Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLASMA TEMPERATURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Latitudinal variability of large-scale coronal temperature and its association with the density and the global magnetic field

In this paper we utilize the latitiude distribution of the coronal temperature during the period 1984-1992 that was derived in a paper by Guhathakurta et al, 1993, utilizing ground-based intensity observations of the green (5303 A Fe XIV) and red (6374 A Fe X) coronal forbidden lines from the National Solar Observatory at Sacramento Peak, and establish it association with the global magnetic field and the density distributions in the corona. A determination of plasma temperature, T, was estimated from the intensity ratio Fe X/Fe XIV (where T is inversely proportional to the ratio), since both emission lines come from ionized states of Fe, and the ratio is only weakly dependent on density. We observe that there is a large-scale organization of the inferred coronal temperature distribution that is associated with the large-scale, weak magnetic field structures and bright coronal features; this organization tends to persist through most of the magnetic activity cycle. These high-temperature structures exhibit time-space characteristics which are similar to those of the polar crown filaments. This distribution differs in spatial and temporal characterization from the traditional picture of sunspot and active region evolution over the range of the sunspot cycle, which are manifestations of the small-scale, strong magnetic field regions.

Guhathakurta, M.↗
DOE OSTI2024

Effect of detachment on Magnum-PSI ELM-like pulses: direct observations and qualitative results

Abstract Conditions similar to those at the end of the divertor leg in a tokamak were replicated in the linear plasma machine Magnum-PSI. The neutral pressure in the target chamber is then increased to cause the target to transition from an attached to a detached state. Superimposed to this steady state regime, edge localised mode (ELM)-like pulses are reproduced, resulting in a sudden increase in plasma temperature and density, such that the heat flux increases transiently by half an order of magnitude. Visible light emission, target thermography, and Thomson scattering are used to demonstrate that the higher the neutral pressure the more energy is removed from the ELM-like pulse in the volume. If the neutral pressure is sufficiently high, the ELM-like pulse can be prevented from affecting the target and the plasma energy is fully dissipated in the volume instead (ID 4 in table 1). The visible light images allow the division of the ELM-plasma interaction process of ELM energy dissipation into 3 ‘stages’ ranging from no dissipation to full dissipation (the target plasma is detached). In the second publication related to this study, spectroscopic data is analysed with a Bayesian approach, to acquire insights into the significance of molecular processes in dissipating the plasma energy and particles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1978

MHD conversion of solar energy

Low temperature plasmas wherein an alkali metal vapor is a component are uniquely suited to simultaneously absorb solar radiation by coupling to the resonance lines and produce electrical power by the MHD interaction. This work is an examination of the possibility of developing space power systems which take advantage of concentrated solar power to produce electricity. It is shown that efficient cycles in which expansion work takes place at nearly constant top cycle temperature can be devised. The power density of the solar MHD generator is lower than that of conventional MHD generators because of the relatively high seed concentration required for radiation absorption and the lower flow velocity permitted to avoid total pressure losses due to heating.

Lau, C. V.↗
NASA NTRS1995

Exploring the temperature structure of coronal holes with a novel combination of visible Fe lines

The difficulty in establishing the temperature structure and temperature gradient within coronal holes from limb observations is due to the frequent veiling of coronal holes by hotter and denser quiet regions often surrounding them and shaping their boundaries. Nevertheless probing the coronal hole medium itself can be made with a judicious choice of spectral lines. We show how a set of visible forbidden Fe lines, namely Fe IX 3801, Fe X 6374 and Fe Xl 7892 A which are sensitive to plasma temperatures less than or equal to 10(exp 6) K can achieve this purpose. We propose to use these lines in a coordinated manner with coronagraph observations. In addition observations made with the Fe XIV 5303 A line should yield information about any hot material intercepting the line of sight. The proposed combination of these Fe lines offers a very powerful diagnostic tool for coronal hole temperatures and structures.

Habbal, Shadia Rifai↗
NASA NTRS1992

Nonadiabatic heating of the central plasma sheet at substorm onset

Heating events in the plasma sheet boundary layer and central plasma sheet are found to occur at the onset of expansive phase activity. The main effect is a dramatic increase in plasma temperature, coincident with a partial dipolarization of the magnetic field. Fluxes of energetic particles increase without dispersion during these events which occur at all radial distances up to 23 RE, the apogee of the ISEE spacecraft. A major difference between these heating events and those observed at geosynchronous distances lies in the heating mechanism which is nonadiabatic beyond 10 RE but may be adiabatic closer to earth. The energy required to account for the increase in plasma thermal energy is comparable with that required for Joule heating of the ionosphere. The plasma sheet must be considered as a major sink in the energy balance of a substorm. Lobe magnetic pressures during these events are estimated. Change in lobe pressure are generally not correlated with onsets or intensifications of expansive phase activity.

