Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLASMA LAYER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Demonstration of Separation Delay with Glow-Discharge Plasma Actuators

Active flow control of boundary-layer separation using glow-discharge plasma actuators is studied experimentally. Separation is induced on a flat plate installed in a closed-circuit wind tunnel by a shaped insert on the opposite wall. The flow conditions represent flow over the suction surface of a modern low-pressure-turbine airfoil. The Reynolds number, based on wetted plate length and nominal exit velocity, is varied from 50,000 to 300,000, covering cruise to takeoff conditions. Low (0.2 percent) and high (2.5 percent) free-stream turbulence intensities are set using passive grids. A spanwise-oriented phased-plasma-array actuator, fabricated on a printed circuit board, is surface-flush-mounted upstream of the separation point and can provide forcing in a wide frequency range. Static surface pressure measurements and hot-wire anemometry of the base and controlled flows are performed and indicate that the glow-discharge plasma actuator is an effective device for separation control.

Hultgren, Lennart S.↗

New results on the generation of broadband electrostatic waves in the magnetotail

The theory of the generation of broadband electrostatic noise (BEN) in the magnetotail is extended through numerical solution of the dispersion relation under conditions that exist in the plasma sheet boundary layer. It is found that the low-frequency portion of the spectrum has a broad angular spectrum but a fairly sharp peak near 75 deg with respect to the magnetic field, while the high-frequency portion has a narrower angular spectrum that is strongly concentrated along the magnetic field line. These results are in excellent agreement with observations of the broadband wave spectrum and a recent measurement of the propagation direction. The effect of a second cold component of electrons is analyzed, and it is found that it can increase the upper cutoff frequency of BEN to the observed value at about the plasma frequency.

Grabbe, C. L.↗

Plasma Distribution in Mercury's Magnetosphere Derived from MESSENGER Magnetometer and Fast Imaging Plasma Spectrometer Observations

We assess the statistical spatial distribution of plasma in Mercury's magnetosphere from observations of magnetic pressure deficits and plasma characteristics by the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) spacecraft. The statistical distributions of proton flux and pressure were derived from 10months of Fast Imaging Plasma Spectrometer (FIPS) observations obtained during the orbital phase of the MESSENGER mission. The Magnetometer-derived pressure distributions compare favorably with those deduced from the FIPS observations at locations where depressions in the magnetic field associated with the presence of enhanced plasma pressures are discernible in the Magnetometer data. The magnitudes of the magnetic pressure deficit and the plasma pressure agree on average, although the two measures of plasma pressure may deviate for individual events by as much as a factor of approximately 3. The FIPS distributions provide better statistics in regions where the plasma is more tenuous and reveal an enhanced plasma population near the magnetopause flanks resulting from direct entry of magnetosheath plasma into the low-latitude boundary layer of the magnetosphere. The plasma observations also exhibit a pronounced north-south asymmetry on the nightside, with markedly lower fluxes at low altitudes in the northern hemisphere than at higher altitudes in the south on the same field line. This asymmetry is consistent with particle loss to the southern hemisphere surface during bounce motion in Mercury's offset dipole magnetic field.

magnetic↗

Numerical study of the spectrum of broadband electrostatic noise in the magnetotail

A numerical study of the spectrum of broadband electrostatic noise (BEN) generated by ion beams in the plasma sheet boundary layer (PSBL) is presented, in which two cases are analyzed. The first case is concerned with a single hot-electron species. In the second case, a second population of cold electrons (arising from diffusion from the lobe into the PSBL) is introduced. The presence of the second electron component in the dispersion relation for generating BEN was found to significantly increase the upper frequency range of the unstable spectrum, enhancing the associated growth rates. It is shown that ion beam instabilities can explain most major features of the observed BEN spectrum. The results explain the gradual rise in the upper frequency range of BEN as a spacecraft approaches the plasma sheet from the lobe, and the sudden jump in that frequency up to near the plasma frequency upon crossing the PSBL.

