Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATES, FLAT - SHEAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1958

On flow of electrically conducting fluids over a flat plate in the presence of a transverse magnetic field

The use of a magnetic field to control the motion of electrically conducting fluids is studied. The incompressible boundary-layer solutions are found for flow over a flat plate when the magnetic field is fixed relative to the plate or to the fluid. The equations are integrated numerically for the effect of the transverse magnetic field on the velocity and temperature profiles, and hence, the skin friction and rate of heat transfer. It is concluded that the skin friction and the heat-transfer rate are reduced when the transverse magnetic field is fixed relative to the plate and increased when fixed relative to the fluid. The total drag is increased in all of the areas.

Rossow, Vernon J↗
NASA NTRS1975

Development of flat-plate solar collectors for the heating and cooling of buildings

The relevant design parameters in the fabrication of a solar collector for heating liquids were examined. The objective was to design, fabricate, and test a low-cost, flat-plate solar collector with high collection efficiency, high durability, and requiring little maintenance. Computer-aided math models of the heat transfer processes in the collector assisted in the design. The preferred physical design parameters were determined from a heat transfer standpoint and the absorber panel configuration, the surface treatment of the absorber panel, the type and thickness of insulation, and the number, spacing and material of the covers were defined. Variations of this configuration were identified, prototypes built, and performance tests performed using a solar simulator. Simulated operation of the baseline collector configuration was combined with insolation data for a number of locations and compared with a predicted load to determine the degree of solar utilization.

Ramsey, J. W.↗
NASA NTRS1986

Flat-plate solar array project. Volume 4: High-efficiency solar cells

The High Efficiency Solar Cell Task was assigned the objective of understanding and developing high efficiency solar cell devices that would meet the cost and performance goals of the Flat Plate Solar Array (FSA) Project. The need for research dealing with high efficiency devices was considered important because of the role efficiency plays in reducing price per watt of generated energy. The R&D efforts conducted during the 1982 to 1986 period are summarized to provide understanding and control of energy conversion losses associated with crystalline silicon solar cells. New levels of conversion efficiency were demonstrated. Major contributions were made both to the understanding and reduction of bulk and surface losses in solar cells. For example, oxides, nitrides, and polysilicon were all shown to be potentially useful surface passivants. Improvements in measurement techniques were made and Auger coefficients and spectral absorption data were obtained for unique types of silicon sheets. New modelling software was developed including a program to optimize a device design based on input characteristics of a cell.

Leipold, M.↗
NASA NTRS1994

Design of 3-D Nacelle near Flat-Plate Wing Using Multiblock Sensitivity Analysis (ADOS)

One of the major design tasks involved in reducing aircraft drag is the integration of the engine nacelles and airframe. With this impetus, nacelle shapes with and without the presence of a flat-plate wing nearby were optimized. This also served as a demonstration of the 3-D version of the recently developed aerodynamic design optimization methodology using sensitivity analysis, ADOS. The required flow analyses were obtained by solving the three-dimensional, compressible, thin-layer Navier-Stokes equations using an implicit, upwind-biased, finite volume scheme. The sensitivity analyses were performed using the preconditioned version of the SADD scheme (sensitivity analysis on domain decomposition). In addition to demonstrating the present method's capability for automatic optimization, the results offered some insight into two important issues related to optimizing the shapes of multicomponent configurations in close proximity. First, inclusion of the mutual interference between the components resulted in a different shape as opposed to shaping an isolated component. Secondly, exclusion of the viscous effects compromised not only the flow physics but also the optimized shapes even for isolated components.

Eleshaky, Mohamed E.↗
NASA NTRS1984

Design of high-Reynolds-number flat-plate experiments in the NTF

The design of an experiment to measure skin friction and turbulent boundary-layer characteristics at Reynolds numbers exceeding one billion is described. The experiment will be conducted in a zero-pressure-gradient flow on a flat plate in the National Transonic Facility. The development of computational codes to analyze the aerodynamic loads and the blockage is documented. Novel instrumentationn techniques and models, designed to operate in cryogenic environments, are presented. Special problems associated with aerodynamic loads, surface finish, and hot-wire anemometers are discussed.

Saric, W. S.↗
NASA NTRS1984

Flat plate heat transfer for laminar transition and turbulent boundary layers using a shock tube

Heat transfer results are presented for laminar, transition, and turbulent boundary layers for a Mach number of 0.12 with gas temperatures of 425 K and 1000 K over a flat plate at room temperature. The measurements were made in air for a Reynolds number range of 600 to 6 million. The heat transfer measurements were conducted in a 70-ft long, 4 in. diameter shock tube. Reflecting wedges were used to reflect the incident shock wave to produce a flow Mach number of 0.12 behind the reflected shock wave. Thin film platinum heat gages were mounted on the plate surface to measure the local heat flux. The laminar results for gas temperatures of 425 K to 1000 K agree well with theory. The turbulent results are also close to incompressible theory, with the 1000 K flow case being slightly higher. The transition results lie between the laminar and turbulent predictions.

