Search NASA⌕ Search

SEARCH · Search NASA

Results for “REFLECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Anti-reflection coating with mullite and Duroid for large-diameter cryogenic sapphire and alumina optics

We developed a broadband two-layer anti-reflection (AR) coating for use on a sapphire half-wave plate (HWP) and an alumina infrared (IR) filter for the cosmic microwave background (CMB) polarimetry. Measuring the faint CMB B-mode signals requires maximizing the number of photons reaching the detectors and minimizing spurious polarization due to reflection with an off-axis incident angle. Sapphire and alumina have high refractive indices of 3.1 and are highly reflective without an AR coating. This paper presents the design, fabrication, quality control, and measured performance of an AR coating using thermally sprayed mullite and Duroid 5880LZ. This technology enables large optical elements with diameters of 600 mm. We also present a thermography-based nondestructive quality control technique, which is key to assuring good adhesion and preventing delamination when thermal cycling. We demonstrate the average reflectance of about 2.6% (0.9%) for two observing bands centered at 90/150 (220/280) GHz. At room temperature, the average transmittance of a 105 mm square test sample at 220/280 GHz is 83%, and it will increase to 90% at 100 K, attributed to reduced absorption losses. Therefore, our developed layering technique has proved effective for 220/280 GHz applications, particularly in addressing dielectric loss concerns. This AR coating technology has been deployed in the cryogenic HWP and IR filters of the Simons Array and the Simons observatory experiments and applies to future experiments such as CMB-S4.

Sakaguri, Kana (ORCID:0000000156678118)↗

Temporal reflection of an optical pulse from a short soliton: impact of Raman scattering

We study temporal reflection of an optical pulse from the refractive-index barrier created by a short pump soliton inside a nonlinear dispersive medium such as an optical fiber. One feature is that the soliton’s speed changes continuously as its spectrum redshifts because of intrapulse Raman scattering. We use the generalized nonlinear Schrödinger equation to find the shape and spectrum of the reflected pulse. Both are affected considerably by the soliton’s trajectory. The reflected pulse can become considerably narrower compared to the incident pulse under conditions that involve a type of temporal focusing. This phenomenon is explained through space–time duality by showing that the temporal situation is analogous to an optical beam incident obliquely on a parabolic mirror. We obtain an approximate analytic expression for the reflected pulse’s spectrum and use it to derive the temporal version of the transformation law for the

47 OTHER INSTRUMENTATION↗

Time reflection of light from a quantum perspective and vacuum entanglement

If a boundary between two static media is moving with a constant superluminal velocity, or there is a sudden change of the refractive index with time, this yields generation of entangled pairs of photons out of vacuum propagating in the opposite directions. Here we show that during this process, entanglement of Minkowski vacuum is transferred to the entanglement of the generated photon pairs. If initially an electromagnetic pulse is present in the medium the photon generation is stimulated into the pulse mode, and since photons are created as entangled pairs the counter-propagating photon partners produce a pulse moving in the opposite direction, which is known as time reflection. Thus, time reflection occurs due to stimulated generation of the entangled photon pairs out of entangled vacuum and no photons in the original pulse are in fact being reflected. This is different from the mechanism of light reflection from spatial inhomogeneities for which no photons are generated.

Optics↗

Using MCNP6 to Estimate Fission Neutron Properties of a Reflected Plutonium Sphere

The purpose of this project was to determine the fission multiplicity distribution, p(v), for the Beryllium Reflected Plutonium (BeRP) ball and to determine whether or not it changed appreciably for various High Density Polyethylene (HDPE) reflected configurations. The motivation for this project was to determine whether or not the average number of neutrons emitted per fission, v, changed significantly enough to reduce the discrepancy between MCNP6 and Robba, Dowdy, Atwater (RDA) point kinetic model estimates of multiplication. The energy spectrum of neutrons that induced fissions in the BeRP ball, NIF (E), was also computed in order to determine the average energy of neutrons inducing fissions, NIF . p(v) was computed using the FMULT card, NIF (E) and NIF were computed using an F4 tally with an FM tally modifier (F4/FM) card, and the multiplication factor, k eff , was computed using the KCODE card. Although NIF (E) changed significantly between bare and HDPE reflected configurations of the BeRP ball, the change in p(v), and thus the change in v, was insignificant. This is likely due to a difference between the way that NIF is computed using the FMULT and F4/FM cards. The F4/FM card indicated that NIF (E) was essentially Watt-fission distributed for a bare configuration and highly thermalized for all HDPE reflected configurations, while the FMULT card returned an average energy between 1 and 2 MeV for all configurations, which would indicate that the spectrum is Watt-fission distributed, regardless of the amount of HDPE reflector. The spectrum computed with the F4/FM cards is more physically meaningful and so the discrepancy between it and the FMULT card result is being investigated. It is hoped that resolving the discrepancy between the FMULT and F4/FM card estimates of NIF(E) will provide better v estimates that will lead to RDA multiplication estimates that are in better agreement with MCNP6 simulations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Spread Spectrum Time Domain Reflectivity for String Monitoring in PV Power Plants (Final Technical Report)

