Search NASA⌕ Search

SEARCH · Search NASA

Results for “STEELS - WEAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

MX precipitate behavior in an irradiated advanced Fe-9Cr steel: Self-ion irradiation effects on phase stability

In an effort to optimize Fe-9Cr reduced activation ferritic/martensitic (RAFM) steels and to inform the design and operation of fusion reactors, this work represents the first in a series of cohesive studies dedicated to the evolution of MX-TiC precipitates under accelerated single and dual ion irradiations. This study investigates CNA9, a simplified Fe-9Cr RAFM steel featuring initial MX-TiC precipitate densities of (2.3±0.3)×10²¹ m⁻³. This material was subjected to single self-ion irradiation at damage levels ranging from 1 to 100 displacements per atom (dpa) over a temperature range of 300 to 600°C, with a nominal dose rate of 7×10⁻⁴ dpa/s. Irradiation-induced coarsening was observed, as evidenced by statistically significant increases in mean diameter sizes, at 15 dpa at both 500°C and 600°C, whereas no coarsening was noted at 300°C or 400°C. Further, complete dissolution of precipitates occurred at damage levels of 50 and 100 dpa across the two temperatures tested (300°C and 500°C) while no significant changes were observed at any doses below 15 dpa at 500°C. Experimentally parameterized recoil resolution modeling suggests that the observed radiation stability of MX-TiC precipitates is intricately linked to diffusional changes of solutes resulting from the co-evolution of microstructural features within the experiments. The findings align with current theoretical perspectives on radiation-induced precipitate stability in complex alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Long-term thermal aging behavior and strength reduction in a laser powder bed fusion 316H stainless steel

The long-term thermal stability of structural alloys is essential for ensuring the safe and reliable operation of nuclear reactors and other power plants. While extensive research has explored the effects of thermal aging on conventional stainless steels, the behavior of additively manufactured (AM) alloys remains less understood. This study examines the thermal aging response of laser powder bed fusion (LPBF) 316H stainless steel (SS) at temperatures ranging from 550 °C to 750 °C over durations of up to 10,000 h (approximately 1.14 years). Advanced characterization techniques, including electron microscopy and synchrotron X-ray diffraction, were used to investigate dislocation recovery and phase evolution. Based on these findings, a time-temperature-precipitation (TTP) diagram was developed for LPBF 316H SS, revealing a 10- to100-fold acceleration in precipitation kinetics compared to wrought 316H SS. A physics-informed model was calibrated using the short-term experimental data, enabling predictions of average precipitate sizes, volume fractions of M 23 C 6 and Laves phases, and changes in molybdenum solute concentration for aging up to 1 × 10⁶ h (114 years). These microstructural insights were further utilized to estimate yield strength and extrapolate strength reduction factors over the extended aging period. Despite the accelerated aging kinetics, LPBF 316H SS demonstrated superior yield strength retention compared to its wrought counterpart. In conclusion, this study establishes a framework for evaluating long-term performance using short-term experimental data and supports the accelerated qualification of AM materials for high-temperature structural applications.

Laser powder bed fusion↗
DOE OSTI2025

Effect of stress on Laves phase precipitation in creep ruptured Grade 92 ferritic martensitic steel characterized by a novel accessible method

At high temperature conditions relevant to fossil and nuclear energy plants, Laves phase (Fe 2 X, X=Mo, W) precipitation is observed in common ferritic martensitic (FM) structural steels, with various reported effects on creep behavior. Despite being valuable metrics to correlate with mechanical properties and other precipitate phases, the volume fraction and number density of Laves phase precipitates has been difficult to quantify accurately using common techniques such as transmission electron microscopy (TEM) due to the relatively large size (∼0.25 μm) and low number density (∼10 11 cm −3 ) of Laves precipitates. Here, to address this characterization challenge, we developed and demonstrated a high-throughput and widely accessible method to quantify the volume fraction and number density of the Laves phase based on scanning electron microscope (SEM) images with a backscattered electron signal and the information depth (ID) of backscattered electrons. We applied this new technique in creep ruptured Grade 92 FM steel to study the effect of Laves phase on creep properties and determine the influence of stress on Laves phase precipitation. The quantitative accuracy of the SEM-based volume fraction and number density values was verified using synchrotron high energy X-ray diffraction and serial sectioning tomography. Stress did not significantly affect the Laves phase size or volume fraction during creep testing at 550 – 650°C and stress levels of 90 – 260 MPa (vs. unstressed conditions). Conversely, a moderate but statistically significant stress-enhanced increase in Laves phase number density, corresponding to an increase in nucleation rate, occurred during creep exposure above 110 MPa.

