SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Low molecular weight liquid polybutadiene polymer flow behavior as function of shear rate, temperature, molecular structure and hydrogen bonding
The thermochemical and flammability properties of thermoplastic and thermoset polymers are discussed. The results of a thermogravimetric analysis of the polymers conducted on a DuPont 950 thermogravimetric analyzer using both nitrogen and air atmospheres are presented. Experimental data on smoke evolution are given, and the methodology for assessing the relative toxicity of the pyrolysis effluents is described. The values obtained from the flammability tests are compared with the stoichiometric char yield, and it is shown that the ignition tendency of the polymers is a linear function of the resin char yield
Positron annihilation rates have been studied in polymers and graphite-polymer composites as a function of their moisture content. The annihilation rates have been found to increase linearly with increasing moisture content in epoxies and polyamides, whereas no definite trends have been observed in polyimides. These experimental results have been used as the basis for the calculation of moisture content of several polymeric test specimens. For example, the directly measured moisture content of a Kevlar specimen was 45.5 + or - 5.0% of saturation value, whereas the moisture content on the basis of the decrease in positron lifetime was calculated to be 46.5 + or - 3.5%. Similarly, the directly measured moisture content of a graphite-epoxy composite (55 v/o fiber) was 19.2 + or - 0.6% of saturation value as opposed to a calculated value of 16.0 + or - 5.0%.
Report presents analysis of experimental data on electrical resistivity of polymer (polyvinyl butyral) as function of temperature and relative humidity. Resulting theoretical expression for electrical resistivity resembles generally accepted empirical law for the corrosion rate.
Two linear polyimides were prepared in various ether and amide solvents. The inherent viscosity was then monitored as a function of time. The polymers made in the ether solvents consistently gave higher inherent viscosities, and thus molecular weights, than the same polymers made in the amide solvents. This molecular weight buildup is attributed to the unique solvation mechanism of the ether solvents which enhances the basicity of the amines via hydrogen bonding.
Films made of certain polymer/carbon composites have been found to be potentially useful as sensing films for detecting airborne elemental mercury at concentrations on the order of tens of parts per billion or more. That is to say, when the polymer/carbon composite films are exposed to air containing mercury vapor, their electrical resistances decrease by measurable amounts. Because airborne mercury is a health hazard, it is desirable to detect it with great sensitivity, especially in enclosed environments in which there is a risk of a mercury leak from lamps or other equipment. The present effort to develop polymerbased mercury-vapor sensors complements the work reported in NASA Tech Briefs Detecting Airborne Mercury by Use of Palladium Chloride (NPO- 44955), Vol. 33, No. 7 (July 2009), page 48 and De tecting Airborne Mer cury by Use of Gold Nanowires (NPO-44787), Vol. 33, No. 7 (July 2009), page 49. Like those previously reported efforts, the present effort is motivated partly by a need to enable operation and/or regeneration of sensors under relatively mild conditions more specifically, at temperatures closer to room temperature than to the elevated temperatures (greater than 100 C ) needed for regeneration of sensors based on noble-metal films. The present polymer/carbon films are made from two polymers, denoted EYN1 and EYN2 (see Figure 1), both of which are derivatives of poly-4-vinyl pyridine with amine functional groups. Composites of these polymers with 10 to 15 weight percent of carbon were prepared and solution-deposited onto the JPL ElectronicNose sensor substrates for testing. Preliminary test results showed that the resulting sensor films gave measurable indications of airborne mercury at concentrations on the order of tens of parts per billion (ppb) or more. The operating temperature range for the sensing films was 28 to 40 C and that the sensor films regenerated spontaneously, without heating above operating temperature (see Figure 2).
