Search NASA⌕ Search

SEARCH · Search NASA

Results for “Martensite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A Mechanism for Carbon Depletion at Bondline of High-Frequency Electric-Resistance-Welded X70 Pipeline Steel

The bondline of electric-resistance-welded (ERW) linepipe steel, often etched white (i.e., ferrite) in optical microscopy, is generally believed to be carbon depleted. The mechanism for the carbon depletion, however, is not fully understood by researchers. To this end, here we used atom probe tomography (APT) to measure elemental segregation of the as-welded and post-weld heat-treated bondline regions of X70 linepipe welds. The thin vertical features at the bondline in the as-welded condition were identified as carbon-rich martensite-austenite (M-A) constituents, and the majority ferrite phase in the bondline was identified as carbon-depleted ferrite. Following the post-weld normalization, all alloying elements, except Nb and Mo, are homogenized across the bondline and heat-affected zone. The carbon depletion in the ERW bondline was accurately measured. A new mechanism for carbon depletion has been proposed using Scheil calculations of elemental partitioning during weld formation. Segregation of elements in the heat-affected zone was shown to follow the negligible partitioning local equilibrium (NPLE) kinetics for bainite transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Manipulating Retained Austenite Fraction and Stability With Controlled Chemical Heterogeneities in Q&P Steels

Advanced high-strength steels go through complex heat treatment processes with the goal of retaining austenite to enhance the mechanical properties. Martensite start temperature predictions are generally based on bulk composition when designing heat treatments, so compositional heterogeneities are not considered. Here, the effects of compositional heterogeneities on retained austenite fractions in a quenching and partitioning steel are investigated. In conclusion, the results show that Mn banding from solidification can be used to change retained austenite fractions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Insights into the Transformation-Induced Plasticity (TRIP) Effect in Ti-Free Grade 300 Maraging Steel Manufactured by Laser Powder Bed Fusion (LPBF)

The near-net fabrication capabilities of laser powder-bed fusion (LPBF) offer the potential to manufacture tools with complex cooling channels that can improve the production efficiency of the tools with reduced greenhouse gas emissions. High strength, toughness, and wear resistance are some of the key properties required by the tooling industries to qualify tools. While strength can be increased through appropriate heat treatments, the increase in strength comes with an associated ductility loss. Here, we show that the non-equilibrium conditions inherent to LPBF can suppress the transformation-induced plasticity effect to room temperature in a Ti-free version of grade 300 maraging steel (G300MS), which is commonly not observed at room temperature in G300MS manufactured using conventional methods. The presence of retained austenite along with Ni-rich regions was found to increase the kinetics for austenite reversion during aging, thereby enabling the transformation of austenite into ε martensite during tensile deformation at room temperature, in turn increasing the strength with minimal ductility loss.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-Throughput Nanoindentation Mapping of Additively Manufactured T91 Steel

Here, this work aims to adapt nanoindentation mapping combined with a k-means algorithm as a high-throughput technique to study the nano-scale spatial changes in mechanical properties for a heterogeneous material. This technique can also classify the individual data points based on their properties. Hundreds to thousands of indents were performed on additively manufactured T91 at room temperature, 300°C, 400°C, and 500°C across a square area with a side length of 120 μm to 400 μm. From this data, the hardness and reduced modulus at each point could be calculated and mapped. Using k-means clustering, we were able to arrange the data into three or four clusters corresponding roughly to the ferritic and martensitic phases as well as one or two intermediate clusters sampling both the phases. The hardness of these two phases appears to be quite stable as a function of temperature. Nanoindentation mapping and the k-means algorithm can therefore be used to rapidly assess the feasibility of heterogeneous materials under extreme conditions, such as nuclear reactor steels.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Assessment of Outliers in Alloy Datasets Using Unsupervised Techniques

