Search NASA⌕ Search

SEARCH · Search NASA

Results for “Thermal Insulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Beryllium Oxide (BeO) Handbook

Beryllium oxide (BeO) is an oxide ceramic material. BeO ceramics provide thermal conductivity second only to diamond among electrically insulating materials, dissipating nearly 300 W/mK at room temperature. This property leads to electronic applications for BeO. BeO has a thermal expansion coefficient intermediate between gallium arsenide and refractory metal composites. Its low dielectric constant (6.7) and low loss index (0.0012 at 1 MHz) permits electrical circuit performance at high frequencies. It is employed as a window material for high frequency microwave applications. BeO is very stable under oxidizing and reducing high temperature and high humidity environments, unlike nitrides which will decompose to their oxide equivalent. Similar to beryllium metal, BeO acts as a scatterer of neutrons and is used as a neutron moderator material in nuclear reactor applications. The largest use of BeO is as the raw material for the manufacture of beryllium-copper alloys, followed closely as the raw material for conversion to beryllium metal. Most of the research performed on BeO was conducted in the 1960’s and 1970’s. 75% of the references cited in this Handbook are from the time period 1960-1980. Up to 1995, there were three commercial sources of BeO: Materion Corporation, Eagle-Picher, and Ceradyne Corporation. However, since 1995 Eagle-Picher and Ceradyne no longer supply BeO commercial products. Thus, the only current commercial source of BeO materials is Materion Corporation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Bio-Based Phase Change Materials (PCMs) for Thermal Energy Storage (Final Scientific/Technical Report)

The goal of this project is to develop a novel bio-based phase change material (PCM) derived from squid ring teeth (SRT) proteins, and design a prototype heat exchanger based on these bio-based PCMs for energy storage and dynamic heat exchange for building thermal energy storage systems. The PCMs, derived from SRT proteins, will demonstrate room temperature energy storage capacities and switchable thermal conductivities that redefine the current state-of-the-art (SOA) for building thermal energy storage. Further, in a single material and with a single manufacturing processes, our proposed thermal battery will be developed with “on demand” thermal conductivity for rapid charging/discharging but superior insulation during energy storage periods. More specifically, our bio-based PCMs have demonstrated: 1) the potential for increased energy storage capacity (i.e., greater than paraffines at room temperature); 2) tunability in thermal conductivity with the largest thermal conductivity switching ratios for an intrinsic material reported to date, and 3) a 100% recyclable and biodegradable PCM with low volatility and toxicity and scalability in its manufacture for both residential and commercial applications. The already established ability for roll-to-roll processing of these non-toxic, non-flammable SRT composites along with their carbon-neutral manufacturing processes that has been pioneered by our team make this solution a disruptive and impactful technology to redefine the current SOA of energy storage technologies. The outcomes of this effort have been: 1) the identification of new bio-based PCM that establishes a new SOA for thermal conductivity and energy storage density at room temperature and 2) the development of a new experimental technique to measure the energy storage density via latent heat measurements during melting of thin films. This new technique can be applied to thin films (as thin as < 1 micrometer), and represents a novel approach for thin film energy storage density measurements. Dynamic thermal energy storage is the missing technology that will enable a grid- interactive efficient building (GEB). For a “smart” building capable of connecting with the power grid, the media must be inexpensive and possess thermal switching capabilities to control the time-dependent heat flow into (and out of) the PCM on demand. Unique to the material system in this program, programmable SRT-based PCM show improvements as compared to traditionally used PCMs, and thus its technical performance will represent a leap forward for the future GEB concept.

25 ENERGY STORAGE↗
DOE OSTI2022

Studying the Suitability of Nineteen Lignins as Partial Polyol Replacement in Rigid Polyurethane/Polyisocyanurate Foam

