Search NASA⌕ Search

SEARCH · Search NASA

Results for “TIP SPEED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Flight Investigation of Effects of Selected Operating Conditions on the Bending and Torsional Moments Encountered by a Helicopter Rotor Blade

Flight tests have been conducted with a single-rotor helicopter to determine the effects of partial-power descents with forward speed, high-speed level turns, pull-outs from autorotation, and high-forward-speed high-rotor-speed autorotation on the flapwise bending and torsional moments of the rotor blade. One blade of the helicopter was equipped at 14 percent and 40 percent of the blade radius with strain gages calibrated to measure moments rather than stresses. The results indicate that the maximum moments encountered in partial-power descents with forward speed tend to be generally reduced from the maximum moments encountered during partid-power descents at zero forward speed. High-speed level turns and pull-outs from auto-rotation caused retreating-blade stall which produced torsional moments (values up to 2,400 inch-pounds). at the 14-percent-radius station that were as large as those encountered during the previous investigations of retreating-blade stall (values up t o 2,500 inch-pounds). High-forward- speed high-rotor-speed autorotation produced flapwise bending moments (values up to 7,200 inch-pounds) at the 40-percent-radius station which were as large as the flapwise bending moments (values up to 7,800 inch-pounds) a t the 14-percent-radius station encountered during partial - power vertical descents. The results of the present investigation (tip-speed ratios up to 0.325 and an unaccelerated level-flight mean lift coefficient of about 0.6), in combination with the related results of at zero forward speed produce the largest rotor-blade vibratory moments. However, inasmuch as these large moments occur only during 1 percent of the cycles and 88 percent of the cycles are at moment values less than 70 percent of these maximum values in partial-power descents, other conditions, such as high-speed flight where the large moments are combined with large percentages of time spent,must not be neglected in any rotor-blade service-life assessment.

Ludi, LeRoy H.↗
NASA NTRS1982

Noise reduction experience at Hughes Helicopter, Inc.

Noise reduction is mostly limited to light helicopters whose noise signature is dominated by their tail rotors. It is primarily hardware oriented. Well known noise reduction techniques such as reduction of rotor speeds with an accompanying increase in solidity to maintain performance, engine noise reduction with the use of exhaust mufflers, and acoustic blanketing of transmission and engine compartment are used. The concept of blade phasing as a means of reducing tail rotor noise is also used. Engine noise (exhaust noise), power train noise and airframe noise becomes important at low rotor tip speeds and means must be found to reduce these noise sources if further noise reductions are desired. The use of a special test rig aids in isolating the various noise sources and arriving at the penalties (performance or payload) involved in quieting them. Significant noise reduction are achieved for the light helicopter with minimum performance or weight penalties because of the dominance of a single noise source (the tail rotor).

D S Janakiram↗
NASA NTRS1932

Aerodynamic characteristics of circular-arc airfoils at high speeds

The aerodynamic characteristics of eight circular-arc airfoils at speeds of 0.5, 0.8, 0.95, and 1.08 times the speed of sound have been determined in an open-jet air stream 2 inches in diameter, using models of 1-inch chord. The lower surface of each airfoil was plane; the upper surface was cylindrical. As compared with the measurements described in NACA-TR-319, the circular-arc airfoils at speeds of 0.95 and 1.08 times the speed of sound are more efficient than airfoils of the R. A. F. or Clark Y families. At a speed of 0.5 times the speed of sound, the thick circular-arc sections are extremely inefficient, but thin sections compare favorably with those of the R. A. F. family. A moderate round of the sharp edges changes the characteristics very little and is in many instances beneficial. The results indicate that the section of the blades of propellers intended for use at high tip-speeds should be of the circular-arc form for the outer part of the blade and should be changed gradually to the R. A. F. or Clark Y form as the hub is approached.

Briggs, L J↗
NASA NTRS1985

Aerodynamic performance of a 27-percent-scale AH-64 wind-tunnel model with baseline/advanced rotor blades

Performance of a 27-percent scale model of an advanced rotor designed for the AH-64 helicopter was measured in hover and at forward speeds of 50 to 130 knots. A baseline rotor, modeled after the current AH-64 rotor, was also tested to provide data for comparison. The investigation was conducted to validate procedures used at Langley to design rotors with increased performance potential and to provide a database for evaluation of current and future rotor systems. Both rotors were operated at full-scale tip speeds. Rotor thrust, forward speed, and ground height were varied for each rotor.

