Results for “adaptive refinement” — Page 20

NASA NTRS1997

On Efficient Parallel Implementation of Moving Body Overset Grid Methods

An investigation into the parallel performance of moving-body overset grid methods will be presented. Parallel versions of the OVERFLOW flow solver, DCF3D domain connectivity software, and SIXDO six-degree-of-freedom routine are coupled with an automatic load balance routine and tested for 3D Navier-Stokes calculations on the IBM SP2. The primary source of parallel inefficiency in moving and problems are the domain connectivity costs with DCF 3D. Although this algorithm constitutes a relatively low fraction of the total solution cost (e.g. 10-20%) in calculations on serial machines, the consequently cause a significant degradation in the overall parallel performance. The paper will highlight some approaches for improving the scalability of DCF3D. The paper will present results of a proposed new load balancing scheme that seeks more equal distribution of the inter-grid boundary points in order to more evenly load balance the donor search costs associated with DCF3D. Some preliminary results will also be given from a new solution-adaption algorithm coupled with OVERFLOW which incorporates overset cartesian grids with various levels of refinement. The measured parallel performance from a descending delta-wing configuration and a generic store-separation from a wing/pylon case will be presented.

Wissink, Andrew M.↗

NASA NTRS2002

Adjoint-Based, Three-Dimensional Error Prediction and Grid Adaptation

Engineering computational fluid dynamics (CFD) analysis and design applications focus on output functions (e.g., lift, drag). Errors in these output functions are generally unknown and conservatively accurate solutions may be computed. Computable error estimates can offer the possibility to minimize computational work for a prescribed error tolerance. Such an estimate can be computed by solving the flow equations and the linear adjoint problem for the functional of interest. The computational mesh can be modified to minimize the uncertainty of a computed error estimate. This robust mesh-adaptation procedure automatically terminates when the simulation is within a user specified error tolerance. This procedure for estimating and adapting to error in a functional is demonstrated for three-dimensional Euler problems. An adaptive mesh procedure that links to a Computer Aided Design (CAD) surface representation is demonstrated for wing, wing-body, and extruded high lift airfoil configurations. The error estimation and adaptation procedure yielded corrected functions that are as accurate as functions calculated on uniformly refined grids with ten times as many grid points.

Park, Michael A.↗

NASA NTRS2006

Unstructured CFD and Noise Prediction Methods for Propulsion Airframe Aeroacoustics

Using unstructured mesh CFD methods for Propulsion Airframe Aeroacoustics (PAA) analysis has the distinct advantage of precise and fast computational mesh generation for complex propulsion and airframe integration arrangements that include engine inlet, exhaust nozzles, pylon, wing, flaps, and flap deployment mechanical parts. However, accurate solution values of shear layer velocity, temperature and turbulence are extremely important for evaluating the usually small noise differentials of potential applications to commercial transport aircraft propulsion integration. This paper describes a set of calibration computations for an isolated separate flow bypass ratio five engine nozzle model and the same nozzle system with a pylon. These configurations have measured data along with prior CFD solutions and noise predictions using a proven structured mesh method, which can be used for comparison to the unstructured mesh solutions obtained in this investigation. This numerical investigation utilized the TetrUSS system that includes a Navier-Stokes solver, the associated unstructured mesh generation tools, post-processing utilities, plus some recently added enhancements to the system. New features necessary for this study include the addition of two equation turbulence models to the USM3D code, an h-refinement utility to enhance mesh density in the shear mixing region, and a flow adaptive mesh redistribution method. In addition, a computational procedure was developed to optimize both solution accuracy and mesh economy. Noise predictions were completed using an unstructured mesh version of the JeT3D code.

