Search NASA⌕ Search

SEARCH · Search NASA

Results for “LOADS - TAIL SURFACES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Modeling surface deformations at complex strike-slip plate boundaries

Two new versions of the physical base-traction model of Li and Rice (1987) have been developed to study the loading processes and surface deformation near plate boundaries with geometric complexities, including a shallow creeping fault segment and two subparallel faults. Predictions of surface velocity and surface slip rate for the region between the San Andreas fault and the Pacific coast at the latitude of the Parkfield-Cholame segment using model parameters based on geologic, geodetic, and seismic considerations were found to be in good agreement with contemporary geodetic field data (not used in constrainning model parameters). Also, predicted surface velocity for the Salton Sea-Coachella Valley area were fit to recently derived contemporary geodetic data and very large baseline interferometry data, althoug here the model parameters are not well constrained.

Li, Victor C.↗
NASA NTRSDate not supplied

CDISC Remote Design Method to Simulate Aircraft Interference Effects for the CATNLF Flight Test

The Crossflow Attenuated Natural Laminar Flow (CATNLF) flight test is an experimental evaluation of a laminar flow design approach that will be conducted on a small transonic wing-like model suspended from the Centerline Instrumented Pylon (CLIP) underneath an F-15 vehicle. The upcoming flight test is anticipated to provide experimental data that may be useful for transition prediction code calibrations or laminar flow computational studies. For the computational results to be reliable, relevant aerodynamics must be included in the simulations. It has been shown that the F-15 vehicle produces a notable aerodynamic influence on the CATNLF test article, and that removing the F-15 vehicle from the simulation significantly alters the laminar flow behavior. Because the F-15 vehicle is not a publicly-releasable geometry, if the CATNLF flight test dataset is to be widely used by the community, an alternative method to ensure that the CATNLF test article flight configuration aerodynamics is properly modeled is required. The objective of this research is to use the CDISC aerodynamic design tool to perform a remote design of a surface that would replicate the aerodynamic influence on the CATNLF test article. This new design approach, referred to as the Equivalent Loading via Interference Surface Effects (ELISE), is presented in this paper, including the details on the design setup and results. The ELISE design successfully reproduced the F-15 influence on the CATNLF test article, with predicted transition location within an average of 4% chord of the full flight configuration. An off-design assessment is included for small perturbations in Mach and sideslip angle that suggest the ELISE design can cover a reasonable range of expected flight conditions with the same geometry. This paper is intended to explain the design approach, as well as show results that can be expected when utilizing the ELISE design method.

CDISC↗
NASA NTRSDate not supplied

CDISC Remote Design Method to Simulate Aircraft Interference Effects for the CATNLF Flight Test

The Crossflow Attenuated Natural Laminar Flow (CATNLF)flight test is an experimental evaluation of a laminar flow design approach that will be conducted on a small transonic wing-like model suspended from the Centerline Instrumented Pylon (CLIP) underneath an F-15 vehicle. The upcoming flight testis anticipated to provide experimental data that may be useful for transition prediction code calibrations or laminar flow computational studies. For the computational results to be reliable, relevant aerodynamics must be included in the simulations. It has been shown that the F-15 vehicle produces a notable aerodynamic influence on the CATNLF test article, and that removing the F-15 vehicle from the simulation significantly alters the laminar flow behavior. Because the F-15 vehicle is not a publicly-releasable geometry, if the CATNLF flight test dataset is to be widely used by the community, an alternative method to ensure that the CATNLF test article flight configuration aerodynamics is properly modeled is required. The objective of this research is to use the CDISC aerodynamic design tool to perform a remote design of a surface that would replicate the aerodynamic influence on the CATNLF test article. This new design approach, referred to as the Equivalent Loading via Interference Surface Effects (ELISE), is presented in this paper, including the details on the design setup and results. The ELISE design successfully reproduced theF-15 influence on the CATNLF test article, with predicted transition location within an average of 4% chord of the full flight configuration. An off-design assessment is included for small perturbations in Mach and sideslip angle that suggest the ELISE design can cover a reasonable range of expected flight conditions with the same geometry. This paper is intended to explain the design approach, as well as show results that can be expected when utilizing the ELISE design method.