The Habitation Systems Development Office (HP40) at NASA Marshall Space Flight Center supports systems engineering, integration, and project management for next generation space habitats. The office is responsible for formulation activities for Lunar Surface Habitat and Mars Transit Habitat. HP40 also manages commercial partnerships for exploration habitat development. The Lunar Surface Habitat is intended to initially support a minimum of two crew on the lunar surface for an approximately 30-day mission, with the ability to accommodate four crew for short durations. The Mars Transit Habitat will transport four crew to and from Mars orbit on a potentially 1,200 day mission. Both concepts are envisioned to leverage inflatable softgoods as the primary structural material for the habitation portion of the architecture. Inflatable softgoods are a complex, multi-material system consisting of multiple layers which perform specific functions. A bladder layer (polymer) contains the habitat’s atmosphere. The bladder is indexed to a woven restraint layer, usually Kevlar or Vectran, which serves as the structural layer. The remaining outer layers are for micro-meteoroid orbital debris (MMOD) shielding, protection from atomic Oxygen (if the material system is to be deployed in low earth orbit), and thermal insulation. The primary advantage of inflatable softgoods is that they can offer a larger volume per unit mass relative to a rigid metal structure. Inflatable softgoods have a strong development heritage within NASA, beginning with work in the 1960s in partnership with Goodyear Aerospace and continuing with Johnson Space Center’s TransHab project in the 1990s . Some development efforts subsequently transitioned into the private sector to mature the material technology for flight applications, including human habitation. In August 2022, NASA published its guidelines for certification of crewed inflatable softgoods structures (JSC-67721). This document outlines a series of tests which will be needed to certify inflatable softgoods material systems for use in crewed mission applications. It includes burst testing at the subscale and full-scale to determine the ultimate burst pressure of the softgoods architecture. Creep (long term deformation of the material under stress) is a key failure mode which must be characterized. Creep testing at the component and module levels is also recommended to generate time to failure curves and verify that the inflatable system has a predicted operational life which exceeds mission parameters. ET (Test Engineering) at MSFC and HP40 have worked together to establish softgoods testing capabilities for the center. This includes the ability to conduct module level burst tests and creep tests. The poster will highlight these capabilities and provide examples of testing which has been performed to date by ET. NASA MSFC anticipates that these test capabilities will continue to offer critical support for companies pursuing inflatable softgoods for exploration applications (lunar surface habitation, Mars transit) as well as commercial low earth orbit platforms.
An anion exchange membrane is composed of a copolymer of 1,1-diphenylethylene and one or more styrene monomers, such as 4-tert-butylstyrene. The copolymer includes a backbone substituted with a plurality of ionic groups coupled to phenyl groups on the backbone via hydrocarbyl tethers between about 1 and about 7 carbons in length. High-temperature conditions enabled by these copolymers enhance conductivity performance, making them particularly suitable for use in anion exchange membranes in fuel cells, electrolyzers employing hydrogen, ion separations, etc. The properties of the membranes can be tuned via the degree of functionalization of the phenyl groups and selection of the functional groups, such as quaternary ammonium groups. Several processes can be used to incorporate the desired ionic functional groups into the polymers, such as chloromethylation, radical bromination, Friedel-Crafts acylation and alkylation, sulfonation followed by amination, or combinations thereof.
An anion exchange membrane is composed of a copolymer of 1,1-diphenylethylene and one or more styrene monomers, such as 4-tert-butylstyrene. The copolymer includes a backbone substituted with a plurality of ionic groups coupled to phenyl groups on the backbone via hydrocarbyl tethers between about 1 and about 7 carbons in length. High-temperature conditions enabled by these copolymers enhance conductivity performance, making them particularly suitable for use in anion exchange membranes in fuel cells, electrolyzers employing hydrogen, ion separations, etc. The properties of the membranes can be tuned via the degree of functionalization of the phenyl groups and selection of the functional groups, such as quaternary ammonium groups. Several processes can be used to incorporate the desired ionic functional groups into the polymers, such as chloromethylation, radical bromination, Friedel-Crafts acylation and alkylation, sulfonation followed by amination, or combinations thereof.
Fuel cells are receiving a considerable amount of attention for potential use in a variety of areas, including the automotive industry, commercial power generation, and personal electronics. Research at the NASA Glenn Research Center has focused on the development of fuel cells for use in aerospace power systems for aircraft, unmanned air vehicles, and space transportation systems. These applications require fuel cells with higher power densities and better durability than what is required for nonaerospace uses. In addition, membrane cost is a concern for any fuel cell application. The most widely used membrane materials for proton exchange membrane (PEM) fuel cells are based on sulfonated perfluorinated polyethers, typically Nafion 117, Flemion, or Aciplex. However, these polymers are costly and do not function well at temperatures above 80 C. At higher temperatures, conventional membrane materials dry out and lose their ability to conduct protons, essential for the operation of the fuel cell. Increasing the operating temperature of PEM fuel cells from 80 to 120 C would significantly increase their power densities and enhance their durability by reducing the susceptibility of the electrode catalysts to carbon monoxide poisoning. Glenn's Polymers Branch has focused on developing new, low-cost membranes that can operate at these higher temperatures. A new series of organically modified siloxane (ORMOSIL) polymers were synthesized for use as membrane materials in a high-temperature PEM fuel cell. These polymers have an organic portion that can allow protons to transport through the polymer film and a cross-linked silica network that gives the polymers dimensional stability. These flexible xerogel polymer films are thermally stable, with decomposition onset as high as 380 C. Two types of proton-conducting ORMOSIL films have been produced: (1) NASA-A, which can coordinate many highly acid inorganic salts that facilitate proton conduction and (2) NASA-B, which has been produced and which incorporates strongly acidic (proton donating) functional groups into the polymer backbone. Both of these polymer films have demonstrated significantly higher proton conductivity than Nafion at elevated temperatures and low relative humidities. An added advantage is that these polymers are very inexpensive to produce because their starting materials are commodity chemicals that are commercially available in large volumes.