Grabbe, Crockett L.↗

Magnetosonic waves adjacent to the plasma sheet in the distant magnetotail - ISEE-3

The presence of large-amplitude magnetosonic waves in the distant plasma sheet boundary layers is demonstrated, and their properties are discussed. The waves for almost all the events examined are right-hand circularly polarized, with the degree of polarization varying from 1.04 to 1.87, i.e., from circular to slightly elliptical. The waves are all propagating nearly along the magnetic field. Their periods vary from 3.7 seconds to as long as 35 seconds, with a median value of about 10 seconds, and are slightly larger than the proton gyroperiod in all but two cases. Most waves have a relatively large compressional component varying from 30 to 90 percent of the wave amplitude. Several possible generation mechanisms are discussed, along with the role that the waves may play in the heating and expansion of the plasma sheet.

Tsurutani, B. T.↗

Monitoring Delamination of Plasma-Sprayed Thermal Barrier Coatings by Reflectance-Enhanced Luminescence

Highly scattering plasma-sprayed thermal barrier coatings (TBCs) present a challenge for optical diagnostic methods to monitor TBC delamination because scattering attenuates light transmitted through the TBC and usually degrades contrast between attached and delaminated regions of the TBC. This paper presents a new approach where reflectance-enhanced luminescence from a luminescent sublayer incorporated along the bottom of the TBC is used to identify regions of TBC delamination. Because of the higher survival rate of luminescence reflecting off the back surface of a delaminated TBC, the strong scattering exhibited by plasma-sprayed TBCs actually accentuates contrast between attached and delaminated regions by making it more likely that multiple reflections of luminescence off the back surface occur before exiting the top surface of the TBC. A freestanding coating containing sections designed to model an attached or delaminated TBC was prepared by depositing a luminescent Eu-doped or Er-doped yttria-stabilized zirconia (YSZ) luminescent layer below a plasma-sprayed undoped YSZ layer and utilizing a NiCr backing layer to represent an attached substrate. For specimens with a Eu-doped YSZ luminescent sublayer, luminescence intensity maps showed excellent contrast between unbacked and NiCr-backed sections even at a plasma-sprayed overlayer thickness of 300 m. Discernable contrast between unbacked and NiCr-backed sections was not observed for specimens with a Er-doped YSZ luminescent sublayer because luminescence from Er impurities in the undoped YSZ layer overwhelmed luminescence originating form the Er-doped YSZ sublayer.

Eldridge, Jeffrey I.↗

Plasma sprayed ceramic thermal barrier coating for NiAl-based intermetallic alloys

A thermal barrier coating system consists of two layers of a zirconia-yttria ceramic. The first layer is applied by low pressure plasma spraying. The second layer is applied by conventional atmospheric pressure plasma spraying. This facilitates the attachment of a durable thermally insulating ceramic coating directly to the surface of a highly oxidation resistant NiAl-based intermetallic alloy after the alloy has been preoxidized to promote the formation of a desirable Al2O3 scale.

Miller, Robert A.↗

Analytical investigation of thermal barrier coatings for advanced power generation combustion turbines

An analytical evaluation was conducted to determine quantitatively the improvement potential in cycle efficiency and cost of electricity made possible by the introduction of thermal barrier coatings to power generation combustion turbine systems. The thermal barrier system, a metallic bond coat and yttria stabilized zirconia outer layer applied by plasma spray techniques, acts as a heat insulator to provide substantial metal temperature reductions below that of the exposed thermal barrier surface. The study results show the thermal barrier to be a potentially attractive means for improving performance and reducing cost of electricity for the simple, recuperated, and combined cycles evaluated.

Amos, D. J.↗

Development of a plasma sprayed ceramic gas path seal for high pressure turbine applications

Development of the plasma sprayed graded, layered ZrO2/CoCrAlY seal system for gas turbine engine blade tip seal application up to 1589 K (2400 F) surface temperature was continued. Methods of improvement of the cyclic thermal shock resistance of the sprayed zirconia seal system were investigated. The most promising method, reduction of the ceramic thickness and metallic substrate stiffness were selected based upon potential and feasibility. Specimens were fabricated and experimentally evaluated to: (1) substantiate the capacity of the geometry changes to reduce operating stresses in the sprayed structure; and (2) define the abradability, erosion, thermal shock and physical property characteristic for the sprayed ceramic seal system. Thermal stress analysis was performed and correlated with thermal shock test results.

