Search NASA⌕ Search

SEARCH · Search NASA

Results for “Writing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Depth-Resolved X-Ray Nanoimaging of Coherent and Incoherent Energy Transport in Silicon Carbide

Understanding lattice dynamics is crucial for optimizing the process of creating functional structures, such as laser writing of color-center defects. However, existing structural probes have difficulty measuring structural dynamics with submicrometer depth sensitivity. Here, in this study, a depth-resolved ultrafast X-ray nanodiffraction technique is developed to track the lattice dynamics of silicon carbide (SiC) in three dimensions. Upon laser excitation of an aluminum layer that acts as a heat and strain transducer, a specular Bragg peak of SiC shows an overall increase in the X-ray diffraction intensity rather than a peak shift. The relaxation dynamics of the increased intensity are significantly different when probed on and off the Bragg peak. The fast subnanosecond relaxation probed at the maximum of the Bragg peak is a result of the propagation of a coherent strain wave along the depth direction, while a slow relaxation probed at the wings of the Bragg peak reflects a localized incoherent lattice heating. To further visualize these processes, spatiotemporal maps were obtained by scanning the relative position and delay between the laser pump and X-ray probe beams, which capture the propagation of the strain wave, as well as a stationary structural distortion close to the aluminum/SiC interface. These depth-resolved structural measurements disentangle energy dissipation mechanisms in laser-excited SiC, and they open opportunities for finer control of, for example, the formation of optically addressable defect complexes central to quantum information applications.

X-ray nanodiffraction↗
DOE OSTI2024

Programmable quantum emitter formation in silicon

Abstract Silicon-based quantum emitters are candidates for large-scale qubit integration due to their single-photon emission properties and potential for spin-photon interfaces with long spin coherence times. Here, we demonstrate local writing and erasing of selected light-emitting defects using femtosecond laser pulses in combination with hydrogen-based defect activation and passivation at a single center level. By choosing forming gas (N 2 /H 2 ) during thermal annealing of carbon-implanted silicon, we can select the formation of a series of hydrogen and carbon-related quantum emitters, including T and C i centers while passivating the more common G-centers. The C i center is a telecom S-band emitter with promising optical and spin properties that consists of a single interstitial carbon atom in the silicon lattice. Density functional theory calculations show that the C i center brightness is enhanced by several orders of magnitude in the presence of hydrogen. Fs-laser pulses locally affect the passivation or activation of quantum emitters with hydrogen for programmable formation of selected quantum emitters.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Hierarchically ordered porous transition metal compounds from one-pot type 3D printing approaches

Solution-based soft matter self-assembly (SA) promises unique material structures and properties from approaches including additive manufacturing/three-dimensional (3D) printing. The 3D printing of periodically ordered porous functional inorganic materials through SA unfolding during printing remains a major challenge, however, due to the often vastly different ordering kinetics of separate processes at different length scales. Here, we report a “one-pot” direct ink writing process to produce hierarchically porous transition metal nitrides and precursor oxides from block copolymer (BCP) SA. Heat treatment protocols identified in various environments enable mesostructure retention in the final crystalline materials with periodic lattices on three distinct length scales. Moreover, embedded printing enables the first BCP directed mesoporous non-self-supporting helical oxides and nitrides. Resulting nitrides are superconducting, with record nanoconfinement-induced upper critical fields correlated with BCP molar mass and record surface areas for compound superconductors. Results suggest scalable porous functional inorganic material formation approaches for applications including catalysis, sensing, and microelectronics.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Alignment switching in 3D-printed smectic liquid crystal elastomers

Extrusion-based additive manufacturing has emerged as a powerful platform for designing shape-morphing materials through controlled orientation. However, existing approaches primarily rely on a single mode of flow-induced alignment, limiting orientation programmability. Herein, we present a direct-ink-writing approach for smectic liquid crystal elastics that exploits two distinct alignment modes within a single ink. The smectic ink exhibits shear- and temperature-dependent orientation switching, enabling molecular alignment either perpendicular or parallel to the print direction. Combined rheological, X-ray, and molecular dynamics analyses reveal that this alignment inversion arises from the preservation or collapse of smectic layers under flow. This reversible switching encodes both contractile and elongational actuation within individual filaments, greatly expanding the design freedom of printed liquid crystal elastomers. We demonstrate 2D and 3D structures with diverse programmed shape transformations, highlighting the potential of this platform for adaptive soft actuators and architected functional materials.