Conversion of fluorocarbon dicarboxylic acid to intermediates whose terminal functional groups permit polymerization is discussed. Resulting polymers are used as fuel tank sealers for jet fuels at elevated temperatures. Stability and fuel resistance of the prototype polymers is explained.
Abstract An autofluorescence technique to characterize polymerization progress in real time/in line was developed, which functioned in the absence of typical fluorogenic groups on the monomer or polymer. The monomer dicyclopentadiene and polymer polydicyclopentadiene are hydrocarbons that lack traditional functional groups for fluorescence spectroscopy. Here, the autofluorescence of formulations containing this monomer and polymer during ruthenium‐catalyzed ring‐opening metathesis polymerization (ROMP) was harnessed for reaction monitoring. The methods fluorescence recovery after photobleaching (FRAP) and here‐developed fluorescence lifetime recovery after photobleaching (FLRAP) characterized polymerization progress in these native systems—without requiring exogenous fluorophore. (Auto)fluorescence lifetime recovery changes during polymerization correlated linearly to degree of cure, providing a quantitative link with reaction progress. These changing signals also provided relative rates of background polymerization, enabling comparison of 10 different catalyst‐inhibitor‐stabilized formulations. Multiple‐well analysis demonstrated suitability for future high‐throughput evaluation of formulations for thermosets. The central concept of the combined autofluorescence and FLRAP/FRAP method may be extendable to monitoring other polymerization reactions previously overlooked for lack of an obvious fluorescence handle.
An autofluorescence technique to characterize polymerization progress in real time/in line was developed, which functioned in the absence of typical fluorogenic groups on the monomer or polymer. The monomer dicyclopentadiene and polymer polydicyclopentadiene are hydrocarbons that lack traditional functional groups for fluorescence spectroscopy. Here, the autofluorescence of formulations containing this monomer and polymer during ruthenium-catalyzed ring-opening metathesis polymerization (ROMP) was harnessed for reaction monitoring. The methods fluorescence recovery after photobleaching (FRAP) and here-developed fluorescence lifetime recovery after photobleaching (FLRAP) characterized polymerization progress in these native systems—without requiring exogenous fluorophore. (Auto)fluorescence lifetime recovery changes during polymerization correlated linearly to degree of cure, providing a quantitative link with reaction progress. These changing signals also provided relative rates of background polymerization, enabling comparison of 10 different catalyst–inhibitor-stabilized formulations. Multiple-well analysis demonstrated suitability for future high-throughput evaluation of formulations for thermosets. Furthermore, the central concept of the combined autofluorescence and FLRAP/FRAP method may be extendable to monitoring other polymerization reactions previously overlooked for lack of an obvious fluorescence handle.
Regardless of their applications, polymers are still considered mechanically weak and functionally insufficient for certain demanding coating and adhesive uses. To address those issues, nanomaterials have been extensively studied as reinforcing fillers, which have been proven to effectively promote the performance of polymer coatings/adhesives. However, conventional nanofillers are expensive and non-biodegradable. Meanwhile, cellulose nanomaterials (CNMs), a class of nanomaterials produced from biomass feedstocks, can circumvent the drawbacks of conventional nanofillers. Here, this review paper first focuses on the multi-functionalities CNMs bring to polymer coatings, including mechanical reinforcement (wear resistance and hardness enhancement), gas barrier, flame resistance, corrosion resistance, self-healing (controlled-release), optical regulation, self-cleaning/antifouling, and antimicrobial characteristics. Then we discuss the benefits of CNM addition to polymer adhesives, such as mechanical enhancement, curing promotion, volatile organic compound (VOC) suppression, and electrical conductivity. Finally, we provide insights into future research efforts with CNMs. The goal of this paper is to promote the pilot-scale study and commercial use of CNMs as multifunctional additives in green and sustainable polymer composite coating and adhesive formulations.
