Search NASA⌕ Search

SEARCH · Search NASA

Results for “POWER FACTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

The Impact of Inverter Dead-Time in Single-Phase Wireless Power Transfer Systems

In this paper, the effect of the dead-time on a single-phase wireless power transfer system is studied in detail. In practice, the dead-time is always placed between the complementary switching pulses of the inverter phase-leg. At higher operating frequencies, the dead-time issues in the resonant inverter become critical, especially as the power level increases. The detailed analysis of the dead-time on a wireless power transfer system is discussed for different operating conditions of the inverter duty-cycle and power factor. The switching characteristics of the wireless power transfer system inverter are analyzed, and the notch phenomenon that appears at the output of the inverter is also discussed. A notch equation based on the observations is derived to predict the notch occurrence during the system operation. Furthermore, the mathematical expressions are presented for different notch conditions. Subsequently, the effect of the notches on the sensitivity and the power transfer of the series-series compensated wireless power transfer system is analyzed. Finally, the approach is verified experimentally on an 8 kW wireless power transfer system prototype, and the results are compared with the theoretical analysis.

42 ENGINEERING↗

Demonstration of Essential Reliability Services by a 300-MW Solar Photovoltaic Power Plant

The California Independent System Operator (CAISO), First Solar, and the National Renewable Energy Laboratory (NREL) conducted a demonstration project on a large utility-scale photovoltaic (PV) power plant in California to test its ability to provide essential ancillary services to the electric grid. With increasing shares of solar- and wind-generated energy on the electric grid, traditional generation resources equipped with automatic governor control (AGC) and automatic voltage regulation controls -- specifically, fossil thermal -- are being displaced. The deployment of utility-scale, grid-friendly PV power plants that incorporate advanced capabilities to support grid stability and reliability is essential for the large-scale integration of PV generation into the electric power grid, among other technical requirements. A typical PV power plant consists of multiple power electronic inverters and can contribute to grid stability and reliability through sophisticated 'grid-friendly' controls. In this way, PV power plants can be used to mitigate the impact of variability on the grid, a role typically reserved for conventional generators. In August 2016, testing was completed on First Solar's 300-MW PV power plant, and a large amount of test data was produced and analyzed that demonstrates the ability of PV power plants to use grid-friendly controls to provide essential reliability services. These data showed how the development of advanced power controls can enable PV to become a provider of a wide range of grid services, including spinning reserves, load following, voltage support, ramping, frequency response, variability smoothing, and frequency regulation to power quality. Specifically, the tests conducted included various forms of active power control such as AGC and frequency regulation; droop response; and reactive power, voltage, and power factor controls. This project demonstrated that advanced power electronics and solar generation can be controlled to contribute to system-wide reliability. It was shown that the First Solar plant can provide essential reliability services related to different forms of active and reactive power controls, including plant participation in AGC, primary frequency control, ramp rate control, and voltage regulation. For AGC participation in particular, by comparing the PV plant testing results to the typical performance of individual conventional technologies, we showed that regulation accuracy by the PV plant is 24-30 points better than fast gas turbine technologies. The plant's ability to provide volt-ampere reactive control during periods of extremely low power generation was demonstrated as well. The project team developed a pioneering demonstration concept and test plan to show how various types of active and reactive power controls can leverage PV generation's value from being a simple variable energy resource to a resource that provides a wide range of ancillary services. With this project's approach to a holistic demonstration on an actual, large, utility-scale, operational PV power plant and dissemination of the obtained results, the team sought to close some gaps in perspectives that exist among various stakeholders in California and nationwide by providing real test data.

14 SOLAR ENERGY↗

Interim Evaluation of State-of-the-Art Controllers for Low-Power Stirling Generators for Space Applications

Stirling convertors use a linear alternator to extract power from the piston motion; this requires a coil and a magnet (Faraday’s law). The coil introduces unwanted phase shift to degrade power output as well as introduce instability; i.e., low power factor. Tuning capacitor is added to increase power output and stability; widely accepted that tuning capacitor value will affect both the power output and stability.

