Search NASA⌕ Search

SEARCH · Search NASA

Results for “difference in differences”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Electronic structure, magnetic correlations, and superconducting pairing in the reduced Ruddlesden-Popper bilayer La 3 Ni 2 O 6 under pressure: Different role of d 3 z 2 - r 2 orbital compared with La 3 Ni 2 O 7

The recent discovery of superconductivity in bilayer La 3 Ni 2 O 7 (327-LNO) under pressure stimulated much interest in layered nickelates. However, superconductivity was not found in another bilayer nickelate system, La 3 Ni 2 O 6 (326-LNO), even under pressure. To understand the similarities and differences between 326-LNO and 327-LNO, using density functional theory and the random phase approximation (RPA), we systematically investigate 326-LNO under pressure. The large crystal-field splitting between the e g orbitals caused by the missing apical oxygen moves the d 3z 2 -r 2 orbital farther away from the Fermi level, implying that the d 3z 2 -r 2 orbital plays a less important role in 326-LNO than in 327-LNO. This also results in a smaller bandwidth for the d x 2 -y 2 orbital and a reduced energy gap for the bonding-antibonding splitting of the d 3z 2 -r 2 orbital in 326-LNO, as compared to 327-LNO. Moreover, the in-plane hybridization between the d x 2 -y 2 and d 3z 2 -r 2 orbitals is found to be small in 326-LNO, while it is much stronger in 327-LNO. Furthermore, the low-spin ferromagnetic state is found to be the likely ground state in 326-LNO under high pressure. The weak interlayer coupling suggests that s ± -wave pairing is unlikely in 326-LNO. The robust in-plane ferromagnetic coupling also suggests that d-wave superconductivity, which is usually caused by antiferromagnetic fluctuations of the d x 2 -y 2 orbital, is also unlikely in 326-LNO. These conclusions are supported by our many-body RPA calculations of the pairing behavior. Additionally, contrasting with the cuprates, for the bilayer cuprate HgBa 2 CaCu 2 O 6 , we find a strong self-doping effect of the d x 2 -y 2 orbital under pressure, with the charge of Cu being reduced by approximately 0.13 electrons from 0 GPa to 25 GPa. In contrast, we do not observe such a change in the electronic density in 326-LNO under pressure, establishing another important difference between the nickelates and the cuprates.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Comparative study of He 6 β -decay based on different similarity-renormalization-group evolved chiral interactions

We report on a study of the Gamow-Teller matrix element contributing to ${}^6$He $\beta$-decay with similarity renormalization group (SRG) versions of momentum- and configuration-space two-nucleon interactions. These interactions are derived from two different formulations of chiral effective field theory ($\chi$EFT) -- without and with the explicit inclusion of $\Delta$-isobars. We consider evolution parameters $\Lambda_{\rm SRG}$ in the range between 1.2 and 2.0 fm$^{-1}$ and, for the $\Delta$-less case, also the unevolved (bare) interaction. The axial current contains one- and two-body terms, consistently derived at tree level (no loops) in the two distinct $\chi$EFT formulations we have adopted here. The ${}^6$He and ${}^6$Li ground-state wave functions are obtained from hyperspherical-harmonics (HH) solutions of the nuclear many-body problem. In $A\,$=$\,6$ systems, the HH method is limited at present to treat only two-body interactions and non-SRG evolved currents. Our results exhibit a significant dependence on $\Lambda_{\text{SRG}}$ of the contributions associated with two-body currents, suggesting that a consistent SRG-evolution of these is needed in order to obtain reliable estimates. We also show that the contributions from one-pion-exchange currents depend strongly on the model (chiral) interactions and on the momentum- or configuration-space cutoffs used to regularize them. These results might prove helpful in clarifying the origin of the sign difference recently found in No-Core-Shell-Model and Quantum Monte Carlo calculations of the ${}^6$He Gamow-Teller matrix element.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Information content of the differences in the charge radii of mirror nuclei

Differences in the charge radii of mirror nuclei have been recently suggested to contain information on the slope of the symmetry energy L. To test this hypothesis, we perform statistical correlation analysis using quantified energy density functionals that are consistent with our previous knowledge on global nuclear observables such as binding energies and charge radii. We conclude that the difference in charge radii between a mirror pair, $ΔR$$^{mir}_{ch}$, is an inferior isovector indicator compared to other observables, such at the neutron skin or electric dipole polarizability α D . In particular, this quantity correlates poorly with both the neutron skin and L. Here, we demonstrate that $ΔR$$^{mir}_{ch}$ is influenced by pairing correlations in the presence of low-lying proton continuum in the proton-rich mirror-partner nucleus. Considering the large theoretical uncertainties on $ΔR$$^{mir}_{ch}$, we conclude that the precise data on mirror charge radii cannot provide a stringent constraint on L.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Exploring the growth index γ L : Insights from different CMB dataset combinations and approaches

