Search NASA⌕ Search

SEARCH · Search NASA

Results for “ether”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of PCEs with different structures on hydration and properties of cementitious materials with low water-to-binder ratio

Polycarboxylate ethers (PCEs) with different structures and densities of anchor groups in the backbone were synthesized and characterized. The surface tension of their solutions, their adsorption on cementitious particles and zeta potential of cement-silica fume pastes with PCEs were measured. Their effects on hydration and properties of cement-silica fume paste with low water-to-binder ratio were examined. Results indicated that the adsorption kinetics of theses PCEs on cementitious particles are fitted the pseudo-second-order model. The introduction of long silane chain on PCE decreased its electrostatic adsorption, while PCE was adsorbed onto the surface of particles via both chemical and electrostatic adsorption, when silicon hydroxyl is directly connected to its backbone. In the presence of PCE with higher adsorbed amount, pastes exhibited lower yield stress and higher flowability, and higher strength at 7 d and 28 d. The low plastic viscosity, autogenous and drying shrinkage were related to the low surface tension of PCE solution.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Physical and chemical effects of isopropanol exchange in cement-based materials

Drying cement-based materials is a necessary step to characterize the microstructure by microscopy, adsorption, or mercury intrusion. The isopropanol (IPA) exchange method is commonly used to replace the pore solution prior to drying, as it reduces the capillary pressure and thereby helps to preserve the microstructure of the hydrated cementitious materials. However, some physical and chemical effects of IPA on hydration products have been reported. These effects cannot be completely avoided, but can be reduced by shortening the exchange duration, in particular for effects on ettringite. This study carried out experiments with different exchange durations and IPA removal techniques to address research gaps in the literature. For 1-mm cubes of cement paste with IPA diffusion coefficient of 1 × 10{sup −11} m{sup 2}/s, the compared exchange durations are 5 min, 15 min (value from the literature), 40 min (when the mixture at the sample center achieves 95% of the drop in surface tension from water to IPA), 80 min (when the IPA/water mixture at the sample center reaches an azeotrope), 5 h (when over 99% IPA is replaced at the sample center), and 24 h (prolonged exchange). After IPA exchange, samples were either directly dried at 40 °C with flushing N{sub 2} or washed by diethyl ether prior to N{sub 2} drying. Even though the exchange duration of 40 and 80 min, in theory, can reduce the damage from capillary pressure, the nitrogen adsorption results do not show any advantage in preventing microstructural alteration. The 5-h exchange provided results similar to the 24-h exchange, but the latter induced slightly more serious chemical effects resulting from the longer contact of IPA with hydration products. In addition, the compared IPA removal techniques do not show significant differences. Therefore, this study suggests using small samples (~1 mm) for microstructural studies following IPA exchange for a period corresponding to the time when 99% of the water (mole fraction) at the sample center is replaced.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Formulation of low clinker blended cements and concrete with enhanced fresh and hardened properties

Blended cements appear as the most promising way to massively produce cements with reduced environmental footprints. However, considering the generally lower early mechanical performance of highly blended cements, chemical admixtures are increasingly relied upon to increase early strength. However, in many cases this can negatively impact other properties as rheology and durability. This paper proposes an approach to formulate low clinker cements and concrete using moderate alkali activation or gypsum to enhance early and long-term compressive strength, without inducing excessive alkali-silica reaction (ASR) expansion. It examines blended cements containing burnt oil shale along with limestone and fly ash or slag as supplementary cementitious materials. It optimizes the combination of polycarboxylate ether (PCE) superplasticizers with the strength enhancers. Along with the use of Ca(NO{sub 3}){sub 2} to drive PCE adsorption, this provides good rheology control, increased early and long-term compressive strength, as well as acceptable ASR expansion in cements with only 50% clinker.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Evaluation of chromatographic resins for high efficacy separation of radium from chemical analogues

