Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fracturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Fracture Network Localization Preceding Catastrophic Failure in Triaxial Compression Experiments on Rocks

We quantify the spatial distribution of fracture networks throughout six in situ X-ray tomography triaxial compression experiments on crystalline rocks at confining stresses of 5–35 MPa in order to quantify how fracture development controls the final macroscopic failure of the rock, a process analogous to those that control geohazards such as earthquakes and landslides. Tracking the proportion of the cumulative volume of fractures with volumes >90th percentile to the total fracture volume, ∑ v 90 / v t o t indicates that the fracture networks tend to increase in localization toward these largest fractures for up to 80% of the applied differential stress. The evolution of this metric also matches the evolution of the Gini coefficient, which measures the deviation of a population from uniformity. These results are consistent with observations of localizing low magnitude seismicity before large earthquakes in southern California. In both this analysis and the present work, phases of delocalization interrupt the general increase in localization preceding catastrophic failure, indicating that delocalization does not necessarily indicate a reduction of seismic hazard. However, the proportion of the maximum fracture volume to the total fracture volume does not increase monotonically. Experiments with higher confining stress tend to experience greater localization. To further quantify localization, we compare the geometry of the largest fractures, with volumes >90th percentile, to the best fit plane through these fractures immediately preceding failure. The r 2 scores and the mean distance of the fractures to the plane indicate greater localization in monzonite than in granite. The smaller mean mineral diameter and lower confining stress in the granite experiments may contribute to this result. Tracking these various metrics of localization reveals a close association between macroscopic yielding and the acceleration of fracture network localization. Near yielding, ∑ v 90 / v t o t and the Gini coefficient increase while the mean distance to the final failure plane decreases. Macroscopic yielding thus occurs when the rate of fracture network localization increases.

58 GEOSCIENCES↗

Permeability and Dispersion Coefficients in Rocks with Fracture Network - 12140

Fluid flow and solute transport are considered for a rock medium with a fracture network with regard to the effective permeability and the dispersion coefficients. To investigate the effects of individual fractures a three-fracture system is chosen in which two are parallel and the third one connects the two at different angles. Specifically the micro-cell boundary-value problems(defined through multiple scale analysis) are solved numerically by using finite elements to calculate the permeability and dispersion coefficients. It is shown that the permeability depends significantly on the pattern of the fracture distribution and the dispersion coefficient is influenced by both the externally imposed pressure gradient (which also reflects the flow field) and the direction of the gradient of solute concentration on the macro-scale. From the calculations of the permeability and dispersion coefficients for solute in a rock medium with a fracture network the following conclusions are drawn. 1. The permeability of fractured medium depends on the primary orientation of the fracture network and is influenced by the connecting fractures in the medium. 2. The cross permeability, e.g., permeability in the direction normal to the direction of the external pressure gradient is rather insensitive to the orientation of the fracture network. 3. Calculation of permeability is most efficiently achieved with optimal discretization across individual fractures and is rather insensitive to the discretization along the fracture.. 4. The longitudinal dispersion coefficient Dxx of a fractured medium depends on both the macro-scale concentration gradient and the direction of the flow (pressure gradient). Hence both features must be considered when investigating solute transport in a fractured medium. (authors)

