Search NASA⌕ Search

SEARCH · Search NASA

Results for “STEELS - HALCOMB”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Superior strength-ductility synergy by hetero-structuring high manganese steel

Lacking of forest hardening makes low ductility in steels long challenge particularly at high yield strength. Here, we report to make good use of hetero-structuring for superior strength-ductility synergy in high manganese steel. The point is to retain original deformed structure of large quantity, along with recrystallized ultrafine-grains and fine grains, jointly for most effective heterogeneous deformation-induced (HDI) hardening especially at high strength. The residual plastic strain of larger than 0.2% and large proportion of HDI stress over 60% indicate the crucial role in ductility by HDI hardening. This renders a significantly upgraded strength-ductility combination within high strength scope.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A Model to Account for the Effects of Load Ratio and Hydrogen Pressure on the Fatigue Crack Growth Behavior of Pressure Vessel Steels

A phenomenological model for estimating the effects of load ratio R and hydrogen pressure P H2 on the hydrogen-assisted fatigue crack growth rate (HA–FCGR) behavior in the transient and steady-state regimes of pressure vessel steels is described. The “transient regime” is identified with crack growth within a severely embrittled zone of intense plasticity at the crack tip. The “steady-state” behavior is associated with the crack growing into a region of comparatively lower hydrogen concentration located further away from the crack tip. The model treats the effects of R and P H2 as being functionally separable. In the transient regime, the effects of the hydrogen pressure on the HA–FCGR behavior were negligible but were significant in the steady-state regime. The hydrogen concentration in the steady-state region is modeled as being dependent on the kinetics of lattice diffusion, which is sensitive to pressure. Experimental HA–FCGR data from the literature were used to validate the model. The new model was shown to be valid over a wide range of conditions that ranged between –1 ≤ R ≤ 0.8 and 0.02 ≤ P H2 ≤ 103 MPa for pressure vessel steels.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Process-driven roadmap for depositing super duplex stainless steel via wire Arc additive manufacturing

Here, this study systematically investigates the effects of shielding gas, bead spacing, weld mode, and travel speed on the phase balance, porosity, and hardness of wire arc additively manufactured (WAAM) super duplex stainless steel (ER2594). Robotic WAAM was employed to fabricate multilayer walls under systematically varied process conditions, followed by phase transformation simulations, X-ray computed tomography (XCT), electron backscatter diffraction (EBSD), and microhardness evaluation. Thermodynamic simulations predicted rapid cooling of AM process can suppress the potential formation of deleterious precipitates which was later validated via cross-sectional microstructure analyses of printed samples. XCT revealed porosity levels below 0.2% for all deposits, with reduced travel speed significantly lowering defect volume. Microstructural analyses revealed the evolution of various austenite precipitates, including grain boundary austenite (GBA), Widmanstätten austenite (WA), and intergranular austenite (IGA), sequentially upon cooling of the ferrite phase. Among all process parameters, weld transfer mode exhibited the strongest influence on phase balance; pulsed mode promoted higher ferrite retention (~ 36%) compared to RapidX mode. No consistent relationship between stabilized phase fraction and captured microhardness was observed. This work provides critical insights for optimizing WAAM parameters to control phase balance and mechanical performance, which is essential for producing high-integrity super duplex stainless-steel components for nuclear and marine applications.

Grain orientation↗
DOE OSTI2021

Thermodynamics and kinetics of precipitation and austenite reversion during aging of Ti-free grade 300 maraging steel manufactured by laser powder bed fusion (LPBF)