The separation of Radium (Ra) from interfering chemical analogues is of major importance for both the accurate measurement of Ra-226 in environmental samples and the preparation of radium targets destined for medical isotope production. The adsorption behavior of Ra, Barium (Ba), and Strontium (Sr) was investigated on multiple crown-ether-based proprietary extraction chromatographic resins developed by TrisKem Int. Among these, the TK101 resin, characterized by a novel room-temperature ionic liquid (RTIL) dual extractant–solvent system, demonstrated enhanced affinity and selectivity, particularly at low acid concentrations, achieving a D w of 3477 ± 73 for Ra in 0.04 M HNO₃, whereas the maximum Ra D w obtained with the traditional Sr resin in 8 M HNO 3 was only 12.33 ± 0.4. In 0.04 M HNO 3 , a Ra distribution ratio (D w ) of 776 was achieved within 1 min, indicating rapid uptake kinetics. The adsorption capacities were estimated at 19.6 ± 0.1 mg/g for Ba and 12.0 ± 0.2 mg/g for Sr. However, competing alkali metals significantly reduced alkaline earth metal uptake, indicating that the TK101 resin is best suited for radium purification following a preconcentration step to minimize matrix effects in high salinity samples. Dynamic column studies confirmed the strong chromatographic performance of the TK101 resin, with no significant Ba or Sr breakthrough in the Ra fraction and a Ra recovery of 87 ± 2.8%. These results demonstrate the potential of the TK101 resin for selective radium separation in analytical and radiochemical applications.

and nuclear chemistry↗
DOE OSTI2024

Investigating the potential of a higher reactivity fuel to achieve faster heat-up of aftertreatment systems

Shortening the aftertreatment system heat-up period will be crucial to meet upcoming emissions regulations, which mandate significant reductions in tail-pipe emissions for on-road heavy-duty vehicles. This work studies the impact of increasing fuel reactivity on the combustion of post injections during the expansion stroke. The work demonstrates an operating strategy using a blend of di-butyl ether (a potential low-carbon biofuel component) and #2 diesel that achieves higher exhaust enthalpy, while maintaining similar engine-out emissions (NOx and combustion efficiency) in comparison to the baseline #2 diesel fuel (cetane number 41). On average, a 12% increase in exhaust enthalpy was observed for the blend (cetane number 60) relative to the baseline fuel. The ability to operate the higher reactivity fuel at a more retarded post-injection timing, where combustion with #2 diesel was found to be more unstable, and less complete was key to achieving higher exhaust enthalpy. However, a small fuel penalty (3%–5%) was also associated with the higher reactivity fuel with this operating strategy. The formation of fuel lean regions, due to the long ignition delays at late injection conditions, was predicted to be the leading contributor to the increased emissions of products of partial combustion. Here, chemical kinetic simulations using surrogates for the fuels used in the experiments, demonstrated the ability of a higher cetane fuel to outperform the baseline fuel under fuel lean conditions with equivalence ratios less than 0.7.

09 BIOMASS FUELS↗
DOE OSTI2023

Class-based separations of mixed solid–liquid systems with condensable solvent washing and extraction: The dilemma of pizza box recycling

As primary feedstocks deplete across the world, raw material extraction becomes increasingly expensive. Awareness of the environmental impact of primary extraction has motivated the development of energy- and reagent-efficient methods for material reuse. This work confronts an emblematic challenge of modern recycling: the soiled pizza box. While the fibers constituting corrugated cardboard are generally recyclable, pizza contaminants such as sauces and oils complicate their reuse, resulting in municipal prohibitions on the recycling of used pizza boxes in cardboard recycling streams and a representative of 275 kg/year per US household of food waste that is directed to landfill. This challenge is common to many materials, and engineering strategies must be developed to tackle complex/mixed feedstocks. To address the mixed composition of the pizza box (and similar materials), an environmentally benign, non-toxic organic solvent is applied to remove and fractionate components from mixed materials. The solvent employed in this process, dimethyl ether (DME), is a condensable hygroscopic gas, which facilitates its removal and recovery for reuse. Further, the results of this study indicate that 1) DME is capable of solubilizing and extracting components from soiled cardboard and other materials, (resulting in cardboard drier than new/unused cardboard) facilitating its recycling, and 2) the DME-soluble components of the system phase separate into aqueous and fatty acid/oil fractions (potentially ~27.5 kg/year per US household). Condensable solvent-driven washing and extraction enable the efficient separation of multiple intermediate product streams, suggesting a pathway to enable technology development necessary for achieving clean production in a circular economy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Spontaneous sodium ion storage behaviors of reduced graphene oxide anodes exceeding 100% Coulombic efficiency by modulated ion solvation

