Results for “Model Reference Control” — Page 20

NASA NTRS2009

Adaptive Control of a Transport Aircraft Using Differential Thrust

The paper presents an adaptive control technique for a damaged large transport aircraft subject to unknown atmospheric disturbances such as wind gust or turbulence. It is assumed that the damage results in vertical tail loss with no rudder authority, which is replaced with a differential thrust input. The proposed technique uses the adaptive prediction based control design in conjunction with the time scale separation principle, based on the singular perturbation theory. The application of later is necessitated by the fact that the engine response to a throttle command is substantially slow that the angular rate dynamics of the aircraft. It is shown that this control technique guarantees the stability of the closed-loop system and the tracking of a given reference model. The simulation example shows the benefits of the approach.

Stepanyan, Vahram↗

NASA NTRS1999

Preliminary Results of the 1.5% TCA (Modular) Controls Model in the NASA Langley UPWT

To summarize the significant highlights in this report: (1) Data quality, determined by multiple repeat runs performed on the TCA baseline configuration, and long-term repeatability, determined by comparing baseline Reference H data from this test to a previous test, have been shown to be good. (2) The longitudinal stability of the TCA is more non-linear than for the Reference H, and while it is similar at normal lift values, the TCA has considerably more pitch-up at higher lift. (3) Longitudinal control effectiveness of the TCA is similar to the Reference H and the ratio of elevator effectiveness to horizontal tail effectiveness is approximately 0.3. 4) The directional stability of the TCA is improved relative to Reference H at higher angles-of attack. The chine is effective for improving directional stability. (5) The directional control effectiveness 'of the TCA rudder is the same as that of the Reference H rudder at low angles-of-attack, after taking factors, such as number of rudder panels deflected and vertical tail volume into account. However, rudder effectiveness was shown to be reduced at higher angles-of-attack. (6) The lateral stability was shown to be reduced relative to the Reference H, which may be beneficial at low speeds for alleviating lateral control saturation. (7) Lateral control effectiveness for the TCA was shown to be similar to the Reference H for negative trailing-edge flap deflections and was reduced by approximately 25% for positive trailing-edge flap deflections.

Kubiatko, Paul↗

NASA NTRS1999

Preliminary Results of the 1.5% TCA (Modular) Controls Model in the NASA Langley UPWT

To summarize the significant highlights in this report: (1) Data quality, determined by multiple repeat runs performed on the TCA baseline configuration, and long-term repeatability, determined by comparing baseline Reference H data from this test to a previous test, have been shown to be good. (2) The longitudinal stability of the TCA is more non-linear than for the Reference H, and while it is similar at normal lift values, the TCA has considerably more pitch-up at higher lift. (3) Longitudinal control effectiveness of the TCA is similar to the Reference H and the ratio of elevator effectiveness to horizontal tail effectiveness is approximately 0.3. (4) The directional stability of the TCA is improved relative to Reference H at higher angles-of attack. The chine is effective for improving directional stability.

Kubiatko, Paul↗

NASA NTRS1993

System identification of the Large-Angle Magnetic Suspension Test Facility (LAMSTF)

The Large-Angle Magnetic Suspension Test Facility (LAMSTF), a laboratory-scale research project to demonstrate the magnetic suspension of objects over wide ranges of attitudes, has been developed. This system represents a scaled model of a planned Large-Gap Magnetic Suspension System (LGMSS). The LAMSTF system consists of a planar array of five copper electromagnets which actively suspend a small cylindrical permanent magnet. The cylinder is a rigid body and can be controlled to move in five independent degrees of freedom. Five position variables are sensed indirectly by using infra-red light-emitting diodes and light-receiving phototransistors. The motion of the suspended cylinder is in general nonlinear and hence only the linear, time-invariant perturbed motion about an equilibrium state is considered. One of the main challenges in this project is the control of the suspended element over a wide range of orientations. An accurate dynamic model plans an essential role in controller design. The analytical model of the LAMSTF system includes highly unstable real poles (about 10 Hz) and low-frequency flexible modes (about 0.16 Hz). Projection filters are proposed to identify the state space model from closed-loop test data in time domain. A canonical transformation matrix is also derived to transform the identified state space model into the physical coordinate. The LAMSTF system is stabilized by using a linear quadratic regulator (LQR) feedback controller. The rate information is obtained by calculating the back difference of the sensed position signals. The reference inputs contain five uncorrelated random signals. This control input and the system reponse are recorded as input/output data to identify the system directly from the projection filters. The sampling time is 4 ms and the model is fairly accurate in predicting the step responses for different controllers while the analytical model has a deficiency in the pitch axis.

