Search NASA⌕ Search

SEARCH · Search NASA

Results for “acoustic tones”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Further Development of Rotating Rake Mode Measurement Data Analysis

The Rotating Rake mode measurement system was designed to measure acoustic duct modes generated by a fan stage. After analysis of the measured data, the mode amplitudes and phases were quantified. For low-speed fans within axisymmetric ducts, mode power levels computed from rotating rake measured data would agree with the far-field power levels on a tone by tone basis. However, this agreement required that the sound from the noise sources within the duct propagated outward from the duct exit without reflection at the exit and previous studies suggested conditions could exist where significant reflections could occur. To directly measure the modes propagating in both directions within a duct, a second rake was mounted to the rotating system with an offset in both the axial and the azimuthal directions. The rotating rake data analysis technique was extended to include the data measured by the second rake. The analysis resulted in a set of circumferential mode levels at each of the two rake microphone locations. Radial basis functions were then least-squares fit to this data to obtain the radial mode amplitudes for the modes propagating in both directions within the duct. The fit equations were also modified to allow evanescent mode amplitudes to be computed. This extension of the rotating rake data analysis technique was tested using simulated data, numerical code produced data, and preliminary in-duct measured data.

Dahl, Milo D.↗
NASA NTRS1974

Theoretical studies on tone noise from a ducted fan rotor

The method of computing radiated noise from a ducted rotor due to inflow distortion and turbulence are examined. Analytical investigations include an appropriate description of sources, the cut-off conditions imposed on the modal propagation of the pressure waves in the annular duct, and reflections at the upstream end of the duct. Far field sound pressure levels at blade passing frequency due to acoustic radiation from a small scale low speed fan are computed. Theoretical predictions are in reasonable agreement with experimental measurements.

Rao, C. V. R.↗
NASA NTRS2004

Category 5: Sound Generation in Viscous Problems

Two problems are considered. Problem 1: Aeolian tones, sound generation by flow over cylinders, are relevant to airframe and power plant noise (heat exchanger, power transmission lines and chimneys). The purpose of this problem is to test the ability of a CFD/CAA code to accurately predict sound generation by viscous flows and sound propagation through interactions between acoustic wave & solid wall and between acoustic waves & shear layers. Problem 2: Sound generation by flow over a cavity.Air flows over the cavity shown below with a mean approach flow velocity of 50 m/s. The boundary layer that develops over the flat plate is turbulent with a thickness of 14 mm at the entrance to the cavity. Calculate the power spectra at the center of each cavit wall and the center of the cavity floor. Experimental data will be available for comparison.

Lee, Soogab↗
NASA NTRSDate not supplied

Aeroacoustic Computations of a Transonic Truss-Braced Wing Aircraft: Part 2 – Acoustic Signature and Noise Source Identification

High-fidelity, time-dependent simulations of a Boeing-designed, transonic, truss-braced-wing aircraft in cruise (clean) and landing configurations are leveraged to generate synthetic microphone-phased-array data for airframe noise prediction and assessment. These data sets are used to compute source localization (beamform) maps to determine the location and strength of primary and secondary airframe noise sources associated with this unique configuration. The synthetic phased-array implementation mimics the setup of a flight test. As this study is ongoing, preliminary integrated far-field spectra for the cruise configuration obtained at multiple spatial resolutions revealed significant tonal content that lacked convergence with increased resolution. The origin of several of these tones and their unusual convergence behavior was traced to the larger-than-normal trailing-edge thickness of the “as-tested” cruise model being simulated. Reducing the trailing-edge thickness to more realistic values eliminated most of the tones at low to moderate frequencies and improved spectrum convergence significantly. Applying lessons learned from the cruise simulations, several modifications to the geometry of the landing configuration were made and are described in this work. Results from permeable and solid Ffowcs-Williams and Hawkings surfaces at two different spatial resolutions (coarse and medium) are used to illustrate the major noise sources and determine convergence of the CLEAN integrated noise levels for the entire aircraft as well as major subcomponents. We demonstrate that the low-frequency content of the far-field spectrum is dominated by noise generated from the main landing gear, while the medium- and high-frequency content is dominated by the wing-leading-edge Krueger flaps. Since analysis of the acoustic maps for the landing configuration revealed several clusters of multiple sources along the wing leading edge, “high resolution” processing of the array data was used to distinguish more accurately the locations of sources.