Rechargeable batteries are essential energy storage devices that power portable devices and electrical vehicles throughout the world. In general, it is thought that the electrochemical performance of rechargeable batteries is mostly determined by the electrodes within them and that the electrolyte plays a relatively passive role. However, ion transport and storage can be greatly influenced by the electrolyte solution structure, specifically, ion solvation within the bulk and ion desolvation across the electrode/electrolyte interfaces. Herein, we studied the role of the electrolyte as an active component of electrochemical energy storage devices. We found that with an appropriate electrolyte formulation, ion storage in disordered carbonaceous anode materials can occur spontaneously without externally supplied electrical energy. Reduced graphene oxide (RGO) in an ether-based electrolyte demonstrates ‘spontaneous' ion storage behaviors of adsorbing and inserting the solvated ions utilizing facilitated permeability and wettability of RGO, which results in Coulombic efficiency of ~145% due to additional charging capacity of ~180 mAh g -1 during electrochemical processes. The unexpected spontaneous ion storage behavior was extensively investigated using a combination of electrochemical analyses and diagnostics, advanced characterizations, and computational simulation. In conclusion, we believe the spontaneous ion storage behavior offers a new way to further improve the energy efficiency of practical rechargeable batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Enhancing durability of polymer electrolyte membrane using cation size selective agents

Radical species generated during proton exchange membrane fuel cell operation considerably limit the achievable durability, particularly for heavy-duty vehicle applications. A promising solution to the problem is the incorporation of radical scavenger additives such as cerium which mitigates chemical attacks on the membrane. However, these additives migrate during fuel cell operation causing a loss in durability and performance due to detrimental interaction with various components of the fuel cell. Here, we study cation size selective agents as a means to immobilize cerium within perfluorosulfonic acid (PFSA) membranes. We synthesized an organometallic complex of cerium with 15-Crown-5 and investigated the effectiveness of this complex to immobilize cerium. Over 300% increase in cerium retention and an 80% increase in chemical durability were observed owing to the stabilization effect of crown ethers on cerium. Migration under a potential gradient can be eliminated while the complex also contributes to the enhancement in cerium radical scavenging activity. In conclusion, current challenges with the proposed solution are highlighted and future work is discussed.

25 ENERGY STORAGE↗
DOE OSTI2020

Fluorinated co-solvent promises Li-S batteries under lean-electrolyte conditions

Practical lithium-sulfur batteries stipulate the use of a lean-electrolyte and a high Coulombic efficiency of the lithium metal anode. In this work, we employ 1,1,2,2-tetrafluoroethyl 2,2,2-trifluoroethyl ether as a co-solvent in the electrolyte of Li-S batteries to meet the demands. The co-solvent fosters the formation of a LiF-rich solid electrolyte interphase on lithium metal anode, as revealed by Ab initio molecular dynamics and Femtosecond Stimulated Raman spectroscopy. The co-solvent results in an average Coulombic efficiency of 99.4% for lithium plating/stripping cycles. Full cells with a capacity ratio of 2 between lithium anode and the S@PAN cathode (3 gs cm –2 ) exhibited a stable cycle life over 100 cycles at an electrolyte/sulfur ratio of 2 µL mg –1 , validating the high Coulombic efficiency of the lithium anode and demonstrating the compatibility of the electrolyte with both electrodes. To enhance the energy density, we prepared a hybrid cathode composed of 45 wt.% VS 2 mixed with ZnS-coated Li 2 S@graphene as the cathode. Based on the mass of both electrodes and the electrolyte, the full cell delivers an energy density of 483 Wh kg –1 , which demonstrates viable Li-S batteries with the lean-electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2021

