Search NASA⌕ Search

SEARCH · Search NASA

Results for “TUNNELING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

The self streamlining wind tunnel

A two dimensional test section in a low speed wind tunnel capable of producing flow conditions free from wall interference is presented. Flexible top and bottom walls, and rigid sidewalls from which models were mounted spanning the tunnel are shown. All walls were unperforated, and the flexible walls were positioned by screw jacks. To eliminate wall interference, the wind tunnel itself supplied the information required in the streamlining process, when run with the model present. Measurements taken at the flexible walls were used by the tunnels computer check wall contours. Suitable adjustments based on streamlining criteria were then suggested by the computer. The streamlining criterion adopted when generating infinite flowfield conditions was a matching of static pressures in the test section at a wall with pressures computed for an imaginary inviscid flowfield passing over the outside of the same wall. Aerodynamic data taken on a cylindrical model operating under high blockage conditions are presented to illustrate the operation of the tunnel in its various modes.

Goodyer, M. J.↗
NASA NTRS1975

Development of minimum correction wind tunnels

Flow distortions due to wind tunnel wall interference may be accounted for if the model to tunnel ratio is small, but the theory becomes less reliable as the model becomes larger. This paper presents theoretical analysis and experimental evidence which supports a new concept of wind tunnel. The method employs active control of flow through the walls so that the model is in approximately free air conditions during the test. Practical considerations in the design of such a tunnel are presented. Results indicate that a minimum correction wind tunnel may be achieved with active walls of relatively low porosity.

Bernstein, S.↗
NASA NTRS1974

Tunneling in thin MOS structures

Recent results on tunneling in thin MOS structures are described. Thermally grown SiO2 films in the thickness range of 22-40 A have been shown to be effectively uniform on an atomic scale and exhibit an extremely abrupt oxide-silicon interface. Resonant reflections are observed at this interface for Fowler-Nordheim tunneling and are shown to agree with the exact theory for a trapezoidal barrier. Tunneling at lower fields is consistent with elastic tunneling into the silicon direct conduction band and, at still lower fields, inelastic tunneling into the indirect conduction band. Approximate dispersion relations are obtained over portions of the silicon-dioxide energy gap and conduction band.

Maserjian, J.↗
NASA NTRS1976

Experiments with a self-correcting wind tunnel

The feasibility of controlling the flow actively through the walls of a transonic, porous wall wind tunnel in order to minimize wall interference effects on a test model is demonstrated. The method is based upon measuring the components of the disturbance velocity at discrete points along an imaginary surface in the flow field within the tunnel. A mathematical formulation of the flow field exterior to the surface including the boundary condition for unconfined flow, i.e., that all disturbance vanish at infinite, is used to determine if these measured velocity components are consistent with that boundary condition. If they are not, the theory provides a better approximation to the velocity component for unconfined flow, and the flow through the tunnel walls is readjusted iteratively until the measured quantities are consistent with unconfined flow. A brief review of theoretical methods is followed by a description of the Calspan self correcting wind tunnel design and operation, calibration with and without active wall control. Typical results obtained by approximating a conventional porous wall wind tunnel for an 0012 airfoil show that active wall control largely reproduces the correct shock wave position, eliminates wall interference of lift and drag, and reduces the interference effects on pitching moment to 10%.

Vidal, R. J.↗
NASA NTRS1975

Measurement of flow fields in a large transonic wind tunnel using a laser velocimeter

An investigation to determine the feasibility of using a laser velocimeter for measuring the mean flow velocities about airplane models in the Langley 16-foot transonic tunnel has recently been completed. The laser velocimeter was a two-component fringe-type used in the back scatter mode. The tunnel airflow was seeded with oil droplets to provide scattering sources for the laser velocimeter. Measurements of the tunnel free-stream velocity were in good agreement with the tunnel calibration, and measurements of the velocity along the stagnating streamline of a hemisphere model, when adjusted for particle lag, were in good agreement with theoretical predictions. The study showed that the laser, optics, and electronics system operated satisfactorily, but that further development is required to reduce scattering particle size and substance accumulation in the tunnel.

