Search NASA⌕ Search

SEARCH · Search NASA

Results for “geometry investigation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Physical and Chemical Responses of Amidine-Containing Polymers in the Capture and Release of CO 2

Polymeric materials containing amidine motifs are of high interest due to their ability to reversibly capture and release CO 2 at ambient temperature. Here, in this study, we probe physical and chemical responses of styrene-based copolymers containing linear amidine motifs as functions of CO 2 and inert gas exposures and temperature. A copper-catalyzed azide–alkyne cycloaddition “click” reaction involving N′-propargyl-N,N-dimethylacetamidine is used to modify random copolymers, resulting in an array of linear amidine motifs along the chain backbone with the amount of CO 2 -active amidine controlled by the copolymer composition. Through thermogravimetric measurements, we demonstrate that the amidine-functionalized copolymers efficiently capture CO 2 upon exposure to a stream of CO 2 (at 27 °C) and release it at a slightly elevated temperature (50 °C) when exposed to an inert gas stream (N 2 ). In addition to displaying a maximum adsorption capacity of 22 wt % in the presence of pure CO 2 , the copolymers show composition-dependent direct air capture (DAC) behaviors. Small molecule analogs are used to definitively understand degradation via chemical hydrolysis of the amidine moiety, which leads to insolubility and a large reduction in CO 2 adsorption capacity (1.7 wt %). Neutron vibrational spectroscopy and DFT calculations confirm that CO 2 binds strongly to the amidine motif, inducing a strong bending of the CO 2 molecule from its linear geometry. The coupled insights into mechanisms and behaviors of CO 2 adsorption in amidine-functionalized polymers provides a foundation for future investigations of CO 2 -responsive polymers and soft materials to improve carbon capture and sequestration technologies.

Chun, Danielle J.↗
DOE OSTI2020

Understanding Cation Selectivity in Carbon Nanopores with Hybrid First-Principles/Continuum Simulations: Implications for Water Desalination and Separation Technologies

Understanding ion adsorption in porous carbons is crucial for a range of technologies, including water desalination and energy storage. In this work, we combined density functional theory with a continuum solvation model to investigate thermodynamics and kinetics of the adsorption process of alkali metal ions from aqueous solutions into carbon nanopores with different sizes and geometries. We found that cations with a larger ionic radius are more favorable to enter the nanopores because of a lower energy penalty of dehydration. In addition, the pore size and geometry were found to have a significant impact on the ion–pore interaction under confinement and cation selectivity. Our study highlights a complex interplay among nanopore geometry, ion size, and hydration on the cation adsorption selectivity, suggesting that tuning the porosity could represent a general strategy for improving ion separations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Fused-ring isomerism modulates molecular packing and device performance in non-halogenated organic solar cells

Subtle changes in molecular backbone geometry impact intermolecular interactions and performance of organic solar cells. Here, three isomeric small-molecule acceptors (NaO1, NaO2, and NaO3) are investigated to reveal how different fused-ring configurations control molecular packing, electronic coupling, and film formation. Structural and spectroscopic analyses show that the linearly fused NaO1 forms a compact three-dimensional packing network with large and balanced electronic couplings (>24 meV) across multiple directions, while the more curved analogues exhibit excessive crystallization and phase segregation. In-situ optical measurements demonstrate that NaO1 promotes fast and continuous structural evolution during film formation, resulting in smooth morphology and homogeneous phase distribution. These structural and dynamic advantages facilitate efficient charge generation and transport, accompanied by reduced non-radiative energy loss, ultimately achieving an efficiency of 20.07% for non-halogenated ternary devices. Our findings highlight how fused-ring isomerism decisively governs structure–packing–performance relationships in organic solar cells.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Scaling of silicon nanoparticle growth in low temperature flowing plasmas