Kelley, H. L.↗
DOE OSTI2024

Reinforcement Learning Control for Enhancing Marine Hydrokinetic Turbine Energy Generation

This paper proposes a reinforcement learning-based method to maximize power generation for a direct-drive marine hydrokinetic turbine. A high levelized cost of energy (LCOE) is preventative in the widespread adoption of many marine energy conversion technologies. A straightforward way to reduce LCOE is to increase conversion efficiency and ensure maximum energy generation. The proposed method utilizes a damping control methodology, varying applied generator torque via a linear relationship between the applied damping coefficient and rotor speed. A state-action-reward-state-action (SARSA) algorithm has been used to learn the optimal control action for a given flow velocity. The proposed SARSA methodology uses Gaussian radial basis functions to create a three-dimensional surface to estimate the relationship between damping coefficient, incoming flow velocity, and coefficient of power (C p ). Here, the SARSA algorithm was compared against a baseline optimal tip speed ratio controller over a year-long flow velocity case profile while considering the effects of biofouling on the turbine system, where the proposed RL method generated 0.92% more energy than the baseline.

Damp↗
NASA NTRS1966

Commerical application of rocket engine turbopump technology

This paper describes how commercial pump technology was modified for rocket engine application by trading long life for low weight. The component life of typical turbopump components is presented, and the modes of failure will be discussed. A comparison of the basic commercial and rocket engine pump requirements such as flow, pressure, etc. is made. It is concluded that rocket engine pump technology can be applied directly only if similar basic requirements exist in emergency or stand-by equipment. The specific design requirements for rocket engine turbopumps are presented and the need for high speeds is explained by the weight-speed relationship and the optimum NPSH of the tank and pump system. The trend of required rocket engine pump discharge pressure and future operational requirements is predicted. The need for inducers and boost pumps in rocket engines is explained, and the results of the flat-plate-inducer cavitation therein are briefly presented. Design solutions and material selections for high-pressure pump housings, ultra-high tip speed impellers, and pump packaging are demonstrated. As a typical example of utilizing rocket engine technology for commercial application, a helicopter stand-by engine i shown. This standby engine is designed from existing rocket engine components, using JATO rockets as the prime energy source.

Turbopump↗
NASA NTRS1975

A study of subsonic fan noise sources

Sources of noise in a 1.4 m (4.6 ft) diameter subsonic tip speed propulsive fan were studied using a combination of theoretical, experimental, and computer plotting techniques developed specially for noise diagnosis. To assess the structure of inlet turbulence, signals measured from pressure transducers on a rotor blade were plotted in a format to show the space-time history of inlet distortion. Ingested turbulence contained long, thin eddies which produce a tone-like noise component. Turbulence generated in the shroud boundary layer upstream of the rotor tips was found not to be an important noise source. However, this boundary layer does contain large amplitude disturbances caused by inlet turbulence which could be important in fans with thicker boundary layers. Theoretical calculations based on measured blade pressures show that rotor/inlet turbulence interaction and rotor/stator interaction are equally important sources of noise near the first three harmonics of blade passing frequency. At higher frequencies (above 2000 Hz) the rotor noise is dominant.

Hanson, D. B.↗
NASA NTRS1973

Application of holography to the determination of flow conditions within the rotating blade row of a compressor

The double-pulse, double-exposure holography technique was applied to visualize the flow field within a transonic compressor rotor with a tip speed of 1800 ft/sec. The principal objective was to visualize the shock waves created in the flow field which was supersonic relative to the rotating blade row. The upstream rotor blade bow shocks and, at high speed, the outermost portion of the leading edge passage shock were successfully observed in the holograms. Techniques were devised for locating these shocks in three dimensions, and the results were compared with theoretical predictions. Density changes between the two pulses due to motion of the shocks were large and, therefore, it was not possible to resolve the fringe systems in detail for the 100% speed conditions. However, gross features of the shocks were easily observed, and the upstream shocks were well displayed. In all cases the shock angles were somewhat larger than predicted by theory, and a distinct increase in angle near the outer wall was observed, which may be attributed to endwall boundary layer effects. The location and orientation of the observed leading edge passage shocks were in good agreement with static pressure contours obtained from measurements in the outer casing over the rotor tip.

Hantman, R. G.↗
NASA NTRS1983

Noise of the 10-bladed 60 deg swept SR-5 propeller in a wind tunnel

Noise generated by supersonic helical tip speed propellers is a possible cabin environment problem for future airplanes powered by these propellers. Noise characteristics of one of these propellers, designated SR-5, are presented. A matrix of tests was conducted to provide as much acoustic information as possible. During aerodynamic testing it was discovered that the propeller had an aeroelastic instability which prevented testing the propeller at its design advance ratio of 4.08 at axial Mach numbers over 0.7. Plots of the variation of the maximum blade passage tone with helical tip Mach number indicate that, at higher helical tip Mach numbers, the propeller operated on sharply increasing portion of the noise curve; therefore, extrapolations to the design condition would not be accurate. A possible extrapolation indicated that SR-5 at its design point should be quieter than SR-3 at its design point. Directivity plots at the higher helical tip Mach numbers indicate a lobed directivity pattern as was observed previously on the SR-3 propeller.