Abstract Surface grafting of polymer brushes drastically modifies surface properties, including wettability, compatibility, responsiveness, etc. A broad variety of functionalities can be introduced to the surface via different types of polymers. Bringing together properties of two or more types of polymer brushes to one surface opens up even more possibilities in brush‐modified materials. However, while it is generally feasible to introduce several chemical compositions along the brushes via copolymerization, it is challenging to vary the types of polymer brushes along a surface. Although previous studies have demonstrated binary brushes via orthogonal polymerization techniques or partial deactivation/regrafting, they commonly limit the number of polymer types to two. Here, we propose a strategy to introduce dynamic covalent diketoenamine linkages at the root of polymer brushes. The grafting density could be precisely tuned during surface functionalization. The surface‐anchored polymer brushes were cleaved by the addition of small molecule amines. New polymer brushes can be regrafted from the surface following refunctionalization of exposed sites. The maneuverability allows tuning of the types and densities of the polymer brushes, pointing the way to the preparation of a new generation of well‐defined brush‐modified materials with mixed grafts, with potential applications in the design of smart materials and surfaces.
A polymer fiber-based adsorbent (AF1) composed of acrylonitrile and itaconic acid functional groups was synthesized by a radiation-induced graft polymerization technique onto hollow-gear shaped polyethylene (PE) fibers. Investigation of the optimum reaction parameters for the conversion of grafted cyano moieties into amidoxime groups was conducted by the reaction with hydroxylamine at different temperatures and periods in a variety of aqueous and organic solvents. The 13 C CP/MAS spectra of amidoximated AF1 adsorbent fibers from water–methanol and dimethyl sulfoxide (DMSO) revealed that both the cyclic imide dioxime and open-chain amidoxime were formed through the reaction. The conversion from amidoxime to imide dioxime was found to occur slowly and gradually with the increasing reaction time. The quicker diffusion of DMSO as compared to that of water–methanol, in the grafted trunk PE fiber, resulted in faster kinetics of the amidoximation reaction. The uranium adsorption capacity of the amidoximated AF1 samples was determined after (i) 24 h contact with sodium-based brine spiked with uranium and (ii) 56 days of exposure to filtered seawater (Sequim Bay, WA, USA) in flow-through columns. Finally, the uranium extraction performance of the adsorbents after exposure to filtered seawater was consistent with the laboratory screening results, and the amidoximated AF1 samples (in DMSO at 70 °C for 3 h) exhibited the highest 56 day uranium adsorption capacity (5.04 ± 0.15 g U/kg-ads) with faster adsorption kinetics compared to the pristine AF1 adsorbents.
Nature abounds with intricate composite architectures composed of hard and soft materials synergistically intertwined to provide both useful functionality and mechanical integrity. Recent synthetic efforts to mimic such natural designs have focused on nanocomposites, prepared mainly by slow procedures like monomer or polymer infiltration of inorganic nanostructures or sequential deposition. Here we report the self-assembly of conjugated polymer/silica nanocomposite films with hexagonal, cubic or lamellar mesoscopic order using polymerizable amphiphilic diacetylene molecules as both structure-directing agents and monomers. The self-assembly procedure is rapid and incorporates the organic monomers uniformly within a highly ordered, inorganic environment. Polymerization results in polydiacetylene/silica nanocomposites that are optically transparent and mechanically robust. Compared to ordered diacetylene-containing films prepared as Langmuir monolayers or by Langmuir-Blodgett deposition, the nanostructured inorganic host alters the diacetylene polymerization behaviour, and the resulting nanocomposite exhibits unusual chromatic changes in response to thermal, mechanical and chemical stimuli. The inorganic framework serves to protect, stabilize, and orient the polymer, and to mediate its function. The nanocomposite architecture also provides sufficient mechanical integrity to enable integration into devices and microsystems.
Abstract Self‐doping ionene polymers were efficiently synthesized by reacting functional naphthalene diimide (NDI) with 1,3‐dibromopropane ( NDI‐NI ) or trans ‐1,4‐dibromo‐2‐butene ( NDI‐CI ) via quaternization polymerization. These NDI‐based ionene polymers are universal interlayers with random molecular orientation, boosting the efficiencies of fullerene‐based, non‐fullerene‐based, and ternary organic solar cells (OSCs) over a wide range of interlayer thicknesses, with a maximum efficiency of 16.9 %. NDI‐NI showed a higher interfacial dipole (Δ), conductivity, and electron mobility than NDI‐CI , affording solar cells with higher efficiencies. These polymers proved to efficiently lower the work function ( WF ) of air‐stable metals and optimize the contact between metal electrode and organic semiconductor, highlighting their power to overcome energy barriers of electron injection and extraction processes for efficient organic electronics.