Search NASA⌕ Search

SEARCH · Search NASA

Results for “fuel melting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Neutron Dosimetry for the Colorado School of Mines (CSM 16-10584) Irradiation in ATR

PNNL project 74242 involves the analysis of neutron fluence monitors irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory in accordance with MPO 00236287 and Statement of Work No. 17370, Rev. 0, PNNL Analysis of NSUF Flux and Melt Wire Capsules. This report is for the Colorado School of Mines (CSM 16-10584) experiment which was conducted in position B5 of the ATR. Three other irradiations included in the scope of work are reported separately. The neutron fluence monitors were prepared by PNNL and loaded into the CSM assemblies at INL prior to irradiation. Following irradiation, the capsules were returned to PNNL for analysis. The neutron dosimetry capsules were opened, the flux wires were removed for gamma analysis, and the measured activities were used to determine the activation rates for various activation products. Following suitable corrections, the measured activation rates were used to adjust calculated neutron spectra at 12 fluence monitor locations. The adjusted neutron spectra were then used to determine displacement per atom (dpa) and gas production for irradiated materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Neutron Dosimetry for the University of Central Florida (UCF3) Irradiation in ATR

PNNL project 74242 involves the analysis of neutron fluence monitors irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory in accordance with MPO 00236287 and Statement of Work No. 17370, Rev. 0, PNNL Analysis of NSUF Flux and Melt Wire Capsules. This report is for the University of Central Florida (UCF)-3 third stage experiment which was conducted in position B8 of the ATR. Three other irradiations included in the scope of work are reported separately. The neutron fluence monitors were prepared by PNNL and loaded into the UCF-3 assemblies at INL prior to irradiation. Following irradiation, the capsules were returned to PNNL for analysis. The neutron dosimetry capsules were opened, the flux wires were removed for gamma analysis, and the measured activities were used to determine the activation rates for various activation products. Following suitable corrections, the measured activation rates were used to adjust calculated neutron spectra at 8 fluence monitor locations. The adjusted neutron spectra were then used to determine displacement per atom (dpa) and gas production for irradiated materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High-Performance SiC/SiC Ceramic Composite Systems Developed for 1315 C (2400 F) Engine Components

As structural materials for hot-section components in advanced aerospace and land-based gas turbine engines, silicon carbide (SiC) ceramic matrix composites reinforced by high performance SiC fibers offer a variety of performance advantages over current bill-of-materials, such as nickel-based superalloys. These advantages are based on the SiC/SiC composites displaying higher temperature capability for a given structural load, lower density (approximately 30- to 50-percent metal density), and lower thermal expansion. These properties should, in turn, result in many important engine benefits, such as reduced component cooling air requirements, simpler component design, reduced support structure weight, improved fuel efficiency, reduced emissions, higher blade frequencies, reduced blade clearances, and higher thrust. Under the NASA Ultra-Efficient Engine Technology (UEET) Project, much progress has been made at the NASA Glenn Research Center in identifying and optimizing two highperformance SiC/SiC composite systems. The table compares typical properties of oxide/oxide panels and SiC/SiC panels formed by the random stacking of balanced 0 degrees/90 degrees fabric pieces reinforced by the indicated fiber types. The Glenn SiC/SiC systems A and B (shaded area of the table) were reinforced by the Sylramic-iBN SiC fiber, which was produced at Glenn by thermal treatment of the commercial Sylramic SiC fiber (Dow Corning, Midland, MI; ref. 2). The treatment process (1) removes boron from the Sylramic fiber, thereby improving fiber creep, rupture, and oxidation resistance and (2) allows the boron to react with nitrogen to form a thin in situ grown BN coating on the fiber surface, thereby providing an oxidation-resistant buffer layer between contacting fibers in the fabric and the final composite. The fabric stacks for all SiC/SiC panels were provided to GE Power Systems Composites for chemical vapor infiltration of Glenn designed BN fiber coatings and conventional SiC matrices. Composite panels with system B were heat treated at Glenn, and the pores that remained open were filled by silicon melt infiltration (MI). Panels with system A and the other SiC/SiC systems were not heat treated, and remaining open pores in these systems were filled with SiC slurry and silicon MI.