Lee, Jin Hyeong [Pusan National University, Busan,↗
DOE OSTI2024

On-demand nanoengineering of in-plane ferroelectric topologies

Hierarchical assemblies of ferroelectric nanodomains, so-called super-domains, can exhibit exotic morphologies that lead to distinct behaviours. Controlling these super-domains reliably is critical for realizing states with desired functional properties. Here we reveal the super-switching mechanism by using a biased atomic force microscopy tip, that is, the switching of the in-plane super-domains, of a model ferroelectric Pb 0.6 Sr 0.4 TiO 3 . We demonstrate that the writing process is dominated by a super-domain nucleation and stabilization process. A complex scanning-probe trajectory enables on-demand formation of intricate centre-divergent, centre-convergent and flux-closure polar structures. Correlative piezoresponse force microscopy and optical spectroscopy confirm the topological nature and tunability of the emergent structures. The precise and versatile nanolithography in a ferroic material and the stability of the generated structures, also validated by phase-field modelling, suggests potential for reliable multi-state nanodevice architectures and, thereby, an alternative route for the creation of tunable topological structures for applications in neuromorphic circuits.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2026

Optical control of integer and fractional Chern insulators

Optical control of topology, particularly in the presence of electron correlations, is an interesting topic with broad scientific and technological impact. Twisted MoTe 2 bilayer (tMoTe 2 ) is a zero-field fractional Chern insulator (FCI), exhibiting the fractionally quantized anomalous Hall effect. As the chirality of the edge states and sign of the Chern number are determined by the underlying ferromagnetic polarization, manipulation of ferromagnetism would realize control of the Chern insulator (CI)/FCI states. Here, in this work, we demonstrate control of ferromagnetic polarization, and thus the CI and FCI states, by circularly polarized optical pumping in tMoTe 2 . At low excitation power, we achieve on-demand preparation of ferromagnetic polarization by optical training, that is, electrically tuning the system from non-ferromagnetic to desirable ferromagnetic states under helicity-selective optical pumping. With increased excitation power, we further realize direct optical switching of ferromagnetic polarization at a temperature far below the Curie temperature. Both optical training and direct switching are most effective near CI and FCI states, which we attribute to a gap-enhanced valley polarization of optically pumped holes. The magnetization can be dynamically switched by modulating the helicity of optical excitation. Spatially resolved measurements further demonstrate optical writing of ferromagnetic, and thus CI (or FCI) domains. Our work realizes precise optical control of a topological quantum many-body system with potential applications in topological spintronics, quantum memories and creation of exotic edge states by programmable patterning of integer and fractionally quantized anomalous Hall domains.

ferromagnetism↗
DOE OSTI2025

3D nanolithography with metalens arrays and spatially adaptive illumination

The growing demand for advanced materials, miniaturized devices and integrated microsystems calls for the reliable fabrication of complex, multiscale, three-dimensional (3D) architectures, a need increasingly addressed through light-based and laser-based processes. However, owing to the field-of-view (FOV) limitations of conventional imaging optics, existing 3D laser nanofabrication techniques face fundamental challenges in throughput, proximity error and stitching defects on the path to scaling. Here, in this study, we present a scalable 3D nanofabrication platform that uses a metalens-generated focal spot array to parallelize two-photon lithography (TPL) beyond centimetre-scale write field areas. Metalenses are ideally suited for producing submicron-scale focal spots for high-throughput nanolithography, as they uniquely feature large numerical apertures (NAs), immersion media compatibility and large-scale manufacturability. We experimentally demonstrate a printing system that uses a 12-cm 2 metalens array to produce more than 120,000 cooperative focal spots, corresponding to a throughput exceeding 10 8 voxels s −1 . By programmatically patterning the focal spot array using a spatial light modulator (SLM), an adaptive parallel printing strategy is developed for precise greyscale linewidth modulation and choreographed printing of semiperiodic and fully aperiodic 3D geometries. We demonstrate parallel printing of replicated microstructures (>50 M microparticles per day), centimetre-scale 3D architectures with feature sizes down to 113 nm, and photonic and mechanical metamaterials. This work demonstrates the potential of 3D nanolithography towards wafer-scale production, showing how TPL could be used at scale for applications in microelectronics, biomedicine, quantum technology and high-energy laser targets.