This final report describes the methods and results of applying Spread Spectrum Time Domain Reflectivity (SSTDR) for String Monitoring in PV Power Plants for DE-EE0008169. The project created a new system for both detecting and locating electrical faults in photovoltaic systems. In this work, we address photovoltaic electric faults that are both common and costly. Based on interviews with photovoltaic power plant owners, operators, and maintainers, three types of faults are common and of significant interest: disconnects, ground faults, and arc faults. Disconnects can originate from many sources. They are often due to everyday events, such as lawnmowing (accidentally running over a cable), animals eating through the cables, or degradation that occurs over time due to corrosion or general degradation. Ground faults occur when the cables (for example, due to frayed insolation) connect to the ground, relaying current into the ground. These faults are particularly problematic since the ground faults are often intermittent. That is, ground faults commonly appear during rain storms due to a change in soil conductivity and then disappear when the rain ends. This makes the ground fault difficult to find because while current systems can detect the overall change in voltage and current associated with a ground fault, technicians are necessary to locate the fault. As a result, ground faults may disappear before the technician arrives at the power plant. Hence, locating and fixing ground faults often require multiple trips. We also study arc faults, which can result when nearby conductors create an arc of electrical current through the air. While less common, arc faults can be extremely dangerous. The energetic electrical arc can cause fires and destroy equipment, costing significant damage. Overall all three types of faults cost owners and operators money, either from the destruction of equipment or from technician time. Furthermore, while devices exist for detecting ground faults (ground fault circuit interrupters) and arc faults (arc fault circuit interrupter), these systems only search patterns of electrical current that correspond to each fault. This information cannot be used to locate the fault. In addition, these protection systems experience nuisance trips due to nearby electromagnetic interference, such as from a lawn mower or other motors that produce significant amounts of electromagnetic radiation. Hence, the overall goal of this project is to create an SSTDR tool that provides photovoltaic power plants with more reliable fault detection in addition to the localization of faults. SSTDR works by transmitting electrical signals into the photovoltaic string. Those signals reflect from impedance discontinuities (i.e., disconnects, ground faults, and arc faults). These faults are then detected by measuring the presence of a reflection at the SSTDR and can be located by identifying the location of that reflection in time. In addition, unlike current protection systems, these systems do not experience nuisance trips since their low amplitude, high frequency, and coded signal can by analyzed without interference from the regular operational voltage on the photovoltaic string.

14 SOLAR ENERGY↗

Improvements in Mirror Surface Measurement with Reflected Computer Vision Targets

Over the last several years, NREL has been developing a system to measure large optical surfaces of heliostat mirrors by reflecting computer vision targets. An advantage of this system, called Reflected Target Nonintrusive Assessment (ReTNA), is that it lends itself well to stitching together many images, each reflecting only part of a larger heliostat. In the last few months, this was taken to a new extreme, with a small target (<5m2) being used to measure a >25m2 long focal length heliostat. These measurements were compared with traditional fringe deflectometry methods, which require a >50m2 target, and photogrammetry. The strengths, weaknesses and limitations of ReTNA are discussed. An estimated uncertainty in this new measurement is presented, along with software improvements and a new wireless data collection system. A bill of materials for this measurement system is presented, which has been designed to use all low-cost, off-the-shelf components. Finally, the next steps for future ReTNA development are presented. Overall, ReTNA can be a valuable optics measurement system, complimentary to existing measurement techniques available for large reflective surfaces.