Pao, S. Paul↗

NASA NTRS2015

NASA's Space Launch System Program Update

Hardware and software for the world's most powerful launch vehicle for exploration is being welded, assembled, and tested today in high bays, clean rooms and test stands across the United States. NASA's Space Launch System (SLS) continued to make significant progress in 2014 with more planned for 2015, including firing tests of both main propulsion elements and the program Critical Design Review (CDR). Developed with the goals of safety, affordability, and sustainability, SLS will still deliver unmatched capability for human and robotic exploration. The initial Block 1 configuration will deliver more than 70 metric tons of payload to low Earth orbit (LEO). The evolved Block 2 design will deliver some 130 metric tons to LEO. Both designs offer enormous opportunity and flexibility for larger payloads, simplifying payload design as well as ground and on-orbit operations, shortening interplanetary transit times, and decreasing overall mission risk. Over the past year, every vehicle element has manufactured or tested hardware. An RS-25 liquid propellant engine was hotfire-tested at NASA's Stennis Space Center, Miss. for the first time since 2009 exercising and validating the new engine controller, the renovated A-1 test stand, and the test teams. Four RS-25s will power the SLS core stage. A qualification five-segment solid rocket motor incorporating several design, material, and process changes was scheduled to be test-fired in March at the prime contractor's facility in Utah. The booster also successfully completed its Critical Design Review (CDR) validating the planned design. All six major manufacturing tools for the core stage are in place at the Michoud Assembly Facility in Louisiana, and have been used to build numerous pieces of confidence, qualification, and even flight hardware, including barrel sections, domes and rings used to assemble the world's largest rocket stage. SLS Systems Engineering accomplished several key tasks including vehicle avionics software and hardware build and testing, scale model acoustic and base heating tests. Construction of the Interim Cryogenic Propulsion Stage (ICPS) began. Advanced development provided a look into the future of SLS. Shell buckling knockdown factor testing refined decades-old design margins that added thousands of pounds to rocket payloads. Adaptive manufacturing and structured light scanning development promised to cut the cost and time associated with manufacturing and testing. This paper will provide an overview of the progress made over the past year and provide a glimpse of 2015 milestones and beyond on the way to the first launch in 2018.

May, Todd↗

NASA NTRS2015

NASA's Space Launch System Program Update

Hardware and software for the world's most powerful launch vehicle for exploration is being welded, assembled, and tested today in high bays, clean rooms and test stands across the United States. NASA's Space Launch System (SLS) continued to make significant progress in 2014 with more planned for 2015, including firing tests of both main propulsion elements and the program Critical Design Review (CDR). Developed with the goals of safety, affordability, and sustainability, SLS will still deliver unmatched capability for human and robotic exploration. The initial Block 1 configuration will deliver more than 70 metric tons of payload to low Earth orbit (LEO). The evolved Block 2 design will deliver some 130 metric tons to LEO. Both designs offer enormous opportunity and flexibility for larger payloads, simplifying payload design as well as ground and on-orbit operations, shortening interplanetary transit times, and decreasing overall mission risk. Over the past year, every vehicle element has manufactured or tested hardware. An RS-25 liquid propellant engine was hotfire-tested at NASA's Stennis Space Center, Miss. for the first time since 2009 exercising and validating the new engine controller, the renovated A-1 test stand, and the test teams. Four RS-25s will power the SLS core stage. A qualification five-segment solid rocket motor incorporating several design, material, and process changes was scheduled to be test-fired in March at the prime contractor's facility in Utah. The booster also successfully completed its Critical Design Review (CDR) validating the planned design. All six major manufacturing tools for the core stage are in place at the Michoud Assembly Facility in Louisiana, and have been used to build numerous pieces of confidence, qualification, and even flight hardware, including barrel sections, domes and rings used to assemble the world's largest rocket stage. SLS Systems Engineering accomplished several key tasks including vehicle avionics software and hardware build and testing, scale model acoustic and base heating tests. Construction of the Interim Cryogenic Propulsion Stage (ICPS) began. Advanced development provided a look into the future of SLS. Shell buckling knockdown factor testing refined decades-old design margins that added thousands of pounds to rocket payloads. Adaptive manufacturing and structured light scanning development promised to cut the cost and time associated with manufacturing and testing. This paper will provide an overview of the progress made over the past year and provide a glimpse of 2015 milestones and beyond on the way to the first launch in 2018.

May, Todd↗

NASA NTRS1989

Embedded adaptation for time dependent real fluid/gas flows

An embedded adaptation algorithm is used to illustrate applications and requirements for Navier-Stokes and nonequilibrium unsteady two-dimensional flow fields. Both grid refinement and equation modification are included for unstructured distributions of quadrilateral cells. Multiple refinement parameters for distinct physical phenomena serve to monitor the evolving nonuniform field and to recognize flow features in isolated and overlapping subdomains. Examples from subsonic, hypersonic, internal, and external fields show substantial advantages for the adaptive approach.