In this study, nineteen unmodified lignins from various sources (hardwood, softwood, wheat straw, and corn stover) and isolation processes (kraft, soda, organosolv, sulfite, and enzymatic hydrolysis) were used to replace 30 wt.% of petroleum-based polyol in rigid polyurethane/polyisocyanurate (PUR/PIR) foam formulations. Lignin samples were characterized by measuring their ash content, hydroxyl content (Phosphorus Nuclear Magnetic Resonance Spectroscopy), impurities (Inductively Coupled Plasma), and pH. After foam formulation, properties of lignin-based foams were evaluated and compared with a control foam (with no lignin) via cell morphology, closed-cell content, compression strength, apparent density, thermal conductivity, and color analysis. Lignin-based foams passed all measured standard specifications required by ASTM International C1029-15 for type 1 rigid insulation foams, except for three foams. These three foams had poor compressive strengths, significantly larger cell sizes, darker color, lower closed-cell contents, and slower foaming times. The foam made with corn stover enzymatic hydrolysis lignin showed no significant difference from the control foam in terms of compressive strength and outperformed all other lignin-based foams due to its higher aliphatic and p-hydroxyphenyl hydroxyl contents. Lignin-based foams that passed all required performance testing were made with lignins having higher pH, potassium, sodium, calcium, magnesium, and aliphatic/p-hydroxyphenyl hydroxyl group contents than those that failed.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Interfacial thermal transport in spin caloritronic material systems

Interfaces often govern the thermal performance of nanoscale devices and nanostructured materials. As a result, accurate knowledge of thermal interface conductance is necessary to model the temperature response of nanoscale devices or nanostructured materials to heating. Here, we report the thermal boundary conductance between metals and insulators that are commonly used in spin-caloritronic experiments. We use time-domain thermoreflectance to measure the interface conductance between metals such as Au, Pt, Ta, Cu, and Al with garnet and oxide substrates, e.g., NiO, yttrium iron garnet (YIG), thulium iron garnet (TmIG), Cr 2 O 3 , and sapphire. We find that, at room temperature, the interface conductance in these types of material systems range from 50 to 300 MW m –2 K –1 . Furthermore, we also measure the interface conductance between Pt and YIG at temperatures between 80 and 350 K. At room temperature, the interface conductance of Pt/YIG is 170 MW m –2 K –1 and the Kapitza length is ~40 nm. A Kapitza length of 40 nm means that, in the presence of a steady-state heat current, the temperature drop at the Pt/YIG interface is equal to the temperature drop across a 40-nm-thick layer of YIG. At 80 K, the interface conductance of Pt/YIG is 60 MW m –2 K –1 , corresponding to a Kapitza length of ~300 nm.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Spin current generation and detection in uniaxial antiferromagnetic insulators

Spin current represents a flow of spin angular momentum and does not require movement of charges. Magnetic insulators can therefore work as a source as well as a medium of spin currents, which has been established in ferrimagnetic insulators. Here, we report recent progress in the generation and electrical detection of spin currents in uniaxial antiferromagnetic insulators carried by antiferromagnetic magnons, both thermally and resonantly excited, respectively, via the spin Seebeck effect and antiferromagnetic spin pumping by subterahertz microwaves. These findings open up many exciting possibilities of potential antiferromagnetic applications.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2026

Toward durable stacks: glass-ceramic sealants for intermediate-temperature protonic ceramic electrochemical systems

Protonic ceramic electrochemical cells (PCECs) are emerging as promising technologies for efficient energy conversion and hydrogen production because they operate at intermediate temperatures with improved efficiency and durability compared with conventional solid oxide electrochemical cells. However, the long-term reliability and commercialization of PCEC stacks remain strongly limited by the performance of sealants, which are required to maintain gas tightness, electrical insulation, and mechanical integrity under harsh thermal and chemical environments. Among various sealing approaches, glass-ceramic sealants are considered the most practical and scalable due to their excellent wettability, chemical tunability, and strong interfacial adhesion. This review provides a comprehensive overview of recent advances in glass-ceramic sealants for intermediate-temperature protonic ceramic electrochemical systems. The fundamental design principles of sealant compositions are first discussed, followed by recent developments in deposition methods, sintering strategies, surface treatments, and degradation monitoring techniques. Particular attention is given to the unique challenges associated with PCEC operating conditions, including hydrothermal degradation, interfacial reactions with barium-containing electrolytes, and thermal mismatch. Finally, future opportunities involving sustainable materials, multiscale modeling, additive manufacturing, and artificial intelligence-assisted sealant optimization are highlighted.

glass–ceramic sealants↗
DOE OSTI2020

Structural, magnetic, and electronic evolution of the spin-ladder system BaFe 2 S 3-x Se x with isoelectronic substitution