14 SOLAR ENERGY↗

The Dark World: A Tale of WASP-43b in Reflected Light with HST WFC3/UVIS

Optical reflected light eclipse observations provide a direct probe of exoplanet scattering properties, such as from aerosols. We present here the photometric reflected light observations of WASP-43b using the Hubble Space Telescope (HST) WFC3/UVIS instrument with the F350LP filter (346–822 nm) encompassing the entire optical band. This is the first reflected light photometric eclipse using UVIS in scanning mode; as such, we further detail our scanning extraction and analysis pipeline Arctor. Our HST WFC3/UVIS eclipse light curve for WASP-43b derived a 3σ upper limit of 67 ppm on the eclipse depth, which implies that WASP-43b has a very dark dayside atmosphere. With our atmospheric modeling campaign, we compared our reflected light constraints with predictions from global circulation and cloud models benchmarked with HST and Spitzer observations of WASP-43b. We infer that we do not detect clouds on the dayside within the pressure levels probed by HST WFC3/UVIS with the F350LP filter (P > 1 bar). This is consistent with the general circulation model predictions based on previous WASP-43b observations. Dayside emission spectroscopy results from WASP-43b with HST and Spitzer observations are likely to not be significantly affected by contributions from cloud particles.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Calibrating radar wind profiler reflectivity factor using surface disdrometer observations

Abstract. This study uses surface disdrometer reflectivity factor estimates to calibrate the vertical and off-vertical pointing radar beams produced by an ultra high frequency (UHF) band radar wind profiler (RWP) deployed at the US Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) program Southern Great Plains (SGP) Central Facility in northern Oklahoma from April 2011 through July 2019. The methodology consists of five steps. First, the recorded Doppler velocity power spectra are adjusted to account for Nyquist velocity aliasing and coherent integration filtering effects. Second, the spectrum moments are calculated. The third step increases the signal-to-noise ratio (SNR) due to inflated noise power estimates during convective rain events that cause SNR to be biased low. The fourth step determines the RWP calibration constant for one radar beam (called the “reference” beam) by comparing uncalibrated RWP reflectivity factors at 500 m above the ground to 1 min resolution surface disdrometer reflectivity factors. The last step uses the calibrated reference beam reflectivity factor to calibrate the other radar beams during precipitation. There are two key findings. The RWP sensitivity decreased by approximately 3 to 4 dB yr−1 as the hardware aged. This drift was slow enough that the reference calibration constant can be estimated over 3-month intervals using episodic rain events. The calibrated moments are available on the DOE ARM data archive, and the Python processing code is available on public repositories.

54 ENVIRONMENTAL SCIENCES↗

Design and development of laser damage resistant low group delay dispersion optical coatings for high reflection at 45o incidence P polarization and wavelengths from 800 to 1000 nm.

This paper describes the modelling and design development of an optical coating that is suitable for broad bandwidth high reflection (BBHR) at 45° angle of incidence (AOI), P polarization (Ppol) and fs-class laser pulses whose frequencies correspond to wavelengths from 800 to 1000 nm, and that can eventually be produced uniformly on meter-class optical substrates. The coating design process was guided by specifications of not only high reflection but also high laser-induced damage threshold (LIDT) as well as low group delay dispersion (GDD) for reflected light over the broad, 200 nm bandwidth in order to minimize temporal broadening of the fs pulses upon reflection. The coating is based on TiO 2 /SiO 2 layer pairs by means of e-beam evaporation with ion-assisted deposition (IAD). We used OptiLayer Thin Film Software to explore coating designs with a limited optimization process starting from TiO 2 /SiO 2 layer pairs with layer thicknesses in an opposite “chirp” arrangement. This approach proved to be successful, leading to a design with R > 99.5% from 801 – 999 nm and GDD < 20 fs 2 from 843 – 949 nm (45° AOI, Ppol). The GDD behaves in a smooth way that lends itself to compensation of GDD effects. Also, the electric field intensities are favorable to high LIDT in that they quench rapidly into the outer coating layers or are of moderate strength, or they are located in the higher band gap SiO 2 layers.

