Search NASA⌕ Search

SEARCH · Search NASA

Results for “diffuse”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Performance of high-area-ratio annular dump diffuser using suction-stabilized-vortex flow control

A short annular dump diffuser having a geometry conductive to formation of suction stabilized toroidal vortices in the region of abrupt area change was tested. The overall diffuser area ratio was 4.0 and the length to inlet height ratio was 2.0. Performance data were obtained at near ambient temperature and pressure for inlet Mach numbers of 0.18 and 0.30 with suction rates ranging from 0 to 18 percent of total inlet mass flowrate. Results show that the exit velocity profile could be readily biased toward either wall by adjustment of inner and outer wall suction rates. Symmetric exit velocity profiles were inherently unstable with a tendency to revert to a hub or tip bias. Diffuser effectiveness was increased from about 38 percent without suction to over 85 percent at a total suction rate of 10 to 12 percent. At the same time diffuser total pressure loss was reduced from 3.1 percent to 1.1 percent at an inlet Mach number of 0.3.

Juhasz, A. J.↗

Measurement of insulation integrity of IUE camera tube facsimiles by partial discharges method and diffusion of gases through various silicone rubbers

Several dummy tubes imitating the IUE Camera System design were encapsulated with Solithane 2, Conathane EN-11, Green and Black Hysols and SMRD 432. Various flaws were purposefully placed in some of these. Partial discharge testing in vacuum under direct voltage conditions was carried once a week for 12 weeks, 15 kv dc being applied during normal working hours for 40 hours duration per week. None of the units showed much damage during this time judging by the P.D. energy histograms. A more complete mathematical presentation is given on diffusion and permeation than previously. Measurements of diffusion constants for various silicone rubbers are carried out by the Time-Lag method and compared to other determinations in the literature. Calculations of the time required for diffusion through a thick wall are demonstrated in the long time approximation and for dimensions pertaining to void and wall sizes of a delamination problem in the LANDSAT-C vidicon tubes. An actual delaminated LANDSAT-C tube and some facsimiles are immersed in vacuum for long periods and tested for catastrophic breakdown due to diffusion of gas, by application of high voltage.

Bever, R. S.↗

Variations in eddy diffusion and associated transport processes

Variation in the eddy diffusion coefficient constitutes a momentum source. This variation near the turbopause affects both the composition and the wind and temperature fields of the thermosphere. Two types of calculations are carried out, for horizontal winds considered self-consistently in a three-dimensional dynamic model and horizontal winds artificially suppressed to simulate a one-dimensional model. Momentum transfer associated with variations in eddy diffusion coefficients represents the source function in the analysis presented. It is shown that for long-term variations in the thermosphere, the compositional dependence on variations in eddy diffusion coefficients can be entirely different in one and three dimensional models with horizontal winds included. Horizontal winds can greatly reduce the effects of eddy diffusion in general and the ratio between He and O amplitudes in particular.

Mayr, H. G.↗

An investigation of impurity redistribution in diffused layer on /n+/-p silicon solar cells parameters

Recent calculations by Wang et al. (1974) have shown that the short-circuit current for silicon solar cells is sensitive to the impurity distribution in the diffused and base region. In the present work, these theoretical results were verified by experimentally investigating the impurity profile and sheet resistance of the diffused layers of (n+)-p silicon solar cells fabricated by normal diffusion processes and at subsequently various drive-in times. Impurity profiles of the n+ diffused layer, measured by differential Hall and resistivity technique, resemble the erfc distribution. The junction depth is larger as drive-in time increases. Measured short-circuit current is in agreement with calculated ones. Open-circuit voltage is independent of drive-in times, and its calculated values are consistent with capacitance-voltage measurements.

Wang, E. Y.↗

Consequences of using nonlinear particle trajectories to compute spatial diffusion coefficients

In a study of cosmic ray propagation in interstellar and interplanetary space, a perturbed orbit resonant scattering theory for pitch angle diffusion in a slab model of magnetostatic turbulence is slightly generalized and used to compute the diffusion coefficient for spatial propagation parallel to the mean magnetic field. This diffusion coefficient has been useful for describing the solar modulation of the galactic cosmic rays, and for explaining the diffusive phase in solar flares in which the initial anisotropy of the particle distribution decays to isotropy.

Goldstein, M. L.↗

Elevated-temperature flow strength, creep resistance and diffusion welding characteristics of Ti-gAl-2Nb-1Ta-0.8Mo

A study of the flow strength, creep resistance and diffusion welding characteristics of the titanium alloy Ti-6Al-2Nb-1Ta-0.8Mo was conducted. Two mill-processed forms of this alloy were examined. The forged material was essentially processed above the beta transus while the rolled form was subjected to considerable work below the beta transus. Between 1150 and 1250 K, the forged material was stronger and more creep resistant than the rolled alloy. Both forms exhibit superplastic characteristics in this temperature range. Strain measurements during diffusion welding experiments at 1200 K reveal that weld interfaces have no measurable effect on the overall creep deformation. Significant deformation appears to be necessary to produce a quality diffusion weld between superplastic materials. A 'soft' interlayer inserted between faying surfaces would seemingly allow manufacture of quality diffusion welds with little overall deformation.