CDISC↗
DOE OSTI2023

A renewable lignin-based thermoplastic adhesive for steel joining

Adhesive bonding of metals has become increasingly relevant in recent years due to the demand for reducing weight and improving performance in structural applications such as automobiles and aerospace. We developed renewable thermoplastic adhesives from technical organosolv lignin isolated from hardwood biomass and acrylonitrile butadiene co-polymer rubber (NBR) for joining steel substrates. NBR33, NBR41 and NBR51 with acrylonitrile molar ratios of 33, 41 and 51%, respectively, were blended with lignin to form two-phase thermoplastic adhesives, and their adhesion, viscoelastic and surface properties were measured. Lignin content in the compositions were varied, ranging from 40% to 80% (w/w), to alter toughness, stiffness, and surface energy characteristics of the material. Better interaction or reactivity between the lignin and NBR phases was observed with greater nitrile content in NBR, leading to greater modulus and stiffness of the adhesive. Simultaneously, increasing the proportion of lignin reduced toughness and improved stiffness, with the highest adhesive strength of 13.1 MPa measured in a 60% lignin loading ratio with NBR51. Surface energy measurements revealed that total surface energy (sum of polar and dispersive surface energy) raised with lignin loading, suggesting that both surface energy and matrix strength play a critical role in the adhesive properties of the synthesized materials. A finite element-based cohesive zone model (CZM) was developed and implemented to study the failure strength of the adhesively bonded joint. Here, this study demonstrates the viability of lignin as a valuable building block for adhesives, not only due to its inherent chemical structure and rigidity, but also for its surface energy characteristics.

36 MATERIALS SCIENCE↗
NASA NTRS1982

Static calibration for measurement of loads in wind tunnel tests on Shuttle surface tiles

A description is given of the procedures used for the static calibrations of the Coe (1981) sensor array to determine normal force, pitching moment, and rolling moment from the ensemble of sensor outputs. The use of independent data to confirm the validity of the calibration is also described. Two methods are used in calibrating the Coe sensors. In the first, calibration loads and readings are arranged in matrix form and are assumed to be related in a linear fashion. In the second, each Coe sensor reading is regarded as a sum of contributions from each of the calibration loads. It is shown that the Coe load sensors, in conjunction with either of two data analysis methods, can be used to determine the forces and moments experienced by a Shuttle TPS tile.

Rummler, D. R.↗
DOE OSTI2025

High-Loading Single-Atom Catalyst via On-Surface Synthesis of a Metal-Covalent Organic Framework for Oxygen Reduction Reaction

The development of active catalysts with both high metal efficiency and use of earth abundant metals is the ultimate goal for advancing the required commercially viable and sustainable energy conversion technologies of the future. Metal-organic frameworks (MOFs) have emerged as promising candidates due to their high surface area and tunable active sites. Here, this study aims to fabricate a new type of high metal loading single-atom catalysts (SACs) based on 2D metal-organic covalent organic frameworks (MCOFs) with uniform, active and stable Fe-N 3 sites. The MCOFs were synthesized through an on-surface polymerization process using Fe and melamine as precursors. The polymerization steps were characterized using operando high-pressure scanning tunneling microscopy (HP-STM), in situ X-ray photoelectron spectroscopy (XPS), low-temperature STM (LT-STM), and computational calculations. The synthesized MCOFs demonstrated favorable adsorption and activation of O 2 at the Fe-N 3 sites, and it is predicted to be active for the oxygen reduction reaction (ORR). The surface chemistry and functionality of 2D MCOFs can be rationally designed by varying the metal atoms and organic linkers, offering a versatile platform for diverse applications.

25 ENERGY STORAGE↗
DOE OSTI2023

Hierarchical thermal-conductive polymer nanocomposites for thermal management

Managing heat in electrical conductors is a major challenge to meet the demands for sustainable energy use and electrical reliability, most notably power electronics and energy-critical electrical machines. Achieving such disparate functionalities, such as high temperature thermal and electrical reliability, require rational design and manufacturing of thermal conductor material and its hierarchical structures. Here we present hierarchical thermal-conductive nanocomposites, consisting of nanostructured ceramic conformal coating and aligned ultrahigh molecular weight polyethylene fiber, to tailor heat dissipation in electric conductors. The hybrid aligned thermal interface exhibits a highly desirable temperature dependent anisotropic high thermal conductivity with 0.98W m –1 K –1 and dielectric strength with 3.4. In addition, electrically insulating thermal interfaces demonstrate high-performing and reliable electrical systems under the dynamic load conditions. The surface temperature of heterogeneous ceramic-polymer encapsulated conductor is 17.8 °C lower than that of polymer-encapsulated conductor at the same electrical load. Consequently, the findings shown here hold great promises for directing heat extraction in electrical machine systems, advancing thermal management for emerging electronic applications.

36 MATERIALS SCIENCE↗
NASA NTRS1981

Wind-simulation tester for solar modules

Tester induces cyclic pressure loads across module surface, guaranteeing its mechanical integrity. Module to be tested is sandwiched between stiffened aluminum layers covered with rubber sheets. Automatic front and back pressure loading is cycled by pneumatic system on separate stand. Relief valves prevent overpressuring. Fixture operates at high speed, completing cycle in 5 seconds, and typically applies 2,400 pascals.