In this study we investigate the growth index γ L , which characterizes the growth of linear matter perturbations, while analysing different cosmological datasets. We compare the approaches implemented by two different patches of the cosmological solver : and __. In our analysis we uncover a deviation of the growth index from its expected Λ CDM value of 0.55 when utilizing the Planck dataset, both in the case and in the __ case, but in opposite directions. This deviation is accompanied by a change in the direction of correlations with derived cosmological parameters. However, the incorporation of cosmic microwave background lensing data helps reconcile γ L with its Λ -cold dark matter value in both cases. Conversely, the alternative ground-based telescopes Atacama Cosmology Telescope and South Pole Telescope consistently yield growth index values in agreement with γ L = 0.55 . We conclude that the presence of the A lens problem in the Planck dataset contributes to the observed deviations, underscoring the importance of additional datasets in resolving these discrepancies. Published by the American Physical Society 2024

Astronomy & Astrophysics↗
DOE OSTI2023

Characterizing different motility-induced regimes in active matter with machine learning and noise

Here we examine motility-induced phase separation (MIPS) in two-dimensional run-and-tumble disk systems using both machine learning and noise fluctuation analysis. Our measures suggest that within the MIPS state there are several distinct regimes as a function of density and run time, so that systems with MIPS transitions exhibit an active fluid, an active crystal, and a critical regime. The different regimes can be detected by combining an order parameter extracted from principal component analysis with a cluster stability measurement. The principal component-derived order parameter is maximized in the critical regime, remains low in the active fluid, and has an intermediate value in the active crystal regime. We demonstrate that machine learning can better capture dynamical properties of the MIPS regimes compared to more standard structural measures such as the maximum cluster size. The different regimes can also be characterized via changes in the noise power of the fluctuations in the average speed. In the critical regime, the noise power passes through a maximum and has a broad spectrum with a 1/f 1.6 signature, similar to the noise observed near depinning transitions or for solids undergoing plastic deformation.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Evaluating Energy Differences on a Quantum Computer with Robust Phase Estimation

Here, we adapt the robust phase estimation algorithm to the evaluation of energy differences between two eigenstates using a quantum computer. This approach does not require controlled unitaries between auxiliary and system registers or even a single auxiliary qubit. As a proof of concept, we calculate the energies of the ground state and low-lying electronic excitations of a hydrogen molecule in a minimal basis on a cloud quantum computer. The denominative robustness of our approach is then quantified in terms of a high tolerance to coherent errors in the state preparation and measurement. Conceptually, we note that all quantum phase estimation algorithms ultimately evaluate eigenvalue differences.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Different bonding type along each crystallographic axis: Computational study of poly($\textit{p}$-phenylene terephthalamide)

Poly($\textit{p}$-phenylene terephthalamide) (PPTA) exhibits van der Waals (vdW) bonding along its $\textit{a}$ axis, hydrogen bonding along its $\textit{b}$ axis, and covalent bonding along its $\textit{c}$ axis. In this work, we explore the structural and mechanical properties of PPTA using density functional theory with various functionals including LDA, PBE, PBE+rVV10L, SCAN, and SCAN+rVV10, compared with available experiments. The hierarchy of nonempirical semilocal functionals LDA, PBE, and SCAN (not fitted to any multicenter bonded system) includes differing amounts of intermediate-range vdW interaction. rVV10 is the long-range vdW correction. (rVV10L differs from rVV10 only in the value of a range parameter.) Among the tested functionals, SCAN shows the best performance for the lattice parameters of PPTA along the two crystal directions involving vdW or hydrogen-bond interaction. The equilibrium lattice constants obtained by SCAN and PBE+rVV10L are closest to experimental data, while SCAN+rVV10 slightly overbinds the system. We study the mechanical response of PPTA by applying strain along three lattice directions. Due to the inclusion of vdW interaction, SCAN, PBE+rVV10L, and SCAN+rVV10 all exhibit correct bonding strain-energy curves. On the contrary, PBE strongly underestimates the vdW interaction needed to resist uniaxial stretching along the $\textit{a}$ axis. The Young's modulus and yield strength of PPTA are computed and compared with previous results. The experimental values are much smaller than the computed ones, mainly due to the fact that the PPTA fiber samples used for measurements are mechanically weaker than the perfect molecular crystals considered in the simulations. Interestingly, when a compressive uniaxial stress of 25 Kbar is applied along the $\textit{b}$ axis, a structural phase transition, in which the hydrogen bonds reform along one diagonal of the $\textit{ab}$ rectangle, is predicted by SCAN.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Analysis and Comparison of Different Metrics of DC-DC Converters to Determine Fuel Cell Stack Architectures in Heavy Duty Fuel Cell Vehicle Applications

