic stress–strain behavior. Cyclic dissipative behavior, however, is similar across all tested microstructures following an initial transient period. Remarkably, analysis of spatial strain fields during tensile loading reveals two distinctly different localization “modes”. The first is initiation of localized deformation bands which continuously propagate through the tensile bar during loading. In the second mode localization is observed but lacks propagation; instead additional localization cites nucleate during subsequent loading. The latter phenomena is suspected to be driven by grain-scale deformation physics as the localized band morphologies coincide with grain morphologies. These phenomena strongly impact the resulting aggregate stress–strain behavior. Hence, manufacturers and designers of psuedoelastic functional components must at the very least consider the potential variability in properties when considering additive manufacturing processing. More ideally the process–structure–property relations can be used to further tailor and optimize final functional performance.

Additive manufacturing↗