Creep↗
DOE OSTI2019

Selective laser melting of 304L stainless steel: Role of volumetric energy density on the microstructure, texture and mechanical properties

The role of volumetric energy density on the microstructural evolution, texture and mechanical properties of 304L stainless steel parts additively manufactured via selective laser melting process is investigated. 304L is chosen because it is a potential candidate to be used as a matrix in a metal matrix composite with nanoparticles dispersion for energy and high temperature applications. The highest relative density of 99 %±0.5 was achieved using a volumetric energy density of 1400 J/mm 3 . Both XRD analysis and Scheil simulation revealed the presence of a small trace of the delta ferrite phase, due to rapid solidification within the austenitic matrix of 304L. Here, a fine cellular substructure ranged between 0.4–1.8 μm, was detected across different energy density values. At the highest energy density value, a strong texture in the direction of [100] was identified. At lower energy density values, multicomponent texture was found due to high nucleation rate and the existing defects. Yield strength, ultimate tensile strength, and microhardness of samples with a relative density of 99 % were measured to be 540 ± 15 MPa, 660 ± 20 MPa and 254 ± 7 HV, respectively and higher than mechanical properties of conventionally manufactured 304L stainless steel. Heat treatment of the laser melted 304L at 1200 °C for 2 h, resulted in the nucleation of recrystallized equiaxed grains followed by a decrease in microhardness value from 233 ± 3 HV to 208 ± 8 HV due to disappearance of cellular substructure.

304L stainless steel↗
DOE OSTI2020

Microstructure evolution during binder jet additive manufacturing of H13 tool steel

H13 is one of the most used tool steels for both hot and cold work tooling applications. Binder jet additive manufacturing offers the potential to deposit complex tools at scale due to larger powder bed sizes and faster deposition rates. However, to date there is no published literature on the sintering of H13 to full densification. Here, we discuss the pressureless sintering of binder jet AM H13 steel to full densification via supersolidus liquid phase sintering (SLPS) while presenting appropriate process windows (1360 °C – 1380 °C) for densification without distortion. The process windows have been rationalized based on thermodynamic calculations of liquid volume fractions with temperature. We show that higher binder saturation results in higher carbon retention and subsequently early liquid formation that can initiate the sintering process at lower temperatures. We report abnormal grain growth during sintering and found that the solidification phase transformations play a critical role on microstructural evolution and must be considered to accurately model the kinetics of SLPS.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Production of mechanically-generated 316L stainless steel feedstock and its performance in directed energy deposition processing as compared to gas-atomized powder

The objective of this work is to study the feasibility of mechanically-generated feedstock for use in directed energy deposition (DED) processing. Mechanically-generated powder was created by machining 316L stainless steel bar stock followed by comminution of the resulting chips through oscillation ball milling. This methodology's production yield and processing time for the specifications of a commercially available DED system are presented along with resulting powder morphology. Performance of the mechanically-generated feedstock was compared to gas-atomized powder and evaluated based on the following figures of merit: flowability, printed part height, printed part density, and chemical compositional stability throughout processing. Mechanically-generated feedstock was created to meet deposition system requirements. Compared with gas-atomized powder, mechanically-generated powder did not flow as well through the powder-delivery system. Parts printed from mechanically-generated feedstock were generally taller than their counterparts from gas-atomized feedstock, but their densities were less predictable. As a result, chemical composition of prints using both feedstocks was within standard nominal compositions for 316L stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A comparison of surrogate constitutive models for viscoplastic creep simulation of HT-9 steel

Mechanistic microstructure-informed constitutive models for the mechanical response of polycrystals are a cornerstone of computational materials science. However, as these models become increasingly more complex – often involving coupled differential equations describing the effect of specific deformation modes – their associated computational costs can become prohibitive, particularly in optimization or uncertainty quantification tasks that require numerous model evaluations. To address this challenge, surrogate constitutive models that balance accuracy and computational efficiency are highly desirable. Data-driven surrogate models, that learn the constitutive relation directly from data, have emerged as a promising solution. In this work, we develop two local surrogate models for the viscoplastic response of a steel: a piecewise response surface method and a mixture of experts model. These surrogates are designed to adapt to complex material behavior, which may vary with material parameters or operating conditions. The surrogate constitutive models are applied to creep simulations of HT-9 steel, an alloy of considerable interest to the nuclear energy sector due to its high tolerance to radiation damage, using training data generated from viscoplastic self-consistent (VPSC) simulations. In conclusion, we define a set of test metrics to numerically assess the accuracy of our surrogate models for predicting viscoplastic material behavior, and show that the mixture of experts model outperforms the piecewise response surface method in terms of accuracy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electrochemical study of the dissolution of oxide films grown on type 316L stainless steel in molten fluoride salt