Dittmar, J. H.↗
NASA NTRS1973

Full scale hover test of a 25 foot tilt rotor

The tilt rotor underwent a hover performance test on the Aero Propulsion Laboratory whirl stand at Wright-Patterson Air Force Base. The maximum thrust over density ratio measured at the design tip speed of 740 feet per second was 10,016 pounds. This occurred when the power over density ratio was 1721 horsepower. At the hover overspeed rpm, the thrust and power, over density ratio, were 11,008 pounds and 1866 horsepower. During the test, the maximum measured thrust coefficient was 0.177, and the rotor figure of merit exceeded 0.81. Measured lifting efficiency was 8.35 pounds per horsepower at the thrust a 13,000-pound aircraft would require for hover at sea level on a standard day. No effect of compressibility on performance is discernible in the test results (the range of tip Mach numbers tested was 0.55 to 0.71).

Helf, S.↗
NASA NTRS1987

Measured noise of a scale model high speed propeller at simulated takeoff/approach conditions

A model high-speed advanced propeller, SR-7A, was tested in the NASA Lewis 9x15 foot anechoic wind tunnel at simulated takeoff/approach conditions of 0.2 Mach number. These tests were in support of the full-scale Propfan Text Assessment (PTA) flight program. Acoustic measurements were taken with fixed microphone arrays and with an axially translating microphone probe. Limited aerodynamic measurements were also taken to establish the propeller operating conditions. Tests were conducted with the propeller alone and with three down-stream wing configurations. The propeller was run over a range of blade setting angles from 32.0 deg. to 43.6 deg., tip speeds from 183 to 290 m/sec (600 to 950 ft/sec), and angles of attack from -10 deg. to +15 deg. The propeller alone BPF tone noise was found to increase 10 dB in the flyover plane at 15 deg. propeller axis angle of attack. The installation of the straight wing at minimum spacing of 0.54 wing chord increased the tone noise 5 dB under the wing of 10 deg. propeller axis angle of attack, while a similarly spaced inboard upswept wing only increased the tone noise 2 dB.

Woodward, Richard P.↗
NASA NTRS1984

Shutdown characteristics of the Mod-O wind turbine with aileron controls

Horizontal-axis wind turbines utilize partial or full variable blade pitch to regulate rotor speed. The weight and costs of these systems indicated a need for alternate methods of rotor control. Aileron control is an alternative which has potential to meet this need. The NASA Lewis Research Center has been experimentally testing aileron control rotors on the Mod-U wind turbine to determine their power regulation and shutdown characteristics. Experimental and analytical shutdown test results are presented for a 38 percent chord aileron-control rotor. These results indicated that the 38 percent chord ailerons provided overspeed protection over the entire Mod-O operational windspeed range, and had a no-load equilibrium tip speed ratio of 1.9. Thus, the 38 percent chord ailerons had much improved aerodynamic braking capability when compared with the first aileron-control rotor having 20 percent chord ailerons.

Miller, D. R.↗
NASA NTRS1987

Measured noise of a scale model high speed propeller at simulated takeoff/approach conditions

A model high-speed advanced propeller, SR-7A, was tested in the NASA Lewis 9 x 15 foot anechoic wind tunnel at simulated takeoff/approach conditions of 0.2 Mach number. These tests were in support of the full-scale Propfan Text Assessment (PTA) flight program. Acoustic measurements were taken with fixed microphone arrays and with an axially translating microphone probe. Limited aerodynamic measurements were also taken to establish the propeller operating conditions. Tests were conducted with the propeller alone and with three down-stream wing configurations. The propeller was run over a range of blade setting angles from 32.0 deg. to 43.6 deg., tip speeds from 183 to 290 m/sec (600 to 950 ft/sec), and angles of attack from -10 deg. to +15 deg. The propeller alone BPF tone noise was found to increase 10 dB in the flyover plane at 15 deg. propeller axis angle of attack. The installation of the straight wing at minimum spacing of 0.54 wing chord increased the tone noise 5 dB under the wing of 10 deg. propeller axis angle of attack, while a similarly spaced inboard upswept wing only increased the tone noise 2 dB.