Brostmeyer, J. D.↗
NASA NTRS1991

Visualization of leading edge vortices on a series of flat plate delta wings

A summary of flow visualization data obtained as part of NASA Grant NAG2-258 is presented. During the course of this study, many still and high speed motion pictures were taken of the leading edge vortices on a series of flat plate delta wings at varying angles of attack. The purpose is to present a systematic collection of photographs showing the state of vortices as a function of the angle of attack for the four models tested.

Payne, Francis M.↗
NASA NTRS1985

Experimental observation of transition behavior on a flat plate

In studying transition behavior a shock tube and tunnel were used to produce high temperatures, and thin-film platinum heat gauges were used to measure local heat flux as well as to detect the transition of the laminar boundary layer over a flat plate and a cone. Initial investigations were conducted in the hypersonic shock tunnel to obtain high-temperature information for the development of an ICBM nose cone. Shock Mach numbers as large as 50 with a temperature of 15,000 K after the incident wave were produced in the driven tube. Shock tubes are used to investigate the heat transfer over various surfaces to 2500 K for the development of future gas turbines.

Nagamatsu, H. T.↗
NASA NTRS1996

High Reynolds number analysis of flat plate and separated afterbody flow using non-linear turbulence models

The ability of the three-dimensional Navier-Stokes method, PAB3D, to simulate the effect of Reynolds number variation using non-linear explicit algebraic Reynolds stress turbulence modeling was assessed. Subsonic flat plate boundary-layer flow parameters such as normalized velocity distributions, local and average skin friction, and shape factor were compared with DNS calculations and classical theory at various local Reynolds numbers up to 180 million. Additionally, surface pressure coefficient distributions and integrated drag predictions on an axisymmetric nozzle afterbody were compared with experimental data from 10 to 130 million Reynolds number. The high Reynolds data was obtained from the NASA Langley 0.3m Transonic Cryogenic Tunnel. There was generally good agreement of surface static pressure coefficients between the CFD and measurement. The change in pressure coefficient distributions with varying Reynolds number was similar to the experimental data trends, though slightly over-predicting the effect. The computational sensitivity of viscous modeling and turbulence modeling are shown. Integrated afterbody pressure drag was typically slightly lower than the experimental data. The change in afterbody pressure drag with Reynolds number was small both experimentally and computationally, even though the shape of the distribution was somewhat modified with Reynolds number.

Carlson, John R.↗
NASA NTRS1988

Design of high-Reynolds-number flat-plate experiments in the NTF

The design of an experiment to measure skin friction and turbulent boundary layer characteristics at Reynolds numbers exceeding 1 x 10 to the 9th is described. The experiment will be conducted in a zero-pressure-gradient flow on a flat plate in the National Transonic Facility (NTF). The development of computational codes to analyze the aerodynamic loads and the blockage is documented. Novel instrumentation techniques and models, designed to operate in cryogenic environments, are presented. Special problems associated with aerodynamic loads, surface finish, and hot-wire anemometers are discussed.

Saric, William S.↗
NASA NTRS1975

Results of convective heating tests of a longitudinal gap on the Rockwell flat plate model (15-0, insert 7) in the NASA/Ames Research Center

Results are presented which were obtained from tests in a hypersonic wind tunnel to determine aerodynamic heating rates in a gap running parallel or slightly askew to the flow direction. The model used was a flat plate instrumented in thin-skin sections with chromelconstantan thermocouples. Heating rate profiles lengthwise along and down into the gap were obtained, and additional data were obtained from a total temperature probe and rake fabricated during the test to investigate an apparent aerodynamic cooling trend in the gap. Model variables were width, depth, length, and orientation of the gap relative to the flow direction. The tests were conducted at Mach 5.1 and Reynolds numbers per foot of 500,000, 1,000,000, and 2,000,000.

Quan, M.↗
NASA NTRS1982

Cost estimates for flat plate and concentrator collector arrays

The current module and installation costs for the U.S. National Photovoltaic Program's grid-connected systems are significantly higher than required for economic viability of this alternative. Attention is accordingly given to the prospects for installed module cost reductions in flat plate, linear focus Fresnel concentrator, and point focus Fresnel concentrator candidate systems. Cost projections indicate that all three systems would meet near-term and midterm goals, provided that module costs of $2.80/W(p) and $0.70/W(p), respectively, are met. The point focus Fresnel system emerges as the most viable for the near term.