Low temperature plasmas are an emerging method to synthesize high quality nanoparticles (NPs). An established and successful technique to produce NPs is using a capacitively coupled plasma (CCP) in cylindrical geometry. Although a robust synthesis technique, optimizing or specifying NP properties using CCPs, is challenging. In this paper, results from a computational investigation for the growth of silicon NPs in flowing inductively coupled plasmas (ICPs) using Ar/SiH 4 gas mixtures of up to a few Torr are discussed. ICPs produce more locally constrained and quiescent plasma potentials. These positive plasma potentials produce an electrostatic trap for negatively charged NPs, which can significantly extend the residence time of NPs in the plasma, which in turn provides a controllable period for particle growth. The computational platforms used in this study consist of a two-dimensional plasma hydrodynamics model, a three-dimensional nanoparticle growth and trajectory tracking model, and a molecular dynamics simulation for deriving reactive sticking coefficients of silane radicals on Si NPs. Trends for the nanoparticle growth as a function of SiH 4 inlet fraction, gas residence time, energy deposition per particle, pressure, and reactor diameter are discussed. The general path for particle synthesis is the trapping of small NPs in the positive electrostatic potential, followed by entrainment in the gas flow upon reaching a critical particle size. Optimizing or controlling NP synthesis then depends on the spatial distribution of plasma potential, the density of growth species, and the relative time that particles spend in the electrostatic trap and flowing through higher densities of growth species upon leaving the trap.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Computational Evaluation of Thermal Response of Open-Cell Foam With Circular Pore (Computional Evaluation of Thermal Response of Open-Cell Foam with Circular Pore)

The evaluation of effective material properties in heterogeneous materials (e.g., composites or multicomponent structures) critically relevant to a wide spectrum of applications, including nuclear power, electronic packaging, flame retardants, hypersonics, and gas turbine power. The work described in this paper is centered around the numerical assessment of the thermal behavior of porous materials obtained from finite element thermal modeling and simulation. Here, two-dimensional, steady state analyses were performed on unit cells with centered, circular pores using a second order accurate Galerkin finite element method (FEM). The effective thermal conductivities of the porous systems were examined, encompassing a range of porosities from 4.9% to 60.1%. The geometries of the models were generated based on ordered circular pores for each modeled porosity level. The system response quantity (SRQ) under investigation was the dimensionless effective thermal conductivity across the unit cell. The dimensionless effective thermal conductivity was compared across all simulated cases, producing a trend between porosity and effective thermal conductivity. In the presented investigation, the method of manufactured solutions (MMS) was used to perform code verification, and the grid convergence index (GCI) was employed to estimate discretization uncertainty as solution verification. Code verification concluded an approximately second order accurate Galerkin FEM solver. It was found that the introduction of porosity to the unit cell material structure reduces effective thermal conductivity, as anticipated. Numerical results obtained in this study are compared to an analytical solution and to a sample of empirical data.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Identifying the Accuracy of Surface Roughness for Metal Additive Manufacturing Parts Captured with Computed Tomography Scanning

Conventional surface roughness measurement techniques require direct access to internal surfaces, often necessitating destructive sectioning of test articles. Computed tomography (CT) offers a non-destructive alternative for internal surface characterization, but its application in metrology remains unstandardized and sensitive to machine resolution and operator technique. This study investigates the feasibility of using CT scanning to quantify areal surface roughness in metal AM heat exchanger tubes with three distinct internal geometries: ribbed, discrete W, and featureless. CT-derived surface parameters were extracted using custom Python scripts and compared to measurements obtained from a focus variation microscope calibrated against a known standard. Results show that CT-based roughness measurements closely matched microscope values for the discrete W specimen, deviations between CT and microscope measurements were minimal—less than 1 µm—indicating reliable reconstruction. In contrast, the ribbed and featureless specimens, with lower roughness values showed greater discrepancies. The findings suggest that CT scanning can be a viable non-destructive metrology tool for AM parts with surface roughness above approximately 8 µm. For smoother surfaces, current CT capabilities may not provide sufficient accuracy, highlighting the need for resolution-aware workflows and further standardization in CT-based surface metrology.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Recent Progress on Numerical Modeling for Microgravity Electric Field Flames: Preprint

This paper presents the recent progress on the NASA Physical Science Informatics (PSI) project PeleLM CFD of Ion Driven Winds from Diffusion Flames in simulating the E-FIELD Flames microgravity results. The focus of this project is to comprehensively simulate the behavior of a small diffusion flame under the influence of an externally applied electric field in zero-gravity. To date, the capability of accurately simulating electric field flames has eluded researchers because the system exhibits dramatic ranges of coupled temporal and spatial scales. Moreover, in earth gravity the hot combustion products are subject to buoyancy effects that are difficult to isolate from those generated by the electric field. This work is an implementation in an existing powerful simulation framework (PeleLM) for this problem using PeleLMeX in order to validate the model and investigate the complex coupled system. The current effort includes establishing the domain of a diffusion coflow burner, examining the boundary conditions, flame geometry and ignition with gravitational forces and also with an electric field applied. A detailed model is used that includes the chemistry of charged ions and chemiluminescent flame intermediates to capture any feedback between ion-driven convection and combustion behavior, and to allow quantitative comparisons with experimental measurements.

