Search NASA⌕ Search

SEARCH · Search NASA

Results for “FASTENING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Development of the weldbond process for joining titanium

High quality resistance spot welds were produced by welding through epoxy adhesive on titanium alloys. Weldbond joints were consistently stronger than those of either mechanical fasteners, structural adhesive bonds, or mechanical fasteners with adhesive at the joint interface. Weldbond joints and/or spot weld joints showed superior strength at all temperature ranges as compared to other joints tested.

Fields, D.↗

Flight service evaluation of Kevlar-49/epoxy composite panels in wide-bodied commercial transport aircraft

Kevlar-49 fairing panels were inspected and found to be performing satisfactorily after two years flight service on an Eastern and an Air Canada L-1011. Six panels are on each aircraft including sandwich and solid laminate wing-body panels, and 300 F service aft engine fairings. Some of the panels were removed from the aircraft to permit inspection of inner surfaces and fastener hole conditions. Minor defects such as surface cracks due to impact damage, small delaminated areas, elongation and fraying of fastener holes, were noted. None of these defects were considered serious enough to warrant corrective action in the opinion of airline personnel. The defects are typical for the most part of defects noted on similar fiberglass parts.

Stone, R. H.↗

Behavior of composite bolted joints at elevated temperature

Experimental results from an investigation which examines the combined effects of temperature, joint geometry and out-of-plane constraint upon the response of mechanically fastened composite joints are presented. Data are presented for simulated mechanically fastened joint conditions in two laminate configurations fabricated from Hercules AS/3501-6 graphite-epoxy. Strength and failure mode results are presented for the test temperatures of 21 C, 121 C and 177 C and for a range of the geometric parameters W/D and e/D from 3.71 to 7.43 and 1.85 to 3.69, respectively. A hole diameter, D of 5.16 mm was utilized for all tests. Pin bearing tests with out-of-plane constraint were conducted at room temperature only. All elevated temperature data were generated for pin bearing conditions. Ultrasonic C scan inspection of the failed specimens was employed to assess the damage region and to determine failure mode. Comparative data are presented for pin bearing and out-of-plane constraint conditions for the above mentioned joint configurations. The joint under pin loading was modeled by two dimensional finite element methods. Predicted net section strain concentrations were compared with experimental results.

Wilson, D. W.↗

Interaction of laser-induced stress waves with metals

An investigation of the effect of high intensity laser induced stress waves on the hardness and tensile strength of 2024 and 7075 aluminum and on the fatigue properties of 7075 aluminum were investigated. Laser shocking increases the hardness of the underaged 2024-T351 but has little or no effect on the peak aged 2024-T351 and 7075-T651 or the overaged 7075-T73. The fretting fatigue life of fastener joints of 7075-T6 was increased by orders of magnitude by laser shocking the region around the fastener hole; the fatigue crack propagation rates were decreased by laser shocking.

Clauer, A. H.↗

Space fabrication demonstration system

The development effort on the composite beam cap fabricator was completed within cost and close to abbreviated goals. The design and analysis of flight weight primary and secondary beam builder structures proceeded satisfactorily but remains curtailed until further funding is made available to complete the work. The induction fastening effort remains within cost and schedule constraints. Tests of the LARC prototype induction welder is continuing in an instrumented test stand comprised of a Dumore drill press (air over oil feed for variable applied loads) and a dynamometer to measure actual welding loads. Continued testing shows that the interface screening must be well impregnated with resin to ensure proper flow when bonding graphite-acrylic lap shear samples. Specimens prepared from 0.030 inch thick graphite-polyethersulfone are also available for future induction fastening evaluation.

Source record↗

Structural members, method and apparatus

A method and apparatus for fabricating a structural member such as truss from flexible sheet material in compacted form are disclosed. A number of generally tubular columns are progressively formed from the sheet material and deployed generally parallel to one another. Adjacent pairs of the columns are interconnected by respective side members, each of which is comprised of a strip of the sheet material. The sheet material is fastened together by self-attaching fasteners integrally formed from the sheet material of the columns and side members themselves.

Kinzler, J. A.↗

Locking Nut and Bolt

Threaded fastener locks parts securely together despite together large loosening torques, even under conditions of high temperature and vibration. Positive locking action is suitable for use where conventional fasteners tend to work loose--for example, on high-speed rotating machinery. Bolt, nut and key are joined together so key occupies alined slots in bolt and nut and prevents nut from rotating off bolt.

Bishop, R.↗

Improved multilayer insulation applications

Multilayer insulation blankets used for the attenuation of radiant heat transfer in spacecraft are addressed. Typically, blanket effectiveness is degraded by heat leaks in the joints between adjacent blankets and by heat leaks caused by the blanket fastener system. An approach to blanket design based upon modular sub-blankets with distributed seams and upon an associated fastener system that practically eliminates the through-the-blanket conductive path is described. Test results are discussed providing confirmation of the approach. The specific case of the thermal control system for the optical assembly of the Space Telescope is examined.