This paper presents a comparative study of the DC-DC converters used in heavy-duty fuel cell electric vehicles for different input fuel cell stack configurations and voltages in terms of various important metrics including efficiency, cost, weight and power density. Contrary to conventional use of an interleaved boost topology, the analysis presented in this paper demonstrates that improved converter metrics can be achieved for an interleaved buck topology that uses a different input fuel cell stack. An insight to the optimal choice of number of interleaved phases for each metric is also presented. Results presented in the tables and plots convey the findings.

Mukherjee, Subho↗
DOE OSTI2021

Systematic Operating Temperature Differences Between Al-BSF, PERC, and PERT-With-Optimized-Rear-Reflector Solar Mini-Modules Due to Rear Reflectance

Reflecting sub-bandgap light from photovoltaic modules has the potential to improve lifetime energy generation of fielded systems by reducing operating temperature. In this article, the temperature of fielded aluminum back-surface field (Al-BSF) and passivated emitter and rear contact (PERC) mini-modules was monitored every 5 minutes for 75 days along with corresponding meteorological data. Additionally, passivated emitter rear totally diffused (PERT) mini-modules with high-performance sub-bandgap rear reflectors were tested and compared to the state-of-the-art industrial modules. These reflectors consisted of a >300-nm-thick silicon dioxide nanoparticle film with a low refractive index. The impact of reflectance on measured operating temperature was isolated with a previously developed thermal model and quantified as the reflectance-induced median temperature difference between each tested module at representative outdoor conditions (1000 W m -2 , 25 degrees C ambient temperature, and 1.43 m s -1 wind speed). We found that, because of their reflectance differences, PERC modules ran systematically cooler than Al-BSF modules by 1.0 degrees C, whereas the PERT-with-optimized-rear-reflector systematically operated 1.4 degrees C cooler than the Al-BSF module and 0.4 degrees C than the PERC module. We also found that the rear reflector provided the greatest temperature benefit during periods of highest irradiance.

14 SOLAR ENERGY↗
DOE OSTI2022

Differently Structured Fabry-Perot Interferometers for Gas Pressure Monitoring

In this study, we present an experimental comparison of gas pressure sensors based on differently structured extrinsic Fabry-Pérot interferometers (FPIs). Different fabrication techniques were adopted to foster the practical realization of these sensors. A novel photonic crystal fiber (PCF) based FPI with an angle cleaved end face that enables gas to easily flow in and out of the cavity while also avoiding the mixed signal from the cascaded structure is also presented. We measured helium gas pressure from 0.1 MPa (atmospheric pressure) to 5 MPa at room temperature and obtained a gas pressure sensitivity coefficient of 0.5±0.01 nm/MPa. Furthermore, the gas pressure sensitivities are numerically analyzed to validate the experimental results.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Differences in c-Si Solar Cell Metallization and Susceptibility to Series Resistance Degradation

In this case study, we investigate a degradation mode occurring at the cell level in fielded multi-Si modules. Affected cells in the module show a progressive, series-resistance-related power degradation observed in module- and cell-level IV curves along with EL and PL imaging at the module, cell, and cell core sample scale. SEM and elemental analysis via EDS reveal a difference in the oxides in the silver paste used in screen printing of the finger contacts. This suggests that the cells were screen printed with different silver paste compositions and possibly firing conditions. One of these combinations leads to degradation of the contact at the interface between the cell and contact finger, causing severe series resistance across the cell that continues to progress over time.

acetic acid↗
DOE OSTI2025

Quantum Approximate Optimization Algorithm on Different Qubit Systems

Solving optimization problems is critical across many research domains, but the high dimensionality of parameter spaces often poses significant challenges. The Quantum Approximate Optimization Algorithm (QAOA) has emerged as a promising approach for accelerating optimization in the Noisy Intermediate-Scale Quantum (NISQ) era by leveraging both classical and quantum computational resources. However, its performance can vary depending on the underlying quantum hardware architecture. In this work, we evaluate the performance of QAOA on different quantum hardware platforms, specifically, superconducting transmon qubits and trapped-ion qubits, targetting real-world optimization problems formulated as fully connected Quadratic Unconstrained Binary Optimization (QUBO) instances. We evaluate both the solution quality and time-to-solution using dense QUBO matrices. Furthermore, we show that large-scale problems, such as a 100-bit QUBO instance, can be effectively tackled by integrating quantum computing with high-performance computing (HPC) resources. This study provides practical insights into the strengths and limitations of different qubit technologies and advances the application of quantum computing in solving real-world optimization problems.

