SEARCH · Search NASA

Results for “Radio Frequency Interference”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

NASA NTRS1985

The northern Utah satellite (NUSAT) communications link

During the planning Stages of the NUSAT satellite, an obvious issue to be discussed was the method of communications to be used. The frequencies would have to be high enough to pass through the atmosphere relatively unattenuated but low enough that antennas and transmission lines would not be so critical in length and properties that unexperienced students would have difficulty with handling them. In conversations with the Federal Communications Commission (FCC) in Washington D.C., the frequencies of 450.000 MHz and 137.900 MHz were decided upon and applied for licensing. The 450.000 MHt up-link is used on a "non-interference" basis to control the satellite while the 137.900 MHz frequency down-links data from the satellite. A reasonable amount of time was spent discussing the mods of transmission to be used in communication with the satellite. Representatives of the amateur radio satellite organization, AMSAT, were contacted for ides. This organization seems to favor AM types of emissions such as CW to control their OSCAR series of satellites and also the current Phase 111 unit. NUSAT personnel felt, however, that there would be merit in the improved signal to noise ratio usually obtained in an FM mode. Doppler shift of the transmitted information on the NUSAT also had to be considered. The final decision WBS to use Audio Frequency Shift Keying (AFSK) modulated on an FM carrier. In this mode the audio tones used would not shift frequency with Doppler - only the carrier would shift in frequency. If necessary, the receivers could be fitted with a form of AFC control or simply have enough bandwidth to handle the Doppler shift with an acceptable increase in noise.

Lee Barrett↗

NASA NTRS1981

Fundamental limitations caused by RF propagation

Propagation phenomena affect the design of radio frequency (RF) transmission systems. Propagation phenomena limit the suitability of portions of the frequency band for some applications, limit the reliability of RF transmission systems, and provide a means of coupling unwanted signals from one system to another with the potential of producing interference. The possibility of interference is the fundamental limitation to the unrestricted use of the frequency band. Phenomena affecting suitability, reliability, and the potential for interference are considered for frequencies in the 1- to 300-GHz range.

Crane, R. K.↗

NASA NTRS1982

A two-component rain model for the prediction of attenuation statistics

A two-component rain model has been developed for calculating attenuation statistics. In contrast to most other attenuation prediction models, the two-component model calculates the occurrence probability for volume cells or debris attenuation events. The model performed significantly better than the International Radio Consultative Committee model when used for predictions on earth-satellite paths. It is expected that the model will have applications in modeling the joint statistics required for space diversity system design, the statistics of interference due to rain scatter at attenuating frequencies, and the duration statistics for attenuation events.

Crane, R. K.↗

NASA NTRS1987

Phase closure with a rotational shear interferometer

A simple and efficient way is proposed for achieving phase closure in an optical telescope (to enable recovering Fourier transform phases that would otherwise be corrupted by atmospheric and instrumental errors), by means of rotational shear interferometry. In a rotational shear interferometer, one images the telescope aperture onto the interferometer and then interferes the aperture with itself in a rotated orientation. To achieve the maximum frequency content permitted by the telescope, the shear has to be 180 deg, but better dynamic range and SNR are possible for lower frequencies. Drawbacks of the proposed method compared to radio astronomy are noted, and different approaches are indicated as to how to collect and use the phase closure data. Phase closure can be realized on existing telescopes and existing interferometers with special modifications. Although not all base lines are possible, the extra constraints provided by the closure phases greatly reduce the ambiguity now existing in phaseless image reconstruction.

Ribak, Erez↗

NASA NTRS1990

The Lunar Observer Radio Astronomy Experiment (LORAE)

The paper proposes to place a simple low-frequency dipole antenna on board the Lunar Observer (LO) satellite. LO will orbit the moon in the mid-1990's, mapping the surface at high resolution and gathering new geophysical data. In its modest concept, LORAE will collect crucial data on the radio interference environment while on the near-side (to aid in planning future arrays) and will monitor bursts of emission from the sun and the Jovian planets. LORAE will also be capable of lunar occultation studies of greater than 100 of the brightest sources, gathering arcminute resolution data on sizes and measuring source fluxes. A low resolution all-sky map below 10 MHz, when combined with data from the Gamma-Ray Observatory, will uniquely determine the density of Galactic cosmic ray electrons and the strength of the Galaxy's magnetic field. LORAE also will be able to measure the density of the moon's ionosphere.

Burns, Jack O.↗

NASA NTRS1982

New CCIR papers on telecommunications for deep space research

Three draft reports submitted by JPL to the International Radio Consultative Committee (CCIR) for inclusion in their 1982 edition of reports and recommendations are presented. Potential interference between deep space telecommunications and the fixed satellite and broadcasting satellite services in harmonically related bands, protection criteria and sharing considerations relating to deep space research, and preferred frequencies and bandwidths for deep space research are considered.