Whittenberger, J. D.↗

Comments on the origins of the diffuse interstellar bands

Most work in recent years on the unidentified diffuse interstellar bands has been concentrated on the hypothesis that they are produced by some process in solid grains. We review that hypothesis and the arguments which support it, and find that diffuse band formation by certain classes of molecules should not yet be ruled out. Since several relevant observations have been made in the last four years, the observational data on the bands are reviewed. It would appear that these data are as consistent with molecular origins for the bands as with grain origins. Types of molecular transitions which give rise to 'diffuse' bands are described. These transitions can occur in relatively simple molecules composed of cosmically abundant elements and can produce broad, unresolvable profiles without destroying the molecule. New observations are suggested which could produce decisive evidence with which to determine whether the diffuse bands originate in grains, molecules, or both.

Smith, W. H.↗

Effect of microstructure on Na/+/ diffusion in beta alumina

The effect of microstructural features, such as grain size and orientation, on sodium ion diffusion in polycrystalline beta alumina is investigated; the ionic solid is suitable for use in high-energy and power density batteries. Two types of hot-pressed polycrystalline samples are studied, one with grains highly oriented in the direction normal to the pressing direction, the other with significantly less preferred orientation normal to the pressing direction. Results of the experimental assessments indicate that grain size and diffusion path tortuosity have little effect on diffusion kinetics, while grain boundary type and grain aspect ratio are important factors in determining the diffusion rate.

Sarian, S.↗

Effects of particle drift on cosmic ray transport. II - Analytical solution to the modulation problem with no latitudinal diffusion

An analytical solution to a model of the modulation of galactic cosmic rays in the presence of particle drifts is presented and discussed. The solution assumes an energy-independent radial diffusion coefficient proportional to distance and no latitudinal diffusion, and includes energy-independent particle drift velocities similar to those expected in a Parker spiral magnetic field with an equatorial current sheet. The solutions clearly demonstrate the large effects of drifts on the modulated cosmic-ray intensity. For values of the radial diffusion coefficient and particle drift velocity which are plausible for 1-GV-rigidity protons, the logarithmic radial gradient in the inner solar system is reduced by more than a factor of 5 over the value calculated in the absence of drifts. It is found that even for much smaller values of particle drift velocity and radial diffusion coefficient, such as might be expected for protons with energies of the order of 10 MeV, the effects of the drifts can be substantial.

Isenberg, P. A.↗

The effect of nonlinear diffusive heat transport in a simple climate model

The effects of nonlinear diffusive heat transport in North's (1975) model is reexamined. By inserting the nonlinearity into the original energy balance equation rather than the spectrally transformed linear algebraic equations, and including one more mode in the spectral expansion, it is found that nonlinear diffusion does give a significantly different sensitivity for states near the current climate. For linear diffusion, an increase of 0.1% of the solar constant from the present value is sufficient to melt all the ice on the earth, whereas an increase of about five times as large is required for nonlinear diffusion. This difference in sensitivity shows the importance of dynamical modeling in simple climate models.

Lin, C. A.↗

Partially averaged field approach to cosmic ray diffusion

A new nonlinear technique is used to derive the kinetic equation for particles interacting with turbulent fluctuations. Difficulties associated with quasi-linear theory are avoided. The new method evaluates the effects of the fluctuations along particle orbits which themselves include the effects of a statistically averaged subset of the possible configuration of the turbulence. As an illustration, the pitch-angle diffusion coefficient is calculated for particles interacting with 'slab model' magnetic turbulence, i.e., magnetic fluctuations linearly polarized transverse to a mean magnetic field. The pitch-angle diffusion coefficient is determined in the vicinity of 90-deg pitch angles where quasi-linear theory breaks down. The spatial diffusion coefficient parallel to a mean magnetic field is evaluated by use of the calculated pitch-angle diffusion coefficient. It is suggested that the partially averaged field method is not limited to small amplitude fluctuating fields and hence is not a perturbation theory.

Jones, F. C.↗

Nonneutral and quasi-neutral diffusion of weakly ionized multiconstituent plasma

A theory is developed for quasi-neutral and nonneutral ambipolar diffusion in a weakly ionized multiconstituent plasma. Magnetic field effects are disregarded. The effects of negative ions and various positive and negative ion diffusion coefficients are identified. It is found that the presence of negative ions leads to enhanced electron diffusion and a retarded diffusion of positive ions. In some cases electrons may be forcibly propelled from the area of perturbations in ionic concentrations. The ambipolar electric field is observed to cause negative ions to flow in a countergradient fashion where the gradient is small. Electrons tend toward a more homogeneous spatial distribution in the nonneutral case than in the quasi-neutral case.