coflow flames↗
DOE OSTI2022

Spacecraft Geometry Effects on Kinetic Impactor Missions

Abstract The DART (Double Asteroid Redirection Test) mission will impact a spacecraft on the secondary (Dimorphos) of the binary asteroid system Didymos in 2022 September, with the goal of altering the orbital period of Dimorphos about Didymos sufficiently to be observed from ground-based observations. Numerical impact modeling is a crucial component in understanding the outcome of the DART experiment, and while many have investigated the effects of target properties, such as material strength and porosity (which remain unknown), an often overlooked factor is the importance of accurately representing the spacecraft itself in such models. Most impact modeling to date has considered simple impactor geometries such as a solid uniform sphere, but in reality the spacecraft is a complex shape full of different components, open spaces, and thin walled structures. At a minimum, a simple solid representation underestimates the surface area of the impact: for a small body such as Dimorphos (approximately 160 m in diameter), the difference between a spacecraft spanning 20 m (including solar arrays) impacting and a sub-1 m idealized shape may be important. In this paper, we compare models impacting high-fidelity models of the spacecraft based on the CAD geometry with various simplified impactors, in order to assess the potential importance of this effect. We find that the difference between the simplest impactor geometries (such as a uniform sphere) and the real spacecraft is measurable, and has an interesting dependence on the material properties of the asteroid itself.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fundamental investigation of unipolar and RF corona in atmospheric air

Here, unipolar (DC) and radio frequency (RF) corona at 3.3 MHz is studied at centimeter-sized gaps in a needle-plane geometry in atmospheric air at room temperature. Positive and negative corona using pure tungsten electrodes with varying tip angles revealed a lower onset voltage for the needle with the smaller included angle. The RF corona onset voltage and corresponding time delay were measured for a series of needles composed of pure tungsten or 2% lanthanated tungsten. The corona onset, established when the first instance of UV photon emission is detected via photomultiplier tube, occurred primarily during the negative half cycle of the applied RF voltage for pure tungsten needles. In contrast, with lanthanated tungsten needles, such preference was not observed. No distinguishable difference in onset voltage between pure tungsten and lanthanated tungsten was found, indicating that adding a small amount of lanthanum to tungsten has a negligible impact on the onset voltage at 3.3 MHz frequencies for electrodes at room temperature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Charge carrier motion and effect of fixed oxide charge in a microstructured silicon radiation detector

Signal formation in a microstructured semiconductor neutron detector is more complex than in planar diode geometry. Three-dimensional microstructures are laterally smaller than the ionization cloud length, and the electric fields may be weak enough to exhibit plasma time effects. This work is the first detailed treatment of charge carrier motion in these complex semiconductor devices to replicate the time profile and signal magnitude. Simulations were performed using COMSOL Multiphysics to investigate various parameters that affect the propagation of the charge cloud. It was observed that the size of the simulated three-dimensional structure had an impact on the induced current pulse, indicating the importance of simulation geometry optimization to accurately simulate charge cloud expansion. COMSOL Multiphysics was used to replicate accurate charge creation profiles using energy deposition information imported from radiation transport codes. A detailed simulation methodology is presented to benchmark preamplifier event pulses along with complexities in modeling the charge carrier motion along the etched microstructured trenches with Si–SiO 2 boundary conditions, including fixed oxide charge and interface trapping.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Two-dimensional isometric tensor networks on an infinite strip

The exact contraction of a generic two-dimensional (2D) tensor network state (TNS) is known to be exponentially hard, making simulation of 2D systems difficult. The recently introduced class of isometric TNS (isoTNS) represents a subset of TNS that allows for efficient simulation of such systems on finite square lattices. The isoTNS ansatz requires the identification of an “orthogonality column” of tensors, within which one-dimensional matrix product state (MPS) methods can be used for calculation of observables and optimization of tensors. Here we extend isoTNS to infinitely long strip geometries and introduce an infinite version of the Moses Move algorithm for moving the orthogonality column around the network. Using this algorithm, we iteratively transform an infinite MPS representation of a 2D quantum state into a strip isoTNS and investigate the entanglement properties of the resulting state. In addition, we demonstrate that the local observables can be evaluated efficiently. Lastly, we introduce an infinite time-evolving block decimation algorithm (iTEBD 2 ) and use it to approximate the ground state of the 2D transverse field Ising model on lattices of infinite strip geometry.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Experimental and Numerical Investigations on Dynamic Mechanical Properties of TPMS Structures

