SEARCH · Search NASA

Results for “STRESS DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

NASA NTRS1977

A perturbation solution for interlaminar stresses in bidirectional laminates

The paper considers a thin elastic bidirectional symmetric composite laminate subjected to a uniform axial strain. All interlaminar stresses are determined by a zeroth-order perturbation analysis of the governing equations. The method of solution considers the laminate to be composed of an interior region (removed from the free edge) and a boundary layer region. The interior region is analyzed by dropping terms related to powers of the thickness-to-width ratio in the dimensionless elasticity equations. The boundary layer region is studied by introducing a stretching transformation to the governing equations. A uniform solution is then formed by satisfying Prandtl's matching principle of perturbation theory. Results for a four-layer bidirectional graphite-epoxy laminate are compared with existing finite-difference results. It is shown that the perturbation analysis provides more insight into the stress distribution near the free edge.

Hsu, P. W.↗

NASA NTRS1977

Nonlinear panel flutter - A finite-element approach

A finite-element approach has been developed for computing nonlinear flutter characteristics of rectangular isotropic panels with stream-alined side edges, based on aerodynamic forces from supersonic two-dimensional quasi-steady aerodynamic theory. Stress distributions and panel oscillation frequencies were determined from the analysis. The finite-element formulation, solution procedure, and convergence characteristics are presented. Comparisons are made with linear flutter and large-amplitude vibration results and demonstrate that good accuracy is obtained. Non-linear flutter results are presented for effects of aerodynamic damping, length-width ratio, initial in-plane forces and boundary-support conditions. Comparisons with experimental results are also presented.

Mei, C.↗

NASA NTRS1978

Laser-zone growth in a Ribbon-To-Ribbon (RTR) process. Silicon sheet growth development for the large area sheet task of the low-cost solar array project

A new calculation of the effects of thermal stresses during growth on silicon ribbon quality is reported. Thermal stress distributions are computed for ribbon growth under a variety of temperature profiles. A growth rate of 55 cu cm/min with a single ribbon was achieved. The growth of RTR ribbon with a fairly uniform parallel dendritic structure was demonstrated. Results with two approaches were obtained for reducing the Mo impurity level in polycrystalline feedstock. Coating the Mo substrate with Si3N4 does not effect thermal shear separation of the polyribbon; this process shows promise of improving cell efficiency and also increasing the useful life of the molybdenum substrate. A number of solar cells were fabricated on RTR silicon grown from CVD feedstock.

Baghdadi, A.↗

NASA NTRS1979

Analysis of graphite/polyimide rail shear specimens subjected to mechanical and thermal loading

A two-dimensional, linear-elastic, finite element analysis of selected graphite/polyimide rail shear test specimens was made to determine the mechanical loading and the effect of heating the specimen to a uniform temperature. The presence of specimen free edges and their influence on the accuracy of the rail shear test is discussed. Parameters include the length-to-width ratio of the specimen and the ply layup for symmetric, balanced laminates. Results presented include shear and normal stress distributions and the deflection behavior of various specimens caused by the mechanical loading and elevated temperature.

Weisshaar, T. A.↗

NASA NTRS1979

Mode 1 crack surface displacements for a round compact specimen subject to a couple and force

Mode I displacement coefficients along the crack surface are presented for a radially cracked round compact specimen, treated as a plane elastostatic problem, subjected to two types of loading; a uniform tensile stress and a nominal bending stress distribution across the net section. By superposition the resultant displacement coefficient or the corresponding influence coefficient can be obtained for any practical load location. Load line displacements are presented for A/D ratios ranging from 0.40 to 0.95, where A is the crack length measured from the crack mouth to the crack tip and D is the specimen diameter. Through a linear extrapolation procedure crack mouth displacements are also obtained. Experimental evidence shows that the results are valid over the range of A/D ratios analyzed for a practical pin loaded round compact specimen.

Gross, B.↗

NASA NTRS1979

Strength of adhesive-bonded hybrid structures

Structures prepared from materials with different thermal and mechanical properties by means of fiber-strengthened binders can fail in a number of ways. The present lecture is focused on failures through debonding at the metal or at the fiber-reinforced plastic. A method for calculating the stress distribution in adhesive layers as a function of the load is outlined, and its usefulness in providing insight into the behavior of bonds in hybrid structures is noted. Means of eliminating the unfavorable effects of temperature, humidity, creep and relaxation on the bonds in the manufacture of hybrid structures are examined, along with test methods developed for such structures.