Putnam, L. E.↗
NASA NTRS1976

Flight effects on JT8D engine jet noise as measured in the NASA Ames 40-by 80-foot wind tunnel

A JT8D-17 turbofan engine was tested in a 40 x 80 ft wind tunnel to determine flight effects on jet noise. The engine was configured as a baseline with conical nozzle, a quiet nacelle 20-lobe ejector/suppressor, and an internal mixer with conical nozzle. Tunnel-off and tunnel-on noise tests were conducted over a range of nozzle pressure ratios (1.2 to 2.1), primary jet velocities (275 to 550 m/s), and tunnel velocities up to 100 m/s. Aft quadrant noise data were measured by a pair of traversing microphones located on a 3-m sideline relative to the engine centerline. Unique correlations and analysis procedures were developed in order to define far-field flight effects from the relatively near-field noise measurements. The ejector/suppressor experienced a significant loss of suppression relative to static measurements during flight while the internal mixer indicated a slight gain in suppression. It is concluded that the wind tunnel is a viable method for studying flight effects on engine jet noise.

Strout, F. G.↗
NASA NTRS1976

Correlation microphone for measuring airframe noise in large-scale wind tunnels

A correlation microphone arrangement was used in the test section of the Ames 7- by 10-Foot and 40- by 80-Foot Wind Tunnels in an attempt to reject the reverberant and wind noise. The tests in the 7- by 10-foot wind tunnel covered a frequency range from 400 Hz to 8 kHz while the tests in the 40- by 80-foot tunnel covered the range from 31.5 to 800 Hz. Examination of the experimental data plus calculations of cross-correlations due to reflective noise indicate that the correlation microphone is effective in rejecting microphone wind noise and reverberant noise even at low frequencies, and that the low-frequency background noise monitored by the correlation microphone is reflected noise with a preferred direction from the tunnel drive system. Design studies indicate that this tunnel drive noise can be reduced substantially through suitable modification of the drive fans and acoustical treatment of the nacelles that house these fans.

Ahtye, W. F.↗
NASA NTRS1977

Transonic wind-tunnel wall interference

A method for analyzing wall interference is described which avoids the assumption of linear superposition of perturbations in extracting the wall induced velocity field. Measurements of pressure distribution on or near the tunnel walls during the actual wind tunnel test, are imposed as boundary values to be matched. Instead of applying wall interference corrections to the wind tunnel data, some property of the wall is adjusted until a calculated interference free criterion is satisfied for each tunnel data point. The mode of operation for the National Transonic Facility, envisioned as a correctable interference transonic tunnel, combines the capability for accurate assessment of wall interference with a limited capability for wall control.

Kemp, W. B., Jr.↗
NASA NTRS1976

Simulation of flight-type engine fan noise in the NASA-Lewis 9 x 15 anechoic wind tunnel

A major problem in the measurement of aircraft engine fan noise is the difficulty of simulating, in a ground-based facility, the noise that occurs during flight. Flight-type noise as contrasted to the usual ground-static test noise exhibits substantial reductions in both (1) the time unsteadiness of tone noise and (2) the mean level of tones calculated to be nonpropagating or cut-off. A model fan designed with cut-off of the fundamental tone was acoustically tested in the anechoic wind tunnel under both static and tunnel flow conditions. The properties that characterize flight-type noise were progressively simulated with increasing tunnel flow. The distinctly lobed directivity pattern of propagating rotor/stator interaction modes was also observed. The results imply that the excess noise attributed to the ingestion of the flow disturbances that prevail near most static test facilities was substantially reduced with tunnel flow. The anechoic wind tunnel appears to be a useful facility for applied research on aircraft engine fan noise under conditions of simulated flight.

