SEARCH · Search NASA

Results for “high speed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Flexible High Speed Codec (FHSC)

The ongoing NASA/Harris Flexible High Speed Codec (FHSC) program is described. The program objectives are to design and build an encoder decoder that allows operation in either burst or continuous modes at data rates of up to 300 megabits per second. The decoder handles both hard and soft decision decoding and can switch between modes on a burst by burst basis. Bandspreading is low since the code rate is greater than or equal to 7/8. The encoder and a hard decision decoder fit on a single application specific integrated circuit (ASIC) chip. A soft decision applique is implemented using 300 K emitter coupled logic (ECL) which can be easily translated to an ECL gate array.

Segallis, G. P.↗

NASA NTRS2001

Coupled Aerodynamic and Structural Sensitivity Analysis of a High-Speed Civil Transport

An objective of the High Performance Computing and Communication Program at the NASA Langley Research Center is to demonstrate multidisciplinary shape and sizing optimization of a complete aerospace vehicle configuration by using high-fidelity, finite-element structural analysis and computational fluid dynamics aerodynamic analysis. In a previous study, a multi-disciplinary analysis system for a high-speed civil transport was formulated to integrate a set of existing discipline analysis codes, some of them computationally intensive, This paper is an extension of the previous study, in which the sensitivity analysis for the coupled aerodynamic and structural analysis problem is formulated and implemented. Uncoupled stress sensitivities computed with a constant load vector in a commercial finite element analysis code are compared to coupled aeroelastic sensitivities computed by finite differences. The computational expense of these sensitivity calculation methods is discussed.

Mason, B. H.↗

NASA NTRS1942

Preliminary Results of Flight Tests of a Conventional Three-Blade Propeller at High Speeds

As part of the program of flight tests of airplane propellers to determine compressibility effects at high speeds, preliminary flights have been made with a conventional three-blade propeller (Hamilton Standard 3155-6) on a Bell YP-39 airplane. This preliminary report presents the high-speed data obtained thus far with a brief analysis of the results.

Vogeley, A. W.↗

NASA NTRS1991

Formal specification of a high speed CMOS correlator

The formal specification of a high speed CMOS correlator is presented. The specification gives the high-level behavior of the correlator and provides a clear, unambiguous description of the high-level architecture of the device.

Windley, P. J.↗

NASA NTRS1990

NASA Langley and AF RADC high-speed fiber optic transceiver program

NASA-Langley and the USAF Rome Air Development Center have been pursuing the development of military- and space-qualified fiber optic transceivers for a variety of ground-based, space-based, and general avionic applications. An initial development pursued a design called the multipurpose fiber optic transceiver (MFOX) and provided a family of fiber optic transceivers which operated up to 1 Gb/s. Currently, a second generation of high-speed fiber optic transceivers (HSFOX) is being developed. This design will utilize an all-integrated-circuits approach in order to develop a lighter-weight, smaller-size, and more efficient transceiver. The high-speed fiber optic transceiver will be military-and-space-operating in the 0.05-5 Gb/s data rate range. The initial results of tests, performance, and availability of commercial high-speed all-integrated-circuit chipsets for fiber-optic transceivers are discussed, as well as the performance of transceivers fabricated from these chipsets.

Hendricks, Herbert D.↗

NASA NTRS1982

High-speed machining of space shuttle External Tank (ET) panels

The applicability to and advantages of the high-speed machining process for the production of Space Shuttle external tank panels by physically machining selected sample portions of an external tank panel were investigated. The panel sample configuration was selected, and potential high speed milling procedures identified. An 8 foot long panel was machined and the milling demonstration is described in detail.

Miller, J. A.↗

NASA NTRS1925

Aerodynamic Characteristics of Airfoils at High Speeds

This report deals with an experimental investigation of the aerodynamical characteristics of airfoils at high speeds. Lift, drag, and center of pressure measurements were made on six airfoils of the type used by the air service in propeller design, at speeds ranging from 550 to 1,000 feet per second. The results show a definite limit to the speed at which airfoils may efficiently be used to produce lift, the lift coefficient decreasing and the drag coefficient increasing as the speed approaches the speed of sound. The change in lift coefficient is large for thick airfoil sections (camber ratio 0.14 to 0.20) and for high angles of attack. The change is not marked for thin sections (camber ratio 0.10) at low angles of attack, for the speed range employed. At high speeds the center of pressure moves back toward the trailing edge of the airfoil as the speed increases. The results indicate that the use of tip speeds approaching the speed of sound for propellers of customary design involves a serious loss in efficiency.