Kim, Seongmin [ORNL] (ORCID:0000000159063004)↗
DOE OSTI2024

Effect of different grain boundary diffusion alloys on magnetic properties of Dy-free sintered NdFeB magnet

Dy-free sintered magnets were fabricated by blending Neo powder with different grain boundary diffusion alloy powders. Cu, CeAl and CeAlCu have a negative effect on H cj of magnets, while PrAlCu and AlCuGa have a positive effect. The PrAlCu-added magnet achieves the best magnetic properties among all magnets with the additions of different diffusion alloys. With increasing PrAlCu from 0-10 wt.%, H cj of the magnets gradually increases from the original 14.5 kOe to 19.2 kOe. The magnet with 7.5 wt.% PrAlCu obtains a H cj of 18 kOe and (BH) max of 39.1 MGOe. It is found that Pr and Cu in PrAlCu alloy is mainly distributed at grain boundary and triple junctions, leading to a reduced coupling among grains, thus an enhanced H cj . Here, the grain boundary engineering by adding an appropriate alloy is an effective method to improve H cj of Dy-free NdFeB magnets.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Bacterial community dynamics explain carbon mineralization and assimilation in soils of different land-use history

Soil dwelling microorganisms are key players in the terrestrial carbon cycle, driving both the degradation and stabilization of soil organic matter. Bacterial community structure and function vary with respect to land use; yet the ecological drivers of this variation remain poorly described and difficult to predict. For this work, we conducted a multi-substrate DNA-stable isotope probing experiment across cropland, old-field, and forest habitats to link carbon mineralization dynamics with the dynamics of bacterial growth and carbon assimilation. We tracked the movement of 13 C derived from five distinct carbon sources as it was assimilated into bacterial DNA over time. We show that carbon mineralization, community composition, and carbon assimilation dynamics all differed with respect to land use. We also show that microbial community dynamics affect carbon assimilation dynamics and are associated with soil DNA content. Soil DNA yield is easy to measure and may be useful in predicting microbial community dynamics linked to soil carbon cycling. Soil dwelling microorganisms are key players in the terrestrial carbon cycle, driving both the degradation and stabilization of soil organic matter. Microbial communities vary with respect to land use, but we still have an incomplete understanding of how variation in community structure links to variation in community function. DNA stable isotope probing (DNA-SIP) is a high-resolution method that can identify specific microbial taxa that assimilate carbon in situ. We conducted a large-scale multi-substrate DNA-SIP experiment to explore differences in bacterial activity across land-use regimes. We show that microbial community dynamics vary with land use, that these dynamics are linked to soil carbon cycling, and that they are associated with easily measured soil properties.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Media matters! Alterations in the loading and release of Histoplasma capsulatum extracellular vesicles in response to different nutritional milieus

Histoplasma capsulatum is a dimorphic fungus that most frequently causes pneumonia, but can also disseminate and proliferate in diverse tissues. H. capsulatum has a complex secretion system that mediates the release of macromolecule-degrading enzymes and virulence factors. The formation and release of extracellular vesicles (EVs) are an important mechanism for non-conventional secretion in both ascomycetes and basidiomycetes. H. capsulatum EVs contain diverse proteins associated with virulence and are immunologically active. Despite the growing knowledge of EVs from H. capsulatum and other pathogenic fungi, the extent that changes in the environment impact the sorting of organic molecules in EVs has not been investigated. In our research, we cultivated H. capsulatum with distinct culture media to investigate the potential plasticity in EV loading in response to differences in nutrition. Our findings reveal that nutrition plays an important role in EV loading and formation, which may translate into differences in biological activities of these fungi in various fluids and tissues.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Effects on the Ocular Surface from Reading on Different Smartphone Screens: A Prospective Randomized Controlled Study