42 ENGINEERING↗

Role of Mineralogy in Controlling Fracture Formation

The presence of fractures in caprocks can pose increased risks in subsurface energy systems and processes like CO 2 sequestration by introducing high-permeability leakage paths. Fracture apertures and permeability can be altered through mineral dissolution and precipitation reactions, but the reactive evolution of fractures is not well understood. In fractures, minerals that are otherwise inaccessible to reactive fluids can become exposed, resulting in mineral reactions unpredicted by bulk formation data. This work seeks to understand the relationship between mineralogy and fracture formation to enhance our understanding of reactive fracture evolution and CO 2 leakage potential. Here, the mineral compositions of mechanically induced fracture surfaces in samples of the Mancos and Marcellus shales have been quantified and compared to those of the near-fracture matrices using imaging and bulk X-ray diffraction (XRD) data. In the Mancos shale, the concentrations of clay minerals are enhanced along fracture surfaces with respect to the bulk, and the fracture is most likely to form at kaolinite–kaolinite interfaces. Further, evaluation of the mineralogical spatial variability through cross-correlation analysis of the surrounding matrix in images of samples cut perpendicular to the fracture shows that clay is 16.7 times more likely to be present than carbonate minerals near the fracture surface. The high correlation persists roughly 200 μm into the surrounding matrix for the Mancos sample and implies that the fracture formed within a defined clay-rich lithofacies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hydraulic Modeling of Induced and Propagated Fractures: Analysis of Flow and Pressure Data From Hydromechanical Experiments in the COSC-1 Deep Borehole in Crystalline Rock Near Åre, Sweden

To characterize the coupled hydromechanical behavior of rock fractures, the step-rate injection method for fracture in-situ properties (SIMFIP) was conducted with a specialized downhole probe developed by Guglielmi et.al. In June 2019, a field campaign was carried out near Åre, Sweden, where the SIMFIP probe was applied in the Collisional Orogeny in the Scandinavian Caledonides-1 scientific borehole to understand the dynamics of injection-induced fracture initiation, fracture opening, and shearing due to water injection-withdrawal in a borehole interval isolated by two packers. Three intervals were investigated at ~500 m depth: (a) an unfractured section (intact rock), (b) a section with non-conductive fractures, and (c) a section with hydraulically conductive fractures. Pressure, injection flow rate, and borehole wall displacement were simultaneously measured during the tests. In the present study, the geometry of the induced fracture and deformation of existing fractures at different time stages of the tests are determined based on a hydrologic model by using the measured pressure and flow data during each time stage of the experiment. A numerical model for the fluid flow within the fracture and the packed-off borehole interval is implemented within COMSOL Multiphysics. By matching model simulations with observed data for all three sections, estimates of the induced and propagated fractures' radius and aperture at successive time stages have been obtained in each case. We could also determine the non-linear relationship between fracture aperture and pressure for values above fracture opening pressures. The model results provide insights for the understanding of pressure-induced fracture initiation and propagation in crystalline rock.

58 GEOSCIENCES↗

Simulation of Microcapsule Transport in Fractured Media Using Coupled CFD‐DEM

Geothermal energy is sustainable and gaining momentum as a solution to energy crises and environmental issues. However, challenges like production temperature and thermal breakthrough can impact geothermal project efficiency. One innovative solution to alleviate the thermal breakthrough is to inject polymer-based materials that are encapsulated in microcapsules into fractures to modify fracture permeability and prevent preferential flow. In our study, we utilized a coupled computational fluid dynamics and discrete element method to simulate the transport of microcapsules under various scenarios controlled by microcapsule size, microcapsule concentration, and fracture roughness. For a smooth fracture, the results indicate that small microcapsules can travel through a smooth fracture regardless of their concentrations. Large microcapsules can transport through a smooth fracture when present in lower concentrations. However, medium and mixed-size microcapsules tend to cause the sealing of a smooth fracture, irrespective of their concentrations. For a rough fracture, the transport of microcapsules is complicated by their interactions with the rough fracture walls. The presence of two sealing positions in a rough fracture adds further complexity to this transport phenomenon. The size and concentration of microcapsules control one sealing location, while the rough fracture walls determine the other sealing location. The rough walls substantially affect microcapsule transport, rendering the role of microcapsule size and concentration less significant. The simulation results suggest that complex fracture surfaces significantly elevate the occurrence of sealing behavior. To mitigate sealing behavior within more complex fractures, it would be beneficial to use smaller and lower concentrations of microcapsules.