Free-Piston Stirling Convertor Controller↗

Electronic and thermoelectric properties of few-layer transition metal dichalcogenides

The electronic and thermoelectric properties of one to four monolayers of MoS{sub 2}, MoSe{sub 2}, WS{sub 2}, and WSe{sub 2} are calculated. For few layer thicknesses, the near degeneracies of the conduction band K and Σ valleys and the valence band Γ and K valleys enhance the n-type and p-type thermoelectric performance. The interlayer hybridization and energy level splitting determine how the number of modes within k{sub B}T of a valley minimum changes with layer thickness. In all cases, the maximum ZT coincides with the greatest near-degeneracy within k{sub B}T of the band edge that results in the sharpest turn-on of the density of modes. The thickness at which this maximum occurs is, in general, not a monolayer. The transition from few layers to bulk is discussed. Effective masses, energy gaps, power-factors, and ZT values are tabulated for all materials and layer thicknesses.

36 MATERIALS SCIENCE↗

Effect of anion and cation substitution in tungsten disulfide and tungsten diselenide on conductivity and thermoelectric power

The temperature dependences of the conductivity and thermoelectric power for a series of samples W{sub 1–x}Nb{sub x}S{sub 2}, W{sub 1–x}Nb{sub x}Se{sub 2}, WS{sub 2–y}Se{sub y}, W{sub 1–x}Nb{sub x}S{sub 2–y}Se{sub y} are studied at low temperatures. It is found that the cation substitution of W atoms with Nb leads to an increase in the conductivity and a decrease in the thermoelectric power. The anion substitution of S with Se atoms results in a simultaneous increase in the conductivity and thermoelectric power. The highest power factor among the samples studied is inherent to W{sub 0.8}Nb{sub 0.2}Se{sub 2}.

36 MATERIALS SCIENCE↗

Transport and thermoelectric properties in Copper intercalated TiS{sub 2} chalcogenide

We report on the thermoelectric properties of Cu{sub x}TiS{sub 2} bulk compounds. Copper cations have been intercalated into the layered chalcogenide TiS{sub 2} by spark plasma sintering. X-ray diffraction analysis coupled to transmission electron microscopy shows that the lattice constant c expands linearly as the Cu content x increases. The Cu-intercalation into TiS{sub 2} leads to substantial decrease in both electrical resistivity and lattice thermal conductivity as compared to those of pristine TiS{sub 2}. The figure of merit, ZT, is increased up to 0.45 at 800 K for x = 0.02. The power factor, PF, reaches 1.7 mW/mK{sup 2} in TiS{sub 2} at 325 K.

36 MATERIALS SCIENCE↗

The First-Principle Study of the Electronic Structure, Ferromagnetic and Thermoelectric Properties of Spinel Alloy FeAl{sub 2}O{sub 4} Using mBJ Functional Approach

In this research work, the modified Becke and Johnson potential has been used to realize the actual electronic states and band gap properties of FeAl{sub 2}O{sub 4}. Ferromagnetism is illustrated in terms of John-Teller energy and exchange energies involved in the system due to electron spin. Moreover, the exchange constants also support the ferromagnetism in the studied compound. The reduction of the magnetic moment of Fe from its free space value and the shifting of the magnetic moment to nonmagnetic sites are the consequence of strong magnetization. In the end, the electrical conductivity and Seebeck coefficient incorporated to give a high value of the power factor and thermal efficiency for energy renewable devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Magnetothermoelectric figure of merit of Co/Cu multilayers

The switching of the magnetic configuration of giant magnetoresistance multilayers not only changes the electrical and thermal conductivities but also the thermopower. We study the magnetotransport and the magnetothermoelectric properties of Co/Cu multilayer devices in a lateral thermal gradient. The Seebeck coefficient reaches values up to −18 μV/K at room temperature and shows a magnetic field dependence up to 28.6% upon spin reversal. In combination with thermal conductivity data of the same Co/Cu stack, we find a magnetothermoelectric figure of merit of up to 65%. Furthermore, a magneto-power factor of up to 110% is derived.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

In-situ Condition Monitoring of Components in Small Modular Reactors Using Process and Electrical Signature Analysis. Final report, volume 1. Development of experimental flow control loop, data analysis and plant monitoring