Kirschke, L.↗

NASA NTRS1979

Mode I crack surface displacements for a round compact specimen subject to a couple and force

Mode I displacement coefficients along the crack surface are presented for a radially cracked round compact specimen, treated as a plane elastostatic problem, subjected to two types of loading; a uniform tensile stress and a nominal bending stress distribution across the net section. By superposition the resultant displacement coefficient or the corresponding influence coefficient can be obtained for any practical load location. Load line displacements are presented for A/D ratios ranging from 0.40 to 0.95, where A is the crack length measured from the crack mouth to the crack tip and D is the specimen diameter. Through a linear extrapolation procedure crack mouth displacements are also obtained. Experimental evidence shows that the results of this study are valid over the range of A/D ratios analyzed for a practical pin loaded round compact specimen.

Gross, B.↗

NASA NTRS1979

A statistical model of turbulence in two-dimensional mixing layers

A statistical model of turbulence in fully developed two-dimensional incompressible turbulent mixing layers is proposed. The development of this model is largely motivated by the recent experimental observations of Brown and Roshko (1974). The model is based on the proposition that the turbulence of a fully developed two-dimensional incompressible mixing layer is in a state of quasi-equilibrium. The model is used to predict the second-order turbulence statistics of the flow including single-point turbulent Reynolds stress distribution, intensity of turbulent velocity components, rms turbulent pressure fluctuations, power spectra and two-point space-time correlation functions. It is shown that numerical results compare favorably with available experimental measurements.

Tam, C. K. W.↗

NASA NTRS1980

Theory of twisted nonuniformly heated bars

Nonlineary distributed stresses in twisted nonuniformly heated bars of arbitrary cross section are calculated taking into account various elasticity parameters. The approximate theory is shown to be sufficiently general and accurate by comparison with experimental data.

Shorr, B. F.↗

NASA NTRS1981

Finite element analysis of instability-related delamination growth

A parametric study of postbuckled through-width delaminations in laminated coupons was performed. A finite element analysis was developed to analyze the coupons as a combination of linear and geometrically nonlinear components. Because most of the coupon configuration studied behaves linearly, the mixed linear and nonlinear analysis greatly reduced computational costs. The analysis was verified by comparing numerical with exact solutions for simple hypothetical problems. In addition, measured lateral deflections of postbuckled through-width delaminations in laminated coupons were compared with predicted deflections. In the parametric study, stress distributions and strain-energy release rates were calculated for various delamination lengths, delamination depths, applied loads, and lateral deflections. Also, a small number of coupons with through-width delaminations were fatigue tested to obtain delamination growth data. Calculated strain-energy release rates were compared with the observed growth rates to determine the relative importance of the Mode 1 and Mode 2 components of energy release. Growth process was dominated by G sub I.

Whitcomb, J. D.↗

NASA NTRS1981

Mission load dynamic tests of two undensified Space shuttle thermal protection system tiles

Two tests of undensified Space Shuttle thermal protection tiles under combined static and dynamic loads were conducted. The tiles had a density of approximately 144 Kg/cum (LI900 tiles) and were mounted on a strain isolation pad which was 0.41 cm (.160 inch) thick. A combined static and dynamic mission stress histogram representative of the W-3 area of the wing of the orbiter vehicle was applied. The stress histogram was provided by the space shuttle project. Results presented include: tabulation of measured peak and root-mean-square (RMS) accelerations in both compression and tension; peak SIP stress in compression and tension, peak and RMS amplitude response ratios; lateral to vertical response ratios; response time histories; peak stress distributions (histograms), and SIP extension measured both with and without static tension at various mission times.

Leatherwood, J. D.↗

NASA NTRS1981

Dynamic behavior of an unsteady trubulent boundary layer

Experiments on an unsteady turbulent boundary layer are reported in which the upstream portion of the flow is steady (in the mean) and in the downstream region, the boundary layer sees a linearly decreasing free stream velocity. This velocity gradient oscillates in time, at frequencies ranging from zero to approximately the bursting frequency. For the small amplitude, the mean velocity and mean turbulence intensity profiles are unaffected by the oscillations. The amplitude of the periodic velocity component, although as much as 70% greater than that in the free stream for very low frequencies, becomes equal to that in the free stream at higher frequencies. At high frequencies, both the boundary layer thickness and the Reynolds stress distribution across the boundary layer become frozen. The behavior at higher amplitude is quite similar. At sufficiently high frequencies, the boundary layer thickness remains frozen at the mean value over the oscillation cycle, even though flow reverses near the wall during a part of the cycle.