The corrosion behavior of oxide films grown on Type 316L stainless steel (SS) in molten FLiNaK (LiF-NaF-KF: 46.5−11.5−42 mol.%) salt was investigated. The results show that the oxide film formed on Type 316L SS is unstable and can only temporarily protect materials from corrosion in molten FLiNaK salt. Based on the electrochemical impedance spectroscopy, the oxide dissolution rate is calculated to be 0.85 nm/h at 700 °C in molten FLiNaK salt. Finally, after the oxide film dissolved, Cr and Fe are selective dealloyed from the steel, leading to intergranular corrosion of Type 316L SS in molten fluoride salt.

EIS↗
DOE OSTI2022

Enhanced crevice corrosion of stainless steel 316 by degradation of Cr-containing hollandite crevice former

This study explores the corrosion interactions between stainless steel 316 (SS316), a candidate nuclear waste canister material, and Cr-containing hollandite (Ba 1.15 Cr 2.3 Ti 5.7 O 16 ), a model ceramic nuclear waste form. The two materials were corroded in close proximity in 0.6 M NaCl solution at 90 °C for 28 days. Severe crevice corrosion was observed on the stainless steel surface after the corrosion experiment, which is likely associated with the rapid accumulation of Cr 3+ cations originating from both SS316 and the Cr-containing hollandite. Furthermore, the enhanced corrosion of SS316 by the corrosion products of hollandite is quantitatively explained using a classical crevice corrosion model.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Reverse martensitic transformation on the corrosion behavior of a 2304 lean duplex stainless steel

This study investigates the influence of the reverse martensitic transformation on the corrosion behavior of 2304 lean duplex stainless steel (LDSS) at low temperatures (400–600°C). The steel underwent cold rolling, followed by isochronal annealing for 0.5 h. Phase transformations and microstructures were analyzed using X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Corrosion resistance was evaluated using a syringe cell with cyclic potentiodynamic polarization in 0.6 M NaCl solution and double-loop electrochemical potentiokinetic reactivation in 0.5 M H 2 SO 4 + 0.001 M KSCN solution. A bimodal breakdown potential behavior, associated with either pitting or transpassivity, was observed in the as-received (AR) and samples annealed at 400°C. Pitting in the AR sample was associated with Al–Mg–Si–Ca–O inclusions, while pitting on the samples annealed at 400°C was linked to local reduced passive film resistance. Severe cold rolling enhanced the pitting resistance of 2304 LDSS. Selective electrochemical etching revealed preferential corrosion at phase interfaces and within the austenite phase. Additionally, annealing at 500°C to 600°C led to a marked decrease in pitting resistance and increased sensitization. Electron backscatter diffraction analysis of the corroded pits in the annealed specimens indicated that pits tend to nucleate and grow in α'-martensite/austenite regions. Furthermore, the nanostructure formed during low-temperature reversion, characterized by dislocation-cell martensite with high dislocation density and stacking faults, may adversely affect corrosion resistance due to heterogeneities associated with alloying element redistribution.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Oxidation of porous stainless steel supports for metal-supported solid oxide electrolysis cells

Oxidation behavior of porous P434L ferritic stainless steel, used for the fabrication of metal-supported solid oxide electrolysis cells (MS-SOEC), is studied under oxygen-side and steam-side conditions. The impact of oxygen content on the oxygen side and steam:hydrogen ratio on the steam side is determined at 700°C for bare, as-sintered samples. For these conditions, oxidation is more aggressive in the steam-side atmosphere. Oxygen with 3% humidification and steam:hydrogen ratio of 90:10 are selected for further assessment with pre-oxidized, catalyst-coated, and CuMn1·8O4-coated samples. The rapid oxidation at 700°C and breakaway oxidation at 600 °C observed for bare stainless steel in 90:10 steam:hydrogen is mitigated by pre-oxidizing the sample in air before exposure. In oxygen, addition of the catalyst or CuMn 1·8 O 4 coatings moderately increases the oxidation rate, due to consumption of Cr via reaction between the coatings and Cr-oxide scale. In conclusion, the results for ex-situ controlled oxidation are similar to oxidation observed after 1000h operation of a full MS-SOEC. In general, the oxidation behavior at 700°C is found to be acceptable.