Griffith, J. S.↗
NASA NTRS1982

A doublet lattice method for the determination of rotor induced empennage vibration airloads. Analysis description and program documentation

An efficient state-of-the-art method was developed to determine the unteady vibratory airloads produced by the interaction of the main rotor wake with a helicopter empennage. This method was incorporated into a computer program, Rotor Induced Empennage Vibration Analysis (RIEVA). The program requires the main rotor wake position and the strength of the vortices locates near the empennage surfaces. A nonlinear lifting surface analysis is utilized to predict the aerodynamic loads on the empennage surfaces in the presence of these concentrated vortices. The analysis was formulated to include all pertinent effects such as suction of the interacting vortices and the shed vorticity behind the empennage surfaces. The analysis employs a time domain solution. The output of the program consists of chordwise and spanwise airload distributions on the empennage surfaces. The airload distributions are harmonically analyzed and formulated for input into the Coupled Rotor/Airframe Vibration Analysis.

Gangwani, S. T.↗
NASA NTRS1987

The thermal environment of transatmospheric vehicles

A transatmospheric vehicle using primarily air-breathing propulsion must fly in the denser part of the atmosphere to achieve adequate acceleration to reach orbital speed. The potentially long ascent times, combined with the need for a low-drag configuration, result in a severe aerothermodynamics environment. To achieve low drag, the vehicle must have a relatively sharp nose and wing leading edges. The ascent peak stagnation point and equilibrium wall temperatures for the wing leading edge can reach values of 4000 K and 3000 K, respectively, for high dynamic pressure trajectories, making some form of mass addition cooling mandatory. The corresponding temperatures during entry are about 1500 K lower. The vehicle windward centerline temperatures are more moderate, however, with values peaking around 1500 K. Therefore, radiative cooling should be effective over large areas of the vehicle. The windward, centerline heat loads are relatively insensitive to the dynamic pressure of the ascent trajectory, in contrast to the stagnation point and wing leading edge. The windward surface entry heat loads are much lower, but depend strongly on the flightpath.

Tauber, Michael E.↗
NASA NTRS1992

Polyphosphazene Icephobic Coating Materials

Coating materials consisting mostly of modified polyphosphazene (Class FZ) elastomers provide better protection against icing than fluorocarbon polymers and silicone elastomers. Reduces adhesive force between ice and surface. As consequence, increasing weight of ice, wind loading, or vibration of surface causes ice to be shed. New icephobic coats reduce accumulation of ice on aircraft, radomes, antennas, ships, and power-transmission lines.

Willis, Paul B.↗
NASA NTRS1993

Deflecting Shearpin

Spring loading helps prevent permanent deformation of adjacent bearing surfaces. Shearpin deflects as load compresses inner spring. Maximum deflection determined by gap between halves of capture ring. Beyond deflection, pin acts as standard shearpin.

Gregory, Peyton B.↗
NASA NTRS2022

Investigating Particle-Particle Electrostatic Effects on Charged Lunar Dust Transport via Discrete Element Modeling

NASA surface exploration missions have always seen negative effects of dust including the Apollo missions. The astronaut-witnessed unusual behavior of the dust particles that surround the vehicle after engine cutoff has the potential to have more of an influence on surface systems dust loading than the high velocity lunar rocket plume ejecta in the landing process. The levitation and transport of the fine components of regolith on lunar surface has been linked to electrostatic effects and electric field, but so far there is no accurate model considering the inter-particle electrostatic interactions, especially when the particles are charged by rocket plume or other mechanical interactions due to exploration activities. This study is proposed to investigate the dynamics of charged lunar regolith with a discrete element method (DEM) approach focusing on the inter-particle interactions and contact charge transfer. The grain dynamics is coupled with mechanical and electrical particle interactions, and both short- and long-range interactions between spherical particles are incorporated. A tribo-charging model based on instantaneous collisions between particles is adopted and validated by comparing the simulation results to existing experimental data. Sensitivity analysis is conducted to quantify the effects of initial charge, tribo-charging, and E-field on transport of lunar dust based on JSC-1 simulants with a radius of 50 lm. DEM simulations are also conducted in a near realistic lunar environment with the estimations of initial conditions that shows the difference in position and velocity distributions between charged particles and uncharged particles. The results indicate that the charged dust particles have higher dispersion of position and velocity by several orders of magnitude due to electrostatic effects. This provides a potential explanation for the phenomena of the approximately 30 s dust lofting following Apollo Lunar Module landing.