Triply Periodic Minimal Surface (TPMS) lattice structures have been of increasing interest due to their light weighting, enhanced mechanical properties, and energy absorption characteristics for automotive and biomedical applications. With the advent of additive manufacturing and geometric modeling software, TPMS lattices with complex geometries can be realized. In this work, TPMS lattice structures were fabricated with PLA using fused filament fabrication (FFF) and their dynamic properties are characterized through drop tower experiments. Although lightweight TPMS lattices are beneficial for their impact absorption capability, most of the existing works are limited to quasi-static compression and dynamic impact tests are rarely performed. The current study investigates the stress-strain and energy absorption characteristics of TPMS lattices through drop tower testing and numerical modeling. Finite element modeling for TPMS lattices is carried out to validate the experimental responses. The mechanical properties, deformation, and failure mechanisms of TPMS lattices under dynamic impact are summarized for potential future applications.

Pokkalla, Deepak↗
DOE OSTI2021

SURFACE FINISHING AND ELECTROLESS NICKEL PLATING OF ADDITIVELY MANUFACTURED (AM) METAL COMPONENTS

This study investigates the application of electroless nickel deposition on additively manufactured stainless steel samples. Current additive manufacturing (AM) technologies produce metal components with a rough surface. Rough surfaces generally exhibit fatigue characteristics, increasing the probability of initiating a crack or fracture to the printed part. For this reason, the direct use of as-produced parts in a finished product cannot be actualized, which presents a challenge. Post-processing of the AM parts is therefore required to smoothen the surface. This study analyzes chempolish (CP) and electropolish (EP) surface finishing techniques for post-processing AM stainless steel components CP has a great advantage in creating uniform, smooth surfaces regardless of size or part geometry EP creates an extremely smooth surface, which reduces the surface roughness to the sub-micrometer level. In this study, we also investigate nickel deposition on EP, CP, and as-built AM components using electroless nickel solutions. Electroless nickel plating is a method of alloy treatment designed to increase manufactured component's hardness and surface resistance to the unrelenting environment. The electroless nickel plating process is more straightforward than its counterpart electroplating.. We use low-phosphorus (2-5% P), medium-phosphorus (6-9% P), and high-phosphorus (10-13% P). These Ni deposition experiments were optimized using the L9 Taguchi design of experiments (TDOE), which compromises the prosperous content in the solution, surface finish, plane of the geometry, and bath temperature. The pre-and post-processed surface of the AM parts was characterized by KEYENCE Digital MicroscopeVHX-7000 and Phenom XL Desktop SEM. The experimental results show that electroless nickel deposition produces uniform Ni coating on the additively manufactured components up to 20 μm per hour. Mechanical properties of as-built and Ni coated AM samples were analyzed by applying a standard 10 N scratch test. Nickel coated AM samples were up to two times scratch resistant compared to the as-built samples. This study suggests electroless nickel plating is a robust viable option for surface hardening and finishing AM components for various applications and operating conditions.

Keywords: additive manufacturing, fatigue, chempol↗
DOE OSTI2021

Modulating the Surface Ligand Orientation for Stabilized Anionic Redox in Li‐Rich Oxide Cathodes

Abstract Anionic redox chemistry is emerging as a key concept in the development of high‐energy lithium‐ion batteries, as it enables a nearly doubled charge storage capacity, aiding the development of high‐capacity batteries. However, the anionic reactivity is frequently irreversible from charge to discharge, leading to rapid decay of the capacity and voltage of batteries over long‐term cycling. Although the possibility of controlling the anionic redox reactions by tuning the geometric and electronic structures has recently been proposed, the implementation of this strategy is still a critical challenge. Herein, a strategy is proposed to improve the anionic redox reversibility of a model anionic redox active cathode material, Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2 , by tuning the surface ligand geometry via the growth of a lattice‐compatible spinel LiCoO 2 coating layer on the particle surface. Detailed local structure and first principles investigations reveal that the shape and orientation of the octahedral layer in the host lattice are modified. Accordingly, a two‐band oxygen redox behavior is triggered in the ligand‐orientation‐regulated Li‐rich cathode, leading to enhanced reversibility, and thus, remarkably improved capacity and voltage retention over cycling. This study highlights the importance of controllable ligand orientation, carving a new path for the development and design of Li‐rich cathodes in the future.

