Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ground Demonstration Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Satellite power system (SPS) concept definition study. Volume 3: Experimental verification definition

An evolutionary Satellite Power Systems development plan was prepared. Planning analysis was directed toward the evolution of a scenario that met the stated objectives, was technically possible and economically attractive, and took into account constraining considerations, such as requirements for very large scale end-to-end demonstration in a compressed time frame, the relative cost/technical merits of ground testing versus space testing, and the need for large mass flow capability to low Earth orbit and geosynchronous orbit at reasonable cost per pound.

Hanley, G. M.↗
NASA NTRS1980

SPS technical issues

The technical issues which would either seriously impact or potentially negate the integrity of a solar power satellite program are enumerated. Issues are identified not only relating to the question of engineering feasibility, but also to the equally important areas of environmental and social acceptability and, especially, economic viability. Specific information required for resolution of the issues was developed and a planned overall approach for resolution was identified. Results of these analyses show that 60% of the technical issues can be resolved with analysis only; 10% require only ground testing for resolution; and the remaining 30% require space experiments or demonstrations for resolution. The results also show that 85% resolution of the issues may be accomplished prior to development of a protoype.

Guttman, C. H.↗
NASA NTRS1988

Requirements and an approach for coating the Gravity Probe B gyroscope rotor

A process to coat a quartz gyroscope rotor uniformly with superconducting niobium as part of a NASA sponsored experiment to test general relativity is described. The requirements for uniformity, film adhesion, and superconducting properties of the niobium thin film rotor coating are discussed. A uniformity of 1.5 percent (peak to valley) (38 nm) with good adhesion, no pinholes larger than 0.25 mm, transition temperature of 9.8 K, and the ability to survive repeated thermal cycling to 4.2 K have been achieved. Problems concerning abrasive damage and electrical arc damage during earthbound testing have been observed. Many hours of ground-based gyro operation demonstrate the applicability of this approach to rotor coating.

Gill, D.↗
NASA NTRS1998

X-34 Experimental Aeroheating at Mach 6 and 10

Critical technologies are being developed to support the goals of the NASA Office of Aeronautics and Space Transportation Technology Access to Space initiative for next-generation reusable space transportation systems. From the perspective of aerothermodynamic performance throughout the flight trajectory, the Reusable Launch Vehicle program incorporates conceptual analysis, ground-based testing, and computational fluid dynamics to provide flyable suborbital flight demonstrator vehicles. This report provides an overview of the hypersonic aeroheating wind tunnel test program conducted at the NASA Langley Research Center in support of one of these vehicles, the X-34 small reusable technology demonstrator program. Global surface heat transfer images, surface streamline patterns, and shock shapes were measured on 0.0153- and 0.0183-scale models of proposed X-34 flight vehicles at Mach 6 and 10 in air. The primary parametrics that were investigated include angles-of-attack from 0 to 35 deg. and freestream unit Reynolds numbers from 0.5 to 8 million per foot (which was sufficient to produce laminar, transitional, and turbulent heating data), both with and without control surface deflections. Comparisons of the experimental data to computational predictions are included, along with a discussion of the implications of some of the experimental flow features for the flight vehicle.

Berry, Scott A.↗
NASA NTRS1996

Preliminary Results, Analysis and Overview of Part -1 of the GOLD Experiment

The Ground/Orbiter Lasercomm Demonstration (GOLD) is an optical communications demonstration between Japanese Engineering Test Satellite (ETS-V1) and an optical ground transmitting and receiving station at the Table Mountain Facility in Wrightwood California. Laser transmissions to the satellite were performed approximately four hours every third night when the satellite was at above Table Mountain.

GOLD ETS-V1 Table Mountain Facility optical commun↗
NASA NTRS2008

Cryogenic Fluid Transfer for Exploration

This paper discusses current plans and issues for exploration that involve the use of cryogenic transfer. The benefits of cryogenic transfer to exploration missions are examined. The current state of the art of transfer technology is reviewed. Mission concepts of operation for exploration are presented, and used to qualitatively discuss the performance benefits of transfer. The paper looks at the challenges faced to implement a cryogenic transfer system and suggest approaches to address them with advanced development research. Transfer rates required for exploration are shown to have already been achieved in ground test. Cost-effective approaches to the required on-orbit demonstration are suggested.