15 GEOTHERMAL ENERGY↗

Experimental Investigation of Low-Frequency Distributed Acoustic Strain-Rate Responses to Propagating Fractures

Summary Low-frequency distributed acoustic sensing (LF-DAS) responds to strain changes due to far-field fracture propagation. To better understand the LF-DAS response to fracture propagation, we performed laboratory-scale hydraulic fracture experiments with embedded optical strain sensors. The objectives of this research are to generate hydraulic fractures of known geometry, measure the strain response along the embedded fiber-optic cable comparable to LF-DAS measurements, and use the results to inform the interpretation of field-derived LF-DAS data. The experiments were conducted in unconfined transparent cubic blocks with a dimension of 8 in. on each side. The block was made of transparent epoxy to visualize the fracture propagation. Fiber-optic sensing cables were embedded in the block at different distances to the source of injection. We injected dyed water through an injection tubing to generate a transverse, radial fracture along an initial flaw. An optical interrogator recorded the response of offset fiber Bragg grating (FBG) strain sensors normal to the plane of the fracture. The strain data were visualized on a waterfall plot, akin to visualizations of field-derived LF-DAS data. Dimensional analysis was used to scale the laboratory results to field conditions. We compared the evolution of the strain response at the fiber-optic cable, injection pressure, and rate with known fracture geometry. The measured strains were compared with Sneddon’s (1946) linear elastic solution for a penny-shaped crack and found to follow this behavior. The generated radial fractures in transparent media can be modeled with Sneddon’s linear elastic radial fracture model and a Mode I critical stress intensity factor. The LF-DAS characteristic response of a narrowing region of extension surrounded by compression was exhibited as a fracture that approached and intersected the fiber-optic cable. The experimentally derived strain and strain-rate waterfall plots with known fracture geometry, injection rate, and pressure response provide insight in understanding LF-DAS responses in the field. Furthermore, we developed a method to estimate fracture geometry evolution from the fiber-optic strain data and validated the method against the experimental data.

Engineering↗

Foam Fracturing Study for Stimulation Development of Enhanced Geothermal Systems

The large thermal gradients and high subsurface temperatures of the western region of the U.S. hold great potential for the implementation of enhanced geothermal systems (EGS). The development of these potential EGS resources requires stimulation of the reservoir to enhance permeability and it has been widely reported that a substantial amount of water will be required should conventional hydraulic stimulation be used. This presents a huge challenge and a high risk to the geothermal development because the water stress1 in these areas is already high or extremely high. The use of foam, a gas/liquid mixture predominantly composed of gas, in fracturing is considered and explored in this project as a potential approach to address water concerns with hydraulic stimulation in the development of EGS. This project, led by Oak Ridge National Laboratory (ORNL) in collaboration with Temple University, was awarded in an open lab call in 2018, and was part of the DOE GTO waterless stimulation initiative. The goal of the project was to demonstrate the feasibility of foam fracturing for EGS development through two primary tasks: Task 1: Laboratory study of the effectiveness of foam fracturing for representative geological materials, including cyclic pressurization using foam (led by ORNL) and Task 2: High temperature foam material selection and characterization (led by Temple University). In FY19, ORNL finished the critical review on serval issues associated with foam fracturing and the implementation of the proposed tasks in a lab study (Wang, et al., 2019), and completed the foam fracturing testing using cement as a model material (Wang, et al, 2020a). The work at ORNL was geared up to develop a brand-new foam testing system in FY20. The purchase of main components for the new system was finished in the first half of the FY20. The assembly of the foam testing system and foam fracturing testing were completed in the second half of the FY20 (Wang, et al., 2021a). Task 1 required the development of a test system which can be used to perform hydraulic fracturing of geological specimens with both water and foamed liquids at pressure up to 6,000 psi (41.4 MPa). The system possesses several capabilities that conventional injection systems lack for hydraulic fracturing. In addition to its ability to generate foam with controlled quality, it is capable of cycling pressure levels between specified values up to frequencies of 50 Hz. The latter capability was developed to evaluate the hypothesis that cyclic loading of samples would produce enhanced fracturing. The system consists of two sections: one for foam generation and another for foam injection. The foam is generated through separate control and pressurization of liquid and gas phases with controlled flow rates. The injection section is equipped with a low-flow Coriolis flow that monitors the density of foam to ensure the injection is in the range of target foam quality2. Experimental results of foam fracturing are reported for cylindrical granite specimens using water and aqueous N2 foam as the fracturing fluids. All experiments were performed for unconfined conditions. The effects of injection mode (i.e., monotonic vs cyclic pressurization) on breakdown pressure and failure response sample were investigated using water alone as a fracturing fluid and foams with a range of compositions. It was found that in the case of monotonic injection, the breakdown pressure of granite specimens tended to be slightly higher when fracturing with foam. Additionally, with a foam quality of 90%, the water use can be reduced by 50 to 84%, depending on hole size. On the other hand, it was observed that the breakdown pressure can be brought down to 70% of the monotonic breakdown pressure by using low cycle fatigue. Finally, discussions are presented regarding injectivity and water use reduction.