Baron, Judson R.↗

NASA NTRS2014

Assume-Guarantee Abstraction Refinement Meets Hybrid Systems

Compositional verification techniques in the assume- guarantee style have been successfully applied to transition systems to efficiently reduce the search space by leveraging the compositional nature of the systems under consideration. We adapt these techniques to the domain of hybrid systems with affine dynamics. To build assumptions we introduce an abstraction based on location merging. We integrate the assume-guarantee style analysis with automatic abstraction refinement. We have implemented our approach in the symbolic hybrid model checker SpaceEx. The evaluation shows its practical potential. To the best of our knowledge, this is the first work combining assume-guarantee reasoning with automatic abstraction-refinement in the context of hybrid automata.

Reliability↗

NASA NTRS2013

Photogrammetry of a Hypersonic Inflatable Aerodynamic Decelerator

In 2012, two large-scale models of a Hypersonic Inflatable Aerodynamic decelerator were tested in the National Full-Scale Aerodynamic Complex at NASA Ames Research Center. One of the objectives of this test was to measure model deflections under aerodynamic loading that approximated expected flight conditions. The measurements were acquired using stereo photogrammetry. Four pairs of stereo cameras were mounted inside the NFAC test section, each imaging a particular section of the HIAD. The views were then stitched together post-test to create a surface deformation profile. The data from the photogram- metry system will largely be used for comparisons to and refinement of Fluid Structure Interaction models. This paper describes how a commercial photogrammetry system was adapted to make the measurements and presents some preliminary results.

aerodynamic brakes↗

NASA NTRSDate not supplied

Transcriptomic Changes in Seedlings from Seeds Exposed to Simulated Space Radiation

Outside the protection of Earth’s magnetic field, living organisms are constantly exposed to space radiation that consists of energetic protons and other heavier charged particles. With the goal of manned Mars exploration, the production of fresh crop during long duration space missions can be beneficial for meeting astronauts’ nutritional and psychological needs. In our study, we not only evaluated plant/fruit morphometrics and edible fresh mass, but also analyzed transcriptomic changes in seedlings from seeds of three plant species (Arabidopsis, mizuna, and tomato) exposed to simulated Galactic Cosmic Rays(GCR) and solar particle events(SPE). The radiation experiments were performed in the NASA Space Radiation Laboratory (NSRL) facility at Brookhaven National Lab (BNL). 10-day Arabidopsis seedlings were exposed acutely (~240 cGy/hr) to simulated GCR scenarios of combined ions including protons, helium, oxygen, titanium, and/or iron ions at 40 or 80 cGy. Seeds of Arabidopsis, mizuna, and tomato were exposed to 40 or 80 cGy simulated GCR (dry seeds) or SPE (imbibed seeds) at lower dose rates(20-26 cGy/hr). Seedlings from control and irradiated seeds were then collected in RNAlater at similar growth stages with true leaves emerged. Total RNA was isolated and analyzed via Illumina whole transcriptome sequencing technology. Plant species-specific bioinformatics revealed transcriptional biomarkers and signaling pathways induced by simulated space radiation that were found to be dose, dose-rate, and species dependent. DNA damage response, stress signaling, and metabolic pathways are among the most significant changes. These data highlight some critical insights on the mechanisms of how plants respond and adapt to the space radiation environment and provide a molecular basis for crop selection and refinement in deep space exploration.

Anirudha Dixit↗

NASA NTRSDate not supplied

Enabling Metric-Based Mesh Adaptation for Advanced Compressible Flow Simulations Using US3D

This work presents a metric-based mesh adaptation capability added to the flow solver US3D that is used to improve the accuracy of atmospheric entry simulations. Flow past an entry vehicle in free-flight is usually unsteady and characterized by anisotropic flow features like a strong bow shock and small-scale isotropic flow features like turbulent eddies in the wake. The results presented in this paper demonstrate that we are currently able to iteratively apply metric-based mesh adaptation to improve the solution accuracy by simultaneously targeting isotropic and anisotropic flow features. A simplified workflow of running CFD simulations for entry vehicles is presented where we start off with a coarse initial mesh to compute a first approximation of the flow. This coarse mesh is then iteratively refined using the newly developed metric to improve the resolution of the CFD computation. Furthermore, we demonstrate that we are able to adapt large mesh sizes in a timely fashion which allows us to start thinking about applying this adaptive framework to unsteady atmospheric entry CFD simulations.