We reWe report experimental studies of a series of BaF e 2 S 3 - x Se x ( 0 ≤ $x$ ≤ 3 ) single crystals and powder specimens using x-ray diffraction, neutron-diffraction, muon-spin-relaxation, and electrical transport measurements. A structural transformation from $C$ $mcm$ ( BaFe 2 Se 3 ) to $P$ $nma$ ( BaFe 2 Se 3 ) was identified around $x$ = 0.7 - 1 . Neutron-diffraction measurements on the samples with $x$ = 0.2, 0.4, and 0.7 reveal that the Néel temperature of the stripe antiferromagnetic order is gradually suppressed from ~120 to 85 K, while the magnitude of the ordered Fe 2+ moments shows very little variation. Similarly, the block antiferromagnetic order in BaFe 2 Se 3 remains robust for 1.5 ≤ $x$ ≤ 3 with negligible variation in the ordered moment and a slight decrease of the Néel temperature from 250 K ( $x$ = 3 ) to 225 K ( $x$ = 1.5 ). The sample with $x$ = 1 near the $C$ $mcm$ and $P$ $nma$ border shows coexisting, two-dimensional, short-range stripe- and block-type antiferromagnetic correlations. The system remains insulating for all $x$ , but the thermal activation gap shows an abrupt increase when traversing the boundary from the $C$ $mcm$ stripe phase to the $P$ $nma$ block phase. The results demonstrate that the crystal structure, magnetic order, and electronic properties are strongly coupled in the BaFe 2 S 3-x Se x system.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Low-temperature spin Seebeck effect in nonmagnetic vanadium dioxide

The spin Seebeck effect (SSE) is sensitive to thermally driven magnetic excitations in magnetic insulators. Vanadium dioxide in its insulating low-temperature phase is expected to lack magnetic degrees of freedom, as vanadium atoms are thought to form singlets upon dimerization of the vanadium chains. Instead, we find a paramagnetic SSE response in V⁢O 2 films that grows as the temperature decreases below 50 K. The field and temperature-dependent SSE voltage is qualitatively consistent with a general model of paramagnetic SSE response and inconsistent with triplet spin transport. Quantitative estimates find a spin Seebeck coefficient comparable in magnitude to that observed in strongly magnetic materials. Finally, the microscopic nature of the magnetic excitations in V⁢O 2 requires further examination.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Principal Component Analysis of Nuclear Cable Insulation Subjected to Elevated Temperature and Gamma Radiation

In nuclear power plants (NPPs), the aging of electrical cable insulation occurs due to elevated temperature, ionizing radiation, and other environmental factors. To ensure the safe and efficient operation of NPPs, determination of key indicators of cable aging is critical to predict the remaining useful lifetime of electrical cable insulation. In this work, the effects of simultaneous and sequential thermal and gamma radiation on the aging of cross-linked polyethylene (XLPE) electrical cable insulation are investigated. The chemical changes of the insulation were monitored non-destructively through the use of Fourier transform infrared (FTIR) spectroscopy. The FTIR spectra were measured stepwise after predetermined exposure intervals, with a total irradiation dose up to 320 kGy at a dose rate of 300 Gy/hr in two exposure scenarios; simultaneously aged samples were heated at 150 °C during irradiation, while sequentially aged samples were heated at 150 °C for designated durations followed by corresponding times of irradiation at ambient temperature. A data-driven approach using principal component analysis (PCA) was developed to highlight changes in the carbonyl region of the infrared spectra of the aged samples due to oxidation and to differentiate oxidation rates under the simultaneous and sequential exposure conditions. Findings indicate that the sequential aging scenario may be more conservative than the simultaneous aging scenario for XLPE electrical cable insulation.