Austenite reversion and intermetallic precipitation are two key phase transformations in maraging steels which determine the strength and ductility. Usually, an optimum aging temperature/time is determined using trial and error approach with inputs from thermodynamic databases and a-posteriori microscopy/hardness evaluations. In this study, a thermo-kinetic model is developed to predict the precipitation and austenite reversion kinetics during various post-fabrication heat treatments in a Ti-free variant of grade 300 maraging steel manufactured using laser powder bed fusion. The thermo-kinetic model was based on the principles of Scheil solidification and the classical nucleation theory. The predictions from the thermo-kinetic model were verified using suitable microscopy techniques, and the results from the thermo-kinetic model agree well with the experimental measurements. Overall, results highlight the fact that an Integrated Computational Materials Engineering approach can be used to predict the precipitation and austenite reversion kinetics, and be used as an input for an efficient design of heat treatments for achieving optimum mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Methods to Observe Tribological Failures in Self-Mated Steel Contacts

Scuffing, a type of wear found in highly stressed or poorly lubricated contacts, is characterized by a rapid increase in friction and severe plastic deformation of the near-surface material. Scuffing has proven difficult to study because it initiates unpredictably, progresses rapidly, and typically develops within an inaccessible contact interface. Although there have been successful in-situ studies of scuffing in real-time, the transparent counter body needed for these studies changes the interactions between the surfaces and the lubricant, which affects the scuffing process in unknown ways. This paper describes the development of X-ray-compatible tribometry to study the scuffing of self-mated steels in-situ and in real-time. The method uses a crossed cylinders configuration with a thin (500 μm thick) stationary component and a small (≈200 μm) contact width to maximize X-ray interactions with atoms within the stress field generated by the contact. The resulting instrument and method are used to benchmark the scuffing response of self-mated 52,100 steel under tribologically challenging ‘oil-off’ lubrication conditions. The results demonstrate reliable scuffing in this configuration despite the relatively small contact areas and loads used. Following scuffing, gross plastic deformation was observed on both surfaces along with significant subsurface grain refinement and flow only on the stationary surface, which experienced constant contact. Interestingly, high friction initiated at specific locations of the migratory surface, which experienced intermittent contact, and then propagated across the track over time, suggesting that local conditions of the migratory surface dominated friction leading into the failure event.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Automated Grain Boundary (GB) Segmentation and Microstructural Analysis in 347H Stainless Steel Using Deep Learning and Multimodal Microscopy

Austenitic 347H stainless steel offers superior mechanical properties and corrosion resistance required for extreme operating conditions such as high temperature. The change in microstructure due to composition and process variations is expected to impact material properties. Identifying microstructural features such as grain boundaries thus becomes an important task in the process-microstructure-properties loop. Applying convolutional neural network (CNN)-based deep learning models is a powerful technique to detect features from material micrographs in an automated manner. In contrast to microstructural classification, supervised CNN models for segmentation tasks require pixel-wise annotation labels. However, manual labeling of the images for the segmentation task poses a major bottleneck for generating training data and labels in a reliable and reproducible way within a reasonable timeframe. Microstructural characterization especially needs to be expedited for faster material discovery by changing alloy compositions. Here, in this study, we attempt to overcome such limitations by utilizing multimodal microscopy to generate labels directly instead of manual labeling. We combine scanning electron microscopy images of 347H stainless steel as training data and electron backscatter diffraction micrographs as pixel-wise labels for grain boundary detection as a semantic segmentation task. The viability of our method is evaluated by considering a set of deep CNN architectures. We demonstrate that despite producing instrumentation drift during data collection between two modes of microscopy, this method performs comparably to similar segmentation tasks that used manual labeling. Additionally, we find that naïve pixel-wise segmentation results in small gaps and missing boundaries in the predicted grain boundary map. By incorporating topological information during model training, the connectivity of the grain boundary network and segmentation performance is improved. Finally, our approach is validated by accurate computation on downstream tasks of predicting the underlying grain morphology distributions which are the ultimate quantities of interest for microstructural characterization.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Stress relaxation cracking susceptibility evaluation in 347H stainless steel welds