15 GEOTHERMAL ENERGY↗

Wellbore Fracture Imaging Using Inflow Detection Measurements

One of the most striking measurements taken during DOE’s EGS Collab project at the 4850-foot depth location was the so-called ‘sewer cam’, which enabled direct visualization of the flow of water into the production well through fractures during the stimulation. The ability to see directly which fractures were flowing and (roughly) how much was a breakthrough in understanding the topology of the created fracture network. Achieving this kind of fracture flow imaging at FORGE would be more challenging because of the 225°C temperature, but equally or even more valuable if it could be achieved. In 2017, a joint project between Sandia and Stanford developed a downhole tool concept to measure the enthalpy of multiphase fluid entering a geothermal well from individual fractures (Gao et al., 2017). For the FORGE project, measuring enthalpy is of less interest because the fluid is expected to be single-phase liquid water. However, the foundation of the device was the measurement of chloride ion concentration, which could form the basis for a direct measurement of inflow from fractures. During the 2017 project, this novel chloride sensing system was implemented into a laboratory test instrument, and we confirmed the capability of the system to measure the ion concentration of fluid entering a model wellbore through a small entry port. The wellbore was a 6-inch diameter model well, and the port was approximately 0.08 inch (2mm) in diameter. The device could measure the chloride concentration accurately even when the well was flowing in a bubbly flow. Given its accuracy, the tool should be able to identify locations of water entering the wellbore even if the ion concentration differs only slightly from that of the water in the well. It is likely that different fractures may flow slightly different chloride concentrations, which would make it feasible to detect individual fractures as well as to estimate the volume of their flow. Ultimately, we could also recognize different fractures flowing back significantly different ion concentrations after fracturing in the FORGE wells. This could be realized by adding different ions in the fracturing fluids in different fractures created at different stages of stimulation (and modifying the tool to include different ion specificity). Sandia’s tool was shown during the study to have the capability to withstand the 225°C temperature, and the electrochemical sensing elements were tested in the laboratory to 225°C at 1500 psia for 24 hours. An early implementation of the fully integrated downhole electrochemical tool, including high-temperature electronics, robust housing, and wireline truck interface, had previously been constructed and tested successfully at Sandia; thus, hardware development tasks focused on advancing the technology readiness level (TRL) of this promising technology for FORGE deployment, rather than on developing a new scientific basis for its operation. The data collection electronics in this tool allowed for several other sensors (pressure, temperature, flow spinner) to be implemented in parallel as well. The research was a new collaboration between Stanford and Sandia to modify and refine the tool for FORGE deployment, to make the downhole measurements, and to characterize the evolving fractures.