The research and development under this project was focused on the following three major objectives: Objective 1: Identification of critical in-vessel SMR components for remote monitoring and development of their low-order dynamic models, along with a simulation model of an integral pressurized water reactor (iPWR). Objective 2: Development of an experimental flow control loop with motor-driven valves and pumps, incorporating data acquisition and on-line monitoring interface. Objective 3: Development of stationary and transient signal processing methods for electrical signatures, machinery vibration, and for characterizing process variables for equipment monitoring. This objective includes the development of a data analysis toolbox. The following is a summary of the technical accomplishments under this project: - A detailed literature review of various SMR types and electrical signature analysis of motor-driven systems was completed. A bibliography of literature is provided at the end of this report. Assistance was provided by ORNL in identifying some key references. - A review of literature on pump-motor modeling and digital signal processing methods was performed. - An existing flow control loop was upgraded with new instrumentation, data acquisition hardware and software. The upgrading of the experimental loop included the installation of a new submersible pump driven by a three-phase induction motor. All the sensors were calibrated before full-scale experimental runs were performed. - MATLAB-Simulink model of a three-phase induction motor and pump system was completed. The model was used to simulate normal operation and fault conditions in the motor-pump system, and to identify changes in the electrical signatures. - A simulation model of an integral PWR (iPWR) was updated and the MATLAB-Simulink model was validated for known transients. The pump-motor model was interfaced with the iPWR model for testing the impact of primary flow perturbations (upsets) on plant parameters and the pump electrical signatures. Additionally, the reactor simulation is being used to generate normal operation data and data with instrumentation faults and process anomalies. A frequency controller was interfaced with the motor power supply in order to vary the electrical supply frequency. The experimental flow control loop was used to generate operational data under varying motor performance characteristics. Coolant leakage events were simulated by varying the bypass loop flow rate. The accuracy of motor power calculation was improved by incorporating the power factor, computed from motor current and voltage in each phase of the induction motor.- A variety of experimental runs were made for steady-state and transient pump operating conditions. Process, vibration, and electrical signatures were measured using a submersible pump with variable supply frequency. High correlation was seen between motor current and pump discharge pressure signal; similar high correlation was exhibited between pump motor power and flow rate. Wide-band analysis indicated high coherence (in the frequency domain) between motor current and vibration signals. - Wide-band operational data from a PWR were acquired from AMS Corporation and used to develop time-series models, and to estimate signal spectrum and sensor time constant. All the data were from different pressure transmitters in the system, including primary and secondary loops. These signals were pre-processed using the wavelet transform for filtering both low-frequency and high-frequency bands. This technique of signal pre-processing provides minimum distortion of the data, and results in a more optimal estimation of time constants of plant sensors using time-series modeling techniques.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Highly efficient small form factor LED retrofit lamp

This report summarizes work to develop a high efficiency LED-based MR16 lamp downlight at OSRAM SYLVANIA under US Department of Energy contract DE-EE0000611. A new multichip LED package, electronic driver, and reflector optic were developed for these lamps. At steady-state, the lamp luminous flux was 409 lumens (lm), luminous efficacy of 87 lumens per watt (LPW), CRI (Ra) of 87, and R9 of 85 at a correlated color temperature (CCT) of 3285K. The LED alone achieved 120 lumens per watt efficacy and 600 lumen flux output at 25 C. The driver had 90% electrical conversion efficiency while maintaining excellent power quality with power factor >0.90 at a power of only 5 watts. Compared to similar existing MR16 lamps using LED sources, these lamps had much higher efficacy and color quality. The objective of this work was to demonstrate a LED-based MR16 retrofit lamp for replacement of 35W halogen MR16 lamps having (1) luminous flux of 500 lumens, (2) luminous efficacy of 100 lumens per watt, (3) beam angle less than 40° and center beam candlepower of at least 1000 candelas, and (4) excellent color quality.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Process dependent thermoelectric properties of EDTA assisted bismuth telluride

Comparison between the structure and thermoelectric properties of EDTA (Ethylene-diamine-tetra-acetic acid) assisted bismuth telluride prepared by electrochemical deposition and hydrothermal route is reported in the present work. The prepared samples have been structurally characterized by high resolution X-ray diffraction spectra (HRXRD), field emission scanning electron microscopy (FESEM) and high resolution transmission electron microscopic images (HRTEM). Crystallite size and strain have been determined from Williamson-Hall plot of XRD which is in conformity with TEM images. Measurement of transport properties show sample in the pellet form (S{sub 1}) prepared via hydrothermal route has higher value of thermoelectric power (S) than the electrodeposited film (S{sub 2}). But due to a substantial increase in the electrical conductivity (σ) of the film (S{sub 2}) over the pellet (S{sub 1}), the power factor and the figure of merit is higher for sample S{sub 2} than the sample S{sub 1} at room temperature.