Abstract Stress relaxation cracking (SRC) has been reported as a dominant failure mechanism for 347H stainless steel welds at elevated service temperatures, occurring in either the heat-affected zone (HAZ) or fusion zone (FZ). In this study, SRC susceptibility of physically simulated HAZ and cross-welded E347-347H stainless steel welds was studied using a four-step accelerated SRC test with a thermomechanical physical simulator. The stress and temperature range studied represents weld-induced residual stress at 150–600 MPa and post-weld heat treatment temperatures between 800 and 1050 °C. For all temperature conditions, the cross-welded samples failed at a lower critical stress threshold than the simulated HAZ. A finite element model of a 50.8-mm-thick single-V groove weld was used to generate the residual stress maps induced by a 40-pass welding procedure, which in combination with the experimental threshold stress map predicted potential SRC failure locations. Postmortem microstructural evaluations were performed to identify contributing characteristics to SRC. It was found that HAZ samples exhibited a combination of creep void development, secondary cracks with intergranular fracture near grain boundary carbides, and eutectic phases. FZ samples showed brittle fracture with cracks propagating along straight, non-tortuous interdendritic grain boundaries.

42 ENGINEERING↗
DOE OSTI2020

Effects of heat treatment and build orientation on the evolution of $ϵ$ and $α'$ martensite and strength during compressive loading of additively manufactured 304L stainless steel

In this paper, the effect of heat-treatment and build orientation on martensitic phase transformation in additively manufactured (AM) 304L stainless steel is studied and compared with conventionally produced wrought material. The relationships between observed martensitic transformations and material microstructures and their effects on mechanical strength are established through experimental observations. In situ high-energy X-ray powder diffraction measurements were performed to monitor the evolution of $ϵ$ and $α'$ martensite during compressive loading of stainless steel. Electron backscatter diffraction (EBSD) was used to provide insight on initial grain morphology, crystallographic misorientation within grains, and crystallographic texture. Heat treatment alters the microstructure of AM samples creating different initial conditions. This difference in starting microstructure resulted in variability in martensitic transformation during compressive deformation. The rate of martensitic transformation decreased for AM samples treated with temperatures up to 1100°C, after which the AM microstructures recrystallized, resulting in increased rate of martensitic transformation for those samples treated at higher temperatures. It was also observed that aligning the axis of compression with the AM build direction resulted in a lower rate of strain-induced martensite formation as opposed to aligning the compression axis perpendicular to it. More favorable distribution of crystal orientations in the latter loading orientation promoted martensitic transformation. These and additional experimental observations from EBSD in terms of kernel average misorientation, mean grain orientation spread, and mean crystallite size reveal strong microstructural effects on strength of additively manufactured metallic materials.

304L stainless steel↗
DOE OSTI2020

He ion irradiation response of a gradient T91 steel

Metallic materials with a gradient microstructure usually exhibit excellent mechanical properties. How- ever, the radiation response of gradient structural materials is less well understood. In this work, room- temperature He ion irradiation up to ~4.5 dpa with ~10 at% He injection was performed on a gradient T91 steel processed by surface severe plastic deformation. In comparison to the coarse-grained ferritic T91, the gradient T91 with the nanocrystalline layers shows improved radiation tolerance in terms of less bubble swelling and radiation hardening. Additionally, bubble distribution along grain boundaries depends on misorientation angle suggesting a strong capacity of non-equilibrium grain boundaries in storing He atoms. The present study provides insight into the design of radiation tolerant gradient steels for nuclear industry applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic properties of 316l stainless steel repaired using electron beam additive manufacturing