DiCarlo, James A.↗

Corrosion testing needs and considerations for additively manufactured materials in nuclear reactors

Metal additive manufacturing holds significant promise as an enabling technology for the 21st century nuclear energy industry. Metal additive manufacturing (MAM) can allow the fabrication of novel materials and innovative component designs that are not achievable through conventional manufacturing. Due to its very different fabrication methods, as-fabricated MAM components are characteristically different from conventionally manufactured components. MAM materials exhibit very different microstructures from conventional cast or wrought materials. For example, austenitic stainless steels fabricated by laser powder bed fusion exhibit columnar grain structures, dislocation cell structures, and melt pool fingerprints. In addition, MAM fabrication may result in defects such as porosity, incomplete processing of the feedstock (e.g., lack of fusion in melt-based methods), and oxide inclusions. Heat treatments may further evolve the microstructure, microsegregation, and stresses within the component. Furthermore, MAM components have a rough surface with feature sizes on the order of the feedstock material, as opposed to smooth surfaces resulting from conventional machining and forming operations. As a result, the corrosion behavior of MAM components will likely be significantly different from that of conventionally formed components. Corrosive environments for structural materials within advanced reactor environments include molten fluoride and chloride salts, liquid sodium and lead-bismuth, and high-temperature helium. The Advanced Materials and Manufacturing Technologies program within the Department of Nuclear Energy in the United States Department of Energy is assessing the unique concerns of MAM component corrosion and testing methodologies in advanced nuclear reactor environments. We discuss these concerns and testing strategies in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High Temperature Additive Architectures for 65% Efficiency (Final Technical Report)

This project aimed to develop advanced high-temperature additive components that contribute towards the DOE’s goal for advanced gas turbines that are capable of at least 65% efficiency in combined cycle application. The objective was to leverage state-of-the-art additive manufacturing to develop an innovative stage 1 turbine nozzle (S1N) that can provide cooling flow savings while maintaining the component durability expected in today’s gas turbines. The program had two phases. Phase I was a conceptual phase for novel advanced cooling designs enabled by additive manufacturing, as well as proposals for validation. Phase II included execution of the Phase I conceptual design, including manufacturing of prototype hardware and validation within an environment that is similar to engine operation. During Phase I of the program, the team devised a concept to reduce cooling air usage. The cooling air used in the side walls is filmed out along the side walls, while the cooling air used in the airfoil is eventually directed to near-wall channels and exits holes along the airfoil trailing end. During this program, the team performed additive trials to analyze the geometric limitations of additive manufacturing. This helped the team understand minimum wall thicknesses, hole sizes, and cooling channel dimensions among other limits. Phase II of this program pushed GE Vernova beyond its previous experience of designing and manufacturing an additively manufactured hot gas path component. Modern hot gas path components utilize material chemistries that are traditionally hard to weld, such as cast Renè 108, and exhibit solidification cracking when additively manufactured using Direct Metal Laser Melting (DMLM). Note that AM108 is a powder form of Renè 108. A S1N with advanced cooling is larger and more complex than parts previously built by additive manufacturing and required new learnings to resolve risks around solidification cracking. Finally, the team validated the design in a combustion rig that replicated operation in a gas turbine. In order to properly quantify the benefits of the new additive design, a baseline was also tested in the rig and operated under the same conditions. In addition, an uncertainty analysis was done to quantify any sources of error that could impact the results. At the end of the validation effort, it was determined that the additive nozzle exceeded the 15% reduction in cooling flow goal even with the worst-case assumptions for uncertainty.

03 NATURAL GAS↗

Parametric Study of Panel PCM–Air Heat Exchanger Designs

Heat exchangers, devices for the transfer of heat between two or more working fluids, are extensively used in cooling applications and heating applications. Heat exchangers in buildings are typically components of space-conditioning systems, as well as of water-heating applications. Heat exchangers are also sometimes used in applications that require storage and release of energy at specific times. Phase change materials (PCMs) enhance these heat-exchange processes, given their ability to melt and solidify at a fixed range of temperatures, absorbing or releasing significant amounts of latent heat. Five different configurations of PCM–air heat exchangers for thermal control in buildings are analyzed in this work. The heat exchangers were fitted with PCM encapsulated in plastic and composite pouches of various shapes, and packaged in stackable panel layers. Three-dimensional computational fluid dynamics (CFD) modeling of coupled incompressible fluid and conjugate heat transfer were performed on the designs. The phase change process was numerically modelled using the apparent heat capacity method. Steady-state CFD simulations provided quantification of pressure drop as a function of air flow velocity. Transient simulation results describe the thermal evolution of PCM in the pouches, helping to determine the best performing configuration with respect to total thermal charging time.