Chato, David J.↗
NASA NTRS2016

Rocket Propulsion (RP) 21 Steering Committee Meeting - NASA Spacecraft Propulsion Update

Lander Tech is three separate but synergistic efforts: Lunar CATALYST (Lunar Cargo Transportation and Landing by Soft Touchdown) Support U.S. industry led robotic lunar lander development via three public-private efforts. Support U.S. industry led robotic lunar lander development via three public-private partnerships. Infuse or transfer landing technologies into these public private partnerships. Advanced Exploration Systems-Automated Propellant Loading (APL) -Integrated Ground Operations. Demonstrate LH2 zero loss storage, loading and transfer operations via testing on a large scale in a relevant launch vehicle servicing environment. (KSC, GRC). Game Changing Technology-20 Kelvin -20 Watt Cryocooler Development of a Reverse Turbo-Brayton Cryocooler operating at 20 Kelvin with 20 Watts of refrigeration lift.

Propellant↗
NASA NTRSDate not supplied

Obtaining Public Opinion about sUAS Activity in an Urban Environment

The Unmanned Aircraft Systems (UAS) Traffic Management (UTM) research project has been developing and testing concept ideas for enabling small UAS (sUAS) operations in low altitude airspace (ground to 400 feet). To do this, a series of flight test demonstrations were organized over five years at seven test sites. Technology Capability Level-4 (TCL4), the most complex flight tests, were conducted in Texas, USA, during August 2019. This testing resulted in over 400 data collection flights using eight live rotorcraft, with nine flight crews flying pre-planned scenarios in the urban downtown and waterfront areas of Corpus Christi, Texas. Test scenarios were designed to include a variety of elements, including live and simulated vehicles, and personnel in many different roles, including flight crews and mission personnel. One group of people who did not have a role in the flight tests but will be affected by UAS operations as they become more ubiquitous, are the general public. What do the public think about sUAS operations in urban areas? In order to obtain a reference point that noted the public's view of the operations in the TCL4 demonstration, a short survey was developed and offered to members of the public who wished to comment on the sUAS activities they saw in their city during two weeks in August, 2019.Forty five people completed the online public opinion survey. Participants volunteered to take it, creating a self-selected sample. The survey included eleven questions that asked participants about their level of comfort and concerns with UAS activity; their knowledge of UAS operations; and, whether a traffic management system like UTM would increase their confidence in urban UAS activity. The general public in Corpus Christi showed a good level of knowledge of sUAS regulations, with almost half of their responses to the knowledge portion of the survey being correct. They expressed a moderate level of concern (x = 4.7 out of 7) at urban sUAS activity and, of those who cited a concern, the majority reported this was about privacy (54%), which are all responses in line with those reported in earlier research on public opinion. Views on UTM were mixed, with respondents indicating they thought the introduction of UTM will improve safety somewhat (5.2 out of 7) but it will also increase their concern a little (4.6 out of 7). This would indicate there needs to be more information and educational material about the UTM concept made available to the public with the aim to reduce public concerns about the system.