Additive manufacturing has the potential to be used for repair of high-value parts, but the strength and integrity of such repaired parts, especially under dynamic loading, in still unknown. This work presents the results of high strain-rate dynamic testing of additively repaired stainless steel samples. The 316L samples were intentionally damaged and subsequently repaired with 308L stainless steel wire using electron beam additive manufacturing. The repaired samples were subjected to gas-gun impact testing to induce incipient damage and determine the role played by the repaired region in dictating damage and failure. The results show the following: 1) the equation of state of the repaired region is comparable to the original material as shown by the unchanged spall plane location, 2) the deformation behavior is similar to the original material as shown by the similar Hugoniot Elastic limit, 3) the spall strength of the repaired region is slightly higher than the original material due to varying grain size, and 4) the damage morphology in the repaired region is different and involves a high rate of void coalescence. In conclusion, despite these minor differences in the spall strength and the damage morphology, the overall dynamic response of the original material and repaired samples is similar suggesting that AM is a promising approach for repairing high-value components.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Novel effects of grain size and ion implantation on grain boundary segregation in ion irradiated austenitic steel

Nuclear reactor environments are extreme in nature due to the combination of exposure to corrosive coolant, mechanical stresses, and neutron irradiation damage. This combination of environments can lead to irradiation induced/assisted precipitation, segregation, and embrittlement coupled with enhanced creep and stress corrosion cracking. While nanostructured materials are of interest in a variety of applications due to their unique properties including high mechanical strength, for nuclear applications nanostructured materials have the added benefit of irradiation resistance due to the high volume density of sinks for irradiation-induced defects. In this study, we show unique radiation-induced segregation (RIS) behavior in nanocrystalline 304 stainless steel (SS304). Typical RIS in austenitic steels includes Ni enrichment and Cr depletion within the grain boundaries. In nanostructured SS304 this RIS is reduced. Furthermore, interestingly, some grain boundaries in the nanocrystalline SS304 in this study were found to be enriched in Cr after Fe 2+ ion irradiation at 500 °C up to 50 displacements per atom (dpa). To understand this unique observation, lattice-based atomic kinetic Monte Carlo simulations were performed to investigate the effects of grain size, thermal segregation, as well as injected interstitials (introduced as Fe self-ions). The results indicate that the Cr enrichment at grain boundaries may be caused by combined effects of grain size, self-ion injection and preferential Cr diffusion via the interstitial mechanism. In conclusion, the findings also suggest a possible difference in RIS between ion and neutron irradiations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

First-principles and cluster expansion study of the effect of magnetism on short-range order in Fe–Ni–Cr austenitic stainless steels

Short-range order (SRO), the regular and predictable arrangement of atoms over short distances, alters the mechanical properties of technologically relevant structural materials such as medium/high entropy alloys and austenitic stainless steels. In this study, we present a generalized spin cluster expansion (CE) model and show that magnetism is a primary factor influencing the level of SRO present in austenitic Fe-Ni-Cr alloys. The spin CE consists of a chemical cluster expansion combined with an Ising model for Fe-Ni-Cr austenitic alloys. It explicitly accounts for local magnetic exchange interactions, thereby capturing the effects of finite temperature magnetism on SRO. Model parameters are obtained by fitting to a first-principles data set comprising both chemically and magnetically diverse FCC configurations. The magnitude of the magnetic exchange interactions are found to be comparable to the chemical interactions. Compared to a conventional implicit magnetism CE built from only magnetic ground state configurations, the spin CE shows improved performance on several experimental benchmarks over a broad spectrum of compositions, particularly at higher temperatures due to the explicit treatment of magnetic disorder. We find that SRO is strongly influenced by alloy Cr content, since Cr atoms prefer to align antiferromagnetically with nearest neighbors but become magnetically frustrated with increasing Cr concentration. Using the spin CE, we predict that increasing the Cr concentration in typical austenitic stainless steels promotes the formation of SRO and increases order-disorder transition temperatures. Furthermore, this study underscores the significance of considering magnetic interactions explicitly when exploring the thermodynamic properties of complex transition metal alloys. It also highlights guidelines for customizing SRO through adjustments of alloy composition.