10 SYNTHETIC FUELS↗

Designing Recyclable Biomass-Based Polyesters (Final Technical Report)

This project successfully demonstrated the production of sustainable polyesters from biomass-derived monomers, offering properties on par with or superior to fossil-based plastics such as LLDPE and PBAT. Using renewable chemical platforms like furfural and HMF, we synthesized over eight novel monomers and nearly 100 aliphatic-aromatic polyesters. Among these, PPeAT and PDDF emerged as highly promising candidates for flexible packaging applications, exhibiting excellent mechanical performance, tunable thermal properties, and enhanced barrier characteristics. Key advances included the development of ring-opening polymerization strategies using cyclic monomer intermediates to produce high molecular weight materials with excellent control. The resulting polymers achieved biobased content of at least 44 wt.%. We also implemented chemical recycling via catalytic methanolysis, recovering over 90% of monomers from PPeAT at semi-pilot scale. This supports a circular economy approach by enabling material reuse without performance loss. Techno-economic and life cycle assessments confirmed that these polyesters can reduce greenhouse gas emissions by up to 50% compared to petroleum-derived alternatives. Favorable mechanical properties may further reduce material demand, and cost competitiveness was demonstrated under specific market conditions. Feedstock cost and environmental footprint were identified as primary levers for future optimization. In summary, the project met or closely approached all technical targets, including biodegradability, strength, and processing compatibility. While minor issues such as color and melting point variation remain, the results strongly support continued development and scale-up of these sustainable materials.

09 BIOMASS FUELS↗

Composite-Material Tanks with Chemically Resistant Liners

Lightweight composite-material tanks with chemically resistant liners have been developed for storage of chemically reactive and/or unstable fluids . especially hydrogen peroxide. These tanks are similar, in some respects, to the ones described in gLightweight Composite-Material Tanks for Cryogenic Liquids h (MFS-31379), NASA Tech Briefs, Vol. 25, No. 1 (January, 2001), page 58; however, the present tanks are fabricated by a different procedure and they do not incorporate insulation that would be needed to prevent boil-off of cryogenic fluids. The manufacture of a tank of this type begins with the fabrication of a reusable multisegmented aluminum mandrel in the shape and size of the desired interior volume. One or more segments of the mandrel can be aluminum bosses that will be incorporated into the tank as end fittings. The mandrel is coated with a mold-release material. The mandrel is then heated to a temperature of about 400 F (approximately equal to 200 C) and coated with a thermoplastic liner material to the desired thickness [typically approxiamtely equal to 15 mils (approximately equal to 0.38 mm)] by thermal spraying. In the thermal-spraying process, the liner material in powder form is sprayed and heated to the melting temperature by a propane torch and the molten particles land on the mandrel. The sprayed liner and mandrel are allowed to cool, then the outer surface of the liner is chemically and/or mechanically etched to enhance bonding of a composite overwrap. The etched liner is wrapped with multiple layers of an epoxy resin reinforced with graphite fibers; the wrapping can be done either by manual application of epoxy-impregnated graphite cloth or by winding of epoxy-impregnated filaments. The entire assembly is heated in an autoclave to cure the epoxy. After the curing process, the multisegmented mandrel is disassembled and removed from inside, leaving the finished tank. If the tank is to be used for storing hydrogen peroxide, then the liner material should be fluorinated ethylene/propylene (FEP), and one or more FEP O ring(s) should be used in the aluminum end fitting(s). This choice of materials is dictated by experimental observations that pure aluminum and FEP are the only materials suitable for long-term storage of hydrogen peroxide and that other materials tend to catalyze the decomposition of hydrogen peroxide to oxygen and water. Other thermoplastic liner materials that are suitable for some applications include nylon 6 and polyethylene. The processing temperatures for nylon 6 are lower than those for FEP. Nylon 6 is compatible with propane, natural gas, and other petroleum-based fuels. Polyethylene is compatible with petroleum- based products and can be used for short-term storage of hydrogen peroxide.