Degroot, N. F.↗

NASA NTRS1984

The COSPAS-SARSAT system

The SARSAT/COSPAS satellite network uses 121.5 and 406 MHz buoys to locale ships and aircraft in distress. The 121.5 MHz system, obligatory on many aircraft, gives localization to within 10 km, and, despite being subject to considerable radio interference and a poor signal to noise ratio, is responsible for saving 200 lives. The 406 MHz location error is 2 km in 75% of cases, and 2 hr for 95% of cases in the worst conditions. It suffers however from interference from illegal broadcasts in the frequency band.

Werstiuk, H. L.↗

NASA NTRS2005

Mitigation of Laser Beam Scintillation in Free-Space Optical Communication Systems Through Coherence-Reducing Optical Materials

Free-space optical communication systems (also known as lasercom systems) offer several performance advantages over traditional radio frequency communication systems. These advantages include increased data rates and reduced operating power and system weight. One serious limiting factor in a lasercom system is Optical turbulence in Earth's atmosphere. This turbulence breaks up the laser beam used to transmit the information into multiple segments that interfere with each other when the beam is focused onto the receiver. This interference pattern at the receiver changes with time causing fluctuations in the received optical intensity (scintillation). Scintillation leads to intermittent losses of the signal and an overall reduction in the lasercom system's performance. Since scintillation is a coherent effect, reducing the spatial and temporal coherence of the laser beam will reduce the scintillation. Transmitting a laser beam through certain materials is thought to reduce its coherence. Materials that were tested included: sapphire, BK7 glass, fused silica and others. The spatial and temporal coherence of the laser beam was determined by examining the interference patterns (fringes) it formed when interacting with various interferometers and etalons.

Renner, Christoffer J.↗

NASA NTRS1989

Acquisition signal transmitter

An encoded information transmitter which transmits a radio frequency carrier that is amplitude modulated by a constant frequency waveform and thereafter amplitude modulated by a predetermined encoded waveform, the constant frequency waveform modulated carrier constituting an acquisition signal and the encoded waveform modulated carrier constituting an information bearing signal, the acquisition signal providing enhanced signal acquisition and interference rejection favoring the information bearing signal. One specific application for this transmitter is as a distress transmitter where a conventional, legislated audio tone modulated signal is transmitted followed first by the acquisition signal and then the information bearing signal, the information bearing signal being encoded with, among other things, vehicle identification data. The acquistion signal enables a receiver to acquire the information bearing signal where the received signal is low and/or where the received signal has a low signal-to-noise ratio in an environment where there are multiple signals in the same frequency band as the information bearing signal.

Friedman, Morton L.↗

NASA NTRS2006

Receiver Would Control Phasing of a Phased-Array Antenna

In a proposed digital signal-processing technique, a radio receiver would control the phasing of a phased-array antenna to aim the peaks of the antenna radiation pattern toward desired signal sources while aiming the nulls of the pattern toward interfering signal sources. The technique was conceived for use in a Global Positioning System (GPS) receiver, for which the desired signal sources would be GPS satellites and typical interference sources would be terrestrial objects that cause multipath propagation. The technique could also be used to optimize reception in spread-spectrum cellular-telephone and military communication systems. During reception of radio signals in a conventional phased-array antenna system, received signals at their original carrier frequencies are phase-shifted, then combined by analog circuitry. The combination signal is then subjected to down-conversion and demodulation. In a system according to the proposed technique (see figure), the signal received by each antenna would be subjected to down-conversion, spread-spectrum demodulation, and correlation; this processing would be performed separately from, and simultaneously with, similar processing of signals received by the other antenna elements. Following analog down-conversion to baseband, the signals would be digitized, and all subsequent processing would be digital. In the digital process, residual carriers would be removed and each signal would be correlated with a locally generated model pseudorandum-noise code, all following normal GPS procedure. As part of this procedure, accumulated values would be added in software and the resulting signals would be phase-shifted in software by the amounts necessary to synthesize the desired antenna directional gain pattern of peaks and nulls. The principal advantage of this technique over the conventional radio-frequency-combining technique is that the parallel digital baseband processing of the signals from the various antenna elements would be a relatively inexpensive and flexible means for exploiting the inherent multiple-peak/multiple-null aiming capability of a phased-array antenna. In the original intended GPS application, the peaks and nulls could be directed independently for each GPS signal being tracked by the GPS receiver. The technique could also be applied to other code-division multiple-access communication systems.