Heidmann, M. F.↗
NASA NTRS1977

Measurement of model aeroelastic deformations in the wind tunnel at transonic speeds using stereophotogrammetry

A stereophotographic method of determining the aeroelastic deformations of an airplane model under aerodynamic load in the wind tunnel was evaluated. Wind tunnel tests were conducted in the Langley 8 foot transonic pressure tunnel on the wing of a 0.0625 scale model of the TF-8A supercritical wing research airplane to obtain simultaneously the aerodynamic forces and moments, pressure distributions, and stereophotographs. Tests were conducted at Mach numbers of 0.80, 0.95, and 1.20, and at free stream dynamic pressures of 20,349 Pa and 40,698 Pa. Accuracy of the stereophotographic technique in determining wing deflections was within 0.013 cm under static conditions. This value translates to an error in wing twist of 0.10 deg inboard and increases to 0.20 deg outboard. When the model was under aerodynamic load in the wind tunnel, the accuracy of the stereophotographic technique of determining wind deflections increased to 0.052 cm when compared with static wing loadings because of the dynamic motion of the model in the tunnel.

Brooks, J. D.↗
NASA NTRS1978

Self streamlining wind tunnel: Further low speed testing and final design studies for the transonic facility

Work was continued with the low speed self streamlining wind tunnel (SSWT) using the NACA 0012-64 airfoil in an effort to explain the discrepancies between the NASA Langley low turbulence pressure tunnel (LTPT) and SSWT results obtained with the airfoil stalled. Conventional wind tunnel corrections were applied to straight wall SSWT airfoil data, to illustrate the inadequacy of standard correction techniques in circumstances of high blockage. Also one SSWT test was re-run at different air speeds to investigate the effects of such changes (perhaps through changes in Reynold's number and freestream turbulence levels) on airfoil data and wall contours. Mechanical design analyses for the transonic self-streamlining wind tunnel (TSWT) were completed by the application of theoretical airfoil flow field data to the elastic beam and streamline analysis. The control system for the transonic facility, which will eventually allow on-line computer operation of the wind tunnel, was outlined.

Wolf, S. W. D.↗
NASA NTRS1978

Transonic assessment of two-dimensional wind tunnel wall interference using measured wall pressures

A method is described for assessing wall interference in two dimensional wind tunnels with better realism and accuracy than is achieved with methods based on classical wall interference theory. Measured pressure distributions were imposed as boundary conditions on a nonlinear transonic form of the potential equation to obtain an accurate computational reproduction of the actual tunnel flow. Wall-induced velocity perturbations were then extracted to yield both corrections to the tunnel test conditions and a measure of the adequacy of these corrections to account for tunnel interference. Application of the method to a transonic tunnel with variable porosity walls is illustrated.

Kemp, W. B., Jr.↗
NASA NTRS1978

A surface flow visualisation technique for use in cryogenic wind tunnels

A method of surface flow visualization for use in cryogenic wind tunnels is described which requires injection of a cryogenic liquid onto the model while the tunnel is running. This necessitates the use of a substance that remains liquid over a large range of cryogenic wind tunnel operating temperatures. It is found that propane (C3H8) is a suitable substance. Experiments are conducted in a subsonic cryogenic wind tunnel to assess the practical application of liquid propane flow visualization. The propane is stored in a chamber cooled by liquid nitrogen and when required is pumped through pipes to a gallery inside the model and then out onto the surface through small holes. To color the liquid a suspension of pigment particles is used. Propane is supplied to the cooled chamber in gaseous form from a standard liquefied gas cylinder. The sequence of events is illustrated on a propane temperature-entropy diagram. The use of liquefied propane for flow visualization in a cryogenic tunnel operating at pressures up to 40 atm appears to be feasible. Illustrative examples are provided.