Shiembob, L. T.↗

Development of improved high pressure turbine outer gas path seal components

A plasma sprayed graded layered ceramic/metallic (ZrO2/CoCrAlY) seal was evaluated for JT9D turbine application by rig and engine tests. Four cyclic thermal shock rig tests were conducted during the program. Three completed 1000 simulated engine thermal cycle tests and the fourth completed 500 cycles without severe cracking or spalling. Three ceramic seals were installed in a JT9D experimental engine to evaluate the effect of the engine thermal environment on the seals. All three seals completed the test successfully without severe cracking or spalling. The three seals did have slight laminar cracks at the 85/15-40/60 ZrO2/CoCrAlY interface. The second engine test evaluated the rub capabilities of the seal. Six ceramic seals were installed in the engine with fourteen abrasive tip blades. Three of the six seals rubbed to a depth of 24 mils. Eight of the fourteen abrasive tip blades showed evidence of wear. Three of the eight blades wore a maximum of five mils. Engine rub test results demonstrated the potential of reducing turbine clearances and thereby improving engine performance by use of sprayed ceramic seals.

Shiembob, L. T.↗

The dynamic behavior of the Venus ionosphere in response to solar wind interactions

The dynamics of the Venus ionosphere relates to the variations in the solar wind and the ionosheath magnetic fields as demonstrated by the electron density and temperature measurements of the Pioneer Venus orbiter electron probe. The mean ionopause height increases from 330 km at the subsolar point to 700 km at the dusk terminator, and to 1000 km at the dawn terminator; the dayside ionopause expands and contracts with solar wind pressure variations. Extreme spatial irregularities in the shape of holes, horizontally stratified layers, and detached plasma clouds are observed in the nightside ionosphere. The ion pickup on the dayside is described in terms of solar wind discontinuities inducing a wavelike pattern at the ionopause which is penetrated by the ionosheath plasma and magnetic fields which remove the plasma in the form of detached plasma clouds.

Brace, L. H.↗

Thermal barrier coating system having improved adhesion

The adherence between a ceramic thermal barrier coating and a metal bond coating is improved by ion sputtering a ceramic film on the bond cost. A ceramic thermal barrier coating is then plasma-sprayed onto this primer film. This improves the integrity and strength of the interface between the plasma-sprayed ceramic layer and metallic bond coat which insures stronger adherence between the metal and the ceramic.

Bill, R. C.↗

Generation of broadband electrostatic noise by ion beam instabilities in the magnetotail

Particle data from ISEE 1 sampled in the earth's magnetotail show the presence of energetic ion beams in the boundary layer of the plasma sheet. A theory of instabilities driven by the beams is developed and compared with wave data sampled simultaneously to the particle data. It is concluded that the ion beams generate broadband electrostatic bursts of noise. The electrostatic noise correlates well with the occurrence of the beams, and the spectrum is consistent with that predicted from a negative energy beam instability under magnetotail conditions. The theory predicts that a spectrum of growing waves can be driven for frequencies from 0.001 omega(pe) up to omega(pe), the electron plasma frequency, with a spectral peak typically near 0.01 omega(pe) or lower, in agreement with the wave data. Furthermore, as one moves away from the source region perpendicular to the magnetic field, the high frequency components of the observed wave spectra are predicted to disappear gradually, leaving the low frequency part of the spectrum, also as is observed. Evidence is given for significant pitch angle scattering of the beams by the broadband electrostatic noise, leading to more isotropic ion distributions.

Grabbe, C. L.↗

Origin of the plasma in a cross-polar cap auroral feature (theta aurora)

Ion composition data obtained from a particularly well observed cross-polar cap auroral feature (theta aurora) are presented. Two components of the hot plasma are identified, one from the ionosphere below and the second from the distant plasma sheet. These observations provide strong support for the conclusion that the cross-polar cap auroral feature occurs on field lines closing through the distant plasma sheet or plasma sheet boundary layer. Taken together with the previously published observations, these new results establish substantial constraints on models for the overall polar cap topology. However, they do not unambiguously favor either of the two principal topologies discussed in the literature.