Li, Donghui↗
DOE OSTI2024

REBCO Insert Coils toward High-Field, Large-Bore Magnet for Quantum Physics Research

High-temperature superconducting (HTS) magnets offer a promising solution for generating high magnetic fields efficiently and economically, serving as a vital component in nextgeneration scientific instruments and carbon-neutral power systems, notably in cost-effective compact fusion reactors. These high magnetic fields play a pivotal role in advancing research on quantum materials, particularly in elucidating the intricate electronic states near magnetic phase transitions. Here, this paper delves into the research conducted at the Princeton Plasma Physics Laboratory, which is divided into three phases aimed at overcoming technical hurdles in creating large-bore, high-field HTS magnets for cutting-edge quantum physics research. In Phase 1, we designed, constructed, and tested a compact REBCO solenoidal magnet comprising six double-pancake coils featuring a 41.3-mm inner diameter and a 70.0-mm outer diameter. It adopts a no-insulation approach to ensure electrical and thermal stability. Successful testing in a saturated liquid nitrogen bath confirmed its capability to generate a 0.8-T field at 77 K and 2 T at 65 K, with ongoing integration into liquid helium testing. Building on this experience, Phase 2 involves the design of an HTS insert coil, intended to nest within a 12-T low-temperature superconducting (LTS) outsert to achieve a minimum of 20 T at 4.2 K. The focus of Phase 2 centers on addressing challenges posed by screening-current (SC) effects, particularly the associated stress/strain issues. Employing a numerical model that fully couples the SC and mechanical analysis, we discuss strategies for managing stress to mitigate the effects of SCinduced stress concentrations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Draft Environmental Impact Statement for Proposed Energy Conservation Standards for Manufactured Housing

This draft environmental impact statement (EIS) analyzes the impacts related to DOE’s proposed energy conservation standards for manufactured homes. DOE’s proposed energy conservation standards are based on the 2021 International Energy Conservation Code (IECC) and relate to the building thermal envelope; air sealing; installation of insulation; duct sealing; heating, ventilation and air conditioning (HVAC); service hot water systems; mechanical ventilation fan efficacy; and heating and cooling equipment sizing. The draft EIS evaluates DOE’s proposed action (energy conservation standards tiered based the manufacturers retail list price), alternatives to the proposed action (including energy conservation standards tiered based on size of the manufactured home and untiered standards), and a no action alternative. The draft EIS presents analysis of impacts related to (1) energy resources; (2) air resources (including greenhouse gases, climate change, ambient air quality and indoor air quality); (3) health and safety; (4) socioeconomics; and (5) environmental justice.

MacDonell, Margaret↗
DOE OSTI2023

Crosslinking of loose insulating powders

Described herein are materials and methods useful in the field of insulation, including building materials, refrigeration, cryogenics, and shipping, amongst others. Advantageously, the provided materials and method provide low thermal conductivities and increased mechanical strength, allowing for efficient insulating in a diverse range of applications. The provided materials and methods include individual particles connected by a polymer network that links individual particles and may include hollow or evacuated capsules and various strengthening agents.

Simpson, Lin Jay↗
DOE OSTI2024

Advanced Packaging Designs

The primary deliverable for this project will be to construct a power electronics package utilizing an organic, electrically insulating substrate material and demonstrate superior thermal performance and greater reliability under thermal cycling, thermal aging, vibration, power cycling, and electrical high-potential evaluation over traditional packages.

ENGINEERING↗
DOE OSTI2025

Advanced Computational Modeling of High-Level Waste Vitrification at the Hanford Site