We report advancements in data analytics techniques have enabled complex, disparate datasets to be leveraged for alloy design. Identifying outliers in a dataset can reduce noise, identify erroneous and/or anomalous records, prevent overfitting, and improve model assessment and optimization. In this work, two alloy datasets (9-12% Cr ferritic martensitic steels, and austenitic stainless steels) have been assessed for outliers using unsupervised techniques and supplemented with domain knowledge. Principal component analysis and k-means clustering were applied to the data, and points were assessed as outliers based on their distance away from other points in the cluster and from other points in the dataset. The outlier characteristics were investigated to determine both cluster-specific and overall trends in the properties of the outlier points. The approach demonstrated here is extensible to other alloy datasets for outlier identification and evaluation to improve the reliability of machine learning and modeling predictions for advanced alloy design.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ion Implantation-Induced Plastic Phenomena in Metallic Alloys

Ion implantation is widely used for doping semiconductors or electroceramic materials and probing material behaviors in extreme radiation environments. However, implanted ions can induce compressive stresses into the host material, which can induce plasticity and mesoscopic deformation. However, these phenomena have almost exclusively been observed in brittle ionic and/or covalently bonded materials. Here, in this study, we present transmission electron microscopy observations of unusual implantation-induced plasticity in two metallic alloys. First, Fe 2+ ions induce dislocation plasticity below the implanted layer in a model Fe-P alloy. Next, He+ ions form pressurized cavities which activate the fcc-to-hcp strain-induced martensitic transformation in Alloy 625. In both cases, the plasticity can be explained by a combination of implanted ions being incorporated into the lattice and the creation of irradiation defects. These findings have significant implications for mechanical testing of ion-implanted layers, while also opening pathways for using ion implantation to tune stress distributions in metallic alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Comparative Mechanical Properties Analysis of Triple Ion-Beam Irradiated and Neutron Irradiated Potential Plasma Facing Components

Abstract Several classes of materials are being proposed for use in fusion reactors including oxide dispersion strengthened (ODS) and reduced activation ferritic-martensitic (RAF/M) steels to withstand the severe and harsh conditions. In this work, the mechanical properties of a Fe-16Cr-4Al-2W-0.3Ti-0.3Y 2 O 3 (K3) (ODS) ferritic steel and a Fe-8.9Cr-1.1W-0.47Mn-0.2V-0.14Ta-0.11C (Eurofer 97) (RAF/M) steel) after triple ion beam irradiation were locally evaluated utilizing in-situ micro-pillar compression tests, and continuous stiffness/quasi-static nanoindentation. No change in mechanical properties was observed in the K3 ODS steel. However, the Eurofer 97 RAF/M steel exhibited radiation-induced effects via increases in yield strength. Micro-pillar techniques were expanded to neutron-irradiated materials via an in-situ testing technique employing lift-out methods on Fe-14Cr-0.9Ti-0.3Mo-0.25Y 2 O 3 (MA957) ODS ferritic steel. Both the non-irradiated and irradiated compressive yield stresses of the MA 957 micro-pillars were in good agreement with bulk yield stress values reported in the literature, suggesting that the lift-out micro-pillar compression testing technique is a promising method. The demonstration of these techniques on ion beam and neutron irradiated ODS steels and ion beam RAF/M steels gives information to inform models of the material degradation during use in a fusion device.

alloys↗
DOE OSTI2020

Irradiation Creep in Materials

A knowledge of the dimensional stability of reactor structural components, under irradiation conditions, is of major importance in the design of thermal, fast, and fusion reactors. When subjected to simultaneous mechanical loading and irradiation, structural materials exhibit a visco-plastic deformation phenomenon, referred to as irradiation creep, which can be more rapid than the deformation occurring out of irradiation. In this article, the phenomenology of this peculiar behavior is described after a short history of its discovery. Then, the theoretical mechanisms proposed in the literature during these past 60 years are presented, with a special focus on mechanisms based on stress induced preferred absorption of point defects by dislocation loops, dislocations and grain boundaries and on mechanisms based on climb-enhanced glide of dislocations. These mechanisms are discussed in the light of experimental evidences. Finally, irradiation creep in various materials, such as zirconium alloys, austenitic stainless steels, nickel-based alloys, ferritic-martensitic steels and graphite, is described.