Boric acid removal with polyol-functionalized polyether membranes

Poor selectivity of conventional desalination membranes for boron often necessitates multi-stage treatment trains to achieve desired boron removal for end uses such as irrigation. One approach to membrane design for improved single-pass boric acid removal is via incorporation of chelating ligands that selectively sorb boron. In this study, membranes based on epoxy-amine cross-linked poly(glycidyl glycidyl ether) (PGGE) were synthesized and functionalized with N-methyl-d-glucamine (NMDG), a polyol known to interact selectively with boron. PGGE and PGGE-NMDG membranes exhibited boron sorption isotherms that were well-described by dual mode isotherms. PGGE-NMDG sorbed 2.5 mmol B/g dry polymer from a neutral aqueous solution containing 100 mmol B/L, which was almost three times the adsorption density of a commercial boron selective resin, Amberlite IRA743. Further, the membranes were regenerated in acid without a significant loss of boron sorption capacity over four cycles. Interactions between boron and NMDG and PGGE sites (e.g., epoxides) impacted boron diffusion in both membranes. The use of ligand functionalized membranes to capture target solutes such as boron requires high loading of interacting sites to maximize uptake capacity. Establishing fundamental structure/property rules for boron selectivity could lead to new material designs with improved boron separation properties for water purification.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Plasma-assisted deflagration to detonation transition in a microchannel with fast-frame imaging and hybrid fs/ps coherent anti-Stokes Raman scattering measurements

Our study examines kinetic enhancement by nanosecond dielectric barrier discharge (ns-DBD) plasma on fuellean dimethyl ether (DME), oxygen (O 2 ), and argon (Ar) premixtures during deflagration to detonation transition (DDT) experiments in a microchannel. Non-equilibrium plasma produces active species and radicals and creates fast and slow heating of a mixture to promote ignition due to electronic and vibrational excitation. Experiments have been conducted to examine the influence of the plasma discharge on the premixture and on the resultant deflagration to detonation transition (DDT) onset time and distance through the use of high speed imaging and one-dimensional, two-beam, femtosecond/picosecond, coherent anti-Stokes Raman scattering (CARS). A highspeed camera is used to trace the time histories of flame front position and velocity and to identify the dynamics and onset of DDT. The results show that plasma discharge can nonlinearly affect the onset time and distance of DDT. It is shown that a small number of plasma discharge pulses prior to ignition result in reduced DDT onset time and distance by 60% and 40%, respectively, when compared to the results without pre-excitation by ns discharges. The results also show that an increase of plasma discharge pulses results in an extended DDT onset time and distance of 224% and 94%, respectively. Time history of the deflagration wave speed of DME and the analysis of ignition timescale under the choking condition of the deflagration front suggest low temperature ignition may play a role for DME near the isobaric choking condition of the burned gas and the DDT. Plasmainduced conversion of the reactive mixture was assessed via the O 2 to CO 2 ratio as measured through fs/ps CARS during the DBD discharges. The present experiments demonstrate the ability of non-equilibrium plasma to alter the chemistry of DME/O 2 /Ar premixtures in order to control DDT for applications in advanced propulsion engines.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Flame stabilization in DME spray flames under engine-relevant conditions characterized by OH* chemiluminescence and formaldehyde laser-induced fluorescence

The transient and quasi-steady flame structures of Dimethyl Ether (DME) fuel sprays, produced by a single-hole injector (Spray D), were investigated using Planar Laser-Induced Fluorescence (PLIF) and chemiluminescence imaging in a constant-volume chamber under Engine Combustion Network (ECN) Spray A conditions (900 K ambient temperature, 60 bar ambient pressure, 1500 bar injection pressure, and 22.8 kg/m 3 ambient density). Low-temperature chemical reaction zones were visualized using formaldehyde (CH 2 O) PLIF with 355 nm excitation, while high-temperature flame regions were captured via chemiluminescence imaging of excited-state hydroxyl radicals (OH*). Both transient and quasi-steady flame structures clearly show the transition from CH 2 O to OH*, highlighting the progression from low- to high-temperature combustion, while the position of the flame is displaced for DME compared to reference hydrocarbon n-dodecane. Homogeneous reactor calculations with detailed chemistry and using adiabatic mixing for initial temperature show that CH 2 O peaks are significantly higher for DME at the same equivalence ratio, with a higher heat-release during the cool-flame regime with respect to the fuel heating value. Thus, the cool-flame dynamic as a precursor to high-temperature combustion and flame stabilization exhibit distinct behavior for DME relative to conventional hydrocarbons, and these phenomena are effectively resolved through the soot-free nature of DME and the high-speed, time-resolved diagnostics.