Huang, C. Y.↗
DOE OSTI2024

Coupled Experimental/Computational Investigation of the Dynamics of Interacting Magnetized Plasmas

The interaction, or interpenetration, of magnetized plasmas of different density and/or pressure occurs in a wide variety of natural and man-made systems. Such systems include extragalactic jets propagating into the intergalactic medium, solar coronal mass ejections into background solar wind, compact toroid (CT) fueling of magnetic fusion plasmas, and jets of capsule shell impurities into DT fusion fuel, which can lead to enhanced impurity mix in inertial fusion implosions. These plasmas may take the form of jets, with open, helical magnetic structure, or plasma “bubbles” with closed magnetic fields (B-fields), such as spheromaks or CT’s. Such structures, both open and closed B-field cases, can transport heat, particles and magnetic flux or magnetic helicity into background plasma regions. For example, the origin of extragalactic magnetic fields may be due, at least in part, to transport by astrophysical jets. The goal of this proposed work was to elucidate the detailed plasma and magnetic field dynamics of high-density plasma jets (open B-field) and bubbles (closed B-field) propagating into lower density background magnetized plasma through controlled laboratory experiments and closely coupled nonlinear MHD modeling. These experiments were conducted in the HelCat (Helicon-Cathode) linear plasma device at the University of New Mexico (UNM). Plasma jets and bubbles were launched via an existing compact coaxial plasma gun, mounted on the HelCat device. This gun produced plasmas tens of cm in scale and lasting tens of microseconds, thereby allowing detailed multipoint, space- and time-resolved measurements to be made routinely. The experiments were directly modeled using the extended magnetohydrodynamic (XMHD) PERSEUS code, developed at Cornell University [23,24]. Both experimental and numerical modeling work are ongoing. The main results to date are reported here. Additional supplemental funding for one year (8/1/2019 – 7/31/2020) supported numerical investigation of photoionization processes important in many low temperature plasmas, including the HelCat device. Initial results of this modeling work is also reported.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Modeling resistive-inductive evolution of currents in Wendelstein 7-X

This research investigates the temporal evolution of the toroidal plasma current in the Wendelstein 7-X (W7-X) stellarator under different heating, fueling, and current drive scenarios. The THRIFT code has been modernized and its predictions of the evolution of the toroidal current have been compared against experimentally measured currents in W7-X. Good agreement is found with respect to the characteristic timescale between experimentally measured and simulated toroidal currents. The total bootstrap current is under-predicted owing to the applicability of the BOOTSJ model for the plasma collisionalities in question. Edge plasma resistivity is found to play an important role in the asymptotic behavior of the evolution of the current, indicating a possible limitation of the minimum plasma temperature when applying this model. Simulations of ECCD and heating power steps show THRIFT is capable of capturing the dynamical evolution of the current in response to changes in current sources. Future uses of THRIFT include validating and benchmarking other non-inductive current models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1983

Escape and ionization of atomic oxygen from Io

Model calculations of the neutral O cloud of Io, based on atom-electron-impact excitation and ionization processes in the plasma torus, are presented. The model is quantitatively anchored to the 6300-A O I emission intensity observations of Brown (1981), and uses a plasma temperature and density structure based on Voyager 1 and 2 and EUV data. Parameters predicted by the model include satellite emission flux = 1.5 x 10 to the 9th/sq cm sec, ion-loading rate = 6.2 x 10 to the 26th ions/sec, O mass-loading rate = 16.6 kg/sec, and O ion-energy input rate = 2.7 x 10 to the 10th W. The spatial morphologies of the parameters are shown. Rough estimates obtained by accounting for a neutral S cloud and plasma-torus charge-exchange reactions include O source flux = 1.2 x 10 to the 10th/sq cm sec, ion-loading rate = 4.0 x 10 to the 27th ions/sec, ion-diffusive-loss time = 200 days, plasma mass-loading rate = 150 kg/sec, satellite mass-loss rate = 270 kg/sec, and maximum ion-energy input = 4 x 10 to the 11th W.