Caterina Grossi↗
NASA NTRSDate not supplied

Obtaining Public Opinion About sUAS Activity in an Urban Environment

The Unmanned Aircraft Systems (UAS) Traffic Management (UTM) research project has been developing and testing concept ideas for enabling small UAS (sUAS) operations in low altitude airspace (ground to 400 feet). To do this, a series of flight test demonstrations were organized over five years at seven test sites. Technology Capability Level-4 (TCL4), the most complex flight tests, were conducted in Texas, USA, during August 2019. This testing resulted in over 400 data collection flights using eight live rotorcraft, with nine flight crews flying pre-planned scenarios in the urban downtown and waterfront areas of Corpus Christi, Texas. Test scenarios were designed to include a variety of elements, including live and simulated vehicles, and personnel in many different roles, including flight crews and mission personnel. One group of people who did not have a role in the flight tests but will be affected by UAS operations as they become more ubiquitous, are the general public. What do the public think about sUAS operations in urban areas? In order to obtain a reference point that noted the public’s view of the operations in the TCL4 demonstration, a short survey was developed and offered to members of the public who wished to comment on the sUAS activities they saw in their city during two weeks in August, 2019. Forty five people completed the online public opinion survey. Participants volunteered to take it, creating a self-selected sample. The survey included eleven questions that asked participants about their level of comfort and concerns with UAS activity; their knowledge of UAS operations; and, whether a traffic management system like UTM would increase their confidence in urban UAS activity. The general public in Corpus Christi showed a good level of knowledge of sUAS regulations, with almost half of their responses to the knowledge portion of the survey being correct. They expressed a moderate level of concern (x = 4.7 out of 7) at urban sUAS activity and, of those who cited a concern, the majority reported this was about privacy (54%), which are all responses in line with those reported in earlier research on public opinion. Views on UTM were mixed, with respondents indicating they thought the introduction of UTM will improve safety somewhat (5.2 out of 7) but it will also increase their concern a little (4.6 out of 7). This would indicate there needs to be more information and educational material about the UTM concept made available to the public with the aim to reduce public concerns about the system.

UTM↗
NASA NTRS2010

Modeling and Performance Considerations for Automated Fault Isolation in Complex Systems

The purpose of this paper is to document the modeling considerations and performance metrics that were examined in the development of a large-scale Fault Detection, Isolation and Recovery (FDIR) system. The FDIR system is envisioned to perform health management functions for both a launch vehicle and the ground systems that support the vehicle during checkout and launch countdown by using suite of complimentary software tools that alert operators to anomalies and failures in real-time. The FDIR team members developed a set of operational requirements for the models that would be used for fault isolation and worked closely with the vendor of the software tools selected for fault isolation to ensure that the software was able to meet the requirements. Once the requirements were established, example models of sufficient complexity were used to test the performance of the software. The results of the performance testing demonstrated the need for enhancements to the software in order to meet the demands of the full-scale ground and vehicle FDIR system. The paper highlights the importance of the development of operational requirements and preliminary performance testing as a strategy for identifying deficiencies in highly scalable systems and rectifying those deficiencies before they imperil the success of the project

Ferrell, Bob↗
NASA NTRS2016

Potential Cislunar and Interplanetary Proving Ground Excursion Trajectory Concepts

NASA has been investigating potential translunar excursion concepts to take place in the 2020s that would be used to test and demonstrate long duration life support and other systems needed for eventual Mars missions in the 2030s. These potential trajectory concepts could be conducted in the proving ground, a region of cislunar and near-Earth interplanetary space where international space agencies could cooperate to develop the technologies needed for interplanetary spaceflight. Enabled by high power Solar Electric Propulsion (SEP) technologies, the excursion trajectory concepts studied are grouped into three classes of increasing distance from the Earth and increasing technical difficulty: the first class of excursion trajectory concepts would represent a 90-120 day round trip trajectory with abort to Earth options throughout the entire length, the second class would be a 180-210 day round trip trajectory with periods in which aborts would not be available, and the third would be a 300-400 day round trip trajectory without aborts for most of the length of the trip. This paper provides a top-level summary of the trajectory and mission design of representative example missions of these three classes of excursion trajectory concepts.

asteroids↗
NASA NTRS2017

Flight Crew Survey Responses from the Interval Management (IM) Avionics Phase 2 Flight Test