Onimus, Fabien↗
DOE OSTI2020

Effect of heat treatment on the tensile behavior of selective laser melted Ti-6Al-4V by in situ X-ray characterization

Selective Laser Melted Ti-6Al-4V (as-SLMed) exhibits decreased yield strength, increased work hardening, and increased ductility after heat treatment at 730 degrees C (HT-730) or 900 degrees C (HT-900) for 2 h. To understand the change of mechanical properties, in situ high energy X-ray diffraction (HEXRD) is used to examine the phase composition, load partitioning, slip system activity, and dislocation density evolution in all three specimens. The as-SLMed specimen is dominated by martensitic α'. After heat treatment, α' partly or fully decomposes into α+β, reducing the yield strength. In HT-730, beta precipitates with confined size show much higher lattice strain than the α'/α matrix during deformation; in HT-900, the lattice strain difference is mostly eliminated. This is a key reason for the increased ductility in HT-900. From the anisotropic lattice strain development, basal slip is identified as the easiest slip system in α'/α. Using an elasto-plastic self-consistent (EPSC) model, the critical resolved shear stress ratio between prismatic slip and basal slip (CRSS prism /CRSS basal ) is estimated to be 1.31 and 1.16 in the as -SLMed and the HT-900 specimens, respectively. Further, the alpha phase in HT-900 is able to activate multiple slip systems and accumulate more dislocations during plastic deformation. This explains why HT-900 has better ductility and higher work hardening rate than the other two specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Temperature-dependent cavity swelling in dual-ion irradiated Fe and Fe-Cr ferritic alloys

Fe-Cr ferritic-martensitic (FM) steels are promising structural material candidates for fusion and advanced fission reactors due to their attractive mechanical properties and volumetric swelling resistance. However, significant discrepancies exist regarding the effect of solutes and irradiation temperature on cavity swelling under ion versus neutron irradiation conditions. In this study, simultaneous dual ion irradiations (8 MeV Ni 3+ ions and energy-degraded 3.5 MeV He 2+ ions) were used to quantify the cavity swelling behavior in ultra-high purity Fe and Fe-Cr alloys (3-14 wt.% Cr), Fe-10 wt.% Cr-780 wt.ppm C, and Eurofer97 FM steel. The irradiations were conducted over a wide temperature range (400-550°C) with a mid-range dose of ~30 displacements per atom (dpa) and 0.1 appm/dpa He implantation rate. Here, using state-of-the-art transmission electron microscopy (TEM), we reveal that pure Fe has a ~50°C lower peak swelling temperature difference than Fe-Cr alloys, which is attributed to higher vacancy mobility in pure Fe. Chromium solute appears to strongly suppress cavity swelling in Fe-Cr alloys for temperatures below ~470°C, but seems to have little effect or slightly enhances swelling above ~470°C. Cavities were observed in all the irradiated samples between 400-550°C. This indicates that the narrow temperature range of observable cavities reported in prior ion irradiated Fe-Cr ferritic alloy studies is likely an artifact associated with the use of low ion energies (<5 MeV), which leads to pronounced near-surface and implanted ion effects that suppress cavity swelling even at midrange depths (particularly at high temperatures).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Origin, parameters, and underlying deformation mechanisms of propagating deformation bands in irradiated 316L stainless steel

Lüders-type propagating deformation bands were observed in specimens of irradiated 316L stainless steel samples removed from Spallation Neutron Source target vessels after service. Mechanical testing with digital image correlation (DIC) and in-situ tensile testing with scanning electron microscopy electron backscatter diffraction showed that the observed Lüders-type behavior was not related to the known transformation-induced plasticity or twinning-induced plasticity behavior. Instead, the phenomenon occurs at small local strain values before a significant amount of martensite or deformation twins appear in the microstructure. Microstructural analysis and in-situ mechanical test results suggest Lüders-type band formation and propagation were related to the appearance and evolution of defect-free channels—analogous to slip bands. A modified Swift equation with a Ludwigson-like component was offered to rationalize the phenomenon and model the strain-softening processes at small strain values. Finally, the results indicate complex microstructural processes and deformation mechanisms were active at small strain values and underline the benefits of advanced mechanical test approaches such as DIC.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High-pressure phase transitions in a laser directed energy deposited Fe-33Cu Alloy