Huang, Jen-Kuang↗

NASA NTRS1986

Analytical investigation of the dynamics of tethered constellations in Earth orbit, phase 2

The development of a two dimensional analytical model that describes the dynamics of an n-mass vertical tethered system is reported. Two different approaches are described: in the first one the control quantities are the independent variables while in the second one the Cartesian coordinates of each mass expressed in the orbiting reference frame are the independent variables. The latter model was used in the 3-mass version to simulate the dynamics of the tethered system in applications involving the displacement of the middle mass along the tether. In particular, issues related to reproducing predetermined acceleration profiles and g-tuning are reported.

Lorenzini, E.↗

NASA NTRS2023

Thermomechanical Real-Time Hybrid Simulation: Conceptual Framework and Control Requirements

Real-time hybrid simulation (RTHS) is an enabling technology that has transformed engineering experimentation and helped researchers expand modeling capabilities. However, breakthroughs are necessary to expand the range of hybrid simulation methods and, thus, enable experiments with loading conditions representing multiple hazards. This paper discusses the development of a new thermomechanical RTHS framework and a systematic approach to determining RTHS control requirements. First, the framework is established using a representative finite element model of a layered structural system subjected to thermal loading. A complete two-layer system model serves as the reference system, and it is then partitioned into a numerical layer and an experimental layer that share interface conditions. Next, a thermal actuator is introduced to impose dynamic thermal loading on the experimental subsystem, serving as a transfer system. Finally, control and performance metrics are defined to evaluate the realization of interface boundary conditions and map this to the RTHS execution. Through an illustrative example considering the influence of temperature on a lunar habitat, we demonstrate how to establish controller requirements for RTHS and demonstrate that this approach can be used to conduct RTHS on structures with thermomechanical loading.

Herta Montoya↗

NASA NTRS2018

ST7 Disturbance Reduction System (DRS) Colloid Micronewton Thruster Performance and Control Algorithm Model Simulation Validation in Flight

Colloid Micronewton Thrusters (CMNT) were flight demonstrated for the first time on the ST7Disturbance Reduction System (DRS) payload on the European Space Agency (ESA) Laser Interferometer Space Antenna (LISA) Pathfinder spacecraft for attitude and drag-free spacecraft control. LISA Pathfinder was a technology demonstration mission for ESA’s LISA gravitational wave observatory, currently in Phase A with a launch date of 2034. The DRS included the Integrated Avionics Unit (IAU), eight Colloid Micronewton Thrusters (CMNT), Dynamic Control Software (DCS) and Flight Software (FSW). The CMNT technology met performance requirements operating at 5-30 µN of thrust with ≤0.1 µN resolution and ≤0.1 µN/Hz thrust noise to deliver the required nanometer-level precision spacecraft control measured by the gravitational reference sensor (GRS) in the ESA LISA Technology Package (LTP). The performance of seven of the CMNT in flight was consistent with ground test results. The colloid thruster performance model of thrust and thrust noise as a function of operational parameters (i.e. beam current, voltage, temperature, etc.) was validated in flight over a wide range of conditions. A model and simulation of the thruster control algorithm was developed and validated with flight data to predict thrust noise. This capability is important because it is considered to be a significant source of position noise on the spacecraft and, therefore, the acceleration noise on the test masses, which provide the gravity wave measurements. The CMNT thruster model data and validation with LISA Pathfinder/ST7-DRS flight experiments are discussed in this paper.

Hruby, Vlad↗

NASA NTRS1988

A brief review on the identification of nonlinear mechanical systems

This paper presents a brief review of the disciplines used in the identification of nonlinear mechanical systems, including the detection of nonlinearities and their quantification, and parameter estimation. Techniques for determining the parameters of nonlinear system models with assumed model form are described and briefly discussed. Recent developments in identifying system models which may contain the actual model forms as well as incorrect forms is also briefly described. A list of representative references from structures and control disciplines is given.

Natke, H. G.↗

NASA NTRS1988

The inclusion of semi-Markov reconfiguration transitions into the computer-aided Markov evaluator (CAME) program

The modifications to the rule-based CAME program which allow it to more accurately model the fault-handling processes of fault-tolerant systems are described. This new capability is added to the CAME program by modeling the fault-handling processes of fault-tolerant systems. The integrated airframe/propulsion control system architecture (IAPSA II) reference configuration currently under development is detailed.