CH2O laser-induced fluorescence↗
DOE OSTI2025

Discovery, characterization, and application of chromosomal integration sites in the hyperthermophilic archaeon Sulfolobus islandicus

Sulfolobus islandicus , an emerging archaeal model organism, offers unique advantages for metabolic engineering and synthetic biology applications owing to its ability to thrive in extreme environments. Although several genetic tools have been established for this organism, the lack of well-characterized chromosomal integration sites has limited its potential as a cellular factory. Here, in this work, we systematically identified and characterized 13 artificial CRISPR RNAs targeting eight integration sites in S. islandicus using the CRISPR-COPIES pipeline and a multi-omics-informed computational workflow. We leveraged the endogenous CRISPR-Cas system to integrate the reporter gene lacS and validated heterologous expression through a β-galactosidase assay, revealing significant positional effects. As a proof of concept, we utilized these sites to genetically manipulate lipid ether composition by overexpressing glycerol dibiphytanyl glycerol tetraether (GDGT) ring synthase B (GrsB). This study expands the genetic toolbox for S. islandicus and advances its potential as a robust platform for archaeal synthetic biology and industrial biotechnology.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Unimolecular Dynamics of Partially Deuterated Hydroperoxyalkyl Intermediates (•QOOD) in Cyclohexane and Cyclopentane Oxidation

The hydroperoxyalkyl radicals (•QOOH) formed in cyclohexane and cyclopentane oxidation with carbon radical center at the β site relative to the hydroperoxy group have recently been observed through their infrared fingerprint and time- and energy-resolved unimolecular dissociation dynamics to hydroxyl (OH) radical and cyclic ether products. Partial deuteration shifts the IR transitions associated with OH/OD motion to lower frequencies, providing a new window on the IR spectroscopy and unimolecular dynamics of these transient intermediates. Specifically, the overtone OD stretch (2ν OD ) has been identified at 5215.0 cm –1 and 5216.0 cm –1 for the β-QOOD intermediates in cyclohexane and cyclopentane oxidation, respectively. Unimolecular decay rates of the •QOOD intermediates at these energies have been obtained from the time-resolved appearance of OD products. The experimental rates are compared with statistical microcanonical rates evaluated using RRKM theory, including heavy-atom tunneling associated with simultaneous O–O bond elongation and C–O–O angle contraction along the reaction pathway. The experimental rates provide a further test of the previously determined transition state (TS) barriers, which were computed utilizing a benchmarking approach that builds on higher-level reference calculations for the smaller ethane oxidation system. Here, the experimental rate measurements for both •QOOD intermediates agree well with the computed rates after accounting for small changes in zero-point energy and a minor empirical adjustment of the TS barriers in both systems.

Ethers↗
DOE OSTI2023

Entropic Penalty Switches Li + Solvation Site Formation and Transport Mechanisms in Mixed Polarity Copolymer Electrolytes

Emerging solid polymer electrolyte (SPE) designs for efficient Li-ion (Li + ) conduction have relied on polarity and mobility contrast to improve conductivity. To further develop this concept, we employ simulations to examine Li + solvation and transport in poly(oligo ethylene methacrylate) (POEM) and its copolymers with poly(glycerol carbonate methacrylate) (PGCMA). We find that Li + is solvated by ether oxygens instead of the highly polar PGCMA, due to lower entropic penalties. The presence of PGCMA promotes single-chain solvation, thereby suppressing interchain Li + hopping. The conductivity difference between random copolymer PGCMA-r-POEM and block copolymer PGCMA-b-POEM is explained in terms of a hybrid solvation site mechanism. With diffuse microscopic interfaces between domains, PGCMA near the POEM contributes to Li + transport by forming hybrid solvation sites. The formation of such sites is hindered when PGCMA is locally concentrated. These findings help explain how thermodynamic driving forces govern Li + solvation and transport in mixed SPEs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Effect of Building Block Connectivity and Ion Solvation on Electrochemical Stability and Ionic Conductivity in Novel Fluoroether Electrolytes