Hill, R. J.↗

Design and subscale tests of a diffuser system for a Mach 4 scramjet test facility

A fixed-geometry diffuser system was designed for use in Mach 4 free-jet tests of a hydrogen-burning modular scramjet engine. The scramjet engine has a rectangular cross section that blocks up to 33 percent of the existing tunnel nozzle exit area and swept leading edges of the scramjet produce an asymmetric downward flow that sharply increases when the scramjet inlet unstarts. Effects of these conditions on the operation of the diffuser system are not accurately predictable. An experimental investigation has therefore been conducted in unheated air using a subscale model of the tunnel-scramjet-diffuser system to substantiate the design. Test results showed that the preliminary design had to be modified to obtain an acceptable configuration of the nozzle exit, test cabin, and diffuser that would provide shock-free flow at the scramjet inlet for simulated Mach 4 flight at altitudes from 16,764 to 20,422 meters.

Andrews, E. H., Jr.↗

Infrared colors and the diffuse interstellar bands

Broad-band infrared photometric measurements have been gathered for 105 stars which exhibit diffuse interstellar bands in their spectra. All normal stars obey a single reddening law, and a value of R equal to 3.08 + or - 0.15 is derived. This value is consistent with other recent determinations of R. The diffuse band indicators, the central depth of the 4430-A feature and the equivalent widths of the 5780-A and 6284-A features, show as large a scatter with the infrared color excesses as they do with E(B - V). No single-valued relation between the color excesses and the diffuse band strengths appears to exist. This casts doubt on whether dust grains which produce the visual and infrared extinctions are the carriers for the diffuse interstellar features.

Sneden, C.↗

Geomagnetic field fluctuations at synchronous orbit. II - Radial diffusion

Power spectra of geomagnetic-field variations measured at synchronous equatorial altitude (geomagnetic shell parameter about 6.6) in the magnetosphere are used to calculate the time dependence of the radial diffusion coefficient for particles in the radiation belts. The diffusion coefficients calculated are mainly applicable for relativistic electrons. The magnitudes of the derived diffusion coefficients using data only from local day observations are consistent with those reported from analyses of most particle observations and thus are slightly larger than those derived from magnetic sudden commencements. They are consistent with the diffusion coefficients calculated from power spectra of ground-based geomagnetic data measured near L = 4.

Lanzerotti, L. J.↗

Performance of a vortex-controlled diffuser in an annular swirl-can combustor at inlet Mach numbers up to 0.53

A short, annular dump diffuser with suction stabilized vortices in the region of abrupt area change was tested with a full scale, annular swirl can combustor. The prediffuser area ratio was 1.4. Performance data were obtained for both isothermal and burning conditions at inlet temperatures of 589 to 895 K and pressures of 0.5 to 1.0 MPa for a range of diffuser inlet Mach numbers from 0.25 to 0.53. Suction rates were 0 to 20 percent of the total diffuser mass flow rate. Diffuser effectiveness increased from 47 percent without suction to approximately 80 percent for a total suction rate of 14 percent. Combustor total pressure loss for the same total suction rate was reduced from 6.8 percent without suction to 4.0 percent at an inlet Mach number of 0.40.

Smith, J. M.↗

Interdiffusion and intrinsic diffusion in the NiAl /delta/ phase of the Al-Ni system

Interdiffusion coefficients at 950 to 1150 C and the ratio of intrinsic diffusion coefficients at 1100 C were measured as functions of composition in the NiAl (delta) phase of the Al-Ni system, using a vapor-solid technique. Diffusivity values were also obtained for the Ni3Al (epsilon) and Ni (Al) solid solution (zeta) phases from 950 to 1150 C. The interdiffusion coefficient in NiAl (delta) varies several orders of magnitude over the delta phase field with a deep minimum in the diffusivity-composition curve at 48 to 49 at% Al. The ratio of intrinsic diffusion coefficients DNi/DAl, in the delta phase also varies with composition from a value of 3 to 3.5 below 50 at% Al to 0.1 or less above 50 at% Al.

Shankar, S.↗

Further observational support for the lossy radial diffusion model of the inner Jovian magnetosphere

A mathematical model describing radial diffusion, with violation of the third adiabatic invariant and with local losses, is applied to the Pioneer 10 and 11 observations of omnidirectional integral intensities of electrons with energy exceeding 21 MeV. Local losses outside L = 3 are much stronger than synchrotron losses but weaker than the losses one would expect for strong pitch angle diffusion. If radial diffusion is driven by ionospheric winds, as was suggested by Brice and McDonough (1973), it is found that the theoretical solution which best fits the data requires that the radial diffusion coefficient equals 3 x 10 to the -9th L-cubed/s and the lifetime against local losses is approximately a few million seconds.

Goertz, C. K.↗