Rosch, Gene↗

NASA NTRSDate not supplied

Utilizing Advanced Air Mobility Rotorcraft Tools for Wildfire Applications

Over the past decade, due in large part to heavy investment in the field of Advanced Air Mobility (AAM), significant progress in rotorcraft-focused modeling tools has been made. Such progress has notably increased AAM rotorcraft modeling capabilities in the topics of conceptual design, preliminary design, and more recently flight dynamics. Yet, due to recent and persistent increases in extreme weather events, an emerging interest has been raised in utilizing such modeling capabilities for aiding in emergency relief efforts and other public good missions. This paper uses wildfire fighting as a representative public good mission and demonstrates the relevance of the NASA Revolutionary Vertical Lift Technology (RVLT) rotorcraft toolchain to such missions. An emphasis is placed on flight dynamics modeling and control because of the hazards and challenges associated with the atmospheric environment of wildfires. In this work, the NASA FlightCODE tool was used to analyze both a UH-60 and the NASA six-passenger quadcopter reference model hovering in an experimentally informed wildfire turbulent environment. Preliminary results of this study estimate actuator usage exceedances and disturbance rejection capabilities of the vehicles’ translational rate command systems. Leveraging the RVLT toolchain, refinement and expansion of this work could lead to handling qualities envelope estimation and design optimization for wildfire turbulent environments. This would provide pilots with additional information to make real-time decisions in high-risk scenarios and begins preparations for simulating these dangerous environments for pilot training and experimentation.

Rotorcraft↗

NASA NTRSDate not supplied

Utilizing Advanced Air Mobility Rotorcraft Tools for Wildfire Applications

Over the past decade, due in large part to heavy investment in the field of Advanced Air Mobility (AAM), significant progress in rotorcraft-focused modeling tools has been made. Such progress has notably increased AAM rotorcraft modeling capabilities in the topics of conceptual design, preliminary design, and more recently flight dynamics. Yet, due to recent and persistent increases in extreme weather events, an emerging interest has been raised in utilizing such modeling capabilities for aiding in emergency relief efforts and other public good missions. This paper uses wildfire fighting as a representative public good mission and demonstrates the relevance of the NASA Revolutionary Vertical Lift Technology (RVLT) rotorcraft toolchain to such missions. An emphasis is placed on flight dynamics modeling and control because of the hazards and challenges associated with the atmospheric environment of wildfires. In this work, the NASA FlightCODE tool was used to analyze both a UH-60 and the NASA six-passenger quadcopter reference model hovering in an experimentally informed wildfire turbulent environment. Preliminary results of this study estimate actuator usage exceedances and disturbance rejection capabilities of the vehicles’ translational rate command systems. Leveraging the RVLT toolchain, refinement and expansion of this work could lead to handling qualities envelope estimation and design optimization for wildfire turbulent environments. This would provide pilots with additional information to make real-time decisions in high-risk scenarios and begins preparations for simulating these dangerous environments for pilot training and experimentation.

Rotorcraft↗

NASA NTRS1976

FLEXSTAB: A computer program for the prediction of loads and stability and control of flexible aircraft

Capabilities of the FLEXSTAB Computer Program System are described and illustrated. Aeroelastic analysis of a wide variety of aircraft configurations is performed. The aerodynamic theory used in FLEXSTAB is applicable to both steady and unsteady, subsonic and supersonic flow for multiple wing-body tail nacelle configurations with a plane of symmetry. For unsteady flow calculations, an unsteady aerodynamic theory is used which is appropriate for the low reduced frequencies associated with aircraft flight dynamics. The aircraft is modeled as either a rigid or flexible structure. The computer trims the aircraft in steady reference flight and computes both static and dynamic stability and control derivatives and the stability behavior about the trim condition. The airplane lifting pressure distribution, aerodynamic and inertia loads and deflected shape are also computed.

Perkin, B. R.↗

NASA NTRS1987

Dynamic and attitude control characteristics of an International Space Station

The structural dynamic characteristics of the International Space Station (ISS), the interim reference configuration established for NASA's Space Station developmental program, are discussed, and a finite element model is described. Modes and frequencies of the station below 2.0 Hz are derived, and the dynamic response of the station is simulated for an external impulse load corresponding to a failed shuttle-docking maneuver. A three-axis attitude control system regulates the ISS orientation, with control moment gyros responding to attitude and attitude rate signals. No instabilities were found in the attitude control system.