Kell, D. M.↗
NASA NTRS1979

Preliminary flight and wind tunnel comparisons of the inlet/airframe interaction of the F-15 airplane

Preliminary flight and wind tunnel comparison data are presented for the F-15 inlet/airframe interactions program. Test conditions and instrumentation for both the model and the aircraft are described. Flight and wind tunnel inlet drag data (for a 0-deg angle of attack and Mach numbers of 0.6, 0.9, and 1.2), derived by using nearly identical pressure integration equations, are compared. The effects of a movable cowl, movable ramps, and other system components on pressure flow fields along the airframe are discussed. Excellent agreement between wind tunnel and flight pressure-integrated drags is found at all three Mach numbers. The wind tunnel data show good agreement for pressure-integrated and force-balance-measured inlet drag, except at Mach 0.6. Flight-measured pressure-integrated inlet lift is lower than that measured in the wind tunnel.

Webb, L. D.↗
NASA NTRS1979

Effect of viscosity on wind-tunnel wall interference for airfoils at high lift

The effect of the walls of a wind tunnel on the subsonic, two-dimensional flow past airfoils at high angles of attack is studied theoretically and experimentally. The computerized analysis, which is based on iteratively coupled potential-flow, boundary-layer, and separated-flow analyses, includes determining the effect of viscosity and flow separation on the airfoil/wall interaction. Predictions of the effects of wind-tunnel wall on the lift of airfoils are compared with wall corrections based on inviscid image analyses, and with experimental data. These comparisons are made for airfoils that are large relative to the size of the test section of the wind tunnel. It is shown that the inviscid image modeling of the wind-tunnel interaction becomes inaccurate at lift coefficients near maximum lift or when the airfoil/wall interaction is particularly strong. It is also shown that the present method of analysis (which includes boundary-layer and flow-separation effects) will provide accurate wind-tunnel wall corrections for lift coefficients up to maximum lift.

Olson, L. E.↗
NASA NTRS1979

Evaluation of a wind-tunnel gust response technique including correlations with analytical and flight test results

A wind tunnel technique for obtaining gust frequency response functions for use in predicting the response of flexible aircraft to atmospheric turbulence is evaluated. The tunnel test results for a dynamically scaled cable supported aeroelastic model are compared with analytical and flight data. The wind tunnel technique, which employs oscillating vanes in the tunnel throat section to generate a sinusoidally varying flow field around the model, was evaluated by use of a 1/30 scale model of the B-52E airplane. Correlation between the wind tunnel results, flight test results, and analytical predictions for response in the short period and wing first elastic modes of motion are presented.

Redd, L. T.↗
NASA NTRS1980

Scale model studies for establishing the flow patterns of a low-speed tunnel

Experiments were conducted in a model tunnel scaled down in a ratio of 1:24 from the full size prototype V/STOL tunnel at NASA Langley Research Center. The flow characteristics around the tunnel were studied and the location and causes of local flow separation and local recirculation were documented. The study of the interaction between the various components from which the tunnel is built, an experimental setup similar to the sequence of tunnel circuit components was constructed which enabled the various components to be tested either individually or in combination. The components were tested by the simple technique of blowing air through them, then measuring the velocity distribution at relevant sections.

Barna, P. S.↗
NASA NTRS1980

TWINTAN: A program for transonic wall interference assessment in two-dimensional wind tunnels

A method for assessing the wall interference in transonic two dimensional wind tunnel test was developed and implemented in a computer program. The method involves three successive solutions of the transonic small disturbance potential equation to define the wind tunnel flow, the perturbation attriburable to the model, and the equivalent free air flow around the model. Input includes pressure distributions on the model and along the top and bottom tunnel walls which are used as boundary conditions for the wind tunnel flow. The wall induced perturbation fields is determined as the difference between the perturbation in the tunnel flow solution and the perturbation attributable to the model. The methodology used in the program is described and detailed descriptions of the computer program input and output are presented. Input and output for a sample case are given.

Kemp, W. B., Jr.↗