08 HYDROGEN↗
DOE OSTI2024

Effects of hydrogen partial pressure on crack initiation and growth rate in vintage X52 steel

There is an increasing interest in ensuring compatibility of existing natural gas infrastructure with conveyance of hydrogen, especially for vintage (pre-1970s) pipeline steels. While hydrogen is known to affect the fatigue and fracture resistance of these materials, there is a lack of data on its effects on crack initiation at low hydrogen partial pressure. To address this gap, the current work presents a series of fatigue tests on vintage API Grade X52 steel in pure nitrogen, air and gaseous hydrogen at partial pressures of 1 and 207 bar. Circumferential notch tension (CNT) specimens with direct current potential difference (DCPD) measurements are used to get S–N curves for crack initiation and failure, and compact tension (CT) tests to assess crack growth rates. Results indicate that air accelerates crack initiation, low hydrogen partial pressure affects the crack growth rate, and higher pressures have the largest impact on both. Surprisingly, crack initiation is faster in air than at 1 bar hydrogen partial pressure. The CNT tests also reveal that the orientation of the banded microstructure has no effect on the crack initiation site, but it influences its growth behavior. Moreover, fractography shows that hydrogen also promotes instances of quasi-cleavage and intergranular fracture, linked to embrittlement of the material. Here, these results demonstrate that, while hydrogen may impact the entirety of the fatigue process, its effects on the early stages of damage accumulation become relevant only at larger pressures. More comprehensive studies of crack initiation in hydrogen atmospheres will be critical to future codes and standards for hydrogen infrastructure.

Circumferential notch tension↗
DOE OSTI2023

Predicting the creep-rupture lifetime of a cast austenitic stainless steel using Larson-Miller and Wilshire parametric approaches

An experimental dataset of just over 100 creep tests of a cast austenitic stainless steel, CF8C-Plus, was analyzed by two temperature-compensated parametric models (Larson-Miller, Wilshire et al.) to predict long-term lifetimes as functions of temperature and stress. The dataset and associated regression analyses showed greater scatter than typically found in recent similar studies of wrought Ni-based alloys by the same two models and was attributed to the microstructural inhomogeneity of the cast stainless steel. Qualitatively, the Larson-Miller formalism showed greater lifetime prediction accuracy than the Wilshire approach, with the latter model's predictive ability being particularly degraded by the presence of two very significant outlier results. This observation suggests that the Larson-Miller approach is more robust when treating rupture-time datasets that show particularly wide experimental scatter. Despite the differences in the overall predictive ability, both models yielded similar predictions of the applied stress at which CF8C-Plus would have a creep-limited lifetime of 100,000 h when loaded below the yield point.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Biaxial steel plated concrete constitutive models for composite structures: Implementation and validation

The Steel-plated Concrete (SC) technique is an alternative construction technique with faster onsite construction speed, reduced construction time, and increased structural performance. Aiming to predict the force transfer mechanism of SC elements, an innovative constitutive model package is proposed by implementing experimental-based biaxial steel plate concrete models into the nonlinear finite element (FE) model “Membrane Model of SC (MM-CS).” First, the formulation and implementation of the MM-SC is illustrated in detail, including the equilibrium and compatibility equations and the implementation of constitutive models. Next, various experimental data of SC members are selected and simulated using the proposed MM-SC model. In this research, two types of structures, SC panels and framed SC shear walls, and three types of loading conditions, including uniaxial compression, pure shear, and combined axial-flexural-shear tests, are analyzed respectively. Good agreements were obtained between the reported results and the FE simulation results in terms of yield capacity and ultimate capacity, proving the reliability of the implemented analytical constitutive material models and the biaxial membrane model formulations.