Here, additively manufactured Fe-Cu alloys contain both equilibrium face-centered cubic (FCC) and metastable body-centered cubic (BCC) crystal structure Cu precipitates depending on their size. However, the stability of these nanoscale precipitates under extreme conditions such as high pressures has not been reported. This study investigates the phase transformations and microstructural stability of laser directed energy deposition (DED-LB) made Fe67Cu33 alloy (nominal composition in at.%) under high static pressure deformation using in-situ synchrotron X-ray diffraction under pressure, postmortem high-resolution scanning transmission electron microscopy (HR-STEM), and molecular dynamics (MD) simulations. In-situ XRD results reveal a reversible phase transformation from BCC to the hexagonal close-packed (HCP) structure in the Fe grains at an onset pressure of 16.4 GPa, significantly higher than reported in the literature for pure Fe. Although no high-pressure phase transition was observed in the FCC Cu grains through XRD, HR-STEM analysis uncovers a phase transition to the HCP structure in nanoscale metastable BCC Cu precipitates within the BCC Fe matrix. After decompression, the Fe matrix reverted back to the BCC structure with periodic lath martensite, while regions of the nanoscale BCC Cu precipitates retained the metastable HCP structure. MD simulations support the BCC → HCP transition in the embedded nanoscale coherent Cu precipitates, consistent with the classical Burgers mechanism. Thus, by leveraging in-situ XRD observation, postmortem high-resolution S/TEM microscopy, and MD simulations, this study offers profound insights into the distinctive phase transformations induced by high pressure in DED-LB Fe67Cu33 alloy, which is distinguished by its hierarchical microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Decoding anomalous grain growth at room temperature during pressure-induced phase transformations

Significant grain growth is observed during the high-pressure phase transformations (PTs) at room temperature in various materials. The main focus here is grain growth from a few hundred nanometers to 10 μm within an hour during α → ω PT in Zr. No existing theory explains this phenomenon since without PT, Zr nanocrystals do not grow at room temperature even for up to 10 years. Here, in this study, a multistep mechanism for the grain growth during α → ω PT in Zr is suggested. Phase interfaces (PI) and grain boundaries (GBs) coincide and move together as a combined PI-GBs under the action of the combined thermodynamic driving force. Such a combined motion changes the diffusional grain growth mechanism to the transformational one and the martensitic mechanism of PT to a reconstructive one via an intermediate disordered phase. The primary condition is that the GB energy of the ω phase is smaller than that of the α phase, which promotes the nucleation of ω-Zr and is consistent with the absence of the reverse PT and reduction in the PT pressure with reducing grain size. Several intermediate steps for such motion are suggested and justified kinetically. Nonhydrostatic stresses due to volume reduction in the growing ω grain promote continuous growth of the existing ω grain instead of a new nucleation at other GBs. In situ synchrotron Laue diffraction experiments confirm the main predictions of the theory. The suggested mechanism provides a new insight into synergistic interaction between PTs and microstructure evolution.

anomalous grain growth during phase transformation↗
DOE OSTI2026

Ultra-grain refinement creates FCC pure cobalt with high strength and high ductility

Although pure cobalt is generally known to have a hexagonal close-packed (HCP) structure at room temperature, we show that its high-temperature face-centered cubic (FCC) phase can be strongly stabilized through grain refinement, resulting in FCC pure cobalt at room temperature. Ultrafine-grained (UFG) FCC cobalt exhibits a hierarchical microstructure consisting of dense stacking fault (SF) networks in the dominant FCC grains and numerous SFs and thin FCC layers within a few HCP plates. This unique microstructure leads to a high tensile strength exceeding 1 GPa, together with a tensile elongation of over 35%, thereby surpassing the well-known strength–ductility trade-off of pure metals. In-situ synchrotron X-ray diffraction revealed that the UFG FCC cobalt exhibited a markedly enhanced deformation-induced FCC→HCP martensitic transformation, which provided sustained strain hardening through the transformation-induced plasticity (TRIP) effect. Furthermore, ultra-grain refinement dramatically suppressed premature void and crack formation, causing a transition in the fracture mode from brittle to ductile. These findings advance the fundamental understanding of the phase stability and TRIP-assisted deformation in elemental cobalt and offer new guidelines for the microstructure-driven design of high-performance cobalt-based structural alloys.