Materials science↗
DOE OSTI2025

Impact of CuInP 2 S 6 –metal interfaces on the stabilization of polar phases and polarization switching

The multifunctionality of two-dimensional ferroelectric CuInP 2 S 6 (CIPS) arises from the existence of multiple polar phases combined with a high ionic conductivity that facilitates polarization switching in unusual ways. The van der Waals (vdW) layered structure provides ultrathin flakes and ideal interfaces to integrate with other materials for microelectronics and neuromorphic elements. However, device integration necessitates metal contacts to read, write, or transmit signals. In this work, we find that different types of metal–CIPS interfaces strongly impact the stabilization of specific polar phases and the field-induced transitions between the polarization states. Cu electrodes initially suppress the piezoresponse, whereas, at CIPS–Ag interfaces, the electromechanical signal is increased. Under electric fields, the Cu electrodes, Ag electrodes and surrounding CIPS surfaces can show distinct switching behavior as different phases and polarization orientations are stabilized. These findings highlight that metal–CIPS interfaces provide the opportunity to optimize functional material properties.

Ferroelectrics and multiferroics↗
DOE OSTI2026

A scalable superconducting nanowire memory array with row–column addressing

Scalable superconducting memory is required for the development of low-energy superconducting computers and fault-tolerant quantum computers. Conventional superconducting logic-based memory cells possess a large footprint that limits scaling; nanowire-based superconducting memory cells, although more compact, have high error rates, which hinders integration into large arrays. Here we report a 4 × 4 superconducting nanowire memory array that is designed for scalable row–column operations and has a functional density of 2.6 Mbit cm −2 . Each memory cell is based on a nanowire loop consisting of two temperature-dependent superconducting switches and a variable kinetic inductor. The arrays operate at 1.3 K, where we implement and characterize multiflux quanta state storage and destructive read-out. By optimizing the write- and read-pulse sequences, we minimize bit errors and maximize operating margins. We achieve a minimum bit error rate of 10 −5 . Here, we also use circuit-level simulations to understand the memory cell’s dynamics, performance limits and stability under varying pulse amplitudes.

Electrical and electronic engineering↗
DOE OSTI2025

Material extrusion additive manufacturing of wood pulp-reinforced epoxy composites

Direct ink writing (DIW) is an extrusion-based form of 3D-printing that has gained popularity over the last decade. DIW uses thixotropic fluid extrusion to form a particular shape. In order to form stable structures, the rheology of the paste is important to allow for extrusion from the syringe, stability of the growing print, and prevention of unwanted seeping flow during jog moves. In this work, we use wood pulp as a bio-based filler that can provide shear thinning properties to the ink, which produces a stable ink for DIW processing. Additionally, the filler imparts improved mechanical and thermal performance compared to neat resin. The wood pulp provided the shear thinning behavior necessary for DIW printing, and pulp loadings greater than 6 wt%, provided sufficient yield stress so that the composite could self-support during printing. Nanoclay was utilized to further improve ink rheology and appearance to enable larger scale printing. Overall, this work showed successful DIW of an epoxy resin with a sustainable filler improving its stiffness and thermal properties and provides an avenue for further development of bio-based inks for DIW towards various applications.