42 ENGINEERING↗
DOE OSTI2022

Leak-tight crack repair for 304L stainless steel using friction surfacing

Here, friction surfacing (FS) was investigated as a method for sealing 50 μm wide thru-cracks in 3-mm-thick 304L stainless steel (304L) plate. Friction surfacing was performed using two sizes of 304L consumable rod, with diameters of 9.52 mm and 12.7 mm, on two substrate conditions (clean and oxidized). Friction surfacing was able to deposit a 600 μm thick coating and repair cracks to a depth of 100 μm - 200 μm below the original surface, when using the 12.7-mm-diameter consumable rod for both substrate conditions. Helium leak rates of 10 -10 atm-cc/s were achieved on crack repairs, designating them as leak-tight by the ANSI N14.5 standard. Optical and scanning electron microscopy were used to investigate the coating microstructure and bond interfaces. In this study, the 12.7-mm-diameter rod performed better with disruption of the oxide layer on the oxidized substrate and providing a more homogenous coating. Mechanical properties of the coated samples were evaluated by performing micro-indentation, tensile, bending, and adhesion testing. Higher hardness in the coatings was observed due to the fine equiaxed grains resulting from dynamic recrystallization. Complete consolidation of plastically deformed material on the substrate and a strong diffusion bond across the interface was observed. This was reflected in tensile and bending properties of the FS coatings being comparable to those of uncoated specimen. No delamination of the FS coating was observed during adhesion testing. The results demonstrate that friction surfacing is a viable option to seal cracks in stainless steels.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of nitriding on mechanical and microstructural properties of Direct Metal Laser Sintered 17-4PH stainless steel

In this work, the effect of the nitriding process on microstructure and mechanical properties of additively manufactured (AM) 17-4PH stainless steel is investigated. The nitriding was performed at 530 °C, 560 °C, and 580 °C for 2 h. The nitriding process improves the hardness and surface roughness of the AM 17-4PH steel. Detailed microstructural characterizations of both as-built and nitride samples are performed using an optical microscope, scanning electron microscope (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction technique. It reveals that the nitride layer thickness increases with nitriding temperature. A distinct transition layer between the substrate and nitride layer is observed in the 560 °C and 580 °C nitride samples. The nitriding process develops almost equiaxed grain microstructure with new secondary phase precipitates, whereas in the as-built material, the grains are primarily columnar along the AM process build direction. Specifically, the nitriding process introduces γ-Fe4N, ε-Fe3N, CrN, and Ni3N precipitates. The increase in Ni- and Cu-rich precipitates with the nitriding temperature explains the observed improvement in the hardness and surface roughness. Furthermore, the nitriding process does not alter the substrate's initial weak crystallographic texture.

17-4PH steel↗
DOE OSTI2020

Characterisation of nano-scale precipitates in BOR60 irradiated T91 steel using atom probe tomography

Atom probe tomography has characterised the microstructural changes in T91 steel after BOR60 reactor irradiation at five temperatures between 376 °C and 524 °C to doses between 14.6 dpa and 35.1 dpa. Irradiation-induced precipitation and segregation to carbide/matrix interface induced by neutron irradiation has been characterised. Atom probe tomography characterisation shows that Mn, Ni, Si -rich (MNS-rich) clusters form in T91 steel irradiated in BOR60 reactor at temperatures between 376 °C and 415 °C, which is not observed at higher temperatures 460 °C and 524 °C. Additionally, the number density, volume fraction and composition of MNS-rich clusters have been characterised. Ni, Mn, Si and P is found to segregate at carbide matrix interface after irradiation at lower temperature and only P segregation is observed at 524 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2021

An Atom Probe Tomography Study of the Through Wall Attenuation Effect on Cu-rich Precipitate Formation in a Reactor Pressure Vessel Steel

In this study, high-Cu weld material harvested from an ex service reactor pressure vessel (RPV) steel from Unit 1 of the decommissioned Zion Nuclear Generating Station has been characterized using atom probe tomography. Samples taken from 4 different positions through the thicknesses of the pressure vessel wall from the water-side to the air-side were characterized, along with an unirradiated baseline material. In the baseline material, no precipitates were found and the Cu was observed to be fully in solid solution; however, scanning transmission electron microscopy combined with energy dispersive spectroscopy (STEM-EDS) revealed the presence of ϵ -Cu that form during processing of the material and results in the concomitant decrease of matrix Cu. Following irradiation, a high number density of nano-scale Cu-rich precipitates (CRPs) were observed, uniformly distributed throughout the matrix. The Cu content within the CRPs was found to be ~30-35 at.% regardless of location in the wall. No statistically significant variation in the compositions, mean radius, number density, or volume fraction as a function of location within the wall was observed. The measured matrix Cu level excluding CRPs contribution was found to be ~90 appm higher than the solubility limit suggesting that further nucleation and growth of the CRPs under continued operations would have occurred. These results clearly demonstrate that the neutron energy attenuation has no significant effect on the precipitation kinetics of CRPs regardless of location in the wall in high-Cu RPV steels under irradiation.

36 MATERIALS SCIENCE↗