Mikk, G.↗

Advanced composite aileron for L-1011 transport aircraft: Design and analysis

Detail design of the composite aileron has been completed. The aileron design is a multi-rib configuration with single piece upper and lower covers mechanically fastened to the substructure. Covers, front, spar and ribs are fabricated with graphite/epoxy tape or fabric composite material. The design has a weight savings of 23 percent compared to the aluminum aileron. The composite aileron has 50 percent fewer fasteners and parts than the metal aileron and is predicted to be cost competitive. Structural integrity of the composite aileron was verified by structural analysis and an extensive test program. Static, failsafe, and vibration analyses have been conducted on the composite aileron using finite element models and specialized computer programs for composite material laminates. The fundamental behavior of the composite materials used in the aileron was determined by coupon tests for a variety of environmental conditions. Critical details of the design were interrogated by static and fatigue tests on full-scale subcomponents and subassemblies of the aileron.

Griffin, C. F.↗

Bolt Inserts for Lightning Protection

Stainless steel bolt fasteners have adequate grounding paths for protection of structures against lightning strikes. Fasteners particularly useful in sections where insulating material required, such as thermal panels of external storage tank.

Hambrock, K. O.↗

Strength of Graphite/Metal Composite Lap Joints

Report presents results of tests on fastened lap joints between strips of graphite/aluminum and graphite/magnesium composites. Goal of test program was to establish practical load range and effect of such joint parameters as load direction relative to graphite fiber direction, edge distance, fastener diameters, and lateral spacing as function of net section efficiency.

Ellison, A.↗

Stress analysis method for a clearance fit bolt under bearing loads

In the present, simple analysis method for bolt hole clearance stresses in mechanically fastened joints, an inverse formulation is used with a finite element analysis. Conditions along the bolt hole contact arc are specified by displacement constraint equations. The method was applied to a single fastener clearance-fit joint with typical clearance values, for the cases of a rigid, frictionless bolt and a quasi-isotropic graphite/epoxy laminate. Results indicate that the contact arc, as well as the peak stresses around the hole (and their locations), were strongly influenced by the clearance. After a minor initial nonlinearity, peak stresses varied linearly with applied load. Clearance levels are found to have only a minor influence on overall joint stiffness.

Crews, J. H., Jr.↗

Unitized Nut-and-Washer Assembly

Combination nut, washer, and lockwasher secures parts quickly without damaging metal finishes. Nut and lockwasher are captured by bent tabs of flat washer in this concept for unified fastener. Optional perforated tab on flat washer allows easy tagging and storage. Fastener intended for attaching leads and buses to studs on electronic equipment.

Rossi, P. J.↗

Failure mechanisms of laminates transversely loaded by bolt push-through

Stiffened composite panels proposed for fuselage and wing design utilize a variety of stiffener-to-skin attachment concepts including mechanical fasteners. The attachment concept is an important factor influencing the panel's strength and can govern its performance following local damage. Mechanical fasteners can be an effective method for preventing stiffener-skin separation. One potential failure mode for bolted panels occurs when the bolts pull through the stiffener attachment flange or skin. The resulting loss of support by the skin to the stiffener and by the stiffener to the skin can result in local buckling and subsequent panel collapse. The characteristic failure modes associated with bolt push-through failure are described and the results of a parametric study of the effects that different material systems, boundary conditions, and laminates have on the forces and displacements required to cause damage and bolt pushthrough failure are presented.

Waters, W. A., Jr.↗

Combined bearing and bypass loading on a graphite/epoxy laminate

A combined experimental and analytical study was conducted to determine the behavior of a graphite/epoxy laminate subjected to combined bearing and bypass loading. Single-fastener quasi-isotropic specimens were loaded at various bearing-bypass ratios until damage was produced at the fastener hole. Damage-onset strengths and damage modes were then analyzed using local hole-boundary stresses calculated by a finite-element analysis. The tension data showed the expected linear interaction for combined bearing and bypass loading with damage developing in the net-section tension mode. However, the compression bearing-bypass strengths showed an unexpected interaction involving the bearing mode. Compressive bypass loads reduced the bearing strength by decreasing the bolt-hole contact arc and thus increasing the severity of the bearing loads. The bearing stresses at the hole boundary were not accurately estimated by superposition of the stress components for separate bearing and bypass loading. However, superposition produced reasonably accurate estimates for tangential stresses especially near the specimen net-section.

Crews, J. H., Jr.↗

More Durable Tracks for Heavy Vehicles

Tie bars instead of threaded fasteners make track throwing less likely. Proposed undercarriage for tank or bulldozer has flanged edges to prevent rocks and other road debris from getting caught in track drive and damaging or casting off track. Improved track has no threaded fasteners to be loosened by road shock and vibration. Continuous chain of floating guide bars articulated at web junctions. Pins replace bolted connections. Guide bars and flanges on vehicle keep out stones.

Collins, Earl R., Jr.↗

Spot Paint Sprayer

Proposed atomizing system applies paint to small areas or objects - typically nuts, bolts, or other fasteners on flat surfaces. System used in electronic and mechanical assemblies, where small parts coated but not reached by normal spraying techniques. Coverage expected more complete than that obtained by hand brushing. Paint applicator contains two chambers in which flow of air and atomized paint controlled to ensure complete coating of fastener. In electrostatic version, inner tube serves as one electrode, while object coated serves as other electrode.

Leifsen, J. Arthur↗

Economical Joint for Truss Structures

Mass-produced flat parts easily assembled. Joint for three-dimensional truss made of simple die-cutplates and inexpensive fasteners. Each truss joint consists of two identical interlocking plates bolted, welded, or glued together. Truss struts bolted to joint through holes in plate. Alternatively, ends of struts forked so that they slip over plates and fastened to them by bolts or pins.

Moore, Carleton J.↗