Search NASA⌕ Search

SEARCH · Search NASA

Results for “impacter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Influence of Temperature and Impact Velocity on the Coefficient of Restitution

Tests were performed on a variety of material combinations to understand the effects of temperature and impact velocity on the coefficient of restitution (COR). The tests, performed in a vacuum at room and liquid nitrogen temperatures, consisted of dropping a ball onto a target plate and recording the impact time history of the ball's bounce-down. Time intervals between successive impacts were measured from the time history and used to calculate the coefficient of restitution and impact velocity for each impact. Maximum impact velocities ranged from approximately 33 (0.84) to 52 in./s (1.32 m/s). Five ball-target plate combinations were evaluated: type 316 stainless steel (316 SS) on 316 SS; M50 tool steel on Armalon; M50 on 4340 steel; 410C steel on Armalon; and copper on copper. The coefficient of restitution for the 316 SS-316 SS, M50-Armalon, 410C-Armalon, and copper-copper combinations increased as the temperature and impact velocity decreased. The coefficient for the hard steel combination, M50-4340, was not greatly influenced by temperature or variations in impact velocity.

Radil, Kevin C.↗
NASA NTRS1995

Hypervelocity impact survivability experiments for carbonaceous impactors, part 2

Hypervelocity impact experiments were performed to further test the survivability of carbonaceous impactors and to determine potential products that may have been synthesized during impact. Diamonds were launched by the Ames two-stage light gas gun into Al plate at velocities of 2.75 and 3.1 km sec(exp -1). FESEM imagery confirms that diamond fragments survived in both experiments. Earlier experiments found that diamonds were destroyed on impact above 4.3 km sec(exp -1). Thus, the upper stability limit for diamond on impact into Al, as determined from our experimental conditions, is between 3.1 and 4.3 km sec(exp -1). Particles of the carbonaceous chondrite Nogoya were also launched into Al at a velocity of 6.2 km sec (exp -1). Laser desorption (L (exp 2) MS) analyses of the impactor residues indicate that the lowest and highest mass polycyclic aromatic hydrocarbons (PAH's) were largely destroyed on impact; those of intermediate mass (202-220 amu) remained at the same level or increased in abundance. In addition, alkyl-substituted homologs of the most abundant pre-impacted PAH's were synthesized during impact. These results suggest that an unknown fraction of some organic compounds can survive low to moderate impact velocities and that synthesized products can be expected to form up to velocities of, at least, 6.5 km sec(exp -1). We also present examples of craters formed by a unique microparticle accelerator that could launch micron-sized particles of almost any coherent material at velocities up to approximately 15 km sec(exp -1). Many of the experiments have a direct bearing on the interpretation of LDEF craters.

Bunch, T. E.↗
NASA NTRS1995

Secondary ion mass spectrometry (SIMS) analysis of hypervelocity microparticle impact sites on LDEF surfaces

Two dimensional elemental ion maps have been recorded for hundreds of microparticle impact sites and contamination features on LDEF surfaces. Since the majority of the analyzed surfaces were metal-oxide-silicon (MOS) impact detectors from the Interplanetary Dust Experiment, a series of 'standard' and 'blank' analyses of these surfaces are included. Hypervelocity impacts of forsterite olivine microparticles on activated flight sensors served as standards while stylus and pulsed laser simulated 'impacts' served as analytical blanks. Results showed that despite serious contamination issues, impactor residues can be identified in greater than 1/3 of the impact sites. While aluminum oxide particles could not be detected on aluminum surfaces, they were detected on germanium surfaces from row 12. Remnants of manmade debris impactors consisting of paint chips and bits of metal were identified on surfaces from LDEF Rows 3 (west or trailing side), 6 (south), 9 (ram or leading side), 12 (north) and the space end. Higher than expected ratios of manmade microparticle impacts to total microparticle impacts were found on the space end and the trailing side. These results were consistent with time-tagged and time-segregated microparticle impact data from the IDE and other LDEF experiments. A myriad of contamination interferences were identified and their effects on impactor debris identification mitigated during the course of this study. These interferences include pre-, post and inflight deposited surface contaminants as well as indigenous heterogeneous material contaminants. Non-flight contaminations traced to human origins, including spittle and skin oils, contributed significant levels of alkali-rich carbonaceous interferences. A ubiquitous layer of in-flight deposited silicaceous contamination varied in thickness with location on LDEF, even on a micro scale. In-flight deposited (low velocity) contaminants include urine droplets and bits of metal film from eroded thermal blankets.