36 MATERIALS SCIENCE↗

Systematic DFT study of the impact of anionic variations on the physical properties of Cd1-xMnxX (XS, Se, Te; x = 6.25%)

Highlights: • The structural and electronic properties are investigated with most accurate mBJ potential. • The FM state stability is illustrated for Cd{sub 0.9375}Mn{sub 0.0625}S/Se/Te DMSs. • The FM semiconducting nature depicts potential applications in magneto-optic applications. • The absorption shifts within the visible range with S to Te variation that is verified by E{sub g}. • Thermoelectric properties indicate dominant hole-carriers and suitability at high temperatures. - Abstract: The structural and electronic properties are theoretically investigated for Cd{sub 1-x}Mn{sub x}X (XS, Se, Te; x = 6.25%) diluted magnetic semiconductors, which are further employed for extracting the magnetic, optical and thermoelectric properties using modified-Becke-Johnson (mBJ) potential. Ferromagnetic state stability is confirmed through the computed enthalpy of formation and the cohesive energies. The electronic properties elucidate Cd{sub 1-x}Mn{sub x}X (XS, Se, Te; x = 6.25%) as ferromagnetic semiconductors because both spin channels have Fermi energy level (E{sub F}) within the band gap, depicting potential applications in spintronic devices. The calculated optical response indicates shifts in the absorption within the visible energy that is consistent with the computed direct band gap values (1.9 eV–3.1 eV). Thermoelectric properties observed within 200 K–800 K show positive Seebeck coefficient indicating holes as majority charge carriers. Although Mn-doping suppresses the power factor, however, it improves with temperature, showing a potential for optimizing the thermoelectric performance.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Oxygen Pressure on Thermoelectric Properties of p-Type CuAlO{sub 2} Films Fabricated by Pulsed Laser Deposition

We focus on the growth of p-type CuAlO{sub 2} thin films and its thermoelectric properties. Thin films are deposited by pulsed laser deposition technique on single-crystal sapphire substrates varying the oxygen partial pressure. Thin film deposited at oxygen partial pressure of 200 mTorr presents bigger grains (about 10 μm in size) and shows Seebeck coefficient as high as 270 µV/K with a conductivity of about 0.8 S/cm so that its power factor is about 5.7 µW/mK{sup 2} at 800 K, twice than observed in the film deposited at 60 mTorr of oxygen.

36 MATERIALS SCIENCE↗

Uncertainty quantification and sensitivity analysis applications to fuel performance modeling

Best-estimate fuel performance codes such as BISON currently under development at the Idaho National Laboratory, utilize empirical and mechanistic lower-length-scale informed correlations to predict fuel behavior under normal operating and accident reactor conditions. Traditionally, best-estimate results are presented using the correlations with no quantification of the uncertainty in the output metrics of interest. However, there are associated uncertainties in the input parameters and correlations used to determine the behavior of the fuel and cladding under irradiation. Therefore, it is important to perform uncertainty quantification and include confidence bounds on the output metrics that take into account the uncertainties in the inputs. In addition, sensitivity analyses can be performed to determine which input parameters have the greatest influence on the outputs. In this paper we couple the BISON fuel performance code to the DAKOTA uncertainty analysis software to analyze a representative fuel performance problem. The case studied in this paper is based upon rod 1 from the IFA-432 integral experiment performed at the Halden Reactor in Norway. The rodlet is representative of a BWR fuel rod. The input parameters uncertainties are broken into three separate categories including boundary condition uncertainties (e.g., power, coolant flow rate), manufacturing uncertainties (e.g., pellet diameter, cladding thickness), and model uncertainties (e.g., fuel thermal conductivity, fuel swelling). Utilizing DAKOTA, a variety of statistical analysis techniques are applied to quantify the uncertainty and sensitivity of the output metrics of interest. Specifically, we demonstrate the use of sampling methods, polynomial chaos expansions, surrogate models, and variance-based decomposition. The output metrics investigated in this study are the fuel centerline temperature, cladding surface temperature, fission gas released, and fuel rod diameter. The results highlighted the importance of the thermal conductivity of the fuel, the thermal conductivity of the cladding, the gap thickness, the fuel thermal expansion, and the system power factor as influential parameters.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermoelectric properties of doped BaHfO{sub 3}