36 MATERIALS SCIENCE↗

Titanium and Aluminum Rod-Replacement Experiments in Fully-Reflected 6.90% Enriched UO{sub 2} Fuel Rod Lattices

The Seven Percent Critical Experiment (7uPCX) was designed to provide benchmark criticality and reactor physics data for water-moderated pin-fueled nuclear reactor cores. The enrichment of the fuel was chosen to explore the enrichment range above the current 5% ceiling for US commercial pressurized water reactors. The experiment was part of the US Department of Energy (DOE) Nuclear Energy Research Initiative Project 01-124 titled 'Reactor Physics and Criticality Benchmark Evaluations for Advanced Nuclear Fuel'. Three sets of benchmark experiments have been completed using the 7uPCX and documented as LEUCOMP-THERM-080, LEU-COMP-THERM-078, and LEUCOMP-THERM-096. The experiments for LEUCOMP-THERM-080 and LEU-COMP-THERM-078 were done in fully-reflected arrays with the number of fuel rods in the array as the approach parameter. The experiments for LEU-COMP-THERM-096 are similar to those in LEUCOMP-THERM-080 except that the arrays are partially-reflected - the arrays were larger than would be possible with full reflection and the approach-to-critical experiments were done with the depth of the water in the critical assembly as the approach parameter. The experiments described here are similar to the fully-reflected experiments in LEU-COMP-THERM-080 with some of the central fuel rods in the array replaced by titanium rods, aluminum rods, and/or water. The experiments are designed to provide criticality safety benchmarks with significant reactivity from titanium and equivalent configurations with aluminum experiment rods. These experiments are documented as LEU-COMP-THERM-097. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of Ti{sub 1-x}Al{sub x}N coatings with selective IR reflectivity

Ti{sub 1-x}Al{sub x}N thin films were deposited by reactive magnetron sputtering. The obtained different stoichiometries give rise to different optical properties as the films change from metallic to dielectric. In this work the IR reflectivity of these coatings is investigated taking into account different application fields for IR selective Ti{sub 1-x}Al{sub x}N thin films. Low Al content coatings present high reflectivity, high absorptance and low thermal emittance. High Al compositions give raise to coatings with high absorptance and high thermal emittance. The composition of the coatings was evaluated combining electron energy loss spectroscopy (EELS) and energy dispersive spectroscopy. Scanning electron microscopy (SEM) revealed a columnar structure. Reflectance spectra for the visible and infrared spectral ranges were used to obtain the solar absorptance and thermal emittance values, used to calculate the equilibrium temperature of the coatings. The thermal stability in air from 300 to 600 C was also evaluated. (author)

14 SOLAR ENERGY↗

Resonant reduction in microwave reflectivity from an overdense plasma with the employment of a parallel metal grating

A microwave normally incident on an overdense plasma is totally reflected. However, the presence of a thin metal grating parallel to the plasma surface greatly reduces the reflectivity when the grating wave number equals the wave number of the surface plasma wave on the plasma-free space interface at microwave frequency. The microwave induces an oscillatory current in the free electrons of the grating at the frequency of the microwave, {omega}, and wave number of the grating, q. This current resonantly excites a surface plasma wave (SPW) on the plasma surface. The diversion of microwave power into SPW severely reduces the microwave reflectivity.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Pulse compression radar reflectometry to measure electron density in plasma with parasitic reflections

Pulse compression radar reflectometry is used to obtain electron density profile in plasma with parasitic reflections in this article. The pulse compression radar relies on the relation between the temporal width of a pulse and the frequency bandwidth of this pulse: {delta}t{proportional_to}1/{delta}f. So a set of sweep-frequency microwaves within a bandwidth {delta}f can be introduced sequentially into the plasma to obtain the same information as the one obtained by a real pulse. By applying a Fourier transform to the data of reflectivity array in the frequency domain, the temporal response in the time domain is obtained. The limitation of the parasitic reflections on measurement can be eliminated from the temporal response by the method of time gate. This is a prominent advantage when this method is compared to the traditional reflectometry. For this method, an appropriate compromise between the spatial resolution and the electron density resolution is important. Experimental results show that the profile obtained from pulse compression radar reflectometry is similar to that from a double Langmuir probe.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Phototunable reflection notches of cholesteric liquid crystals