Smyth, W. H.↗
NASA NTRS1993

Large-scale coronal temperature and density distributions, 1984-1992

We characterize the temperature and the density structure of the corona utilizing spectrophotometric observations at different heights but at the same latitude during the descending phase of cycle 21 through the ascending phase of cycle 22. The data include ground-based intensity observations of the green (Fe XIV 5303) and red (Fe X 6374) coronal forbidden lines, photospheric magnetographs from the National Solar Observatory, Kitt Peak, and synoptic maps of white-light K-coronal polarized brightness from the High Altitude Observatory. A determination of plasma temperature, T, can be estimated from the intensity ratio Fe X/Fe XIV (where T is inversely proportional to the ratio), since both emission lines come from ionized states of Fe, and the ratio is only weakly dependent on density. Distributions of the electron temperature from the line ratio and the polarized brightness which yields electron density of the corona during the descending and the ascending phases of solar cycles 21 and 22 are presented. These data refer to structures of the corona which are relatively large scale, having a temporal coherence of at least two or more synoptic rotation periods, such as the streamer belts, the individual helmet streamers, and the larger coronal holes.

Guhathakurta, M.↗
NASA NTRS1994

The solar cycle variation of coronal temperature and density during cycle 21-22

In this paper we characterize the temperature and the density structure of the corona utilizing co-spatial spectrophotometric observations during the descending phase of cycle 21 through the ascending phase of cycle 22. The data include ground-based intensity observations of the green (5303A Fe XIV) and red (6374A Fe X) coronal forbidden lines from Sacramento Peak and synoptic maps of white-light K-coronal polarized brightness, pB from the High Altitude Observatory, and photospheric magnetographs from the National Solar Observatory, Sacramento Peak. A determination of plasma temperature T can be derived unambiguously from the intensity ratio Fe X/Fe XIV, since both emission lines come from ionized states of Fe, and the ratios are only weakly dependent on density. The latitudinal variation of the temperature and the density within the descending and the ascending phases of solar cycle 21 and 22 are presented. There is a large-scale organization of the inferred coronal temperature distribution; these structures tend to persist through most of the magnetic activity cycle. This distribution differs in spatial and temporal characterization from the traditional picture of sunspot and active region evolution over the range of sunspot cycle.

Guhathakurta, M.↗
NASA NTRS2004

XMM-Newton Observations of the 2003 X-Ray Minimum of Eta Carinae

The XMM-Newton X-ray observatory took part in the multi-wavelength observing campaign of the massive, evolved star Eta Carinae in 2003 during its recent X-ray minimum in June 2003. This paper reports on the first results of these observations, which were performed (1) before the minimum (five times in January, 2003), (2) near the X-ray maximum just before the minimum (two times in June) and (3) during the minimum (four times in July-August). Hard X-ray emission from the point source of Eta Carinae was detected even during the minimum. The observed flux above 3 keV was approx. 3x10(exp -12) ergs cm(exp -2)/s, which is about one percent of the flux before the minimum. Light curves from the individual observations show no time variability on the scale of a few kilo-seconds. Changes in the spectral shape occurred, but these changes were smaller than expected if the minimum is produced solely by an increase of hydrogen column density. Fits of the hard X-Ray source by an absorbed 1T model show a constant plasma temperature at around 5 keV and an increase of column density from 5x10(exp 22) cm(exp -2) to 2x10(exp 23) cm(exp -2). The spectra below 6 keV significantly deviate from the models that fit the higher energy emission. The X-ray minimum seems to be dominated by an apparent decrease of the emission measure, suggesting that the brightest part of the X-ray emitting region is completely obscured during the minimum in the form of an eclipse. Partial covering plasma emission models might be considered for the spectral variation. The spectra also showed strong iron K line emission from both hot and cold gases, and weak line emission from Ni, Ca, Ar, S and Si.