Transonic Truss-Braced Wing↗
NASA NTRS1986

Coherent large-scale structures in high Reynolds number supersonic jet of Mach number 1.4

Large-scale coherent structures are found to exist in fully expanded shock free supersonic jets with Reynolds number 1.6 million and Mach number 1.4. The jet was excited by a weak upstream tone to extract the large-scale structures from the random turbulence. The most preferential excitation Strouhal number is found to be in the vicinity of 0.4, and the dependence of the large-scale structure phase velocity on the excitation Strouhal number shows a similar trend to that found for subsonic acoustically excited jets.

Lepicovsky, J.↗
NASA NTRS2005

Turbofan Noise Reduction Associated With Increased Bypass Nozzle Flow

An advanced 22-in. scale model turbofan, typical of a current-generation aircraft engine design by GE Aircraft Engines, was tested in NASA Glenn Research Center s 9- by 15- Foot Low-Speed Wind Tunnel to explore the far-field acoustic effects of an increased bypass nozzle area at simulated aircraft speeds of takeoff, approach, and landing. The wind-tunnel-scale model consisted of the bypass stage fan, stators, and nacelle (including the fan exit nozzle) of a typical turbofan. This fan-stage test was part of the NASA Glenn Fan Broadband Source Diagnostic Test, second entry, which acquired aeroacoustic results over a range of test conditions. A baseline nozzle was selected, and the nozzle area was chosen for maximum performance at sea-level conditions. Two additional nozzles were also tested--one with a 5.4-percent increase in nozzle area over the baseline nozzle (sized for design point conditions), corresponding to a 5-percent increase in fan weight flow, and another nozzle with a 10.9-percent increase in nozzle area over the baseline nozzle (sized for maximum weight flow at sea-level conditions), corresponding to a 7.5 percent increase in fan weight flow. Measured acoustic benefits with increased nozzle area were very encouraging, showing overall sound power level reductions of 2 dB or more (left graph) while the stage adiabatic efficiency (right graph) and thrust (final graph) actually increased by several percentage points. These noise-reduction benefits were seen to include both rotor-interaction tones and broadband noise, and were evident throughout the range of measured sideline angles.

Woodward, Richard P.↗
NASA NTRS1984

Acoustic measurements of a full-scale rotor with four tip shapes. Volume 2: Appendices C, D, E and F

A full scale helicopter with four different blade tip geometries is tested in a 40- by 80-foot wind tunnel. Performance, loads, and noise are measured. The four tip shapes tested were rectangular, tapered, swept, and swept/tapered. The noise data include measurements of the sound pressure levels in decibels dB, decibels adjusted dBA, and tone-corrected PNdB, for all of the conditions tested. Also included are the detailed measurements, 1/3 octave spectra and time histories for some selected data, and plots of dBA as function of test condition. Some performance measurements are included to aid interpretation of the noise data.

Mosher, M.↗
NASA NTRS1975

Vehicle for civil helicopter ride quality research

A research aircraft for investigating the factors involved in civil helicopter operations was developed for NASA Langley Research Center. The aircraft is a reconfigured 17000 kg (36000 lb) military transport helicopter. The basic aircraft was reconfigured with advanced acoustic treatment, air-conditioning, and a 16-seat airline cabin. During the spring of 1975, the aircraft was flight tested to measure interior environment characteristics - noise and vibration - and was flown on 60 subjective flight missions with over 600 different subjects. Data flights established noise levels somewhat higher than expected, with a pure tone at 1400 Hz and vertical vibration levels between 0.07g and 0.17g. The noise and vibration levels were documented during subjective flight evaluations as being the primary source of discomfort. The aircraft will be utilized to document in detail the impact of various noise and vibration levels on passenger comfort during typical short-haul missions.

Snyder, W. J.↗
NASA NTRS2002

A Tool for Low Noise Procedures Design and Community Noise Impact Assessment: The Rotorcraft Noise Model (RNM)

To improve aircraft noise impact modeling capabilities and to provide a tool to aid in the development of low noise terminal area operations for rotorcraft and tiltrotors, the Rotorcraft Noise Model (RNM) was developed by the NASA Langley Research Center and Wyle Laboratories. RNM is a simulation program that predicts how sound will propagate through the atmosphere and accumulate at receiver locations located on flat ground or varying terrain, for single and multiple vehicle flight operations. At the core of RNM are the vehicle noise sources, input as sound hemispheres. As the vehicle "flies" along its prescribed flight trajectory, the source sound propagation is simulated and accumulated at the receiver locations (single points of interest or multiple grid points) in a systematic time-based manner. These sound signals at the receiver locations may then be analyzed to obtain single event footprints, integrated noise contours, time histories, or numerous other features. RNM may also be used to generate spectral time history data over a ground mesh for the creation of single event sound animation videos. Acoustic properties of the noise source(s) are defined in terms of sound hemispheres that may be obtained from theoretical predictions, wind tunnel experimental results, flight test measurements, or a combination of the three. The sound hemispheres may contain broadband data (source levels as a function of one-third octave band) and pure-tone data (in the form of specific frequency sound pressure levels and phase). A PC executable version of RNM is publicly available and has been adopted by a number of organizations for Environmental Impact Assessment studies of rotorcraft noise. This paper provides a review of the required input data, the theoretical framework of RNM's propagation model and the output results. Code validation results are provided from a NATO helicopter noise flight test as well as a tiltrotor flight test program that used the RNM as a tool to aid in the development of low noise approach profiles.