Sutter, Thomas R.↗

NASA NTRS2014

A Modular Approach to Model Oscillating Control Surfaces Using Navier Stokes Equations

The use of active controls for rotorcraft is becoming more important for modern aerospace configurations. Efforts to reduce the vibrations of helicopter blades with use of active-controls are in progress. Modeling oscillating control surfaces using the linear aerodynamics theory is well established. However, higher-fidelity methods are needed to account for nonlinear effects, such as those that occur in transonic flow. The aeroelastic responses of a wing with an oscillating control surface, computed using the transonic small perturbation (TSP) theory, have been shown to cause important transonic flow effects such as a reversal of control surface effectiveness that occurs as the shock wave crosses the hinge line. In order to account for flow complexities such as blade-vortex interactions of rotor blades higher-fidelity methods based on the Navier-Stokes equations are used. Reference 6 presents a procedure that uses the Navier-Stokes equations with moving-sheared grids and demonstrates up to 8 degrees of control-surface amplitude, using a single grid. Later, this procedure was extended to accommodate larger amplitudes, based on sliding grid zones. The sheared grid method implemented in EulerlNavier-Stokes-based aeroelastic code ENS AERO was successfully applied to active control design by industry. Recently there are several papers that present results for oscillating control surface using Reynolds Averaged Navier-Stokes (RANS) equations. References 9 and 10 report 2-D cases by filling gaps with overset grids. Reference 9 compares integrated forces with the experiment at low oscillating frequencies whereas Ref. 10 reports parametric studies but with no validation. Reference II reports results for a 3D case by modeling the gap region with a deformed grid and compares force results with the experiment only at the mid-span of flap. In Ref. II grid is deformed to match the control surface deflections at the section where the measurements are made. However, there is no indication in Ref. II that the gaps are explicitly modeled as in Ref. 6. Computations using overset grids are reported in Ref. 12 for a case by adding moving control surface to an existing blade but with no validation either with an experiment or another computation.

Navier↗

NASA NTRS1993

Gyroless yaw control system for a three axis stabilized, zero-momentum spacecraft

A satellite attitude control system is usable in the absence of any inertial yaw attitude reference, such as a gyroscope, and in the absence of a pitch bias momentum. Both the roll-yaw rigid body dynamics and the roll-yaw orbit kinematics are modelled. Pitch and roll attitude control are conventional. The model receives inputs from a roll sensor, and roll and yaw torques from reaction wheel monitors. The model produces estimated yaw which controls the spacecraft yaw attitude.

Stetson, Jr., John B.↗

NASA NTRS2015

ISS-CREAM Thermal and Fluid System Design and Analysis

Thermal and Fluids Analysis Workshop (TFAWS), Silver Spring MD NCTS 21070-15. The ISS-CREAM (Cosmic Ray Energetics And Mass for the International Space Station) payload is being developed by an international team and will provide significant cosmic ray characterization over a long time frame. Cold fluid provided by the ISS Exposed Facility (EF) is the primary means of cooling for 5 science instruments and over 7 electronics boxes. Thermal fluid integrated design and analysis was performed for CREAM using a Thermal Desktop model. This presentation will provide some specific design and modeling examples from the fluid cooling system, complex SCD (Silicon Charge Detector) and calorimeter hardware, and integrated payload and ISS level modeling. Features of Thermal Desktop such as CAD simplification, meshing of complex hardware, External References (Xrefs), and FloCAD modeling will be discussed.

Thermal analysis↗

NASA NTRS2002

Hindlimb unloading rodent model: technical aspects

Since its inception at the National Aeronautics and Space Administration (NASA) Ames Research Center in the mid-1970s, many laboratories around the world have used the rat hindlimb unloading model to simulate weightlessness and to study various aspects of musculoskeletal loading. In this model, the hindlimbs of rodents are elevated to produce a 30 degrees head-down tilt, which results in a cephalad fluid shift and avoids weightbearing by the hindquarters. Although several reviews have described scientific results obtained with this model, this is the first review to focus on the technical aspects of hindlimb unloading. This review includes a history of the technique, a brief comparison with spaceflight data, technical details, extension of the model to mice, and other important technical considerations (e.g., housing, room temperature, unloading angle, the potential need for multiple control groups, age, body weight, the use of the forelimb tissues as internal controls, and when to remove animals from experiments). This paper is intended as a reference for researchers, reviewers of manuscripts, and institutional animal care and use committees. Over 800 references, related to the hindlimb unloading model, can be accessed via the electronic version of this article.

NASA Discipline Musculoskeletal↗

NASA NTRS1972

Adaptive control and identification via Liapunov's direct method.

The adaptive control and identification problems for single input, single output, time invariant systems with unknown parameters are considered here. A model reference is used and Liapunov's direct method provides the mechanisms for deriving the adaptive and identification algorithms. The Kalman Lemma (derived in connection with the Lure' problem) is shown to be extremely helpful in the design of these systems.

Monopoli, R. V.↗