36 MATERIALS SCIENCE↗
DOE OSTI2025

MX precipitate behavior in an irradiated advanced Fe-9Cr steel: Self-ion irradiation effects on phase stability

In an effort to optimize Fe-9Cr reduced activation ferritic/martensitic (RAFM) steels and to inform the design and operation of fusion reactors, this work represents the first in a series of cohesive studies dedicated to the evolution of MX-TiC precipitates under accelerated single and dual ion irradiations. This study investigates CNA9, a simplified Fe-9Cr RAFM steel featuring initial MX-TiC precipitate densities of (2.3±0.3)×10²¹ m⁻³. This material was subjected to single self-ion irradiation at damage levels ranging from 1 to 100 displacements per atom (dpa) over a temperature range of 300 to 600°C, with a nominal dose rate of 7×10⁻⁴ dpa/s. Irradiation-induced coarsening was observed, as evidenced by statistically significant increases in mean diameter sizes, at 15 dpa at both 500°C and 600°C, whereas no coarsening was noted at 300°C or 400°C. Further, complete dissolution of precipitates occurred at damage levels of 50 and 100 dpa across the two temperatures tested (300°C and 500°C) while no significant changes were observed at any doses below 15 dpa at 500°C. Experimentally parameterized recoil resolution modeling suggests that the observed radiation stability of MX-TiC precipitates is intricately linked to diffusional changes of solutes resulting from the co-evolution of microstructural features within the experiments. The findings align with current theoretical perspectives on radiation-induced precipitate stability in complex alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Long-term thermal aging behavior and strength reduction in a laser powder bed fusion 316H stainless steel

The long-term thermal stability of structural alloys is essential for ensuring the safe and reliable operation of nuclear reactors and other power plants. While extensive research has explored the effects of thermal aging on conventional stainless steels, the behavior of additively manufactured (AM) alloys remains less understood. This study examines the thermal aging response of laser powder bed fusion (LPBF) 316H stainless steel (SS) at temperatures ranging from 550 °C to 750 °C over durations of up to 10,000 h (approximately 1.14 years). Advanced characterization techniques, including electron microscopy and synchrotron X-ray diffraction, were used to investigate dislocation recovery and phase evolution. Based on these findings, a time-temperature-precipitation (TTP) diagram was developed for LPBF 316H SS, revealing a 10- to100-fold acceleration in precipitation kinetics compared to wrought 316H SS. A physics-informed model was calibrated using the short-term experimental data, enabling predictions of average precipitate sizes, volume fractions of M 23 C 6 and Laves phases, and changes in molybdenum solute concentration for aging up to 1 × 10⁶ h (114 years). These microstructural insights were further utilized to estimate yield strength and extrapolate strength reduction factors over the extended aging period. Despite the accelerated aging kinetics, LPBF 316H SS demonstrated superior yield strength retention compared to its wrought counterpart. In conclusion, this study establishes a framework for evaluating long-term performance using short-term experimental data and supports the accelerated qualification of AM materials for high-temperature structural applications.

Laser powder bed fusion↗
DOE OSTI2025

Effect of stress on Laves phase precipitation in creep ruptured Grade 92 ferritic martensitic steel characterized by a novel accessible method

At high temperature conditions relevant to fossil and nuclear energy plants, Laves phase (Fe 2 X, X=Mo, W) precipitation is observed in common ferritic martensitic (FM) structural steels, with various reported effects on creep behavior. Despite being valuable metrics to correlate with mechanical properties and other precipitate phases, the volume fraction and number density of Laves phase precipitates has been difficult to quantify accurately using common techniques such as transmission electron microscopy (TEM) due to the relatively large size (∼0.25 μm) and low number density (∼10 11 cm −3 ) of Laves precipitates. Here, to address this characterization challenge, we developed and demonstrated a high-throughput and widely accessible method to quantify the volume fraction and number density of the Laves phase based on scanning electron microscope (SEM) images with a backscattered electron signal and the information depth (ID) of backscattered electrons. We applied this new technique in creep ruptured Grade 92 FM steel to study the effect of Laves phase on creep properties and determine the influence of stress on Laves phase precipitation. The quantitative accuracy of the SEM-based volume fraction and number density values was verified using synchrotron high energy X-ray diffraction and serial sectioning tomography. Stress did not significantly affect the Laves phase size or volume fraction during creep testing at 550 – 650°C and stress levels of 90 – 260 MPa (vs. unstressed conditions). Conversely, a moderate but statistically significant stress-enhanced increase in Laves phase number density, corresponding to an increase in nucleation rate, occurred during creep exposure above 110 MPa.