Conner, David A.↗
NASA NTRS1979

Evaluation of aero commander propeller acoustic data: Taxi operations

The acoustic data from ground tests performed on an Aero Commander propeller driven aircraft are analyzed. An array of microphones flush mounted on the side of the fuselage were used to record data. The propeller blade passage noise during operations at several different taxi speeds is considered and calculations of the magnitude and phase of the blade passage tones, the amplitude stability of the tones, and the spatial phase and coherence of the tones are included. The measured results are compared to theoretical predictions for propeller noise and various evaluations which reveal important details of propeller noise characteristics are presented.

Piersol, A. G.↗
NASA NTRS1979

Tone noise of three supersonic helical tip speed propellers in a wind tunnel

Three eight bladed supersonic helical tip speed propellers were tested in the NASA Lewis Wind Tunnel at through flow Mach numbers of 0.6, 0.7, 0.75, 0.8, and 0.85. Such propellers are being considered as propulsors for a future energy conservative aircraft. The three propellers of equal performance, incorporate different plan forms and different amounts of sweep in order to investigate their noise generation, which could cause a cabin environment problem. The acoustically designed propeller SR-3 had 45 deg of tip sweep and was significantly quieter at Mach 0.8 cruise than the straight bladed propeller, SR-2. An intermediate 30 deg tip sweep propeller, SR-1m exhibited a noise level between the other two. Enhanced pressure-time traces indicated that SR-2 and SR-1m exhibited shock-like pressure traces at Mach-0.8 cruise while the SR-3 did not. Noise trends with varying helical tip Mach number and blade loading were also observed.

Dittmar, J. H.↗
NASA NTRS1977

Effect of inlet disturbances on fan inlet noise during a static test

Measurements of fan rotor inlet noise taken during static test situations are at variance with aircraft engine flight data. In particular, static tests generally yield a significantly higher tone at blade passage frequency than that measured during flight. To explain this discrepancy, the extent of the influence of inlet ground vortices and large-scale inlet turbulence on the forward-radiated fan noise measured at a static test facility was investigated. While such inlet disturbances were generated intentionally in an anechoic test chamber, far-field acoustic measurements and inlet flow-field hot-film mappings of a fan rotor were obtained. Experimental results indicate that the acoustic effect of such disturbances appears to be less severe for supersonic than for subsonic tip speeds. Further, a reverse flow that occurs on the exterior cowl in static test facilities appears to be an additional prime candidate for creating inlet disturbances and causing variance between flight and static acoustic data.

Bekofske, K. L.↗
NASA NTRS1979

Effect of grazing flow on the acoustic impedance of Helmholtz resonators consisting of single and clustered orifices

A semiempirical fluid mechanical model is derived for the acoustic behavior of thin-walled single orifice Helmholtz resonators in a grazing flow environment. The incident and cavity sound fields are connected in terms of an orifice discharge coefficient whose values are determined experimentally using the two-microphone method. Measurements show that at high grazing flow speeds, acoustical resistance is almost linearly proportional to the grazing flow speed and almost independent of incident sound pressure. The corresponding values of reactance are much smaller and tend towards zero. For thicker-walled orifice plates, resistance and reactance were observed to be less sensitive to grazing flow as the ratio of plate thickness to orifice diameter increased. Loud tones were observed to radiate from a single orifice Helmholtz resonator due to interaction between the grazing flow shear layer and the resonator cavity. Measurements showed that the tones radiated at a Strouhal number equal to 0.26. The effects of grazing flow on the impedance of Helmholtz resonators consisting of clusters of orifices was also studied. In general, both resistance and reaction were found to be virtually independent of orifice relative spacing and number. These findings are valid with and without grazing flow.