The Interval Management (IM) Avionics Phase 2 flight test used three aircraft over a nineteen day period to operationally evaluate a prototype IM avionics. Quantitative data were collected on aircraft state data and IM spacing algorithm performance, and qualitative data were collected through end-of-scenario and end-of-day flight crew surveys. The majority of the IM operations met the performance goals established for spacing accuracy at the Achieve-by Point and the Planned Termination Point, however there were operations that did not meet goals for a variety of reasons. While the positive spacing accuracy results demonstrate the prototype IM avionics can contribute to the overall air traffic goal, critical issues were also identified that need to be addressed to enhance IM performance. The first category was those issues that impacted the conduct and results of the flight test, but are not part of the IM concept or procedures. These included the design of arrival and approach procedures was not ideal to support speed as the primary control mechanism, the ground-side of the Air Traffic Management Technology Demonstration (ATD-1) integrated concept of operations was not part of the flight test, and the high workload to manually enter the information required to conduct an IM operation. The second category was issues associated with the IM spacing algorithm or flight crew procedures. These issues include the high frequency of IM speed changes and reversals (accelerations), a mismatch between the deceleration rate used by the spacing algorithm and the actual aircraft performance, and some spacing error calculations were sensitive to normal operational variations in aircraft airspeed or altitude which triggered additional IM speed changes. Once the issues in these two categories are addressed, the future IM avionics should have considerable promise supporting the goals of improving system throughput and aircraft efficiency.

Baxley, Brian T.↗
NASA NTRS2002

Application of Reconfigurable Computing Technology to Multi-KiloHertz Micro-Laser Altimeter (MMLA) Data Processing

The Multi-KiloHertz Micro-Laser Altimeter (MMLA) is an aircraft based instrument developed by NASA Goddard Space Flight Center with several potential spaceflight applications. This presentation describes how reconfigurable computing technology was employed to perform MMLA signal extraction in real-time under realistic operating constraints. The MMLA is a "single-photon-counting" airborne laser altimeter that is used to measure land surface features such as topography and vegetation canopy height. This instrument has to date flown a number of times aboard the NASA P3 aircraft acquiring data at a number of sites in the Mid-Atlantic region. This instrument pulses a relatively low-powered laser at a very high rate (10 kHz) and then measures the time-of-flight of discrete returns from the target surface. The instrument then bins these measurements into a two-dimensional array (vertical height vs. horizontal ground track) and selects the most likely signal path through the array. Return data that does not correspond to the selected signal path are classified as noise returns and are then discarded. The MMLA signal extraction algorithm is very compute intensive in that a score must be computed for every possible path through the two dimensional array in order to select the most likely signal path. Given a typical array size with 50 x 6, up to 33 arrays must be processed per second. And for each of these arrays, roughly 12,000 individual paths must be scored. Furthermore, the number of paths increases exponentially with the horizontal size of the array, and linearly with the vertical size. Yet, increasing the horizontal and vertical sizes of the array offer science advantages such as improved range, resolution, and noise rejection. Due to the volume of return data and the compute intensive signal extraction algorithm, the existing PC-based MMLA data system has been unable to perform signal extraction in real-time unless the array is limited in size to one column, This limits the ability of the MMLA to operate in environments with sparse signal returns and a high number of noise return. However, under an IR&D project, an FPGA-based, reconfigurable computing data system has been developed that has been demonstrated to perform real-time signal extraction under realistic operating constraints. This reconfigurable data system is based on the commercially available Firebird Board from Annapolis Microsystems. This PCI board consists of a Xilinx Virtex 2000E FPGA along with 36 MB of SRAM arranged in five separately addressable banks. This board is housed in a rackmount PC with dual 850MHz Pentium processors running the Windows 2000 operating system. This data system performs all signal extraction in hardware on the Firebird, but also runs the existing "software based" signal extraction in tandem for comparison purposes. Using a relatively small amount of the Virtex XCV2000E resources, the reconfigurable data system has demonstrated to improve performance improvement over the existing software based data system by an order of magnitude. Performance could be further improved by employing parallelism. Ground testing and a preliminary engineering test flight aboard the NASA P3 has been performed, during which the reconfigurable data system has been demonstrated to match the results of the existing data system.