Lunar dust↗
NASA NTRS1981

Methods for estimating pressure and thermal loads induced by elevon deflections on hypersonic-vehicle surfaces with turbulent boundary layers

Empirical anaytic methods are presented for calculating thermal and pressure distributions in three-dimensional, shock-wave turbulent-boundary-layer, interaction-flow regions on the surface of controllable hypersonic aircraft and missiles. The methods, based on several experimental investigations, are useful and reliable for estimating both the extent and magnitude of the increased thermal and pressure loads on the vehicle surfaces.

Kaufman, L. G., II↗
NASA NTRS1990

Behavior of surface and corner cracks subjected to tensile and bending loads in Ti-6Al-4V alloy

The behavior of part-through flaws with regard to failure under monotonic loading and their growth under fatigue loading was studied experimentally and analytically. Comparisons are made of experimental values of toughness obtained using surface and corner cracked specimens with those obtained using standard test specimens, and also experimental growth cycles were compared with numerical predictions using the NASA/FLAGRO computer program. Tests were conducted on various types of surface and corner cracks under tensile and bending loads. Room temperature lab air provided the test environment. The material used in this study was the Ti-6Al-4V alloy in the solution treated and aged (STA) and stress relieved condition. Detailed tabulation of the fracture toughness data and results of life prediction using the NASA/FLAGRO program are presented. Fatigue crack growth rates for the part-through cracked specimens are compared with a base curve fitted from the data obtained using standard specimens. The fatigue loading used in the crack growth testing was constant-amplitude sinusoidal type.

Forman, Royce G.↗
NASA NTRS2005

High-Frequency, High-Temperature Fretting Experiments

Fretting is a structural damage mechanism observed when two nominally clamped surfaces are subjected to an oscillatory loading. A critical location for fretting induced damage has been identified at the blade/disk and blade/damper interfaces of gas turbine engine turbomachinery and space propulsion components. The high-temperature, high-frequency loading environment seen by these components lead to severe stress gradients at the edge-of-contact. These contact stresses drive crack nucleation and propagation in fretting and are very sensitive to the geometry of the contacting bodies, the contact loads, materials, temperature, and contact surface tribology (friction). To diagnose the threat that small and relatively undetectable fretting cracks pose to damage tolerance and structural integrity of in-service components, the objective of this work is to develop a well-characterized experimental fretting rig capable of investigating fretting behavior of advanced aerospace alloys subjected to load and temperature conditions representative of such turbomachinery components.

Matlik, J. F.↗
DOE OSTI2020

Surface modification of ZIF ‐90 with triptycene for enhanced interfacial interaction in mixed‐matrix membranes for gas separation

Abstract Zeolite imidazole framework (ZIF‐90) nanoparticles were chemically modified by grafting triptycene moieties. The modified nanoparticles were introduced into a triptycene‐based polyimide as fillers to generate mixed matrix membranes (MMMs) for gas separation. The incorporation of “hook‐like” triptycene moieties in both dispersed and continuous phases led to intimate contact between the two phases and thus defect‐free interfacial morphology, due to the supramolecular interlocking and π–π stacking interaction between triptycene units presented in both phases. The filler/polymer solution showed shear thickening behavior due to such strong interfacial interaction. The separation performance of the prepared composite membranes was investigated as a function of filler loading and particle surface grafting density. Pure‐gas permeation results showed that the gas permeabilities increased expectedly as the filler loading increased, with stable or improved selectivities. The reduced permeability relative to pristine polyimide film is likely due to the pore blockage of ZIF‐90 upon grafting triptycene moieties on the particle surface. Reducing the grafting density of triptycene moieties led to improved permeability and selectivity suggesting good tunability of this series of new composite membranes. Overall, modification of nanofiller with hierarchical triptycene moieties offers a fundamentally new avenue for creation of composite membranes with unique properties in gas separations.

Zhang, Qinnan↗
NASA NTRS1985

Permafrost and Subsurface Ice in the Solar System

The properties and behavior of planetary permafrost are discussed with reference to the ability of such surfaces to sustain loads characteristics of spacecraft landing and planetary bases. In most occurrences, water ice is in close proximity to, or in contact with, finely divided silicate mineral matter. When ice contacts silicate mineral surfaces, a liquid-like, transition zone is created. Its thickness ranges from several hundred Angstron units at temperatures near 0 degrees C to about three Angstrom units at -150 degrees C. When soluble substances are present, the resulting brine enlarges the interfacial zone. When clays are involved, although the interfacial zone may be small, its extent is large. The unfrozen, interfacial water may amount to 100% or more weight at a temperature of -5 degrees C. The presence of this interfacial unfrozen water acts to confer plasticity to permafrost, enabling it to exhibit creep at all imposed levels of stress. Nucleation processes and load-bearing capacity are examined.

Anderson, D. M.↗