15 GEOTHERMAL ENERGY↗

Slip Tendency Analysis of Fracture Networks to Determine Suitability of Candidate Testbeds for the EGS Collab Hydroshear Experiment

Experiment 2 of the EGS Collab project is aimed at testing stimulation by hydro-shearing of existing natural fractures, versus Experiment 1, which is focused on hydraulic fracturing a rock mass to enhance permeability. The main criterion for the testbed selection in Experiment 2 is the presence of an interconnected network of fractures, at least 10 meters in extent, and with orientations such that shear slip can be induced at injection pressures less than the minimum horizontal stress (Shmin). The feasibility analysis for this experiment requires a well-constrained stress state along with well-characterized fracture networks. The fracture systems at two candidate locations in the Sanford Underground Research Facility (SURF), the 4850 Level (number refers to depth below ground surface in feet) and the 4100 Level, have been characterized to different extents. The 4850 Level has a well-characterized Discrete Fracture Network (DFN) from borehole (drilled for an experimental test bed) and drift observations. In contrast, the 4100 level has a fracture network characterized only by observations from the drift wall, which provides little constraint on fracture extents. This paper will present assessments for the interpreted slip potential for the natural fractures at the two locations. Data uncertainties are addressed by performing a probabilistic analysis that takes into account the uncertainty in the stress state, uncertainty in the fracture properties, and preliminary borehole locations. There is strong evidence of shear stimulation of some natural fractures in Experiment 1 on the 4850 level. We use examples of natural fractures strongly linked to shear stimulation in Experiment 1 from multiple monitoring indicators to test the consistency of the stress model and guide the uncertainty interpretation. This analysis is intended to guide the site selection process for Experiment 2 by highlighting the fracture orientations that are likely to be shear-stimulated in a majority of modeled realizations.

15 GEOTHERMAL ENERGY↗

Slip Tendency Analysis of Fracture Networks to Determine Suitability of Candidate Testbeds for the EGS Collab Hydroshear Experiment

Experiment 2 of the EGS Collab project is aimed at testing stimulation by hydro-shearing of existing natural fractures, versus Experiment 1, which is focused on hydraulic fracturing a rock mass to enhance permeability. The main criterion for the testbed selection in Experiment 2 is the presence of an interconnected network of fractures, at least 10 meters in extent, and with orientations such that shear slip can be induced at injection pressures less than the minimum horizontal stress (Shmin). The feasibility analysis for this experiment requires a well-constrained stress state along with well-characterized fracture networks. The fracture systems at two candidate locations in the Sanford Underground Research Facility (SURF), the 4850 Level (number refers to depth below ground surface in feet) and the 4100 Level, have been characterized to different extents. The 4850 Level has a well-characterized Discrete Fracture Network (DFN) from borehole (drilled for an experimental test bed) and drift observations. In contrast, the 4100 level has a fracture network characterized only by observations from the drift wall, which provides little constraint on fracture extents. This paper will present assessments for the interpreted slip potential for the natural fractures at the two locations. Data uncertainties are addressed by performing a probabilistic analysis that takes into account the uncertainty in the stress state, uncertainty in the fracture properties, and preliminary borehole locations. There is strong evidence of shear stimulation of some natural fractures in Experiment 1 on the 4850 level. We use examples of natural fractures strongly linked to shear stimulation in Experiment 1 from multiple monitoring indicators to test the consistency of the stress model and guide the uncertainty interpretation. This analysis is intended to guide the site selection process for Experiment 2 by highlighting the fracture orientations that are likely to be shear-stimulated in a majority of modeled realizations.

40 EE - Geothermal Technologies Office (EE-4G)↗

CT scanning and flow measurements of shale fractures after multiple shearing events

A shearing apparatus was used in conjunction with a Hassler-style core holder to incrementally shear fractured shale cores while maintaining various confining pressures. Computed tomography scans were performed after each shearing event, and were used to obtain information on evolving fracture geometry. Fracture transmissivity was measured after each shearing event to understand the hydrodynamic response to the evolving fracture structure. The digital fracture volumes were used to perform laminar single phase flow simulations (local cubic law with a tapered plate correction model) to qualitatively examine small scale flow path variations within the altered fractures. Fractures were found to generally increase in aperture after several shear slip events, with corresponding transmissivity increases. Lower confining pressure resulted in a fracture more prone to episodic mechanical failure and sudden changes in transmissivity. Conversely, higher confining pressures resulted in a system where, after an initial setting of the fracture surfaces, changes to the fracture geometry and transmissivity occurred gradually. Flow paths within the fractures are largely controlled by the location and evolution of zero aperture locations. Lastly, a reduction in the number of primary flow pathways through the fracture, and an increase in their width, was observed during all shearing tests.