Powell, Wesley↗
NASA NTRS1975

DC-9 flight demonstration program with refanned JT8D engines. Volume 1: Summary

The design, analysis, fabrication, and ground and flight testing of DC-9 airframe/nacelle hardware with prototype JT8D-109 engines are discussed. The installation of the JT8D-109 engine on the DC-9 Refan airplane required new or modified hardware for the pylon, nacelle, and fuselage. The acoustic material used in the nose cowl was bonded aluminum honeycomb sandwich and the exhaust duct acoustic material was Inconel 625 Stresskin. The sea level static, standard day bare engine takeoff thrust, the cruise TSFC and the maximum available cruise thrust for the JT8D-109 engine were compared with those of the JT8D-9 engine. The range capabilities of the DC-9 Refan and the production DC-9 airplane were also compared. The Refan airplane demonstrated flight characteristics similar to the production DC-9-30 and satisfied airworthiness requirements. Flyover noise levels were determined for the DC-9 Refan and the DC-9 C-9A airplane for takeoff and landing conditions. Cost estimates were also made.

Source record↗
NASA NTRS1994

Planned In-Space Electric Propulsion Experiments

Ion Propulsion provides an order of magnitude improvement, relative to chemical on-board propulsion systems, of specific impulse at the cost of a relatively small increase in propulsion system dry mass. For civilian space craft, ion propulsion technology provides the potential for increased performance and reduced cost for planetary spacecraft and for large satellites in geostationary orbit. For military applications ion propulsion offers significant benefits for station keeping and repositioning satellites in geostationary orbit. NASA has begun to validate ion propulsion technology for applications to which 2.5 kW to 5.0 kW ion thrusters would be appropriate. NASA's validation program, called NSTAR (NASA SEP Technology Application Readiness), consists of two major elements: a ground test element and an in-space experiment. The Ground Test Element will validate the life, integrability, and performance of low-power ion propulsion. The In-Space Element will demonstrate the ability to integrate and fly an ion propulsion system. As an experiment, it will measure the interactions between the ion propulsion system, the host spacecraft, and the surrounding space plasma; and it will provide a quantitative assessment of the ability of ground testing to replicate the in-space performance of ion thrusters. By involving industry in this program, a commercial source for this technology will be assured. Further, the successful completion of the NSTAR validation program will stimulate commercial and government (both civilian and military) uses of this technology.

ion propulsion planetary spacecraft geostationary ↗
NASA NTRS2008

Final Report on Portable Laser Coating Removal Systems Field Demonstrations and Testing