Lamm, Meghan E. [Oak Ridge National Laboratory (OR↗
DOE OSTI2025

3D printing of architected sulfur cathodes with dual-site atomic catalysts for accelerated polysulfide kinetics and Li-ion transport in high areal-loading lithium–sulfur batteries

The practical deployment of lithium–sulfur batteries (LSBs) is hindered by fundamental limitations in conventional slurry-cast cathodes, including poor sulfur utilization, sluggish ion transport, and low areal capacity, particularly in thick electrodes required for high energy density. To address these challenges, we present direct ink writing (DIW) as an additive manufacturing strategy to fabricate advanced current-collector-free, 3D-printed sulfur cathodes (3DP S@CoNi-DSACs/NC) with hierarchically porous architectures that enhance lithium-ion diffusion, promote electrolyte penetration, and reduce interfacial resistance. The synergistic effects of Co/Ni dual-atom sites accelerate redox kinetics and mitigate polysulfide shuttling. As a result, the optimized 3DP cathode with a sulfur loading of 5.4 mg cm −2 demonstrated excellent rate capability, delivering a high reversible capacity of 1041.4 mAh g −1 at 1C with 85.5% capacity retention after 1000 cycles, significantly outperforming its cast counterpart. Remarkably, even at a higher sulfur loading of 8.1 mg cm −2 , the 3DP cathode maintains outstanding performance, achieving a discharge capacity of 1538.4 mAh g −1 and an areal capacity of 12.5 mAh cm −2 at 0.1C. This study not only demonstrates the functional integration of catalytically active materials into 3D printable sulfur cathode architectures but also offers a scalable and transformative platform for building high-performance LSBs beyond conventional electrode manufacturing methods.

3D electrode↗
DOE OSTI2026

Graphene oxide precursor effects on 3D-printed carbon scaffolds

Manganese oxide (MnO 2 ), an earth-abundant material, is a promising component for energy storage devices, with uses in both pseudocapacitors and batteries. However, high MnO 2 loading often leads to reduced performance due to poor ion diffusion. 3D printing, particularly using the direct ink writing (DIW) technique, offers a solution by enabling the fabrication of electrodes with hierarchical porous structures and open channels that enhance mass transport and ion diffusion. Previous work demonstrated that 3D-printed graphene aerogels with MnO 2 coatings exhibited excellent electrochemical performance, even with thick electrodes, due to their optimized structure. Building on this work, the current study investigates the performance differences between aerogels developed using graphene oxide (GO) and reduced graphene oxide (rGO) as carbon precursors. Both materials were incorporated into thixotropic inks, 3D-printed into lattice structures, and carbonized. Despite expected similarities between the final graphene aerogel, rGO-based aerogels exhibited superior areal capacitance, compared to GO-based aerogels. These differences are attributed to the lower oxygen content and defect density of rGO, which influence its interaction with cellulose viscosifiers in the ink formulation. Brunauer–Emmett–Teller (BET) surface area analysis revealed that rGO aerogels exhibit a larger surface area and mesoporous structure, further enhancing their performance. When coated with MnO 2 , rGO-based aerogels maintained their superior capacitive behavior over GO-based aerogels. This study highlights the effect of carbon precursor on the end performance of graphene aerogels.

Materials science↗
DOE OSTI2024

Transitioning GlideinWMS, a multi domain distributed workload manager, from GSI proxies to tokens and other granular credentials

GlideinWMS is a distributed workload manager that has been used in production for many years to provision resources for experiments like CERN’s CMS, many Neutrino experiments, and the OSG. Its security model was based mainly on GSI (Grid Security Infrastructure), using X.509 certificate proxies and VOMS (Virtual Organization Membership Service) extensions. Even when other credentials, like SSH keys, were used to authenticate with resources, proxies were also added all the time, to establish the identity of the requestor and the associated memberships or privileges. This single credential was used for everything and was, often implicitly, forwarded wherever needed. The addition of identity and access tokens and the phase-out of GSI forced us to reconsider the security model of GlideinWMS, to handle multiple credentials which can differ in type, technology, and functionality. Both identity tokens and access tokens are supported. GSI proxies even if no more mandatory, are still used, together with various JWT (JSON Web Token) based tokens and other certificates. The functionality of the credentials, defined by issuer, audience, and scope, also differ: a credential can allow access to a computing resource, or can protect the GlideinWMS framework from tampering, or can grant read or write access to storage, can provide an identity for accounting or auditing, or can provide a combination of any the formers. Furthermore, the tools in use do not include automatic forwarding and renewal of the new credentials so credential lifetime and renewal requirements became part of the discussion as well. In this paper, we will present how GlideinWMS was able to change its design and code to respond to all these changes.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Involving the new generations in Fermilab endeavors