Hamaguchi, K.↗
NASA NTRS2002

Ion Storage Ring Measurements of Low Temperature Dielectronic Recombination Rate Coefficients for Modeling X-Ray Photoionized Cosmic Plasmas

Low temperature dielectronic recombination (DR) is the dominant recombination mechanism for most ions in X-ray photoionized cosmic plasmas. Reliably modeling and interpreting spectra from these plasmas requires accurate low temperature DR rate Coefficients. Of particular importance are the DR rate coefficients for the iron L-shell ions (Fe XVII-Fe XXIV). These ions are predicted to play an important role in determining the thermal structure and line emission of X-ray photoionized plasmas, which form in the media surrounding accretion powered sources such as X-ray binaries (XRBs), active galactic nuclei (AGN), and cataclysmic variables (Savin et al., 2000). The need for reliable DR data of iron L-shell ions has become particularly urgent after the launches of Chandra and XMM-Newton. These satellites are now providing high-resolution X-ray spectra from a wide range of X-ray photoionized sources. Interpreting the spectra from these sources requires reliable DR rate coefficients. However, at the temperatures relevant, for X-ray photoionized plasmas, existing theoretical DR rate coefficients can differ from one another by factors of two to orders of magnitudes.

Savin, D. W.↗
DOE OSTI2025

Comprehensive Diagnostics for Bond-Selective Nanocarbon Growth in Plasmas

This award was continuation funding for our previously supported efforts into carbon nanoparticle synthesis with tunable bond hybridization, including for luminescent carbon nanoparticles, amorphous carbon nanoparticles, and eventually nanodiamond. Beginning in early 2021 we supported preliminary experiments with in-house funds. In February 2021 our user proposal to the PCRF to investigate this topic was accepted and our experiments at PCRF took place in July 2022. DOE awarded this proposal to support data analysis based on those experiments, and supported the continued efforts towards finalizing that work. With those results and further efforts, we will be able to finalize our early research into nucleation and growth of carbon nanoparticles for a long-term objective of selective bonding in carbon and other nanomaterials grown in low-temperature plasmas. We made several important discoveries.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

High-Fidelity Arc-Discharge Model for Hydrogen-Plasma-Smelting-Reduction of Iron Ore

Electrification and use of renewable hydrogen is currently a necessity for decarbonizing the iron-and-steel industry. In this regard, hydrogen plasma smelting reduction (HPSR) is a novel pathway that is being explored for reduction of iron ore. HPSR provides several decarbonization merits compared to conventional blast furnaces. Firstly, the use of renewable hydrogen drastically reduces the CO2 emissions compared to the use of coke. Secondly, renewable electricity in the form of a thermal plasma for making reactive hydrogen species (radicals, ions) are more efficient at reducing iron ore compared to neutral H2. Thirdly, a molten product compatible with downstream processes is obtained from the intense heat transfer from the plasma. However, the scale-up of this technology requires fundamental exploration of hydrogen plasma dynamics and its interaction with complex solid material that include phase changing iron-ore and slag. In this work, we present a first principles continuum scale model for thermal plasmas in Ar/H2 gas mixtures typically used for HPSR. The thermal plasma governing equations for mass, momentum and energy with Lorentz force and Joule heating source terms are solved along with electromagnetic equations for electrostatic and magnetic vector potential. Our solver will be based on Pele, a suite of reacting flow solvers designed for advanced scientific computing architectures (Henry De Frahan et al., Proceedings of SIAM Parallel Processing, 13-25, 2024), and will utilize adaptive mesh generation for enhanced resolutions at locations of intense physicochemical interactions. This study will present the impact of Ar to H2 ratios on excited/dissociated hydrogen species concentrations, plasma temperature and conductivity along with the impact of outgassed species (water, metal vapor, O, OH radicals) from ore surface on gas phase chemistry. Furthermore, the heat and species flux to the surface will be quantified as a function of applied voltages in a transferred arc configuration.

hydrogen plasma↗
NASA NTRS1989

Antiproton powered propulsion with magnetically confined plasma engines

Matter-antimatter annihilation releases more energy per unit mass than any other method of energy production, making it an attractive energy source for spacecraft propulsion. In the magnetically confined plasma engine, antiproton beams are injected axially into a pulsed magnetic mirror system, where they annihilate with an initially neutral hydrogen gas. The resulting charged annihilation products transfer energy to the hydrogen propellant, which is then exhausted through one end of the pulsed mirror system to provide thrust. The calculated energy transfer efficiencies for a low number density (10(14)/cu cm) hydrogen propellant are insufficient to warrant operating the engine in this mode. Efficiencies are improved using moderate propellant number densities (10(16)/cu cm), but the energy transferred to the plasma in a realistic magnetic mirror system is generally limited to less than 2 percent of the initial proton-antiproton annihilation energy. The energy transfer efficiencies are highest for high number density (10(18)/cu cm) propellants, but plasma temperatures are reduced by excessive radiation losses. Low to moderate thrust over a wide range of specific impulse can be generated with moderate propellant number densities, while higher thrust but lower specific impulse may be generated using high propellant number densities. Significant mass will be required to shield the superconducting magnet coils from the high energy gamma radiation emitted by neutral pion decay. The mass of such a radiation shield may dominate the total engine mass, and could severely diminish the performance of antiproton powered engines which utilize magnetic confinement. The problem is compounded in the antiproton powered plasma engine, where lower energy plasma bremsstrahlung radiation may cause shield surface ablation and degradation.