Mesh adaptation↗

NASA NTRSDate not supplied

Anisotropic Goal-Based Mesh Adaptation Metric Clarification and Development

Adaptive unstructured mesh techniques have a limited, but growing impact on production analysis workflows to control discretization error for reliable simulation results. Multiple independent implementations of flow solvers, anisotropic metric construction methods, and anisotropic mesh adaptation mechanics have matured. Goal-based metrics target estimated error in output functions, such as lift and drag, through the guidance of an adjoint solution. A unification of goal-based anisotropic metrics is presented for steady viscous flows, which is an active area of research. These goal-based metrics drive robust and efficient anisotropic mesh adaptation for the calculation of output functions. The super-convergent functional output error behavior of stabilized finite-element methods is exploited without a formal proof, and evidence of super-convergence is shown in numerical experiments. Mesh adapted drag and lift outputs for two simple bodies in compressible viscous flow show convergence of error to less than a single drag count. Asymptotic behavior established for relatively coarse meshes shows the efficiency of this goal-based metric when compared to solution interpolation error control and expert-guided meshing. Anisotropic mesh adaptation techniques are applied to a transport aircraft in a high-lift configuration where variation between approaches decreases with mesh refinement, but asymptotic behavior is not observed with available resources.

goal-based↗

NASA NTRS2016

Revisiting the Microlensing Event OGLE 2012-BLG-0026: A Solar Mass Star with Two Cold Giant Planets

Two cold gas giant planets orbiting a G-type main-sequence star in the galactic disk were previously discovered in the high-magnification microlensing event OGLE-2012-BLG-0026. Here, we present revised host star flux measurements and a refined model for the two-planet system using additional light curve data. We performed high angular resolution adaptive optics imaging with the Keck and Subaru telescopes at two epochs while the source star was still amplified. We detected the lens flux, H = 16.39 +/- 0.08. The lens, a disk star, is brighter than predicted from the modeling in the original study. We revisited the light curve modeling using additional photometric data from the B and C telescope in New Zealand and CTIO 1.3 m H-band light curve. We then include the Keck and Subaru adaptive optic observation constraints. The system is composed of an approximately 4-9 Gyr lens star of M(sub lens) = 1.06 +/- 0.05 solar mass at a distance of D(sub lens) = 4.0 +/- 0.3 kpc, orbited by two giant planets of 0.145 +/- 0.008 M(sub Jup) and 0.86 +/- 0.06 M(sub Jup), with projected separations of 4.0 +/- 0.5 au and 4.8 +/- 0.7 au, respectively. Because the lens is brighter than the source star by 16 +/- 8% in H, with no other blend within one arcsec, it will be possible to estimate its metallicity using subsequent IR spectroscopy with 8-10 m class telescopes. By adding a constraint on the metallicity it will be possible to refine the age of the system.

high-magnification microlensing event OGLE-2012-BL↗

NASA NTRSDate not supplied

Comparing Unstructured Adaptive Mesh Solutions for the High Lift Common Research Model Airfoil

Discretization error is a common source of uncertainty in Computational Fluid Dynamics (CFD) analyses. Traditional means of controlling discretization error through fixed-mesh refinement studies has proven to be difficult particularly when modeling complex geometries and flow fields. One reason for this is that mesh generation in today’s production CFD workflow is often a labor intensive process that is heavily dependent on user judgment. Unstructured mesh adaptation is known to be an efficient way to control discretization errors in CFD. Adaptive methods replace user based decision making with automated processes that optimize a mesh to reduce discretization error. This paper compares the application of multiple solution adaptive techniques in combination with multiple flow solvers to solve for the flow field about a 2D airfoil section of the NASA High-Lift Common Research Model (HL-CRM). By driving the adaptive mesh processes to a similar level of mesh convergence, the ability to achieve consistent results between multiple adaptive techniques and flow solvers is demonstrated. Mesh convergence for the various adaptive mesh approaches is compared identifying potential areas for improvement and providing mesh generation guidance for future workshops.

mesh adaptation high-lift 2D airfoil↗

NASA NTRSDate not supplied

Comparing Unstructured Adaptive Mesh Solutions for the High Lift Common Research Model Airfoil