DeLay, Thomas K.↗

Flexible Fuel Electric Hybrid Glass Furnace Demonstration

The furnace contractor completed General Arrangement (GA) layouts and Piping and Instrumentation Diagrams (P&ID) for both furnaces during this reporting period. Preliminary equipment lists accompanied this work. Control system architecture in progress. Key furnace design elements and deliverables on track to be complete by end of phase. The facilities design and integration contractor completed a 3D scan and modeling of the facility. The work during this period focused on preliminary design with a focus on overall project scope and feasibility. This key work supports the overall project deliverables for 30% preliminary engineering and Preliminary Design Report (PDR) which are on track to be complete by the end of the phase. These deliverables are approximately 50% complete through the end of this reporting period. The batch house operations design contractor continues development of site plan and General Arrangement (GA) layout to support the 30% preliminary engineering and design package. This work is 60% complete by the end of this reporting period and is on track to be complete by the end of the phase.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Integrated Transpiration and Lattice Cooling Systems developed by Additive Manufacturing with Oxide-Dispersion-Strengthened (ODS) Alloys (Final Report)

The primary goal of this research was to develop an innovative approach to provide a significantly improved level of thermal protection for hot-section components, such as turbine airfoils, in modern and future gas turbines. Current and future designs for “air breathing” turbine systems are targeting turbine inlet temperatures of 1700°C or higher, which is well beyond the substrate melting temperature, and a combined cycle energy efficiency of 65%. Meanwhile, targeted cycle efficiency calls for a reduction of the amount of coolant air significantly below the current level. Hence the development of novel internal airfoil designs that provide a satisfactory level of component durability with affordable coolant management is critical to the further advances of today’s turbine technology. This project was a response to this grand challenge with the research efforts primarily focused on the development of integrating transpiration cooling with lattice enhanced internal cooling. The research on these advanced cooling technologies was accompanied with development of anti-oxidation material in the form of oxide dispersion strengthened (ODS) alloy which also possessed enhanced high temperature strength. A novel approach of fabricating the ODS alloy as powder with high compatibility with state-of-the-art additive manufacturing (AM) process was also developed.

03 NATURAL GAS↗

Initial Neutronics Investigation of a Chlorine Salt-Based Breeder Blanket

Tritium breeding blankets within D-T-fueled fusion reactors contain lithium compounds and typically require neutron multiplier materials to achieve a tritium breeding ratio (TBR) consistent with self-sustaining operation. Liquid breeder blankets have some advantages over solid blankets, and previous blanket studies have investigated liquid metal as well as liquid salt–based blankets. Liquid salts have reduced magnetohydrodynamic effects as compared to liquid metals, but typically have a lower TBR. Recently, advanced fission reactor concepts have considered chloride-based salts in their design, and there is a significant amount of research work occurring to study these salts. Chloride salts have previously been considered for fusion reactors, but studies have typically found lower breeding ratios than for fluoride salts, such as 2(LiF)-BeF 2 (flibe) so they have not been further developed. In this work, we use a one-dimensional cylindrical radiation transport model of a conceptual tokamak fusion reactor to investigate the neutronics feasibility of using a chloride salt–based blanket that uses chlorine enriched in 37 Cl, which has both a low capture cross section and a substantial (n,2n) cross section. It is found that chloride salts (LiCl mixed with BeCl 2 and/or PbCl 2 ) can potentially achieve a ~3% to 5% higher TBR than fluoride molten salts, notably flibe, in the absence of a solid multiplier. Including a solid multiplier, however, does narrow this advantage, with TBRs estimated within ~1% of flibe with a 2-cm Be multiplier. Chloride salts can also reach lower melting points than flibe, potentially improving the scope for the use of reduced activation ferritic-martensitic steel as a structural material. There is substantial uncertainty in the calculations driven by limited thermochemical data for the Cl salts, plus cross-section uncertainties. The production of 36 Cl through 35 Cl(n,g) and 37 Cl(n,2n) has the potential to challenge the waste disposal rating of the blanket. Calculations indicate that, while this is not an immediate showstopper, this case depends upon the exact waste disposal rating criteria used for 36 Cl. Further work could reduce these uncertainties with improved thermochemical data, higher-fidelity modeling for downselected salts, and more refined waste disposal calculations and regulatory guidance. Lastly, it must be recognized that, as for all molten salts, corrosion and chemistry can present appreciable technical challenges that require further assessment in developing a practical blanket concept, and also that the enrichment of chlorine presents an additional technical and supply chain challenge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Molten Salt Lattice Confinement Fusion (LCF) Fast Fission Reactor for Lunar and Planetary Surface Power