Dunn, Charles E.↗

NASA NTRS2007

An Analysis of the Effects of RFID Tags on Narrowband Navigation and Communication Receivers

The simulated effects of the Radio Frequency Identification (RFID) tag emissions on ILS Localizer and ILS Glide Slope functions match the analytical models developed in support of DO-294B provided that the measured peak power levels are adjusted for 1) peak-to-average power ratio, 2) effective duty cycle, and 3) spectrum analyzer measurement bandwidth. When these adjustments are made, simulated and theoretical results are in extraordinarily good agreement. The relationships hold over a large range of potential interference-to-desired signal power ratios, provided that the adjusted interference power is significantly higher than the sum of the receiver noise floor and the noise-like contributions of all other interference sources. When the duty-factor adjusted power spectral densities are applied in the evaluation process described in Section 6 of DO-294B, most narrowband guidance and communications radios performance parameters are unaffected by moderate levels of RFID interference. Specific conclusions and recommendations are provided.

LaBerge, E. F. Charles↗

DOE OSTI2024

Development of a strip-shaped X-ray mapping system for 9-cell superconducting cavities

Electrons emitted via field emission during superconducting (SC) radio-frequency (RF) cavity tests at vertical test stands often collide with the iris region inside the cavity, generating X-rays at these locations. In 1.3 GHz 9-cell SC RF cavities designed for the International Linear Collider (ILC), stiffener rings located outside the iris region between cells can interfere with X-ray detection, complicating the precise identification of field emission sites. Hence, in this study, we developed a high-density strip X-ray mapping systems (sX-map) that can be inserted into the iris region of ILC-type 9-cell SC RF cavities. This sX-map facilitates efficient and accurate detection of X-rays generated near the irises, unaffected by the presence of stiffener rings. The sX-map consisted of 32 sensors per strip, with sensors spaced approximately 10 mm apart. It was deployed in every iris of the 9-cell cavity, using a total of 320 sensors. A multiplexer was employed to facilitate the readout of a large number of detectors using a minimal number of signal lines, connecting the strips inside within the vertical test cryostat. In a vertical test conducted at Jefferson Lab (JLab), we demonstrated the capability of sX-map to detect X-rays despite the presence of a stiffener ring. This paper presents the detailed design of the sX-map and the results from the vertical test at JLab.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

NASA NTRS1973

An adaptive array for interference rejection.

An experimental adaptive array based on the feedback concept discussed by Widrow et al. (1967) is considered. The processing procedure described makes it possible to discriminate between 'desired' and 'undesired' signals by means of a reference signal. The application of this approach to the problem of interference rejection in radio communications is investigated. The reference signal in this case can only approximate the desired signal. A description is given of a number of experiments in which the desired signal is a modulated signal and the reference signal is a CW signal at the desired signal carrier frequency.

Riegler, R. L.↗

NASA NTRS1984

COSPAS/SARSAT: An overview

The SARSAT/COSPAS satellite network uses 121.5 and 406 MHz buoys to locate ships and aircraft in distress. The 121.5 MHz system, obligatory on many aircraft, gives localization to within 10 km, and, despite being subject to considerable radio interference and a poor signal to noise ratio, is responsible for saving nearly 200 lives. The 406 MHz location error is 2 km in 75% of cases, and less than or equal to 2 hr for 95% of cases in the worst conditions. It suffers however from interference from illegal broadcasts in the frequency band.

Mcgunigal, T. E.↗

NASA NTRS2009

Aligning a Receiving Antenna Array to Reduce Interference

A digital signal-processing algorithm has been devised as a means of aligning (as defined below) the outputs of multiple receiving radio antennas in a large array for the purpose of receiving a desired weak signal transmitted by a single distant source in the presence of an interfering signal that (1) originates at another source lying within the antenna beam and (2) occupies a frequency band significantly wider than that of the desired signal. In the original intended application of the algorithm, the desired weak signal is a spacecraft telemetry signal, the antennas are spacecraft-tracking antennas in NASA s Deep Space Network, and the source of the wide-band interfering signal is typically a radio galaxy or a planet that lies along or near the line of sight to the spacecraft. The algorithm could also afford the ability to discriminate between desired narrow-band and nearby undesired wide-band sources in related applications that include satellite and terrestrial radio communications and radio astronomy. The development of the present algorithm involved modification of a prior algorithm called SUMPLE and a predecessor called SIMPLE. SUMPLE was described in Algorithm for Aligning an Array of Receiving Radio Antennas (NPO-40574), NASA Tech Briefs Vol. 30, No. 4 (April 2006), page 54. To recapitulate: As used here, aligning signifies adjusting the delays and phases of the outputs from the various antennas so that their relatively weak replicas of the desired signal can be added coherently to increase the signal-to-noise ratio (SNR) for improved reception, as though one had a single larger antenna. Prior to the development of SUMPLE, it was common practice to effect alignment by means of a process that involves correlation of signals in pairs. SIMPLE is an example of an algorithm that effects such a process. SUMPLE also involves correlations, but the correlations are not performed in pairs. Instead, in a partly iterative process, each signal is appropriately weighted and then correlated with a composite signal equal to the sum of the other signals.