Discretization error is a common source of uncertainty in Computational Fluid Dynamics (CFD) analyses. Traditional means of controlling discretization error through fixed-mesh refinement studies has proven to be difficult particularly when modeling complex geometries and flow fields. One reason for this is that mesh generation in today’s production CFD workflow is often a labor intensive process that is heavily dependent on user judgment. Unstructured mesh adaptation is known to be an efficient way to control discretization errors in CFD. Adaptive methods replace user based decision making with automated processes that optimize a mesh to reduce discretization error. This paper compares the application of multiple solution adaptive techniques in combination with multiple flow solvers to solve for the flow field about a 2D airfoil section of the NASA High-Lift Common Research Model (HL-CRM). By driving the adaptive mesh processes to a similar level of mesh convergence, the ability to achieve consistent results between multiple adaptive techniques and flow solvers is demonstrated. Mesh convergence for the various adaptive mesh approaches is compared identifying potential areas for improvement and providing mesh generation guidance for future workshops.

mesh adaptation↗

NASA NTRS1983

Evaluation of truncation error and adaptive grid generation for the transonic full potential flow calculations

The effects of truncation error on the numerical solution of transonic flows using the full potential equation are studied. The effects of adapting grid point distributions to various solution aspects including shock waves is also discussed. A conclusion is that a rapid change of grid spacing is damaging to the accuracy of the flow solution. Therefore, in a solution adaptive grid application an optimal grid is obtained as a tradeoff between the amount of grid refinement and the rate of grid stretching.

Nakamura, S.↗

NASA NTRS2015

Application of the Refined Zigzag Theory to the Modeling of Delaminations in Laminated Composites

The Refined Zigzag Theory is applied to the modeling of delaminations in laminated composites. The commonly used cohesive zone approach is adapted for use within a continuum mechanics model, and then used to predict the onset and propagation of delamination in five cross-ply composite beams. The resin-rich area between individual composite plies is modeled explicitly using thin, discrete layers with isotropic material properties. A damage model is applied to these resin-rich layers to enable tracking of delamination propagation. The displacement jump across the damaged interfacial resin layer is captured using the zigzag function of the Refined Zigzag Theory. The overall model predicts the initiation of delamination to within 8% compared to experimental results and the load drop after propagation is represented accurately.

Groh, Rainer M. J.↗

NASA NTRSDate not supplied

Improving the Use of Surface-Sensitive Radiances in the GMAO Hybrid-4DEnVar System

The planetary boundary layer (PBL) was designated as an incubation-class targeted observable (TO) in the 2018 Decadal Survey. As no single instrument source will provide enough information to constrain the global PBL, the assimilation of a wide range of observations in data assimilation (DA) systems will play a critical role, and GMAO has put in efforts to enhance surface-sensitive radiance assimilation. Although a vast number of microwave radiance observations are used in the GEOS global DA system, very few surface-sensitive radiances are currently used over land due to large uncertainty of land surface emissivity in the CRTM as well as cloud detection issue. Dynamically varying emissivity is retrieved from observations of window channels in the GEOS system for non-scattering FOVs and applied to sounding channel assimilation. Moreover, the original radiance bias correction is found not to work well over land, and shows drifting bias when the original emissivity sensitivity bias predictor with a dynamically varying emissivity retrieval is used. Hence, the radiance bias correction has been modified, and the quality control procedure has been adapted accordingly. Cycled experiment results show improvement in the temperature forecast at lower model levels; further refinement of this system continues.

Yanqiu Zhu↗

NASA NTRSDate not supplied

Incorporating ADAPT-VQE with a Sparse Wavefunction Circuit Simulator to Find Compact Quantum Circuits for Chemical Applications

We implemented the ADAPT-VQE algorithm into our recent classical sparse wavefunction circuit simulator to demonstrate that classical resources can (1) efficiently find a physically motivated compact wavefunction ansatz for further refinement on near-term quantum hardware and (2) benchmark expected results of VQE-based algorithms once the quantum hardware is available to study large-scale applications. In particular, we study the role of the ADAPT-VQE operator pool, molecular basis set selection, and variations such as TETRIS-ADAPT-VQE on the performance of our classical circuit simulator. This work demonstrates the promise of using classical resources to generate highly accurate wavefunctions that can be prepared on quantum hardware to initiate other quantum algorithms such as phase estimation. Our approach harnesses the power of high-performance computing resources with the more limited available quantum computers to map a path toward quantum advantage for electronic structure calculations in chemistry and materials science.

Quantum Computing↗