Molten salt fission reactors (MSR) have been suggested for lunar and planetary surface power systems. They have the advantage of operating at high temperature, for efficient thermal-electrical conversion, low pressure, long-lived with high nuclear fuel burnup. MSR are often designed to breed fissile 233U from natural 232Th by neutron capture and  decay via: 232Th(n,)233Th(,)233Pa(,)233U Unfortunately, this process requires 233Pa isotope separation and segregation to decay to 233U. This requirement prevents additional neutron capture that interferes with 233U breeding. Instead, Wooley’s sub-critical, fast fission, molten salt reactor would use externally generated tokamak fusion neutrons1,2 to fission all actinides.We propose a simpler fusion-fast-fission sub-critical reactor that generates fast neutrons in situ from lattice confinement fusion (LCF) to fission fertile and fissile actinides. This hybrid reactor doesn't require enriched 235U fissile pins to initiate fis-sion reactions, nor 233Pa separation and segregation during operation. Like Wooley’s, this hybrid reactor “burns” natural uranium (238U) or thorium (232Th) which avoids uranium enrichment and additional fissile material launch safety and security costs. The LCF neutron source is initiated by bremsstrahlung photoneutrons (Fig. 1)3 or isotopic neutron sources in electron-screened lattices (Fig. 2)4,5. Alternatively, the electrolytic Pd-deuterium co-deposition6protocol fast fissions7 both 232Th and 238U. However, an aqueous electrolyte-based system, without pressurization similar to conventional pressurized water fission reactors, is incapable of high temperatures due to the boiling point of the electrolyte slightly over 100 C. Molten salts can be used instead as was demonstrated at the University of Hawaii8 using a variety of Ni and Pd cathodes in lithiated, hydrided and deuterated salts. These salts have melting points often exceeding 500C making them suitable to efficiently produce electrical power9 through either Advanced Stirling Genera-tors (< 100 kWe) or closed-Brayton Cycle (> 100 kWe). This hybrid reactor could power a wide range of lunar or Martian applications from unmanned in-struments, to charging vehicles and entire facilities such as human habitats or in situ resource utilization. The power conversion cycles are Carnot Cycle limited, but generally 30% efficient at best. However, waste heat on the moon or Mars is important to surviving either two-week lunar nights or Martian nights as well as providing process heat for mineral extraction and “living off the land”

Lawrence Forsley↗

Derivation of physical equations for high-speed laser welding using large language models

It is challenging to formulate complex physical phenomena that occur in a manufacturing process, particularly when the available data are limited, rendering conventional data-driven approaches ineffective. This study aims to predict humping onset in high-speed laser welding by introducing a novel framework, namely text-to-equations generative pre-trained transformer (T2EGPT). This method leverages the capabilities of large language models (LLMs), in combination with sparse experimental data and enriched literature data, to derive an interpretable and generalizable equation for predicting humping initiation. By capturing key correlations among physical parameters, T2EGPT generates a compact and dimensionless expression that accurately predicts hump formation. The equation reveals that humping arises from the interplay between inertia-driven backward melt flow and capillary-driven surface stabilization, where inertial forces drive molten metal backward and capillary forces resist surface deformation. Furthermore, compared to traditional data-driven models, T2EGPT demonstrates enhanced predictive accuracy and cross-material transferability. More broadly, this study highlights the potential of LLMs to integrate textual information with data-driven discovery, enabling the extraction of physical laws in data-scarce scientific domains.

