WING AND FLAP LOADS OBTAINED FROM A WIND-TUNNEL INVESTIGATION OF LARGE-SCALE V STOL MODEL
Wing and flap loads of v/stol aircraft - wind tunnel study
WING LOADING↗
SEARCH · Search NASA
Results for “Large load”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
OC6 project Phase III: validation of the aerodynamic loading on a wind turbine rotor undergoing large motion caused by a floating support structure
Abstract. This paper provides a summary of the work done within Phase III of the Offshore Code Comparison Collaboration, Continued, with Correlation and unCertainty (OC6) project, under the International Energy Agency Wind Technology Collaboration Programme Task 30. This phase focused on validating the aerodynamic loading on a wind turbine rotor undergoing large motion caused by a floating support structure. Numerical models of the Technical University of Denmark 10 MW reference wind turbine were validated using measurement data from a 1:75 scale test performed during the UNsteady Aerodynamics for FLOating Wind (UNAFLOW) project and a follow-on experimental campaign, both performed at the Politecnico di Milano wind tunnel. Validation of the models was performed by comparing the loads for steady (fixed platform) and unsteady (harmonic motion of the platform) wind conditions. For the unsteady wind conditions, the platform was forced to oscillate in the surge and pitch directions under several frequencies and amplitudes. These oscillations result in a wind variation that impacts the rotor loads (e.g., thrust and torque). For the conditions studied in these tests, the system aerodynamic response was almost steady. Only a small hysteresis in airfoil performance undergoing angle of attack variations in attached flow was observed. During the experiments, the rotor speed and blade pitch angle were held constant. However, in real wind turbine operating conditions, the surge and pitch variations would result in rotor speed variations and/or blade pitch actuations, depending on the wind turbine controller region that the system is operating. Additional simulations with these control parameters were conducted to verify the fidelity of different models. Participant results showed, in general, a good agreement with the experimental measurements and the need to account for dynamic inflow when there are changes in the flow conditions due to the rotor speed variations or blade pitch actuations in response to surge and pitch motion. Numerical models not accounting for dynamic inflow effects predicted rotor loads that were 9 % lower in amplitude during rotor speed variations and 18 % higher in amplitude during blade pitch actuations.
17 WIND ENERGY↗
Experimental and Simulation Analysis of Binary Mixtures of Biomass and Inert Material
A literature review was conducted to identify experiments on various scales of biomass combustion specific to circulating fluidized bed (CFB) combustors. Typical feedstock and inert bed material characteristics for biomass combustion in a CFB were gathered. This information was used to design laboratory-scale, non-reacting experiments on biomass-inert bed material mixtures in a 1-in. cylindrical test rig in the Multiphase Flow Analysis Laboratory (MFAL) in Morgantown, WV. The biomass chosen was a hardwood. Pellets from the hardwood were milled and sieved to obtain three size ranges—small, medium, and large. Three mass loadings of each of the biomass samples were fluidized with glass beads as the inert bed material to study the mixing characteristics under varying fluidizing gas velocities. Hydrodynamic data including pressure drop measurements at select vertical locations and video recordings of the mixture behavior were generated in this effort.
09 BIOMASS FUELS↗
Practical considerations in aeroelastic design
The structural design process for large transport aircraft is described. Critical loads must be determined from a large number of load cases within the flight maneuver envelope. The structural design is also constrained by considerations of producibility, reliability, maintainability, durability, and damage tolerance, as well as impact dynamics and multiple constraints due to flutter and aeroelasticity. Aircraft aeroelastic design considerations in three distinct areas of product development (preliminary design, advanced design, and detailed design) are presented and contrasted. The present state of the art is challenged to solve the practical difficulties associated with design, analysis, and redesign within cost and schedule constraints. The current practice consists of largely independent engineering disciplines operating with unorganized data interfaces. The need is then demonstrated for a well-planned computerized aeroelastic structural design optimization system operating with a common interdisciplinary data base. This system must incorporate automated interfaces between modular programs. In each phase of the design process, a common finite-element model for static and dynamic optimization is required to reduce errors due to modeling discrepancies. As the design proceeds from the simple models in preliminary design to the more complex models in advanced and detailed design, a means of retrieving design data from the previous models must be established.