Briggs, L J↗

NASA NTRS1991

Engine technology challenges for a 21st century high speed civil transport

Recent NASA funded studies by Boeing and Douglas suggest an opportunity exists for a 21st Century High Speed Civil Transport (HSCT) to become part of the international air transportation system. However, before this opportunity for high speed travel can be realized, certain environmental and and economic barrier issues must be overcome. These challenges are outlined. Research activities which NASA has planned to address these barrier issues and to provide a technology base to allow U.S. manufacturers to make an informed go/no go decision on developing the HSCT are discussed.

Shaw, Robert J.↗

NASA NTRS1990

NASA. Lewis Research Center/IFMD inlet duct and nozzle high speed validation experiments

Personnel from NASA Lewis Research Center spoke on the subject of inlet duct and nozzle high speed validation experiments to include crossing shocks and boundary layer interaction, unsteady shock/boundary layer interactions, and vortex generators. Attention was also paid to the subjects of high speed mixing and transition ducts. Specific application was made to the NASP hypermixing concepts.

Hingst, Warren↗

NASA NTRS1979

Computer-assisted high-speed balancing of T53 and T55 power turbines

Standard overhaul procedures for U.S. Army helicopter engines require operational vibration acceptance testing after rebuild. Engines frequently experience vibrations which exceed allowable overhaul work requirement limits. The rework/retest cycle for these engines constitute a significant cost penalty to the overhaul center. This paper reviews both analytical and test data which indicate bending critical speeds within the operating speed range of the low-speed power turbine rotor as the cause of most test cell rejections. High-speed balancing techniques are applicable and are capable of significantly reducing this reject rate. A complete prototype computer-assisted high-speed balancing system for assembled T53 and T55 power turbine rotors is described.

Pojeta, T. J.↗

NASA NTRS1989

A prediction of high-speed rotor noise

A combined computational (CFD) and integral approach solves the acoustic pressure fields of two high-speed helicopter rotors. A CFD code supplies boundary data to a non-linear type of Kirchhoff integral formulation to find the far-field pressures. Direct calculations of pressures are given by the CFD code up to the sonic cylinder where the Kirchhoff method takes over. This paper shows predictions and measurements of High-Speed Impulsive (HSI) noise in hover for two different rotor geometries. One rotor has a conventional rectangular planform, while the other rotor is highly swept and tapered. The swept rotor analysis forms the majority of this paper. Test data from both rotors are shown and compared with predictions for a range of tip Mach numbers from .85 to .95 (including delocalization). The correlation with the near-field pressures from the straight bladed experiment is excellent and good to excellent correlation is seen for the far-field pressures from both experiments.

Purcell, Timothy W.↗

NASA NTRS1992

Parametric studies for tiltrotor aeroelastic stability in high-speed flight

The influence of several system design parameters on tiltrotor aeroelastic stability is examined for the high-speed (axial) flight mode. Coupling of the rotor flapping modes with the wing elastic modes produces a whirl motion, typical of tiltrotors, that can become unstable at high speeds. The sensitivity of this instability with respect to rotor frequencies, wing stiffness, forward wing sweep, and rotor thrust level is examined. Some important new trends are identified regarding the role of blade lag dynamics and forward wing sweep in tiltrotor aeroelastic stability. The blade lag frequency may be tuned to improve tiltrotor stability, and forward wing sweep is destabilizing because of changes in rotor force components associated with the sweep.

Nixon, Mark W.↗

NASA NTRS1977

High-speed computerized tomography

The development of a high-speed reconstruction processor and a channelized architecture to use with a high-resolution tomographic unit is discussed with attention to the convolution reconstruction algorithm. By means of this algorithm, input data and intermediate result precision required throughout the algorithm execution have been studied with computer simulation using profile data derived from mathematically simulated test objects and experimental animal data. A prototype section for a highly parallel all-digital system executes 60 million arithmetic operations per second, and the full-scale version is expected to reconstruct 500 to 1000 cross sections per second.