36 MATERIALS SCIENCE↗

Combustion of a polymer (PMMA) sphere in microgravity

Polymer combustion is a highly complicated process where chemical reactions may occur not only in the gas phase, but also in the condensed phase as well as at the solid-gas interphase. The chemistry depends strongly on the coupling between the condensed phase and gas phase phenomena. For some polymers, additional complications arise due to the formation of char layers. For others, the behavior of the condensed phase involves swelling, bubbling, melting, sputtering, and multi-stage combustion. Some of these features bear resemblance to the phenomena observed in coal particle combustion. In addition to its relevance to spacecraft fire safety, the combustion of polymeric materials is related to many applications including solid and hybrid rocket propulsion, and of recent interest, waste incineration . The burning rate is one of the most important parameters used to characterize the combustion of polymers. It has been used to rank the polymer flammability under the same experimental conditions and to evaluate various modes of inhibiting polymer flammability. The main objective of this work is to measure the burning rates of a polymeric material in low gravity. Because of inherent logistical difficulties involved in microgravity experiments, it is impossible to examine a wide spectrum of polymeric materials. It is desirable to investigate a polymer whose combustion is less complicated, and yet will lead to a better understanding of the burning characteristics of other more complicated materials. Therefore, a typical non-charring polymer is selected for use in this experimental study. PMMA (polymethylmethacrylate) has been chosen because its thermo-physical properties are well characterized. Although the combustion of PMMA has been extensively studied in 1G experiments, only a limited amount of work has been conducted in low gravity. A spherical sample geometry is chosen in this study because it is the simplest configuration in terms of the microgravity hardware design requirements. Furthermore, a burning PMMA sphere in microgravity represents a one-dimensional flame with overall combustion characteristics expected to be analogous to the combustion of a liquid fuel droplet, a field with many well-developed theories and models. However, differences can also be expected such as the flame-front standoff ratios and the condensed phase processes occurring during combustion.

Yang, Jiann C.↗

Closed‐Loop Recycling of Poly(pentylene Adipate‐ co ‐Terephthalate) via Amine‐Catalyzed Methanolysis

Advancing circularity through effective chemical recycling strategies is essential for enabling the sustainable use of emerging biodegradable polyesters in film applications. In this context, poly(pentylene adipate-co-terephthalate) with a 40/60 adipate-to-terephthalate ratio (PPeAT60), a significantly stiffer and partially biobased copolyester recently reported by our team, offers improved mechanical performance and processability compared to commercial poly(butylene adipate-co-terephthalate), while providing a platform to evaluate advanced recycling approaches for film applications. Here, this study describes depolymerization of PPeAT60 through amine-catalyzed methanolysis, followed by the repolymerization of the recovered monomers. The resulting repolymerized material exhibited a molar mass distribution, chemical structure, and thermal stability comparable to the virgin polymer, confirming the technical feasibility of the methanolysis-based recycling route. Both polymers displayed nearly identical melting, glass transition, and decomposition temperatures, crystallinity, and modulus, demonstrating full structural and mechanical reproducibility after recycling. Variations in crystallization kinetics, elongation at break, and barrier properties likely arise from trace impurities (<1%) introduced during processing acting as nucleating and stress-inducing agents. Overall, these results demonstrate that PPeAT60 retains its key properties after chemical recycling, establishing methanolysis as a promising platform for recycling of this partially biobased polymer that may be able to replace both conventional polyolefins and PBAT in flexible packaging applications.

09 BIOMASS FUELS↗

Indications of flat bands driving the δ to α volume collapse of plutonium

On cooling from the melt, plutonium (Pu) undergoes a series of structural transformations accompanied by a ≈ 28% reduction in volume from its δ phase to its α phase at low temperatures. While Pu’s partially filled 5 f -electron shells are known to be involved, their precise role in the transformations has remained unclear. By using calorimetry measurements on α -Pu and gallium-stabilized δ -Pu combined with resonant ultrasound and X-ray scattering data to account for the anomalously large softening of the lattice with temperature, we show here that the difference in electronic entropy between the α and δ phases dominates over the difference in phonon entropy. Rather than finding an electronic specific heat characteristic of broad f -electron bands in α -Pu, as might be expected to occur within a Kondo collapsed phase in analogy with cerium, we find it to be indicative of flatter subbands. An important role played by Pu’s 5 f electrons in the formation of its larger unit cell α phase comprising inequivalent lattice sites and varying bond lengths is therefore suggested.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Pretreatments for the continuous production of pyrolytic sugar from lignocellulosic biomass