Rommel, B. A.↗
Physics-Informed Sparse Gaussian Process for Probabilistic Stability Analysis of Large-Scale Power System with Dynamic PVs and Loads
This work proposes a physics-informed sparse Gaussian process (SGP) for probabilistic stability assessment of large-scale power systems in the presence of uncertain dynamic PVs and loads. The differential and algebraic equations considering uncertainties from dynamic PVs and loads are reformulated to a nonlinear mapping relationship that allows the application of SGP. Thanks to the nonparametric characteristic of Gaussian process, the proposed framework does not require distributions of uncertain inputs and this distinguishes it from existing approaches. As the original Gaussian process is not scalable to large-scale systems with high dimensional uncertain inputs, this paper develops the SGP with a stochastic variational inference technique. It leads to approximately two orders of complex reduction. A data pre-processing step is also introduced to tackle the coexistence of stable and unstable cases by sample clustering and constructing separate SGPs. The probabilistic transient stability index is analyzed to assess system stability under different uncertain dynamics loads and PVs. Comparisons are performed with the sampling-based, the polynomial chaos expansion-based, and traditional Gaussian process-based methods on the modified IEEE 118-bus and Texas 2000-bus systems under various scenarios, including different levels of uncertainties and the existence of nonlinear correlations among dynamic PVs. The impacts of data quality and quantity issues are also investigated. It is shown that the proposed SGP achieves significantly improved computational efficiency while maintaining high accuracy with a limited number of data.
24 POWER TRANSMISSION AND DISTRIBUTION↗
High-Fidelity Large-Signal Order Reduction Approach for Composite Load Model
With the increasing penetration of electronic loads and distributed energy resources, conventional load models cannot capture their dynamics. Therefore, a new comprehensive composite load model is developed by Western Electricity Coordinating Council (WECC). However, this model is a complex high-order non-linear system with multi-time-scale property, which poses challenges on power system studies with heavy computational burden. In order to reduce the model complexity, the authors firstly develop a large-signal order reduction (LSOR) method using singular perturbation theory. In this method, the fast dynamics are integrated into the slow ones to preserve transient characteristics of the former. Then, accuracy assessment conditions are proposed and embedded into the LSOR to improve and guarantee the accuracy of reduced-order model. Finally, the reduced-order WECC composite load model is derived by using the proposed algorithm. Overall, simulation results show that the reduced-order large-signal model significantly alleviates the computational burden while maintaining similar dynamic responses as the original composite load model.
24 POWER TRANSMISSION AND DISTRIBUTION↗
Probabilistic load simulation: Code development status
The objective of the Composite Load Spectra (CLS) project is to develop generic load models to simulate the composite load spectra that are included in space propulsion system components. The probabilistic loads thus generated are part of the probabilistic design analysis (PDA) of a space propulsion system that also includes probabilistic structural analyses, reliability, and risk evaluations. Probabilistic load simulation for space propulsion systems demands sophisticated probabilistic methodology and requires large amounts of load information and engineering data. The CLS approach is to implement a knowledge based system coupled with a probabilistic load simulation module. The knowledge base manages and furnishes load information and expertise and sets up the simulation runs. The load simulation module performs the numerical computation to generate the probabilistic loads with load information supplied from the CLS knowledge base.
Newell, J. F.↗
Chordwise and Spanwise Loadings Measured at Low Speed on Large Triangular Wings
Explore the source record for details and available documents.
Anderson, Adrien E↗
AERODYNAMIC CHARACTERISTICS IN GROUND EFFECT OF A LARGE-SCALE MODEL WITH A HIGH DISK-LOADING LIFTING FAN MOUNTED IN THE FUSELAGE
Aerodynamic characteristics in ground effect of a large scale model
AERODYNAMIC CHARACTERISTICS↗
Characterization of Side Load Phenomena Using Measurement of Fluid/Structure Interaction
During ground-tests of most production rocket engines over the last 30 years, large asymmetric transient side loads coming from the nozzle and related steady-state vibrational loads within the nozzle have been measured. The widely varying magnitude of these loads has been large enough to fail interfacing components as well as nozzles in these engines. This paper will discuss a comprehensive test and analysis program that has been undertaken to develop a methodology to accurately predict the character and magnitude of this loading. The project to-date has incorporated analytical modeling of both the fluid flow and the nozzle structure and testing of both full-scale and sub-scale rocket nodes. Examination of the test data indicates that one of the two-nodal diameter structural modes may be interacting with flow separation from the nozzle inside-wall in a self-excited or aeroelastic vibration phenomenon. If verified, this observation will be used to develop a methodology for design and analysis. A fuller understanding of the characteristics of this vibration will provide an increase in the accuracy and confidence of side load predictions, which will be critical for the successful construction of the next generation of low-cost, reliable rocket engines.