04 OIL SHALES AND TAR SANDS↗

Applications of fractured continuum model to enhanced geothermal system heat extraction problems

This paper describes the applications of the fractured continuum model to the different enhanced geothermal systems reservoir conditions. The capability of the fractured continuum model to generate fracture characteristics expected in enhanced geothermal systems reservoir environments are demonstrated for single and multiple sets of fractures. Fracture characteristics are defined by fracture strike, dip, spacing, and aperture. The paper demonstrates how the fractured continuum model can be extended to represent continuous fractured features, such as long fractures, and the conditions in which the fracture density varies within the different depth intervals. Simulations of heat transport using different fracture settings were compared with regard to their heat extraction effectiveness. The best heat extraction was obtained in the case when fractures were horizontal. A conventional heat extraction scheme with vertical wells was compared to an alternative scheme with horizontal wells. The heat extraction with the horizontal wells was significantly better than with the vertical

Anisotropic permeability↗

Advanced Analysis of Hydraulic Fracture Propagation and Efficiency Using Natural Gas as an Alternative to Water

Over the past years, new technologies have been presented as an alternative to minimize or eliminate the use of water in hydraulic fracturing for unconventional reservoirs, improve resource recovery, cost management and reduce environmental impact. As part of these technologies, energized fluids have been developed to mitigate the environmental impact caused by the application of large volumes of water during hydraulic fracturing. When a fracture is energized, the amount of water pumped during the fracturing process is reduced or eliminated by adding a gas component to the fracturing fluid. The less water that is pumped, the less damage it will create. A new technology called “Energized Natural Gas (ENG)” has recently been proposed for effective hydraulic fracturing in unconventional reservoirs. The ENG process shows that it may be a viable solution for the oil and gas industry. Due to the complexity of multiphase fluid behavior and fracture mechanics, further research and documentation is required to effectively apply gas and gas-water mixtures as a treatment fluid. The objective of this research is to further develop and demonstrate the use of natural gas as an optimum fracturing fluid for tight shale gas formations. GeoMechanics Technologies proposes to complete advanced analyses of hydraulic fracture propagation efficiency using natural gas as an alternative to water. A comprehensive review on the transport properties of gas and water mixtures was performed to investigate the rheology differences of conventionally-used fresh water and the natural gas mixture. This research helped to determine how rheology affects hydraulic fracturing. Then we developed a coupled 3D geomechanical model and fluid flow model to simulate hydraulic fracturing using various mixtures of natural gas and water to determine an effective combination. Gas production was also simulated to further test the effectiveness of the induced fracture. Finally, the technical and economic feasibility of this novel technology was considered and documented.

02 PETROLEUM↗

Simulating the Effect of Fracture Connectivity on Repository Performance with GDSA Framework - 18589