Liu, Yanchen↗
DOE OSTI2020

Understanding the Origin of Highly Selective CO 2 Electroreduction to CO on Ni,N‐doped Carbon Catalysts

Abstract Ni,N‐doped carbon catalysts have shown promising catalytic performance for CO 2 electroreduction (CO 2 R) to CO; this activity has often been attributed to the presence of nitrogen‐coordinated, single Ni atom active sites. However, experimentally confirming Ni−N bonding and correlating CO 2 reduction (CO 2 R) activity to these species has remained a fundamental challenge. We synthesized polyacrylonitrile‐derived Ni,N‐doped carbon electrocatalysts (Ni‐PACN) with a range of pyrolysis temperatures and Ni loadings and correlated their electrochemical activity with extensive physiochemical characterization to rigorously address the origin of activity in these materials. We found that the CO 2 R to CO partial current density increased with increased Ni content before plateauing at 2 wt % which suggests a dispersed Ni active site. These dispersed active sites were investigated by hard and soft X‐ray spectroscopy, which revealed that pyrrolic nitrogen ligands selectively bind Ni atoms in a distorted square‐planar geometry that strongly resembles the active sites of molecular metal–porphyrin catalysts.

Koshy, David M.↗
DOE OSTI2023

Butterfly, Vinylidene-Like, Monobridged and Trans Structures of Si 2 H 2 + : Comparison to the Well-Characterized Neutral Si 2 H 2

This paper investigates four of the constitutional isomers of Si 2 H 2 + , namely the butterfly, vinylidene-like, monobridged, and trans structures. These isomer geometries were all studied using the CCSD(T) method with basis sets as large as cc-pV5Z. Higher level methods CCSDT and CCSDT(Q) were used for final energetics. It is found that the butterfly isomer has the lowest energy, followed by vinylidene-like and monobridged structures; the trans structure has the highest energy of the four. All structures were compared with their neutral counterparts. Partial charges are computed and it is found that all isomers share the positive charge between the silicon atoms. NBO analysis shows that the cation Si-Si bond order is reduced by 0.5 relative to the neutral versions of the same isomer in the case of the butterfly, vinylidene-like, and monobridged; and reduced by 0.6 for the trans isomer. Vibrational frequencies, infrared intensities, and dipole moments are predicted to encourage the spectroscopic identification of Si 2 H 2 + .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Cutting edge research and new technologies in heat and mass transfer processes of refrigeration and air conditioning systems

This special edition of the Science and Technology for the Built Environment (STBE) presents eight selected articles originally presented at the 17th International Refrigeration and Air Conditioning Conference held at Purdue University, West Lafayette, IN, USA, during July 9–12, 2018. All eight articles were significantly expanded with additional technical content and received full peer review before being finally accepted for publication in this special issue of the STBE. The eight articles in this special issue cover a wide range of topics from condensation and evaporation of low global warming potential (LGWP) refrigerants to phase change material storage for personal cooling systems, from frosting on hydrophilic and hydrophobic coated surfaces to geometry optimization of heat exchanger fins. Furthermore, these articles describe cutting-edge research and feasibility studies of new technologies that were recently investigated for refrigeration and air conditioning applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Optimization Methodology of Polar Direct-Drive Illumination for the National Ignition Facility

Improved laser illumination uniformity drives shocks and implosions to create more extreme high energy density environments. Predominantly, the geometry of experiments that can be performed is dictated by the layout of beams at laser facilities, limiting inter-facility and multiscale investigations. This Letter presents the first automated, algorithmic approach for generating illumination configurations for high energy density experiments. The method is demonstrated in comparison to a polar direct drive solid target experiment at the National Ignition Facility. The new illumination configuration is simulated to create greater than ×3 higher peak pressure and almost ×2 higher density by maintaining better shock uniformity. Furthermore, the optimization process is performed with reduced computational expense and isotropic plasma profiles, while accounting for the impact of cross-beam energy transfer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