Processes currently used throughout the National Aeronautics and Space Administration (NASA) to remove corrosion and coatings from structures, ground service equipment and small components results in waste streams consisting of toxic chemicals, spent media blast materials, and waste water. When chemicals are used in these processes they are typically high in volatile organic compounds (VOC) and are considered hazardous air pollutants (HAP). When blast media is used, the volume of hazardous waste generated is increased significantly. Many of the coatings historically used within NASA contain toxic metals such as hexavalent chromium, and lead. These materials are highly regulated and restrictions on worker exposure continue to increase. Most recently the EPA reduced the permissible exposure limit (PEL) for hexavalent chromium. The new standard lowers OSHA's PEL for hexavalent chromium from 52 to 5 micrograms of Cr(V1) per cubic meter of air as an 8-hour time-weighted average. Hexavalent chromium is found in the pretreatment and primer coatings used within the Shuttle Program. In response to the need to continue to protect assets within the agency and the growing concern over these new regulations, NASA is researching different ways to continue the required maintenance of both facility and flight equipment in a safe, efficient and environmentally preferable manner. The use of laser energy to remove prepare surfaces for a variety of processes, such as corrosion and coating removal, weld preparation and non destructive evaluation is a relatively new technology that has shown itself to be environmentally preferable and in many cases less labor intensive than currently used removal methods. The development of a Portable Laser Coating Removal System (PLCRS) started as the goal of a Joint Group on Pollution Prevention (JG-PP) project, led by the Air Force, where several types of lasers in several configurations were thoroughly evaluated. Following this project, NASA decided to evaluate the best performers on processes and coatings specific to the agency. Laser systems used during this project were all of a similar design, most of which had integrated vacuum systems in order to collect materials removed from substrate surfaces during operation. Due to the fact that the technology lends itself to a bide variety of processes, several site demonstrations were organized in order to allow for greater evaluation of the laser systems across NASA. The project consisted of an introductory demonstration and a more in-depth evaluation at Wright-Patterson Air Force Base. Additionally, field demonstrations occurred at Glenn Research Center and Kennedy Space Center. During these demonstrations several NASA specific applications were evaluated, including the removal of coatings within Orbiter tile cavities and Teflon from Space Shuttle Main Engine gaskets, removal of heavy grease from Solid Rocket Booster components and the removal of coatings on weld lines for Shuttle and general ground service equipment for non destructive evaluation (NDE). In addition, several general industry applications such as corrosion removal, structural coating removal, weld-line preparation and surface cleaning were evaluated. This included removal of coatings and corrosion from surfaces containing lead-based coatings and applications similar to launch-structure maintenance and Crawler maintenance. During the project lifecycle, an attempt was made to answer process specific concerns and questions as they arose. Some of these initially unexpected questions concerned the effects lasers might have on substrates used on flight equipment including strength, surface re-melting, substrate temperature and corrosion resistance effects. Additionally a concern was PPE required for operating such a system including eye, breathing and hearing protection. Most of these questions although not initially planned, were fully explored as a part of this project. Generally the results from tesng were very positive. Corrosion was effectively removed from steel, but less successfully from aluminum alloys. Coatings were able to be removed, with varying results, generally dark, matte and thin coatings were easier to remove. Steel and aluminum panels were able to be cleaned for welding, with no known deleterious effects and weld-lines were able to have coatings removed in critical areas for NDE while saving time as compared to other methods.

Rothgeb, Matthew J.↗
NASA NTRS2014

Forward Bay Cover Separation Modeling and Testing for the Orion Multi-Purpose Crew Vehicle

Spacecraft multi‐body separation events during atmospheric descent require complex testing and analysis to validate the flight separation dynamics model and to verify no recontact. NASA Orion Multi‐Purpose Crew Vehicle (MPCV) teams examined key model parameters and risk areas to develop a robust but affordable test campaign in order to validate and verify the Forward Bay Cover (FBC) separation event for Exploration Flight Test‐1 (EFT‐1). The FBC jettison simulation model is highly complex, consisting of dozens of parameters varied simultaneously, with numerous multi‐parameter interactions (coupling and feedback) among the various model elements, and encompassing distinct near‐field, mid‐field, and far‐field regimes. The test campaign was composed of component‐level testing (for example gas‐piston thrusters and parachute mortars), ground FBC jettison tests, and FBC jettison air‐drop tests that were accomplished by a highly multi‐disciplinary team. Three ground jettison tests isolated the testing of mechanisms and structures to anchor the simulation models excluding aerodynamic effects. Subsequently, two air‐drop tests added aerodynamic and parachute parameters, and served as integrated system demonstrations, which had been preliminarily explored during the Orion Pad Abort‐1 (PA‐1) flight test in May 2010. Both ground and drop tests provided extensive data to validate analytical models and to verify the FBC jettison event for EFT‐1, but more testing is required to support human certification, for which NASA and Lockheed Martin are applying knowledge from Apollo and EFT‐1 testing and modeling to develop a robust but affordable human spacecraft capability.

Ali, Yasmin↗
NASA NTRS1973

Skylab Rescue Space Vehicle OAT No. 1 Plugs in Test

A test is described which demonstrates the compatibility of the Skylab Rescue Space Vehicle systems, the ground support equipment, and off-site support facilities by proceeding through a simulated launch countdown, liftoff, and flight. The functions of propellant loading, umbilical ejection, holddown arm release, service arm retraction, liftoff, and inflight separation are simulated. An external power source supplies transfer power to internal, and instrument unit commands are simulated by the digital command system. The test outline is presented along with a list of references, intercommunications information, radio frequency matrix, and interface control chart.

Jevitt, S. J.↗