Peterson, W. K.↗

The temporal evolution of a small auroral substorm as viewed from high altitudes with Dynamics Explorer 1

A small auroral substorm is investigated with auroral imaging photometers carried on the spacecraft Dynamics Explorer 1. Initial brightening along the auroral oval and the subsequent westward and poleward motions of intense, localized emission regions are associated with auroral surges. Following substorm onset, another region of less intense emissions is observed to develop at lower latitudes and adjacent to the bright region near local midnight. This second region expands towards the east. The bright zone of auroral emissions associated with the surges is interpreted as the signature of electron acceleration along magnetic field lines threading the boundary layer of the plasma sheet in the magnetotail. The more diffuse, less intense region is identified with eastward-drifting electrons injected into the plasma sheet and ring current following substorm onset. No rapid poleward motion of the discrete aurora is detected during substorm recovery.

Craven, J. D.↗

The polar ionosphere as a source of the storm time ring current

The transport of ions from the polar ionosphere to the inner magnetosphere during storm time conditions has been computed using a Monte Carlo diffusion code. The effect of the electrostatic turbulence assumed to be present during the substorm expansion phase was simulated by a process that accelerated the ions stochastically perpendicular to the magnetic field with a diffusion coefficient proportional to the rate of energization of the ions by the induced electric field. This diffusion process was continued as the ions were convected from the plasma sheet boundary layer to the double-spiral injection boundary. Inward of the injection boundary the ions were convected adiabatically. By using as input an O(+) flux of 2.8 x 10 to the 8th per sq cm per s (w greater than 10 eV) and an H(+) flux of 5.5 x 10 to the 8th per sq cm per s (w greater than .63 eV) the computed distribution functions of the ions in the ring current were found to be in good agreement, over a wide range in L (4-8), with measurements made with the ISEE 1 satellite during a storm. This O(+) flux and a large part of the H(+) flux appear to be consistent with the DE-1 and DE-2 satellite measurements of the polar ionospheric outflow during disturbed times.

Cladis, J. B.↗

The temporal evolution of a small auroral substorm as viewed from high altitudes with Dynamics Explorer 1

A small auroral substorm is investigated with auroral imaging photometers carried on the spacecraft Dynamics Explorer 1. Initial brightening along the auroral oval and the subsequent westward and poleward motions of intense, localized emission regions are associated with auroral surges. Following substorm onset, another region of less intense emissions is observed to develop at lower latitudes and adjacent to the bright region near local midnight. This second region expands toward the east. The bright zone of auroral emissions associated with the surges is interpreted as the signature of electron acceleration along magnetic field lines threading the boundary layer of the plasma sheet in the magnetotail. The more diffuse, less intense region is identified with eastward-drifting electrons injected into the plasma sheet and ring current following substorm onset. No rapid poleward motion of the discrete aurora is detected during substorm recovery.

Craven, J. D.↗

Transport of ions in presence of induced electric field and electrostatic turbulence - Source of ions injected into ring current

The transport of ions from the polar ionosphere to the inner magnetosphere during stormtime conditions has been computed using a Monte Carlo diffusion code. The effect of the electrostatic turbulence assumed to be present during the substorm expansion phase was simulated by a process that accelerated the ions stochastically perpendicular to the magnetic field with a diffusion coefficient proportional to the energization rate of the ions by the induced electric field. This diffusion process was continued as the ions were convected from the plasma sheet boundary layer to the double-spiral injection boundary. Inward of the injection boundary, the ions were convected adiabatically. By using as input an O(+) flux of 2.8 x 10 to the 8th per sq cm per s (w greater than 10 eV) and an H(+) flux of 5.5 x 10 to the 8th per sq cm per s (w greater than 0.63 eV), the computed distribution functions of the ions in the ring current were found to be in good agreement, over a wide range in L (4 to 8), with measurements made with the ISEE-1 satellite during a storm. This O(+) flux and a large part of the H(+) flux are consistent with the DE satellite measurements of the polar ionospheric outflow during disturbed times.

Cladis, J. B.↗