Woodward, Richard P.↗
DOE OSTI2024

Development of Solid Synchronous Reluctance Rotors With Multi-Material Additive Manufacturing

Synchronous reluctance (SynR) machines are promising rare-earth material-free alternatives to permanent magnet machines. However, structural challenges limit their operating speed and power density. This paper proposes and investigates multi-material additive manufacturing (MMAM) as a key-enabler to realize power-dense and high-speed SynR machines. It does so by proposing designs that guide magnetic flux through solid rotors realized by selective placement of magnetic and non-magnetic materials. To explore this concept, first, material samples are additively manufactured and experimentally characterized to assess the structural and magnetic properties that can be expected for the proposed rotors. Second, the design space of each rotor type is explored using these measured properties within finite element analysis. The results reveal that MMAM can enable fabrication of SynR motors with power density levels that are at the leading edge of all conventional electric machine topologies. It is shown that tip speeds in excess of 300 m/s can be achieved, resulting in 3-4x improvement in power density over conventional SynR motors. A solid SynR rotor is printed in an experimental MMAM laser powder bed fusion system. The rotor is paired with an existing stator to create a functional SynR motor with a saliency ratio of 2.59 and torque rating of 4.15 Nm. This is the first publication of a SynR rotor prototype constructed via MMAM.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Low speed wind tunnel investigation of a large scale lift fan STOL transport model

The low-speed aerodynamic characteristics of large scale V/STOL transport models with lift fan and lift-cruise fan propulsion systems are discussed. The model of this investigation had two fans mounted side by side in the nose section of the fuselage. This permitted a reasonably deep inlet on the inboard side of each fan while the outboard side had a fairly shallow inlet. Lift-cruise fans were installed on the aft section of the fuselage. Hood-type deflection ducts were used to turn the fan flow from the cruise direction to the lift direction for STOL performance. Fan performance is shown for all four fans both statically and with crossflow. Longitudinal force and moment results are shown for a representative tip speed (forward speed) range through wing supported flight. Lateral-directional characteristics are also presented. The results are presented without analysis.

Atencio, A., Jr.↗
NASA NTRS1982

Evaluation of wind tunnel performance testings of an advanced 45 deg swept 8-bladed propeller at Mach numbers from 0.45 to 0.85

The increased emphasis of fuel conservation in the world and the rapid increase in the cost of jet fuel has stimulated a series of studies of both conventional and unconventional propulsion systems for commercial aircraft. The results of these studies indicate that a fuel saving of 15 to 30 percent may be realized by the use of an advanced high-speed turboprop (Prop-Fan) compared to aircraft equipped with high bypass turbofan engines of equivalent technology. The Prop-Fan propulsion system is being investigated as part of the NASA Aircraft Energy Efficient Program. This effort includes the wind tunnel testing of a series of 8 and 10-blade Prop-Fan models incorporate swept blades. Test results indicate efficiency levels near the goal of 80 percent at Mach 0.8 cruise and an altitude of 10.67 km (35,000 ft). Each successive swept model has shown improved efficiency relative to the straight blade model. The fourth model, with 45 deg swept blades reported herein, shows a net efficiency of 78.2 at the design point with a power loading of 301 kW/sq meter and a tip speed of 243.8 m/sec (800 ft/sec.).

Rohrbach, C.↗
NASA NTRS1984

Aeromechanical stability of a full-scale hingeless rotor in hover

The aeroelastic stability in hover of a 9.8-m-diam, hingeless helicopter rotor system is evaluated. Rotor inplane damping data were obtained for rotor operation between 350 and 425 rpm for thrust coefficients between 0.0 and 0.12. At constant rotor rotational speed, a minimum inplane damping level was obtained at a thrust coefficient of approximately 0.02. At constant rotor thrust, a minimum in rotor inplane damping was measured at 400 rpm. Correlation with a comprehensive aeroelastic stability program is found to be good. The influence of different aerodynamic inflow models on predicted damping levels is shown. Best correlation with experimental data is obtained using a dynamic inflow model rather than static or quasi-static inflow models. Comparison with other full-scale, hingeless rotor stability data in hover is presented. Also, direct comparisons are made with data from a full-scale bearingless main rotor test performed on the same general-purpose test apparatus. Although the bearingless rotor is more highly damped at design tip speed and 1-g thrust operation, greater sensitivity to operating conditions is shown.

Peterson, R. L.↗
NASA NTRS2014

Enhanced Fan Noise Modeling for Turbofan Engines

This report describes work by consultants to Diversitech Inc. for the NASA Glenn Research Center (GRC) to revise the fan noise prediction procedure based on fan noise data obtained in the 9- by 15 Foot Low-Speed Wind Tunnel at GRC. The purpose of this task is to begin development of an enhanced, analytical, more physics-based, fan noise prediction method applicable to commercial turbofan propulsion systems. The method is to be suitable for programming into a computational model for eventual incorporation into NASA's current aircraft system noise prediction computer codes. The scope of this task is in alignment with the mission of the Propulsion 21 research effort conducted by the coalition of NASA, state government, industry, and academia to develop aeropropulsion technologies. A model for fan noise prediction was developed based on measured noise levels for the R4 rotor with several outlet guide vane variations and three fan exhaust areas. The model predicts the complete fan noise spectrum, including broadband noise, tones, and for supersonic tip speeds, combination tones. Both spectra and directivity are predicted. Good agreement with data was achieved for all fan geometries. Comparisons with data from a second fan, the ADP fan, also showed good agreement.

aircraft↗