Brown, Andrew M.↗
The role of superconductivity in magnetic bearings for high-load applications
Slewing of large payloads will require control torque and angular momentum storage capacities that are large in comparison to the capabilities of available control moment gyros (CMG's). SatCon Technology Corporation is currently designing a CMG which may be employed as a slew actuator for large spacecraft or other payloads. The slew actuator employs a type of magnetic bearing which may be used in high load applications. The magnetic bearing is also used to fully gimbal the suspended rotor of the slew actuator. The use of magnetic bearings in angular momentum exchange actuators has the primary advantage that physical contact between the rotor and stator is eliminated. This leads to greatly extended life, increased reliability, and reduced vibrations. Several actuators operating on magnetic bearings have been demonstrated in previous research efforts. These were sized for use in small satellites. For conventional magnetic bearings, which employ magnetic cores, high torsional loading may require that the magnetic structure be excessively massive. An alternative magnetic bearing design which employs a superconducting coil and eliminates conventional magnetic structures is discussed. The baseline approach is to replace the field coil of a conventional magnetic bearing with the superconducting coil.
Downer, James↗
Loading Considerations for Implementing Friction STIR Welding for Large Diameter Tank Fabrication
The main objectives of the research presented here are to determine the reaction loads associated with friction stir welding (FSW) and to determine the suitability of an existing welding fixture for implementing this welding process in the fabrication of large diameter tanks. Friction stir welding is a relatively new process which is being investigated as a method for joining aluminum alloys. The aluminum-lithium alloy, Al-Li 2195, which is being used to fabricate the super-light-weight shuttle external tank has proven difficult to join using fusion techniques. Therefore, FSW and its potential applicability to joining Al-Li 2195 are of particular interest to NASA.
Adams, Glynn↗
Helicopter sling loads
Computer program compares various control-system concepts for improving handling qualities of single-rotor helicopters carrying relatively-large external sling loads. Computer program developed to test these and other ideas helps to circumvent expensive prototype and field testing. Comparisons between (1) computed data and flight data, (2) simulation-system values and flight test data, and (3) pilot evaluations of simulation and actual-flight conditions are very favorable.
Shaughnessy, J. D.↗
Inelastic, nonlinear analysis of stiffened shells of revolution by numerical integration
This paper describes the latest addition to the STARS system of computer programs, STARS-2P, for the plastic, large deflection analysis of axisymmetrically loaded shells of revolution. The STARS system uses a numerical integration scheme to solve the governing differential equations. Several unique features for shell of revolution programs that are included in the STARS-2P program are described. These include orthotropic nonlinear kinematic hardening theory, a variety of shell wall cross sections and discrete ring stiffeners, cyclic and nonproportional mechanical and thermal loading capability, the coupled axisymmetric large deflection elasto-plastic torsion problem, an extensive restart option, arbitrary branching capability, and the provision for the inelastic treatment of smeared stiffeners, isogrid, and waffle wall constructions. To affirm the validity of the results, comparisons with available theoretical and experimental data are presented.
Levine, H. S.↗
Distribution System Segmented Model Simplification with Independent Dynamically Changing End-Use Loads
With more emerging technologies in power distribution systems, to support quasi-static time-series (QSTS) simulation over short time frames, accurately modeling the dynamic behavior of end-use load under various conditions is im- portant. However, time and cost can be a burden for the QSTS simulation of thousands of houses representing dynamic load behaviors on large distribution feeders. There are two main contributions of this paper in order to reduce the QSTS simulation complexity. First, the paper presents a method to stochasti- cally model the dynamic behavior of end-use load for QSTS simulations. Second, using the stochastically modeled load behavior as an input to a distribution sys- tem, and building on our previous QSTS simulation simplification/acceleration method that relies on uniform load behavior, this paper presents a segment substitution approach for the simplification of distribution system models with independent dynamically changing end-use loads. Our numerical results show that compared to GridLAB-D, a software tool that simulates end-use load be- havior through physical models, the proposed stochastic modeling approach achieved an 89.3% simulation time reduction for end-use loads, while accurately capturing the temporally changing total load behavior. Moreover, the QSTS simulation of a large test distribution system through OpenDSS showed that the proposed simplification method decreased the feeder simulation time by a factor of three at less than 0.3% voltage error. Compared to our previous method with independent dynamic loads, the voltage error is reduced by a factor of four.