Fast pyrolysis of lignocellulosic biomass yields little sugar or anhydrosugars compared to pyrolysis of pure polysaccharides because naturally abundant alkali and alkaline earth metals (AAEM) in biomass catalyze the fragmentation of pyranose and furanose rings. Sugar yields can be increased dramatically by pretreating the biomass with sulfuric acid prior to pyrolysis, which passivates the catalytic activity of the metals by converting them into thermally stable salts. However, depolymerization of lignin in biomass also depends on the catalytic activity of AAEM. Thus, passivating AAEM has the unintended consequence of slowing the rate of depolymerization and volatilization of lignin, resulting in a transient melt phase that agglomerates and can foul pyrolysis reactors. Here, to overcome this problem, various non-alkali metal sulfates were tested as replacements for sulfuric acid. Iron in the form of ferrous sulfate proved the most effective in depolymerizing lignin without fragmenting pyranose rings. Conventional nitrogen-blown pyrolysis of ferrous sulfate pretreated corn stover achieved WHSV of 4 h –1 compared to only 0.6 h –1 for acid pretreated corn stover. Autothermal (air-blown) pyrolysis of ferrous sulfate pretreated corn stover showed even more dramatic improvement, increasing WHSV from 1 h –1 to 10 h –1 compared to acid pretreated corn stover under autothermal operation. Fermentable sugar yields from the pyrolysis of corn stover increased from 0.9 wt% to 11.8 wt% on a biomass basis, a 13-fold increase as a result of the ferrous sulfate pretreatment. These advantages combine to increase volumetric sugar productivity from 62 g L –1 h –1 for conventional pyrolysis of untreated corn stover to 2041 g L –1 h –1 for autothermal pyrolysis of ferrous sulfate treated corn stover.

09 BIOMASS FUELS↗

The Role of Declining Snow Cover in the Desiccation of the Great Salt Lake, Utah, using MODIS Data

The Great Salt Lake (GSL) in Utah has been shrinking since the middle of the 19th Century, leading to decreased area and volume, and increased salinity. We use satellite data products from the Terra and Aqua MODerate-resolution Imaging Spectroradiometer (MODIS) and the Landsat-7 and -8 satellites, along with meteorological and streamflow data, and modeled data products to study the relationship between changing snow-cover conditions and the decline of the GSL since 2000 in the context of the historical record of lake levels. The GSL basin includes much of the snow-dominated Wasatch and Uinta mountain ranges to the east of the lake. Snowmelt feeds the Bear, Jordan, and Weber rivers which are the three main rivers that flow into the lake. Snowmelt-timing maps, derived from a new MODIS standard snow-cover product, MOD10A1F, show that snow melted ~9.5 days earlier in the GSL basin during the study period, extending from 2000 – 2018. Air temperatures derived from 26 meteorological stations and surface temperatures measured by the Aqua MODIS land-surface temperature (LST) products, MYD21A1D and MYD21A1N, show trends of increasing temperature of ~0.94°C (a=0.05), and ~2.18°C, respectively, with most of the LST trends in the GSL basin being statistically significant (a=0.05). Increasing air temperatures in the basin have led to less precipitation falling as snow, lower snow depth (by ~34.5 mm (=0.01)) and snow-water equivalent (0.02 mm (a=0.01)), and earlier snowmelt. Also during the study period, Global Land surface Evaporation Amsterdam Model data show evaporation increasing by ~3.2 mm/yr, with trends in much of the basin being statistically significant (a=0.05). Trends calculated from the various products are generally in agreement indicating higher temperatures, greater evaporation, less snowfall and snow-on-the ground, and earlier snowmelt. Earlier snowmelt contributes to increasing evaporative loss from water flowing toward the lake. Furthermore, a lower mountain snowpack and less precipitation falling as snow (versus rain) is associated with lower stream discharge even if overall precipitation stays the same. The surface-water temperature of the GSL also increased over the study period by ~ 0.69°C, according to the MODIS LST data products, and the surface-water elevation of the lake dropped by ~1.7 m between 2000 and 2018 based on United States Geological Survey measurements, and the areal extent of the lake decreased by ~901 km2 as measured using Landsat imagery. Desiccation of the lake is associated with deleterious effects on wildlife, recreational activities, and some local industries. And, importantly, an expanding lake bed can also fuel dust storms that promote dangerous air quality along the Wasatch Front. This work elucidates the key role that satellite remote sensing can play in documenting earlier snowmelt and other changes in the GSL basin that influence the ongoing decline of the Great Salt Lake.

Dorothy K Hall↗