Lapointe, Michael R.↗
NASA NTRS2023

Delayed Development of Cool Plasmas in X-Ray Flares from the Young Sun-like Star κ1 Ceti

The Neutron star Interior Composition Explorer (NICER) X-ray observatory observed two powerful X-ray flares equivalent to superflares from the nearby young solar-like star κ 1 Ceti in 2019. NICER follows each flare from the onset through the early decay, collecting over 30 counts s −1 near the peak, enabling a detailed spectral variation study of the flare rise. The flare in September varies quickly in ∼800 s, while the flare in December has a few times longer timescale. In both flares, the hard-band (2–4 keV) light curves show typical stellar X-ray flare variations with a rapid rise and slow decay, while the soft X-ray light curves, especially of the September flare, have prolonged flat peaks. The time-resolved spectra require two temperature plasma components at kT ∼0.3–1 and ∼2–4 keV. Both components vary similarly, but the cool component lags by ∼200 s with a four to six times smaller emission measure (EM) compared to the hot component. A comparison with hydrodynamic flare loop simulations indicates that the cool component originates from X-ray plasma near the magnetic loop footpoints that mainly cools via thermal conduction. The time lag represents the travel time of the evaporated gas through the entire flare loop. The cool component has a several times smaller EM than its simulated counterpart, suggesting a suppression of conductive cooling, possibly by the expansion of the loop cross-sectional area or turbulent fluctuations. The cool component's time lag and EM ratio provide important constraints on the flare loop geometry.

main sequence stars↗
DOE OSTI2024

Study of x-ray fluorescence spectroscopy from high-energy-density plasmas (Final Report)

The primary objective of this subcontract was to support the development of x-ray fluorescence spectroscopy (XFS) as a diagnostic tool for high-energy-density (HED) plasmas. Several experimental campaigns were completed to develop and benchmark XFS at various plasmas conditions of interest for inertial confinement fusion and HED science. The experimental measurements at the Omega laser facility used x-ray absorption spectroscopy (XAS) to determine the plasma temperature from the shape of the K-edge to benchmark XFS data. During the course of these experiments, it was found that XAS can also constrain ionization from bound-bound absorption features, and it became a primary diagnostic in this study. Several experimental campaigns were conducted at the Omega laser facility to refine XAS and XFS measurements of warm dense copper.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Plasma-assisted atomic layer etching of single-crystal diamond

Applications of near-surface nitrogen-vacancy (NV) centers in diamond are often limited by surface defects created during processing. Understanding and controlling plasma-induced surface damage is important for preserving the optical and spin properties of diamond NV centers. We report molecular dynamics simulations of a novel form of plasma-aided atomic layer etching of diamond. In this proposed scheme, the initial surface modification step consists of Ar + ion bombardment. This creates an amorphous layer at the surface, the thickness of which is controlled by the ion energy. Amorphization is known to help smooth the surface, at least locally, and would also serve to sputter clean an initially contaminated surface. A second step impacts the amorphous carbon layer with O + between about 1 and 5 eV. Simulations show that this energy range will remove the amorphous carbon but will not etch the underlying diamond. Though this energy range is not trivial to achieve in a conventional low-temperature plasma, potential methods for creating these low-energy O + ions are discussed. In addition to a-C etching, the O + impacts are predicted to remove any isolated (100) diamond terraces by selectively attacking the edges of the terraces. The proposed atomic layer etching (ALE) approach reverses the conventional ALE sequence in which the surface modification step is usually chemical modification (oxidation in this case), followed by a removal step using Ar + impacts. This plasma ALE procedure is predicted to create a diamond surface that is atomically flat and defect free.

Draney, J. S. [Princeton University, NJ (United St↗