Novel electrolytes are required for the commercialization of batteries with high energy densities such as lithium metal batteries. Recently, fluoroether solvents have become promising electrolyte candidates because they yield appreciable ionic conductivities, high oxidative stability, and enable high Coulombic efficiencies for lithium metal cycling. However, reported fluoroether electrolytes have similar molecular structures, and the influence of ion solvation in modifying electrolyte properties has not been elucidated. In this work, we synthesize a group of fluoroether compounds with reversed building block connectivity where ether moieties are sandwiched by fluorinated end groups. These compounds can support ionic conductivities as high as 1.3 mS/cm (30 °C, 1 M salt concentration). Remarkably, we report that the oxidative stability of these electrolytes increases with decreasing fluorine content, a phenomenon not observed in other fluoroethers. Using Raman and other spectroscopic techniques, we show that lithium ion solvation is controlled by fluoroether molecular structure, and the oxidative stability correlates with the “free solvent” fraction. Finally, we show that these electrolytes can be cycled repeatedly with lithium metal and other battery chemistries. Understanding the impact of building block connectivity and ionic solvation structure on electrochemical phenomena will facilitate the development of novel electrolytes for next-generation batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Solvent-driven fractional crystallization for atom-efficient separation of metal salts from permanent magnet leachates

Abstract This work reports a dimethyl ether-driven fractional crystallization process for separating rare earth elements and transition metals. The process has been successfully applied in the treatment of rare earth element-bearing permanent magnet leachates as an atom-efficient, reagent-free separation method. Using ~5 bar pressure, the solvent was dissolved into the aqueous system to displace the contained metal salts as solid precipitates. Treatments at distinct temperatures ranging from 20–31 °C enable crystallization of either lanthanide-rich or transition metal-rich products, with single-stage solute recovery of up to 95.9% and a separation factor as high as 704. Separation factors increase with solution purity, suggesting feasibility for eco-friendly solution treatments in series and parallel to purify aqueous material streams. Staged treatments are demonstrated as capable of further improving the separation factor and purity of crystallized products. Upon completion of a crystallization, the solvent can be recovered with high efficiency at ambient pressure. This separation process involves low energy and reagent requirements and does not contribute to waste generation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Identifying Bounds of Inorganic Content in Solventless Processing of Hybrid Solid Electrolytes

Solid-state lithium batteries require safe, robust electrolytes to enable higher energy densities and improved safety over conventional cells. Hybrid polymer–ceramic electrolytes are a promising solution, combining the processability of polymers with the high ionic conductivity and mechanical strength of inorganic fillers. In this work, we demonstrate a solventless, UV-curing method to produce hybrid solid electrolytes using a poly(ethylene glycol) dimethyl ether (PEGDME)-based photocurable matrix incorporating Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) or Li 7 La 3 Zr 2 O 12 (LLZO) ceramic electrolyte. Inorganic filler loadings up to ∼55 wt.% could be successfully incorporated via this process which was the highest inorganic content at which the slurry remains processable and cured into a uniform film. The resulting UV-cured composite electrolytes remain flexible and exhibit room-temperature ionic conductivities on the order of 10 −4 S·cm −1 , along with notably improved lithium-ion transference numbers compared to conventional polymer electrolytes. Similar performance and processing limits were observed for both LAGP and LLZO, indicating that ceramic filler chemistry does not significantly affect the UV-curing process or the electrolyte's ion transport properties in this regime. Eliminating solvents from fabrication not only simplifies processing and mitigates environmental concerns but also enables higher solid contents that enhance mechanical strength and help suppress lithium dendrite formation. In conclusion, this scalable approach thus paves the way for manufacturing robust composite solid electrolytes for next-generation solid-state batteries (SSBs).

Batteries↗