Parikh, P. G.↗

NASA NTRS1980

Three dimensional finite element analysis of layered fiber-reinforced composite materials

A three-dimensional finite element analysis was performed for a biaxially loaded composite laminate (with a centered hole) consisting of several fiber-reinforced composite layers each with a specified fiber orientation. The detailed stress distribution around the hole was determined. Also, the locations of initial damage zones due to different failure mechanisms were indicated.

Lee, J. D.↗

NASA NTRS1981

Measurements of the boundary layer and near wake of a supercritical airfoil at cruise conditions

The flow behavior within the upper-surface boundary layer and near wake of a supercritical airfoil operating at cruise conditions is discussed. Experimental results obtained from wind-tunnel tests are presented which provide a more detailed description of the flow in these regions than was previously available. Mean streamwise velocity profiles measured by pitot-pressure-probe and laser-velocimeter techniques were found to be in excellent agreement. Other mean-flow properties obtained by the laser-velocimeter technique were the local flow angles in the viscous layers and the static pressures at the edges of the boundary layer and wake. The data set also includes measurements of the turbulence intensity and turbulent Reynolds-stress distributions as obtained by the laser-velocimeter technique. To assess the effects of the shock wave, a less extensive set of measurements was realized at a subcritical test condition. The two test conditions (Mach number at free-stream conditions = 0.72, airfoil section lift coefficient = 0.76 and Mach number of free-stream conditions = 0.5, airfoil section lift coefficient = 0.75) provide a good test for state-of-the-art prediction methods because the upper-surface-boundary layer is separated just upstream of the trailing edge in both cases.

Johnson, D. A.↗

NASA NTRS1981

Finite element analysis of instability related delamination growth

Instability-related growth of through-width delaminations in laminated coupons was investigated analytically and experimentally. In the analytical effort, a geometrically nonlinear finite-element stress analysis was used, and the numerical results were compared with exact solutions. In addition, measured lateral deflections of postbuckled through-width delaminations were compared with predicted deflections. Lateral deflections, stress distributions, and strain energy release rates were calculated for various delamination lengths, delamination depths, and applied loads. Delamination growth rates observed for unidirectional graphite/epoxy bonded to aluminum were qualitatively correlated with calculated strain-energy release rates and it was found that the Mode I component of energy release dominates the growth process.

Whitcomb, J. D.↗

NASA NTRS1981

A sputtered zirconia primer for improved thermal shock resistance of plasma-sprayed ceramic turbine seals

It is shown that the application of sputtered Y2O3-stabilized ZrO2 (YSZ) primer in plasma-sprayed YSZ ceramic-coated turbine blades results in an improvement, by a factor of 5-6, in the thermal shock life of specimens with a sprayed, porous, Ni-Cr-Al-Y intermediate layer. Species with and without the primer were found to be able to survive 1000 cycles when the intermediate layer was used, but reduced laminar cracking was observed in the specimen with the primer. It is suggested that the sputtered YZS primer-induced properties are due to (1) more effective wetting and adherence of the plasma-sprayed YZS particles to the primer, and (2) the primer's retardation of impinging, molten plasma sprayed particles solidification rates, which result in a less detrimental residual stress distribution.

Bill, R. C.↗

NASA NTRS1982

Three dimensional finite element analysis of damage accumulation in composite laminate

A three dimensional finite-element computer program has been developed to analyze layered fiber-reinforced composite laminate. This program is capable of: (1) calculating the detailed stress distribution, (2) identifying the damage zone and mode of failure, (3) analyzing the damage accumulation, and (4) determining the ultimate strength of the composite laminate.

Lee, J. D.↗

NASA NTRS1982

Design and development of a ceramic radial turbine for the AGT101

An acceptable and feasible ceramic turbine wheel design has been achieved, and the relevant temperature, stress, and success probability analyses are discussed. The design is described, the materials selection presented, and the engine cycle conditions analysis parameters shown. Measured MOR four-point strengths are indicated for room and elevated temperatures, and engine conditions are analyzed for various cycle states, materials, power states, turbine inlet temperatures, and speeds. An advanced gas turbine ceramic turbine rotor thermal and stress model is developed, and cumulative probability of survival is shown for first and third-year properties of SiC and Si3N4 rotors under different operating conditions, computed for both blade and hub regions. Temperature and stress distributions for steady-state and worst-case shutdown transients are depicted.

Finger, D. G.↗