Metastability↗
DOE OSTI2025

Microstructure-sensitive mechanical behavior of an additively manufactured psuedoelastic shape memory alloy

The additive manufacturing of shape memory alloys into complex geometries enables fabrication of advanced functional systems across a variety of fields and domains. This work presents results focused on the mechanical behavior of additively manufactured shape memory pseudoelastic NiTi. The deformation induced solid state phase transformation from austenite to martensite allows this system to accommodate large recoverable strains. This deformation behavior is fundamentally driven by crystal-scale transformation physics. Laser powder bed fusion processing reveals that the resulting microstructure, both grain morphology and crystallographic texture, is strongly dependent on the manufacturing processing history. Exhaustive mechanical testing demonstrates that these microstructural factors strongly impact both tensile and cyclic stress–strain behavior. Cyclic dissipative behavior, however, is similar across all tested microstructures following an initial transient period. Remarkably, analysis of spatial strain fields during tensile loading reveals two distinctly different localization “modes”. The first is initiation of localized deformation bands which continuously propagate through the tensile bar during loading. In the second mode localization is observed but lacks propagation; instead additional localization cites nucleate during subsequent loading. The latter phenomena is suspected to be driven by grain-scale deformation physics as the localized band morphologies coincide with grain morphologies. These phenomena strongly impact the resulting aggregate stress–strain behavior. Hence, manufacturers and designers of psuedoelastic functional components must at the very least consider the potential variability in properties when considering additive manufacturing processing. More ideally the process–structure–property relations can be used to further tailor and optimize final functional performance.

Additive manufacturing↗
DOE OSTI2021

Consumable development to tailor residual stress in parts fabricated using directed energy deposition processes

Distortion and residual stresses are major challenges that limit the ability to fabricate large scale structures using Additive Manufacturing (AM). Researchers worldwide are evaluating techniques to induce compressive residual stress in the parts via intermittent rolling. While reasonable success has been documented, the idea of lowering the martensite start temperature to induce compressive stresses has not been evaluated in the context of AM, despite demonstrated success by the welding community. This study validates the hypothesis that, by a proper selection of materials and process parameters, one may effectively reduce distortion and induce a compressive residual stress in AM parts. Using neutron diffraction to measure residual stresses in parts, we demonstrate that, in addition to selection of the correct materials, the inter pass temperature plays a major role in controlling the residual stress evolution. The observations relating to the residual stresses are rationalized based on a microstructural evolution in these samples. Based on this preliminary study, a strategy to fabricate large structures with minimal distortion and residual stress is outlined.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Developing ductile and isotropic Ti alloy with tailored composition for laser powder bed fusion

Laser powder bed fusion (LPBF) is an advanced technology to create metallic components with complex geometry. Ti-6Al-4V (Ti64) is one of the most frequently used materials for LPBF. The intrinsic high cooling rates and ultra-high directional thermal gradient of melt, however, lead to a hierarchical structure composed of fine martensitic alpha' within columnar prior-beta grains in LPBF Ti64. This microstructure results in poor ductility and strong mechanical anisotropy in as-built Ti64 components, which largely limit their applications. Here, we report that the above shortcomings can be overcome by tailoring the alloy composition. Specifically, by reducing the aluminum content from 6 wt% to 4 wt%, the resultant LPBF Ti-4Al-4V (Ti44) alloy exhibits substantially improved ductility and mechanical isotropy. These improvements are attributed to grain refinement during solidification and the activation of multiple slip modes and twinning in the as-built material during deformation. This work offers a simple strategy to design new titanium alloys for LPBF with significantly improved ductility and isotropy.

36 MATERIALS SCIENCE↗