This work examines the possible migration of radionuclides from a deep geologic nuclear waste repository sited in fractured crystalline host rock. The key safety concern is the potential effect on waste isolation of the inter-connectivity of the fracture network, which is primarily established by the temporal evolution of the temperature and stress fields at the time of original rock intrusion and cooling. Two end members are considered in these simulations, one with a high degree of connectivity to the biosphere, such that advective transport through the fracture and fault network controls radionuclide migration, and the other with a low degree of connectivity, such that slow diffusive transport through the crystalline rock matrix is the controlling process for radionuclide migration to the biosphere. Both end members have several areally extensive, high-transmissivity deformation zones, whose distance to the repository is an important factor for waste isolation capability. Uncertainties in fracture properties (transmissivity, orientation, radius) and fracture distribution also give rise to uncertainty in waste isolation capability (i.e., the overall connectivity of the repository with the surface biosphere). These types of natural system uncertainties are generally present in any geologic site-characterization program and thus represent an important factor in assessing repository performance in hard rock environments. The waste considered in these simulations are spent fuel rod assemblies from the U.S. commercial nuclear reactor fleet. Thermal output of the waste must be considered in the simulations and can influence the rate and timing of waste package failure, waste form degradation, and fluid flux due to thermal expansion around the repository horizon. To achieve a high-fidelity representation of radionuclide transport in fractures and rock matrix, combined with thermal energy transport and fluid flow in fractures and matrix, the mathematical model is solved numerically in a parallel high-performance computing (HPC) environment on a finite volume unstructured grid consisting of approximately 5 million cells, using Geologic Disposal Safety Assessment (GDSA) Framework (https://pa.sandia.gov), an open-source performance assessment tool for deep underground disposal of nuclear waste. GDSA Framework uses PFLOTRAN to solve the balance equations on a three-dimensional grid with heterogeneous properties, using multiple processors in a parallel configuration based on domain decomposition. The fracture networks in these simulations are originally generated as discrete fracture networks (DFNs), which are sets of two-dimensional planes distributed in a three-dimensional domain. The method used in GDSA Framework maps the stochastically generated DFN to an equivalent continuous porous medium (ECPM) domain that allows for the simulation of coupled heat flow, fluid flow, and radionuclide transport, including heat conduction through the matrix of the fractured rock, which is a process not easily modeled in a DFN representation. Computational efficiency is also greatly enhanced using the ECPM method, allowing for a realistic representation and analysis of uncertainties in a multi-realization performance assessment of a deep geologic repository. The effect of fracture connectivity on the waste isolation safety function, as brought to light by these GDSA Framework simulations, points to the importance of including a realistic representation of uncertainties in fracture properties and distribution (effectively, uncertainty in spatial heterogeneity) in repository safety assessment simulations. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Are Carotid Stent Fractures Clinically Significant?

Purpose: Late stent fatigue is a known complication after carotid artery stenting (CAS) for cervical carotid occlusive disease. The purpose of this study was to determine the prevalence and clinical significance of carotid stent fractures. Materials and Methods: A single-center retrospective review of 253 carotid bifurcation lesions treated with CAS and mechanical embolic protection from April 2001 to December 2009 was performed. Stent integrity was analyzed by two independent observers using multiplanar cervical plain radiographs with fractures classified into the following types: type I = single strut fracture; type II = multiple strut fractures; type III = transverse fracture; and type IV = transverse fracture with dislocation. Mean follow-up was 32 months. Results: Follow-up imaging was completed on 106 self-expanding nitinol stents (26 closed-cell and 80 open-cell stents). Eight fractures (7.5%) were detected (type I n = 1, type II n = 6, and type III n = 1). Seven fractures were found in open-cell stents (Precise n = 3, ViVEXX n = 2, and Acculink n = 2), and 1 fracture was found in a closed-cell stent (Xact n = 1) (p = 0.67). Only a previous history of external beam neck irradiation was associated with fractures (p = 0.048). No associated clinical sequelae were observed among the patients with fractures, and only 1 patient had an associated significant restenosis ({>=}80%) requiring reintervention. Conclusions: Late stent fatigue after CAS is an uncommon event and rarely clinically relevant. Although cell design does not appear to influence the occurrence of fractures, lesion characteristics may be associated risk factors.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Development of the T+M coupled flow–geomechanical simulator to describe fracture propagation and coupled flow–thermal–geomechanical processes in tight/shale gas systems