Swartzlander, E. E., Jr.↗

NASA NTRS1992

High speed research system study. Advanced flight deck configuration effects

In mid-1991 NASA contracted with industry to study the high-speed civil transport (HSCT) flight deck challenges and assess the benefits, prior to initiating their High Speed Research Program (HSRP) Phase 2 efforts, then scheduled for FY-93. The results of this nine-month effort are presented, and a number of the most significant findings for the specified advanced concepts are highlighted: (1) a no nose-droop configuration; (2) a far forward cockpit location; and (3) advanced crew monitoring and control of complex systems. The results indicate that the no nose-droop configuration is critically dependent upon the design and development of a safe, reliable, and certifiable Synthetic Vision System (SVS). The droop-nose configuration would cause significant weight, performance, and cost penalties. The far forward cockpit location, with the conventional side-by-side seating provides little economic advantage; however, a configuration with a tandem seating arrangement provides a substantial increase in either additional payload (i.e., passengers) or potential downsizing of the vehicle with resulting increases in performance efficiencies and associated reductions in emissions. Without a droop nose, forward external visibility is negated and takeoff/landing guidance and control must rely on the use of the SVS. The technologies enabling such capabilities, which de facto provides for Category 3 all-weather operations on every flight independent of weather, represent a dramatic benefits multiplier in a 2005 global ATM network: both in terms of enhanced economic viability and environmental acceptability.

Swink, Jay R.↗

NASA NTRS1999

First NASA/Industry High-Speed Research Configuration Aerodynamics Workshop

This publication is a compilation of documents presented at the First NASA/Industry High Speed Research Configuration Aerodynamics Workshop held on February 27-29, 1996 at NASA Langley Research Center. The purpose of the workshop was to bring together the broad spectrum of aerodynamicists, engineers, and scientists working within the Configuration Aerodynamics element of the HSR Program to collectively evaluate the technology status and to define the needs within Computational Fluid Dynamics (CFD) Analysis Methodology, Aerodynamic Shape Design, Propulsion/Airframe Integration (PAI), Aerodynamic Performance, and Stability and Control (S&C) to support the development of an economically viable High Speed Civil Transport (HSCT) aircraft. To meet these objectives, papers were presented by representative from NASA Langley, Ames, and Lewis Research Centers; Boeing, McDonnell Douglas, Northrop-Grumman, Lockheed-Martin, Vigyan, Analytical Services, Dynacs, and RIACS.

Wood, Richard M.↗

NASA NTRS1999

First NASA/Industry High-Speed Research Configuration Aerodynamics Workshop

Wood, Richard M.↗

NASA NTRS2011

Miniature high speed compressor having embedded permanent magnet motor

A high speed centrifugal compressor for compressing fluids includes a permanent magnet synchronous motor (PMSM) having a hollow shaft, the being supported on its ends by ball bearing supports. A permanent magnet core is embedded inside the shaft. A stator with a winding is located radially outward of the shaft. The PMSM includes a rotor including at least one impeller secured to the shaft or integrated with the shaft as a single piece. The rotor is a high rigidity rotor providing a bending mode speed of at least 100,000 RPM which advantageously permits implementation of relatively low-cost ball bearing supports.

Zhou, Lei↗

NASA NTRS1981

Supersonic stall flutter of high-speed fans

An analytical model is proposed for predicting the onset of supersonic stall bending flutter in high-speed rotors. The analysis is based on a modified two-dimensional, compressible, unsteady actuator disk theory. The stability boundary predicted by the analysis is shown to be in good agreement with the measured boundary of a high speed fan. The prediction that the flutter mode would be a forward traveling wave sensitive to wheel speed and aerodynamic loading is confirmed by experimental measurements. In addition, the analysis shows that reduced frequency and dynamic head also play a significant role in establishing the supersonic stall bending flutter boundary of an unshrouded fan.

Adamczyk, J. J.↗