Since 1984 the Italian groups of the Istituto Nazionale di Fisica Nucleare (INFN) and Italian Universities, collaborating with the DOE laboratory of Fermilab (US) have been running a two-month summer training program for Italian university students. While in the first year the program involved only four physics students of the University of Pisa, in the following years it was extended to engineering students. This extension was very successful and the engineering students have been since then extremely well accepted by the Fermilab Technical, Accelerator, and Scientific Computing Division groups. Over the many years of its existence, this program has proven to be the most effective way to engage new students in Fermilab endeavors. Many students have extended their collaboration with Fermilab with their Master’s Thesis and PhD. Since 2004 the program has been supported in part by DOE in the frame of an exchange agreement with INFN. Over its almost 40 years of history, the program has grown in scope and size and has involved more than 550 Italian students from more than 20 Italian Universities, Several Institutes of Research, including ASI and INAF in Italy, and the ISSNAF Foundation in the US, have provided additional financial support. Since the program does not exclude appropriately selected non-Italian students, a handful of students from European and non-European Universities were also accepted over the years. Each intern is supervised by a Fermilab Mentor responsible for performing the training program. Training programs spanned from Tevatron, CMS, Muon (g-2), Mu2e, and Short Baseline Neutrino Experiments and DUNE design and experimental data analysis, development of particle detectors (silicon trackers, calorimeters, drift chambers, neutrino and dark matter detectors), design of electronic and accelerator components, development of infrastructures and software for exascale data handling, research on superconductive elements and on accelerating cavities, and theory of particle accelerators. Since 2010, within an extended program supported by the Italian Space Agency and the Italian National Institute of Astrophysics, a total of 30 students in physics, astrophysics, and engineering have been hosted for two months in the summer at US space science Research Institutes and laboratories. In 2015 the University of Pisa included these programs within its educational programs. Accordingly, Summer School students are enrolled at the University of Pisa for the duration of the internship and are identified and ensured as such. At the end of the internship, the students are required to write summary reports on their achievements. After positive evaluation by a University Examining Board, interns are acknowledged credits for their Diploma Supplement. The program was canceled in 2020 and 2021 due to the pandemic but restarted successfully in 2022. We believe this program can be taken as a model and easily adopted by interested institutions.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

The Italian Summer Students Program at Fermilab and other US Laboratories: 40 years of education in particle physics and technology

Since 1983 the Italian groups collaborating with Fermilab (US) have been running a 2-month summer training program for Master students. While in the first year the program involved only 4 physics students, in the following years it was extended to engineering students. Many students have extended their collaboration with Fermilab with their Master Thesis and PhD. The program has involved more than 600 Italian students from more than 20 Italian universities. Each intern is supervised by a Fermilab Mentor responsible for the training program. Training programs spanned from Tevatron, CMS, Muon (g-2), Mu2e and SBN (MicroBooNE, Icarus, and SBND) and DUNE design and data analysis, development of particle detectors, design of electronic and accelerator components, development of infrastructures and software for tera-data handling, quantum computing and research on superconductive elements and accelerating cavities. In 2015 the University of Pisa included the program within its own educational programs. Summer Students are enrolled at the University of Pisa for the duration of the internship and at the end of the internship they write summary reports on their achievements. After positive evaluation by a University of Pisa Examining Board, interns are acknowledged 6 ECTS credits for their Diploma Supplement. The program was paused in 2020 and 2021 due to the COVID-19 pandemic, but it resumed in 2022. From 2022 to 2024, a total of 60 students participated in the nine-week training at Fermilab. We are currently organizing the 2025 program. This paper provides an overview of the program, which can serve as a model for other interested laboratories.