Creep↗
DOE OSTI2019

Selective laser melting of 304L stainless steel: Role of volumetric energy density on the microstructure, texture and mechanical properties

The role of volumetric energy density on the microstructural evolution, texture and mechanical properties of 304L stainless steel parts additively manufactured via selective laser melting process is investigated. 304L is chosen because it is a potential candidate to be used as a matrix in a metal matrix composite with nanoparticles dispersion for energy and high temperature applications. The highest relative density of 99 %±0.5 was achieved using a volumetric energy density of 1400 J/mm 3 . Both XRD analysis and Scheil simulation revealed the presence of a small trace of the delta ferrite phase, due to rapid solidification within the austenitic matrix of 304L. Here, a fine cellular substructure ranged between 0.4–1.8 μm, was detected across different energy density values. At the highest energy density value, a strong texture in the direction of [100] was identified. At lower energy density values, multicomponent texture was found due to high nucleation rate and the existing defects. Yield strength, ultimate tensile strength, and microhardness of samples with a relative density of 99 % were measured to be 540 ± 15 MPa, 660 ± 20 MPa and 254 ± 7 HV, respectively and higher than mechanical properties of conventionally manufactured 304L stainless steel. Heat treatment of the laser melted 304L at 1200 °C for 2 h, resulted in the nucleation of recrystallized equiaxed grains followed by a decrease in microhardness value from 233 ± 3 HV to 208 ± 8 HV due to disappearance of cellular substructure.

304L stainless steel↗
DOE OSTI2020

Microstructure evolution during binder jet additive manufacturing of H13 tool steel

H13 is one of the most used tool steels for both hot and cold work tooling applications. Binder jet additive manufacturing offers the potential to deposit complex tools at scale due to larger powder bed sizes and faster deposition rates. However, to date there is no published literature on the sintering of H13 to full densification. Here, we discuss the pressureless sintering of binder jet AM H13 steel to full densification via supersolidus liquid phase sintering (SLPS) while presenting appropriate process windows (1360 °C – 1380 °C) for densification without distortion. The process windows have been rationalized based on thermodynamic calculations of liquid volume fractions with temperature. We show that higher binder saturation results in higher carbon retention and subsequently early liquid formation that can initiate the sintering process at lower temperatures. We report abnormal grain growth during sintering and found that the solidification phase transformations play a critical role on microstructural evolution and must be considered to accurately model the kinetics of SLPS.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Production of mechanically-generated 316L stainless steel feedstock and its performance in directed energy deposition processing as compared to gas-atomized powder

The objective of this work is to study the feasibility of mechanically-generated feedstock for use in directed energy deposition (DED) processing. Mechanically-generated powder was created by machining 316L stainless steel bar stock followed by comminution of the resulting chips through oscillation ball milling. This methodology's production yield and processing time for the specifications of a commercially available DED system are presented along with resulting powder morphology. Performance of the mechanically-generated feedstock was compared to gas-atomized powder and evaluated based on the following figures of merit: flowability, printed part height, printed part density, and chemical compositional stability throughout processing. Mechanically-generated feedstock was created to meet deposition system requirements. Compared with gas-atomized powder, mechanically-generated powder did not flow as well through the powder-delivery system. Parts printed from mechanically-generated feedstock were generally taller than their counterparts from gas-atomized feedstock, but their densities were less predictable. As a result, chemical composition of prints using both feedstocks was within standard nominal compositions for 316L stainless steel.

36 MATERIALS SCIENCE↗