Power distribution system modeling, stochastic pro↗
Trends in high-speed atmospheric flight
Some of the current problems and future trends for three types of flight within the Earth's atmosphere are considered. The three areas examined are atmosphere entry at very high speeds, atmosphere exit of launch vehicles, and sustained cruise within the atmosphere. The high-speed entry problems described are those encountered by vehicles returning to Earth after a manned mission to Mars. Such vehicles will experience atmosphere entry speeds up to 50,000 and perhaps as high as 70,000 feet per second. For these vehicles to execute a successful entry, accurate guidance at Earth approach must be provided and very precise control during the flight within the atmosphere will be a necessity. At the high entry speeds radiative heating-is greater than convective and thus it tends to exert a dominant influence on entry-vehicle configuration. The study and development of relatively slender vehicles is indicated in order to minimize the large radiative heating loads and associated heat-shield weights. Manned interplanetary missions in the future may also involve a need for very large launch vehicles. These large vehicles will have aerodynamic problems which differ somewhat from current problems. For example, drag losses decrease with increasing size and large vehicles may thus be of lower fineness ratio than present-day vehicles. With lower fineness ratio some of the difficult current problems produced by ground-wind loads and by buffet of hammerhead payload mountings will be avoided. In the case of high-speed cruise within the Earth's atmosphere, the use of hydrogen-fueled, airbreathing engines may permit attractive payload capabilities for long-range high-speed transports. For such vehicles aerodynamic problems arise because of the numerous constraints placed upon their flight paths as well as from the large volumes required for the hydrogen fuel. From payload considerations alone, attractive cruise speeds for such vehicles currently appear to be about twice that of the conventionally fueled supersonic transports now being intensively studied.
Atmospheric entry↗
Designing and Implementing an OVERFLOW Reader for ParaView and Comparing Performance Between Central Processing Units and Graphical Processing Units
In the Applied Aerosciences and CFD branch at Johnson Space Center, computational simulations are run that face many challenges. Two of which are the ability to customize software for specialized needs and the need to run simulations as fast as possible. There are many different tools that are used for running these simulations and each one has its own pros and cons. Once these simulations are run, there needs to be software capable of visualizing the results in an appealing manner. Some of this software is called open source, meaning that anyone can edit the source code to make modifications and distribute it to all other users in a future release. This is very useful, especially in this branch where many different tools are being used. File readers can be written to load any file format into a program, to ease the bridging from one tool to another. Programming such a reader requires knowledge of the file format that is being read as well as the equations necessary to obtain the derived values after loading. When running these CFD simulations, extremely large files are being loaded and having values being calculated. These simulations usually take a few hours to complete, even on the fastest machines. Graphics processing units (GPUs) are usually used to load the graphics for computers; however, in recent years, GPUs are being used for more generic applications because of the speed of these processors. Applications run on GPUs have been known to run up to forty times faster than they would on normal central processing units (CPUs). If these CFD programs are extended to run on GPUs, the amount of time they would require to complete would be much less. This would allow more simulations to be run in the same amount of time and possibly perform more complex computations.
Chawner, David M.↗
Comparison of volatiles evolving from selected highland and mare lunar regolith simulants during vacuum sintering
Volatiles evolving from JSC-1A, NU-LHT-4M and CSM-LHT-1G lunar regolith simulants during in vacuo thermal processing were analyzed using mass spectrometry as a function of temperature. Two high-fidelity simulants, JSC-1A (mare) and NU-LHT-4M (highland), were compared to a newly developed CSM-LHT-1G highland simulant, modified to closely match lunar geochemistry. Large autogenous gas loads were observed for all investigated materials. Mineralogical knowledge was used to identify and attribute individual volatile species to reacting, transforming, or decomposing constituents (hydrates, carbonates, sulfates, sulfides, clays, etc.) of the respective regolith simulant in the self-generated gas environment. Cumulative mass losses for individual simulant components as a function of temperature were quantified using mass spectrometry in conjunction with thermogravimetric analysis. Investigation of the four components of CSM-LHT-1G – anorthosite, basalt, augite, and glass – aided the attribution of volatile species to specific compounds and their respective sources. The results showed significant decomposition of non-lunar phases present in the man-made regolith simulants below the typical glass crystallization temperatures, which paves the way to devising methods for enhancing the fidelity of the simulants. Finally, high gas loads and corrosive gases (HF and HCl) were recognized as potential hazards, pertaining to the development of large testbed facilities.
42 ENGINEERING↗