The U.S. Department of Energy (DOE) has selected vitrification for stabilizing legacy tank waste at the Hanford site, where radioactive waste from plutonium production was historically stored in underground tanks. This waste will be separated into low-activity waste (LAW) and high-level waste (HLW) fractions and processed at the Waste Treatment and Immobilization Plant (WTP). At WTP, glass melters are used for the vitrification of radioactive tank waste, transforming it into a stable borosilicate glass form for safe long-term storage. The melter vessel is constructed from highly durable and heat-resistant materials, where the vitrification process occurs. The main regions that are modeled are the melt pool, plenum, cold cap, riser/discharge chamber, and surrounding structure with insulation layers. Forced convection induced by air bubblers at the base of the melter ensure uniform temperature distribution and provide heat to the cold cap layer. The cold cap is a region of reacting batch feed that floats on top of the molten glass and is where the batch-to-glass reactions occur. Joule heating provided by electrodes mounted along the vertical walls of the melter and immersed directly in the glass, generates the necessary heat for the net endothermic conversion processes that occur in the cold cap. The high temperatures, radioactivity, and opaque nature of the glass prevent direct observation inside the melters. Therefore, computational models are essential for providing insight into factors that affect melter throughput. Thermocouples in the plenum provide operators with plenum temperature measurements. Operational adjustments include bubbling rate, voltage supplied to the electrodes, feed adjustments, and glass removal rate. Different computational fluid dynamics (CFD) models have been developed, each serving a specific purpose. There are CFD models of different scale melters, as well as models that capture the two-phase flow interfaces of rising bubbles in the molten glass or models with a simplified molten glass region so that the surrounding structure and plenum can be feasibly incorporated. Pilot-scale melter models have been developed to serve as validation of the methods employed in the simulation of the full-scale WTP melters. Models incorporating resolved bubbling are used to develop momentum source terms to implement into a single phase, multi-region, steady-state flow model that is being validated by measured process parameters such as glass production rate, voltage, input power, plenum temperatures, etc. The resolved bubbling model uses the multiphase volume of fluid approach to model the system with a high-resolution interface capturing scheme to maintain sharp interfaces between the molten glass and the air phase. The suite of CFD models is continually being improved to incorporate more realistic physics and achieve faster turnaround time. For example, an incremental controller is implemented to automatically adjust electrode voltage within the simulation to a molten glass set point temperature of 1150°C. Newer models feature improved meshes to ensure conformal meshes between regions and eliminate unnecessary mesh refinement in areas that are not of interest (such as boundary layers in offgas ports). Instead of explicitly modeling the structural, refractory, and insulation layers of the melter, a thermal resistance approach is used with published correlations used for boundary conditions. The development of robust and efficient CFD models will be instrumental in enabling the WTP to successfully fulfill its mission of safely stabilizing legacy nuclear waste.

12 - MGMT OF RADIOACTIVE AND NON-RADIOACTIVE WASTE↗
DOE OSTI2024

Planar Thermal Hall Effect from Phonons in Cuprates

A surprising “planar” thermal Hall effect, whereby the field is parallel to the current, has recently been observed in a few magnetic insulators; this effect has been attributed to exotic excitations such as Majorana fermions or chiral magnons. Here, we investigate the possibility of a planar thermal Hall effect in three different cuprate materials, in which the conventional thermal Hall conductivity 𝜅 xy (with an out-of-plane field perpendicular to the current) is dominated by either electrons or phonons. Our measurements show that the planar 𝜅 xy from electrons in cuprates is zero, as expected from the absence of a Lorentz force in the planar configuration. By contrast, we observe a sizable planar 𝜅 xy in those samples where the thermal Hall response is due to phonons, even though it should, in principle, be forbidden by the high crystal symmetry. Our findings call for a careful reexamination of the mechanisms responsible for the phonon thermal Hall effect in insulators.

Cuprates↗
DOE OSTI2022

Condition assessment of cable insulation materials in advanced reactor environments

While existing cable insulation materials are sufficient for use in the current reactor fleet, environmental conditions inside some advanced reactors, such as small modular reactors, will be substantially harsher. The work herein was conducted to assess the performance and overall survivability of several high-temperature, radiation resistant insulation polymers in a simulated small modular reactor environment. The materials evaluated under this research include polyether ether ketone, polyimide, and silicone rubber. These polymers were subjected to 1000 h of environmental stress exposure under two different conditions: 1) high temperature (i.e., 250 °C) in atmospheric pressure and 2) high temperature in a low-pressure vacuum (i.e., less than 2 psia). During the environmental exposure process, each insulation was periodically tested using several materials characterization techniques including Fourier transform infrared spectroscopy, oxidation induction time, and oxidation induction temperature. The objective of this testing was to assess and monitor changes that occurred in the thermal and chemical properties of the materials during the environmental exposures. The overall survivability of each insulation was assessed based on these property changes. The results of this research revealed that the polyimide and polyether ether ketone insulations had significantly better thermal and chemical stability than the silicone rubber during both the high-temperature atmospheric and vacuum exposures. Both polyimide and polyether ether ketone experienced minimal reductions in their chemical and thermal properties over the course of 1000 h in the simulated environments. Finally, based on this research, polyimide and polyether ether ketone show promise as potential base materials for small modular reactor cable insulation.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