We developed a hydraulic fracturing simulator by coupling a flow simulator to a geomechanics code, namely T+M simulator. Modeling of the vertical fracture development involves continuous updating of the boundary conditions and of the data connectivity, based on the finite element method for geomechanics. The T+M simulator can model the initial fracture development during the hydraulic fracturing operations, after which the domain description changes from single continuum to double or multiple continua in order to rigorously model both flow and geomechanics for fracture-rock matrix systems. The T+H simulator provides two-way coupling between fluid-heat flow and geomechanics, accounting for thermoporomechanics, treats nonlinear permeability and geomechanical moduli explicitly, and dynamically tracks changes in the fracture(s) and in the pore volume. We also fully accounts for leak-off in all directions during hydraulic fracturing. We first validate the T+M simulator, matching numerical solutions with the analytical solutions for poromechanical effects, static fractures, and fracture propagations. Then, from numerical simulation of various cases of the planar fracture propagation, shear failure can limit the vertical fracture propagation of tensile failure, because of leak-off into the reservoirs. Slow injection causes more leak-off, compared with fast injection, when the same amount of fluid is injected. Changes in initial total stress and contributions of shear effective stress to tensile failure can also affect formation of the fractured areas, and the geomechanical responses are still well-posed.

02 PETROLEUM↗

Stochastic reconstruction of fracture network pattern using spatial point processes

Fracture spatial patterns can strongly affect fluid flow in the subsurface. Proximity and distribution of fractures control reservoir flow behavior over various length scales. In many studies, however, simplified geometrical patterns are generated for fractures which may lead to unrealistic subsurface models. Here we introduce a new method for characterization and modeling of fracture spatial patterns based on outcrop observations. We use Ripley's K-function to characterize the arrangement of fracture barycenters and intersection points over various length scales. In addition, we use semivariograms to quantify spatial correlation in fracture intensity maps. Using this information, we develop a stochastic algorithm that generates two-dimensional fracture network realizations with spatial properties similar to those of a real fracture network measured in the field. Numerical simulation models indicate that the generated fracture realizations exhibit similar flow behaviors as that of the original fracture network. Furthermore, such modeling tools expand and improve our capability in building representative fracture models and in quantification of uncertainty in naturally and hydraulically fractured reservoirs.

58 GEOSCIENCES↗

Study of seismic diffractions caused by a fracture zone at In Salah carbon dioxide storage project

The In Salah CO 2 storage project in Algeria has injected over 3 million tonnes of carbon dioxide into a water filled tight sand formation. Interferometric Synthetic Aperture Radar (InSAR) range change data revealed a double lobbed pattern of deformation that has been modeled as the opening of a sub-vertical fracture, or damage, zone. The location and geometry of the linear feature were subsequently verified using a seismic reflection survey. The elastic properties of the fracture zone, including anisotropic Poisson ratio ( ν ), Young's ( E ) and shear ( G ) moduli, were estimated from coupled geomechanical and hydrological modeling of surface deformation and pressure variations in the injection well. The elastic moduli reflect the fracture properties after CO 2 flow through the fracture zone. Thus, the seismic signature of the fracture zone could be used for monitoring the CO 2 plume. Using the estimated fracture model, we built two and three dimensional models consisting of an anisotropic fracture zone embedded within an isotropic background. Finite-difference modeling of seismic shot gathers allows us to estimate the effects of scattering from the fracture zone, potentially further constraining the geomechanical model. From the seismic modeling results, we find diffracted waves, induced by the fracture zone, which behave similar to point source diffractions. This modeling is intended to guide a search for diffraction events in the 3D surface seismic field data. The modeling results indicate that using the moduli estimated from geomechanical modeling, fracture scattered events would be 100 times lower amplitude than the interface reflections, and thus would be hard to detect. While diffracted waves are observed in the field data, which may imply the need for revision of the fracture model, including shape and elastic moduli, we are not able to match the field observation with our modeled events. This article presents a frontier study on the integration of geomechanical and geophysical methods at the In Salah site as a means to test the estimate of the subsurface CO 2 flooded fracture properties.

58 GEOSCIENCES↗