Hersch, A. S.↗
NASA NTRS1983

Flight effects on fan noise with static and wind tunnel comparisons

A flight test program utilizing a JT15D-1 turbofan engine has been conducted with the objectives of studying flight effects on fan noise and evaluating the simulation effectiveness of both a wind tunnel and a static test configuration that incorporated an inlet control device (ICD). In conjunction with synchronized laser-radar tracking and meteorological profile information, data obtained from a linear array of ground microphones was narrowband-analyzed and ensemble-averaged to yield highly accurate far-field flight acoustic results. Utilizing appropriate corrections, flight, wind tunnel, and static acoustic data were normalized to a static-equivalent, 100-foot radius, lossless reference condition. Data comparisons showed that both the static test with ICD and wind tunnel were generally very effective in simulating flight blade-passage-frequency (BPF) noise levels. However, differences were observed in broadband noise levels and in the details of the multiple-pure-tone harmonics.

Preisser, J. S.↗
NASA NTRS2014

Noise from a Supersonic Round Jet Discharging Into a Duct

In an effort to understand an 'unwanted noise' problem occasionally encountered in ground test facilities, the interaction of a jet flow with a duct is studied in a model scale experiment. While the interaction of subsonic jets was studied earlier, that of supersonic jets is considered in this paper. The effect of the presence of a cylindrical duct in the path of the jet is studied through sound pressure level spectral measurements as well as schlieren flow visualization. When the jet involves screech tones the placement of the duct is found to make only minor effects on the tones themselves as well as on the high frequency noise. However, there is increased energy at low frequencies. The increase in low frequency noise becomes clearer when screech is eliminated from the jet by two small tabs placed at the nozzle exit. It is shown that spectral peaks and increased sound pressure levels occur at frequencies corresponding to the axial acoustic resonance modes of the duct. These peaks persist into the supersonic regime, however, their amplitudes diminish relative to increasing spectral amplitudes at other frequencies with increasing jet Mach number. A wire-mesh screen attached to the end of the duct effectively suppresses such unwanted noise at subsonic as well as supersonic conditions.

Jet Noise↗
NASA NTRS1997

Rotorcraft Noise Model

The Rotorcraft Noise Model (RNM) is an aircraft noise impact modeling computer program being developed for NASA-Langley Research Center which calculates sound levels at receiver positions either on a uniform grid or at specific defined locations. The basic computational model calculates a variety of metria. Acoustic properties of the noise source are defined by two sets of sound pressure hemispheres, each hemisphere being centered on a noise source of the aircraft. One set of sound hemispheres provides the broadband data in the form of one-third octave band sound levels. The other set of sound hemispheres provides narrowband data in the form of pure-tone sound pressure levels and phase. Noise contours on the ground are output graphically or in tabular format, and are suitable for inclusion in Environmental Impact Statements or Environmental Assessments.

Lucas, Michael J.↗
NASA NTRS2012

Acoustic Performance of the GEAE UPS Research Fan in the NASA Glenn 9- by 15-Foot Low-Speed Wind Tunnel

A model advanced turbofan was acoustically tested in the NASA Glenn 9- by 15-Foot Low-Speed Wind Tunnel in 1994. The Universal Propulsion Simulator fan was designed and manufactured by General Electric Aircraft Engines, and included an active core, as well as bypass, flow paths. The fan was tested with several rotors featuring unswept, forward-swept and aft-swept designs of both metal and composite construction. Sideline acoustic data were taken with both hard and acoustically treated walls in the flow passages. The fan was tested within an airflow at a Mach number of 0.20, which is representative of aircraft takeoff/approach conditions. All rotors showed similar aerodynamic performance. However, the composite rotors typically showed higher noise levels than did corresponding metal rotors. Aft and forward rotor sweep showed at most modest reductions of transonic multiple pure tone levels. However, rotor sweep often introduced increased rotor-stator interaction tone levels. Broadband noise was typically higher for the composite rotors and also for the aft-swept metal rotor. Transonic MPT generation was reduced with increasing fan axis angle of attack (AOA); however, higher downstream noise levels did increase with AOA resulting in higher overall Effective Perceived Noise Level.

Woodward, Richard P.↗
NASA NTRS1981

Aerodynamic and acoustic behavior of a YF-12 inlet at static conditions

An aeroacoustic test program to determine the cause of YF-12 inlet noise suppression was performed with a YF-12 aircraft at ground static conditions. Data obtained over a wide range of engine speeds and inlet configurations are reported. Acoustic measurements were made in the far field and aerodynamic and acoustic measurements were made inside the inlet. The J-58 test engine was removed from the aircraft and tested separately with a bellmouth inlet. The far field noise level was significantly lower for the YF-12 inlet than for the bellmouth inlet at engine speeds above 5500 rpm. There was no evidence that noise suppression was caused by flow choking. Multiple pure tones were reduced and the spectral peak near the blade passing frequency disappeared in the region of the spike support struts at engine speeds between 6000 and 6600 rpm.

Bangert, L. H.↗