Barzi, Emanuela [Ohio State U.]↗
DOE OSTI2025

Reconstruction framework advancements to support streaming for the ePIC detector at the EIC

The ePIC collaboration adopted the JANA2 framework to manage its reconstruction algorithms. This framework has since evolved substantially in response to ePIC’s needs. There have been three main design drivers: integrating cleanly with the Podio-based data models and other layers of the key4hep stack, enabling external configuration of existing components, and supporting timeframe splitting for streaming readout. The result is a unified component model featuring a new declarative interface for specifying inputs, outputs, parameters, services, and resources. This interface enables the user to instantiate, configure, and wire components via an external file. One critical new addition to the component model is a hierarchical decomposition of data boundaries into levels such as Run, Timeframe, PhysicsEvent, and Subevent. Two new component abstractions, Folder and Unfolder, are introduced in order to traverse this hierarchy, e.g. by splitting or merging. The pre-existing components can now operate at different event levels, and JANA2 will automatically construct the corresponding parallel processing topology. This means that a user may write an algorithm once, and configure it at runtime to operate on timeframes or on physics events. Overall, these changes mean that the user requires less knowledge about the framework internals, obtains greater flexibility with configuration, and gains the ability to reuse the existing abstractions in new streaming contexts.

Brei, Nathan [Thomas Jefferson National Accelerato↗
DOE OSTI2025

ROOT RNTuple and EOS: The Next Generation of Event Data I/O

For several years, the ROOT team is developing the new RNTuple I/O subsystem in preparation of the next generation of collider experiments. Both HL-LHC and DUNE are expected to start data taking by the end of this decade. They pose unprecedented challenges to event data I/O in terms of data rates, event sizes, and event complexity. At the same time, the I/O landscape is becoming more diverse. HPC cluster file systems and object stores, NVMe disk cache layers in analysis facilities, and S3 storage on cloud resources are mixing with traditional XRootD-managed spinning disk pools.The ROOT team will finalize a first production version of the RNTuple binary format by the end of 2024. After this point, ROOT will provide backward compatibility for RNTuple data. This contribution provides an overview of the RNTuple feature set, the related R&D activities and the long-term vision for RNTuple. We report on performance, interface design, tooling, robustness, integration with experiment frameworks, and validation results, as well as recent R&D on parallel reading and writing and exploitation of modern hardware and storage systems. We will give an outlook on possible future features after a first production release.Collaboratively, the IT and EP departments at CERN have launched a formal project within the Research and Computing sector to evaluate the novel data format for physics analysis data utilized in LHC experiments and other fields. This part of the project focuses on validating the scalability of the EOS storage backend during the transition from the over 25 years old TTree production format to the newly developed RNTuple format, using both replicated and erasure-coded storage profiles.

Blomer, Jakob [CERN]↗
DOE OSTI2025

Multistate resistance in TaN/(Hf,Zr)O 2 /Ta ferroelectric tunnel junctions

Ferroelectric tunnel junctions (FTJs) utilizing hafnium zirconium oxide (HZO) have emerged as promising non-volatile memory elements for microelectronics, compatible with back end of line (BEOL) complementary–metal–oxide semiconductor fabrication. This study investigates asymmetric electrode TaN/HZO/Ta devices with a 6 nm thick HZO layer as FTJs for multistate resistive memory applications. The individual FTJs exhibit a resistance ratio exceeding 10× when utilized as a binary state device, with pulsing between −1.7 and +1.4 V to set the high resistance state (HRS) and low resistance state (LRS), respectively. Following with reduced write voltage pulses allows the ferroelectric device to operate with a selection of over 32 distinct resistance states (2 5 bits) between the LRS and HRS. This work then explores the stability of the resistance states during write/read pulse cycling, along with the stability of the state after multiple read pulses. Accessing the multibit state shows stability within 50 reads with the binary state remaining stable for more than 4000 reads pulses. With their multistate tunability and versatility, FTJs hold promise as BEOL memory elements for compute-in-memory (CiM) arrays, binary digital memory, or weighted vector matrix multiplication applications with low power consumption during computations.

CMOS↗