Jongeling, Andre P.↗

NASA NTRS2007

Electro-Optical Modulator Bias Control Using Bipolar Pulses

An improved method has been devised for controlling the DC bias applied to an electro-optical crystal that is part of a Mach-Zehnder modulator that generates low-duty-cycle optical pulses for a pulse-position modulation (PPM) optical data-communication system. In such a system, it is desirable to minimize the transmission of light during the intervals between pulses, and for this purpose, it is necessary to maximize the extinction ratio of the modulator (the ratio between the power transmitted during an "on" period and the power transmitted during an "off" period). The present method is related to prior dither error feedback methods, but unlike in those methods, there is no need for an auxiliary modulation subsystem to generate a dithering signal. Instead, as described below, dither is effected through alternation of the polarity of the modulation signal. The upper part of Figure 1 schematically depicts a Mach-Zehnder modulator. The signal applied to the electro-optical crystal consists of a radio-frequency modulating pulse signal, VRF, superimposed on a DC bias Vbias. Maximum extinction occurs during the off (VRF = 0) period if Vbias is set at a value that makes the two optical paths differ by an odd integer multiple of a half wavelength so that the beams traveling along the two paths interfere destructively at the output beam splitter. Assuming that the modulating pulse signal VRF has a rectangular waveform, maximum transmission occurs during the "on" period if the amplitude of VRF is set to a value, V , that shifts the length of the affected optical path by a half wavelength so that now the two beams interfere constructively at the output beam splitter. The modulating pulse signal is AC-coupled from an amplifier to the electro-optical crystal. Sometimes, two successive pulses occur so close in time that the operating point of the amplifier drifts, one result being that there is not enough time for the signal level to return to ground between pulses. Also, the difference between the optical-path lengths can drift with changes in temperature and other spurious effects. The effects of both types of drift are suppressed in the present method, in which one takes advantage of the fact that when Vbias is set at the value for maximum extinction, equal-magnitude positive and negative pulses applied to the electro-optical crystal produce equal output light pulses.

Farr, William↗

NASA NTRS2012

Connect Global Positioning System RF Module

The CoNNeCT Global Positioning System RF Module (GPSM) slice is part of the JPL CoNNeCT Software Defined Radio (SDR). CoNNeCT is the Communications, Navigation, and Net working reconfigurable Testbed project that is part of NASA's Space Communication and Nav igation (SCaN) Program. The CoNNeCT project is an experimental dem onstration that will lead to the advancement of SDRs and provide a path for new space communication and navigation systems for future NASA exploration missions. The JPL CoNNeCT SDR will be flying on the International Space Station (ISS) in 2012 in support of the SCaN CoNNeCT program. The GPSM is a radio-frequency sampler module (see Figure 1) that directly sub-harmonically samples the filtered GPS L-band signals at L1 (1575.42 MHz), L2 (1227.6 MHz), and L5 (1176.45 MHz). The JPL SDR receives GPS signals through a Dorne & Margolin antenna mounted onto a choke ring. The GPS signal is filtered against interference, amplified, split, and fed into three channels: L1, L2, and L5. In each of the L-band channels, there is a chain of bandpass filters and amplifiers, and the signal is fed through each of these channels to where the GPSM performs a one-bit analog-to-digital conversion (see Figure 2). The GPSM uses a sub-harmonic, single-bit L1, L2, and L5 sampler that samples at a clock rate of 38.656 MHz. The new capability is the down-conversion and sampling of the L5 signal when previous hardware did not provide this capability. The first GPS IIF Satellite was launched in 2010, providing the new L5 signal. With the JPL SDR flying on the ISS, it will be possible to demonstrate navigation solutions with 10-meter 3-D accuracy at 10-second intervals using a field-program mable gate array (FPGA)-based feedback loop running at 50 Hz. The GPS data bits will be decoded and used in the SDR. The GPSM will also allow other waveforms that are installed in the SDR to demonstrate various GNSS tracking techniques.

Franklin, Garth W.↗

NASA NTRS1993

Performance Of The Split-Symbol Moments Estimator

Report presents analysis of performance of Split-Symbol Moments Estimator (SSME) algorithm. Designed to estimate symbol signal-to-noise ratio of radio signal modulated by binary data pulses of period T and received in presence of additive white Gaussian noise. Incoming signal and noise first filtered, then sampled Ns - T/Ts times per symbol period. This study focuses on performance of SSME in case in which frequency width limited by digital filter and inter-symbol interference is thereby generated.

Shah, Biren N.↗