The reflection notch of cholesteric liquid crystals (CLCs) formed from highly photosenstive azobenzene nematic liquid crystals doped with light-insensitive, large helical twisting power chiral dopants is shown to be widely phototunable by green laser beams. The nonlinear transmission properties of these materials were studied. We have shown that the relative shift in Bragg wavelength is independent of the chiral dopant concentration and develop a predictive theory of such behavior. The theory describes the dynamics of phototuning as well. Reflection shifts greater than 150 nm were driven with low power, cw of 532 nm in these photosensitive CLCs, previously attainable only through UV pre-exposure. A nonlinear feedback mechanism was demonstrated for CLCs of left, right, and both handedness upon laser-induced blueshifting of the reflection notch from a red wavelength using a green cw laser.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Kramers-Kronig Analysis of Infrared Reflectance Spectra for Quaternary In{sub x}Al{sub y}Ga{sub 1-x-y}N Alloy

In this paper, a Kramers-Kronig (KK) analysis of infrared (IR) reflectance spectrum of quaternary In{sub 0.01}Al{sub 0.06}Ga{sub 0.93}N film grown by molecular beam epitaxy (MBE) is reported. The infrared measurement is performed in the reflection mode at an incident angle of 15 degree sign by Fourier transform infrared (FTIR) spectroscopy at T = 300 K. The Kramers-Kronig analysis of the reflectivity data has been used to obtain the real and imaginary parts of the index of refraction (n and k), and the real and imaginary parts of the dielectric response function ({epsilon}' and {epsilon}') of the materials. Finally, the transverse optical and longitudinal optical phonons for quaternary In{sub x}Al{sub y}Ga{sub 1-x-y}N were obtained.

36 MATERIALS SCIENCE↗

Development of a realistic photonic modeling for the evaluation of infrared reflections in the metallic environment of ITER

In nuclear fusion experiments, the plasma facing components are exposed to high heat fluxes and infrared (IR) imaging diagnostics are routinely used for surveying their surface temperature for preventing damages. However the future use of metallic components in the ITER tokamak adds complications in temperature estimation. Indeed, low and variable emissivity of the observed surface and the multiple reflections of the light coming from hot regions will have to be understood and then taken into account. In this paper, a realistic photonic modeling based on Monte Carlo ray-tracing codes is used to predict the global response of the complete IR survey system. This also includes the complex vessel geometry and the thermal and optical surface properties using the bidirectional reflectivity distribution function that models the photon-material interactions. The first results of this simulation applied to a reference torus are presented and are used as a benchmark to investigate the validity of the global model. Finally the most critical key model parameters in the reflected signals are identified and their contribution is discussed.

36 MATERIALS SCIENCE↗

Spectroscopic refractometer for transparent and absorbing liquids by reflection of white light near the critical angle

We propose and evaluate a spectroscopic refractometer device to measure the refractive index dispersion of transparent and absorbing solutions. The angle-dependent reflectivity of a white beam of light in an internal reflection configuration around the critical angle is spectrally analyzed. The refractive index in a wavelength range from 400 nm to 900 nm is obtained from the angle-reflectivity curve around the critical angle at each wavelength. The device does not use angle scanning mechanisms, decreasing considerably the complexity of the instrument in comparison to previous proposals. As a result, the measurements are obtained relatively fast. Nevertheless, a good experimental resolution in refractive index of about {Delta}n Almost-Equal-To 10{sup -4} at all the wavelengths is achieved in the case of transparent solutions. The calibration procedure of the device is discussed in detail. We also present measurements of the refractive index dispersion of rhodamine 6G-methanol solutions, which has a strong absorption band in the visible spectra.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Chemical selective microstructural analysis of thin film using resonant x-ray reflectivity

Strong modulations of the reflected x-ray intensities near the respective absorption edges of the constituent materials promise to determine layer composition of thin film structures along with spectroscopic like information. Near the absorption edge, the orders of magnitude more contrast beyond the pure electron density distributions of materials find an approach to overcome the low density difficulty of the conventional x-ray reflectivity technique. These aspects are explained by experimental studies on partially decomposed boron nitride thin films. Chemical composition profile is determined from free surface to the embedded buried layer with depth resolution in nanometer scale. The results of resonant reflectivity for chemical analysis are correlated with depth dependent x-ray photo electron spectroscopy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