The purpose of this study was to investigate the influence of smartphone reading on the ocular surface and to compare the various effects of different screens and light conditions on the ocular surface. One hundred nineteen volunteers were randomly divided into: light + organic light‐emitting diode (OLED), light + electronic ink (eINK), dark + OLED, and dark + eINK. Ocular surface examinations, including noninvasive break‐up time (NIBUT), noninvasive keratograph tear meniscus height (NIKTMH), ocular redness, fluorescein break‐up time (FBUT), corneal fluorescein staining, meibomian gland assessment, Schirmer I Test, and blinking frequency, were performed before and after a reading task. Symptoms were evaluated using the Ocular Surface Disease Index (OSDI) and Computer Vision Syndrome Questionnaire (CVS‐Q). NIBUT and FBUT were decreased statistically significantly after participants read on an OLED screen for 2 hours compared with the baseline in light and dark environments, whereas no statistically significant decrease was observed on an eINK screen. NIKTMH was statistically significantly decreased after reading on an OLED screen in light and dark settings, and the eINK screen had a lesser effect on NIKTMH. An obvious increase in the ocular redness, OSDI and CVS‐Q scores was observed after reading on an OLED screen, whereas the eINK screen had a lesser effect on these indicators. Blink rate increased gradually in OLED subgroups during the reading task, whereas no statistically significant difference was observed in the eINK subgroups. Our research suggested that reading on an OLED screen can cause ocular surface disorder and obvious subjective discomfort, whereas reading on an eINK screen can minimize ocular surface disorder in both dark and light environments.

Yuan, Kelan↗
DOE OSTI2024

Photosynthetic responses of switchgrass to light and CO 2 under different precipitation treatments

Switchgrass ( Panicum virgatum L .) is a prominent bioenergy crop with robust resilience to environmental stresses. However, our knowledge regarding how precipitation changes affect switchgrass photosynthesis and its responses to light and CO 2 remains limited. To address this knowledge gap, we conducted a field precipitation experiment with five different treatments, including −50%, −33%, 0%, +33%, and +50% of ambient precipitation. To determine the responses of leaf photosynthesis to CO 2 concentration and light, we measured leaf net photosynthesis of switchgrass under different CO 2 concentrations and light levels in 2020 and 2021 for each of the five precipitation treatments. We first evaluated four light and CO 2 response models (i.e., rectangular hyperbola model, nonrectangular hyperbola model, exponential model, and the modified rectangular hyperbola model) using the measurements in the ambient precipitation treatment. Based on the fitting criteria, we selected the nonrectangular hyperbola model as the optimal model and applied it to all precipitation treatments, and estimated model parameters. Overall, the model fit field measurements well for the light and CO 2 response curves. Precipitation change did not influence the maximum net photosynthetic rate ( P max ) but influenced other model parameters including quantum yield ( α ), convexity ( θ ), dark respiration ( Rd ), light compensation point ( LCP ), and saturated light point ( LSP ). Specifically, the mean P max of five precipitation treatments was 17.6 μmol CO 2 m −2 s −1 , and the ambient treatment tended to have a higher P max . The +33% treatment had the highest α , and the ambient treatment had lower θ and LCP , higher Rd , and relatively lower LSP . Furthermore, precipitation significantly influenced all model parameters of CO 2 response. The ambient treatment had the highest P max , largest α , and lowest θ , R d , and CO 2 compensation point LCP . Overall, this study improved our understanding of how switchgrass leaf photosynthesis responds to diverse environmental factors, providing valuable insights for accurately modeling switchgrass ecophysiology and productivity.

09 BIOMASS FUELS↗
DOE OSTI2021

Spectroscopy outperforms leaf trait relationships for predicting photosynthetic capacity across different forest types

Leaf trait relationships are widely used to predict ecosystem function in Terrestrial Biosphere Models (TBMs), in which leaf maximum carboxylation capacity (V c,max ), an important trait for modelling photosynthesis, can be inferred from other easier- to-measure traits. However, whether trait-V c,max relationships are robust across different forest types remains unclear. Here we used measurements of leaf traits, including one morphological trait (leaf mass per area), three biochemical traits (leaf water content, area-based leaf nitrogen content, and leaf chlorophyll content), one physiological trait (V c,max ), as well as leaf reflectance spectra, and explored their relationships within and across three contrasting forest types in China. We found weak and forest type-specific relationships between V c,max and the four morphological and biochemical traits (R 2 ≤ 0.15), indicated by significantly changing slopes and intercepts across forest types. In contrast, reflectance spectroscopy effectively collapsed the differences in the trait-V c,max relationships across three forest biomes into a single robust model for V c,max (R 2 = 0.77), and also accurately estimated the four traits (R 2 = 0.75-0.94). Furthermore, these findings challenge the traditional use of empirical trait-V c,max relationships in TBMs for estimating terrestrial plant photosynthesis, but also highlight spectroscopy as an efficient alternative for characterizing V c,max and multi-trait variability, with critical insights into ecosystem modeling and functional trait ecology.

54 ENVIRONMENTAL SCIENCES↗