We have studied the structural stability, electronic structure, optical properties and thermoelectric properties of doped BaHfO{sub 3} by full potential linearized augmented plane wave (FP-LAPW) method. The electronic structure of BaHfO{sub 3} doped with Sr shows enhances the indirect band gaps of 3.53 eV, 3.58 eV. The charge density plots show strong ionic bonding in Ba-Hf, and ionic and covalent bonding between Hf and O. Calculations of the optical spectra, viz., the dielectric function, refractive index and extinction coefficient are performed for the energy range are calculated and analyzed. Thermoelectric properties of semi conducting are also reported first time. The doped BaHfO{sub 3} is approximately wide band gap semiconductor with the large p-type Seebeck coefficient. The power factor of BaHfO{sub 3} is increased with Sr doping, decreases because of low electrical resistivity and thermal conductivity.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Ab Initio Study of Electronic, Magnetic, and Thermoelectric Response of ZTi{sub 2}O{sub 4} (Z = Mg, Zn, and Cd) Through mBJ Potential

The electronic, magnetic, and thermoelectric properties of ZTi{sub 2}O{sub 4} (Z = Mg, Zn, and Cd) spinel oxides are analyzed by applying DFT approach. The band structure (BS) and density of states (DOS) illustrate a ferromagnetic state due to the evident exchange splitting leading to the energy shift in the spin-polarized sub-bands. Furthermore, ferromagnetic state stability is also justified through the computed crystal field, Jahn-Teller, and exchange energies. The exchange energy exceeding the crystal field energy reveals that ferromagnetism is mediated due to electrons, which is also consistent with the computed negative indirect exchange energy. Using BoltzTraP code, thermoelectric investigation illustrate that Mg, Zn, and Cd cations can tune the optimum power factor to intermediate and higher temperatures, which suggests potential energy harvesting applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermoelectric properties of CuS/Ag{sub 2}S nanocomposites synthesed by modified polyol method

This is the report on successful synthesis of Ag doped CuS nanostructures by modified polyol method. The resulting samples were characterized by powder X-ray diffraction (XRD), energy dispersive X-ray (EDX), atomic force microscopy (AFM) and dynamic light scattering (DLS). Particle size of pure CuS nanoparticles (NPs) was 17 nm, 38 nm and 97 nm as determined from Scherrer formula, AFM and DLS, respectively. Introduction of Ag led to formation of CuS/Ag{sub 2}S composites. A transition at 55 K in thermopower is ascribed to structural transformation from hexagonal to orthorhombic structure. Further, their thermoelectric properties exhibit remarkable change owing to Ag doping in CuS nanostructures. The power factor improves with increasing Ag content. They reveal that CuS/Ag{sub 2}S nanocomposites are some of the potential candidates for generation of thermoelectricity in future.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Structural, electrical, and thermoelectrical properties of (Bi{sub 1-x}Sb{sub x}){sub 2}Se{sub 3} alloys prepared by a conventional melting technique

Polycrystalline solid solutions of (Bi{sub 1-x}Sb{sub x}){sub 2}Se{sub 3} (x = 0, 0.025, 0.050, 0.075, 0.100) were prepared using a facile method based on the conventional melting technique followed by annealing process. X-ray analysis and Raman spectroscopical measurements revealed formation of Bi{sub 2}Se{sub 3} in single phase. The electrical and thermoelectric properties have been studied on the bulk samples in the temperature range 100-420 K. The electrical conductivity measurements show that the activation energy and room-temperature electrical conductivity dependences on the Sb content respectively exhibit minimum and maximum values at x = 0.05. The thermoelectric power exhibited a maximum value near the room temperature suggesting promising materials for room-temperature applications. The highest power factor value was found to be 13.53 {mu}W K{sup -2} cm{sup -1} and recorded for the x = 0.05 compound.

36 MATERIALS SCIENCE↗