Shimada, K.↗
NASA NTRS2006

Three-Dimensional Thermal Boundary Layer Corrections for Circular Heat Flux Gauges Mounted in a Flat Plate with a Surface Temperature Discontinuity

Three-dimensional Navier-Stokes computational fluid dynamics (CFD) analysis has been performed in an effort to determine thermal boundary layer correction factors for circular convective heat flux gauges (such as Schmidt-Boelter and plug type)mounted flush in a flat plate subjected to a stepwise surface temperature discontinuity. Turbulent flow solutions with temperature-dependent properties are obtained for a free stream Reynolds number of 1E6, and freestream Mach numbers of 2 and 4. The effect of gauge diameter and the plate surface temperature have been investigated. The 3-D CFD results for the heat flux correction factors are compared to quasi-21) results deduced from constant property integral solutions and also 2-D CFD analysis with both constant and variable properties. The role of three-dimensionality and of property variations on the heat flux correction factors has been demonstrated.

Kandula, M.↗
NASA NTRS1984

Flow past a Flat Plate with a Vortex/sink Combination

An attempt was made to model the so called leading edge vortex which forms over the leading edge of delta wings at high angles of attack. A simplified model was considered, namely that of a two-dimensional, inviscid, incompressible steady flow around a flat plate at an angle of attack with a stationary vortex detached on top, as well as a sink to simulate the strong spanwise flow. The results appear to agree qualitatively with experiments. A comparison was also made between the lift and the drag of this model and the corresponding results for two classical solutions: (1) that of totally attached flow over the plate with the Kutta condition satisfied at the trailing edge only: and (2) the Helmholtz solution of totally separated flow over the plate.

Mourtos, N. J.↗
NASA NTRS1961

Pressure Loads Produced on a Flat-Plate Wing By Rocket Jets Exhausting in a Spanwise Direction Below the Wing and Perpendicular to a Free-Stream Flow of Mach Number 2.0

An investigation at a Reynolds number per foot of 14.4 x 10(exp 6) was made to determine the pressure loads produced on a flat-plate wing by rocket jets exhausting in a spanwise direction beneath the wing and perpendicular to a free-stream flow of Mach number 2.0. The ranges of the variables involved were (1) nozzle types - one sonic (jet Mach number of 1.00), two supersonic (jet Mach numbers of 1.74 and 3.04),. and one two-dimensional supersonic (jet Mach number of 1.71); (2) vertical nozzle positions beneath the wing of 4, 8 and 12 nozzle-throat diameters; and (3) ratios of rocket-chamber total pressure to free- stream static pressure from 0 to 130. The incremental normal force due to jet interference on the wing varied from one to two times the rocket thrust and generally decreased as the pressure ratio increased. The chordwise coordinate of the incremental-normal-force center of pressure remained upstream of the nozzle center line for the nozzle positions and pressure ratios of the investigation. The chordwise coordinate approached zero as the jet vertical distance beneath the wing increased. In the spanwise direction there was little change due to varying rocket-jet position and pressure ratio. Some boundary-layer flow separation on the wing was observed for the rocket jets close to the wing and at the higher pressure ratios. The magnitude of the chordwise and spanwise pressure distributions due to jet interference was greatest for rocket jets close to the wing and decreased as the jet was displaced farther from the wing. The design procedure for the rockets used is given in the appendix.

Falanga, Ralph A.↗
NASA NTRS1986

Flat-plate solar array project. Volume 7: Module encapsulation

The objective of the Encapsulation Task was to develop, demonstrate, and qualify photovoltaic (PV) module encapsulation systems that would provide 20 year (later decreased to 30 year) life expectancies in terrestrial environments, and which would be compatible with the cost and performance goals of the Flat-Plate Solar Array (FSA) Project. The scope of the Encapsulation Task included the identification, development, and evaluation of material systems and configurations required to support and protect the optically and electrically active solar cell circuit components in the PV module operating environment. Encapsulation material technologies summarized include the development of low cost ultraviolet protection techniques, stable low cost pottants, soiling resistant coatings, electrical isolation criteria, processes for optimum interface bonding, and analytical and experimental tools for evaluating the long term durability and structural adequacy of encapsulated modules. Field testing, accelerated stress testing, and design studies have demonstrated that encapsulation materials, processes, and configurations are available that meet the FSA cost and performance goals.

Cuddihy, E.↗
NASA NTRS1987

Prediction of transition on a flat plate under the influence of free-stream turbulence using low-Reynolds-number two-equation turbulence models

The prediction characteristics and capabilities of two popular two-equation low-Reynolds-number turbulence models (Jones, Launder 1972; Lam, Bremhorst 1981) have been evaluated with respect to the prediction of transition of a flat plate under the influence of free-stream turbulence. The sensitivity of the predictions to free-stream turbulence intensity, initial starting location of the calculation, and the assumed initial starting profiles for k and epsilon has been determined and presented. Although both models predict the correct qualitative characteristics of transition, they also exhibit significant quantitative deficiencies with regard to both the predicted location and the length of transition. A modification to the production term in the turbulent kinetic energy equation is proposed which is based on a simple stability criterion and correlated to the free-stream turbulence level. The modification becomes inactive in the fully turbulent regime, but is shown to improve both the qualitative and quantitative characteristics of the transition predictions.

Schmidt, Rodney C.↗