Simon, C. G.↗
NASA NTRS1997

Impact Cratering Calculations

Understanding the physical processes of impact cratering on planetary surfaces and atmospheres as well as collisions of finite-size self-gravitating objects is vitally important to planetary science. The observation has often been made that craters are the most ubiquitous landform on the solid planets and the satellites. The density of craters is used to date surfaces on planets and satellites. For large ringed basin craters (e.g. Chicxulub), the issue of identification of exactly what 'diameter' transient crater is associated with this structure is exemplified by the arguments of Sharpton et al. (1993) versus those of Hildebrand et al. (1995). The size of a transient crater, such as the K/T extinction crater at Yucatan, Mexico, which is thought to be the source of SO,-induced sulfuric acid aerosol that globally acidified surface waters as the result of massive vaporization of CASO, in the target rock, is addressed by our present project. The impact process excavates samples of planetary interiors. The degree to which this occurs (e.g. how deeply does excavation occur for a given crater diameter) has been of interest, both with regard to exposing mantle rocks in crater floors, as well as launching samples into space which become part of the terrestrial meteorite collection (e.g. lunar meteorites, SNC's from Mars). Only in the case of the Earth can we test calculations in the laboratory and field. Previous calculations predict, independent of diameter, that the depth of excavation, normalized by crater diameter, is d(sub ex)/D = 0.085 (O'Keefe and Ahrens, 1993). For Comet Shoemaker-Levy 9 (SL9) fragments impacting Jupiter, predicted excavation depths of different gas-rich layers in the atmosphere, were much larger. The trajectory and fate of highly shocked material from a large impact on the Earth, such as the K/T bolide is of interest. Melosh et al. (1990) proposed that the condensed material from the impact upon reentering the Earth's atmosphere induced. radiative heating, and producing global firestorms. The observed reentry splash of the SL-9 impact-induced plumes that reimpact Jupiter (Boslough et al., 1994) supported Melosh's K/T model. The fate of early primitive planetary atmospheres during the latter stages of planetary accretion, resulting from impactors in the 100 to 103 km diameter require modeling, e.g. Newman et al. (1997). Ahrens (1990; 1993) and Chen and Ahrens (1997) found that upon delivery of most of the impact energy to the solid planet, very large ground motions arise, which couple sufficient kinetic energy to the atmosphere to cause substantial atmospheric escape. The trade-off of this model with that of Cameron (1997) who suggests that atmospheric blow-off occurs as a result of the massive impact-induced heating of the atmosphere and Pepin (1997) who uses this heating event to model differential hydrodynamic loss of lighter atmospheric gases, requires further research.

Ahrens, Thomas J.↗
NASA NTRS1998

Traces of Catastrophe: A Handbook of Shock-Metamorphic Effects in Terrestrial Meteorite Impact Structures

This handbook of Shock-Metamorphic Effects in Terrestrial Meteorite Impact Structures emphasizes terrestrial impact structures, field geology, and particularly the recognition and petrographic study of shock-metamorphic effects in terrestrial rocks. Individual chapters include: 1) Landscapes with Craters: Meteorite Impacts, Earth, and the Solar System; 2) Target Earth: Present, Past and Future; 3) Formation of Impact Craters; 4) Shock-Metamorphic Effects in Rocks and Minerals; 5) Shock-Metamorphosed Rocks (Impactities) in Impact Structures; 6) Impact Melts; 7) How to Find Impact Structures; and 8) What Next? Current Problems and Future Investigations.

French, Bevan M.↗
NASA NTRS2000

Ignition Resistance of Polymeric Materials to Particle Impact in High-Pressure Oxygen

Particle impact ignition has been the primary cause of numerous fires in oxygen systems. This ignition phenomenon is known to occur where particles are present in high-velocity gas, and where impact occurs on a flammable material. The particle impact ignition behavior of many metals has been widely studied, but the particle impact ignition behavior of polymeric materials is relatively unknown. Particle impact ignition in polymeric materials is a concern as these materials are commonly used in component seat and seal applications, where high-velocity particle impacts can occur. This study evaluates several polymeric materials and compares the minimum temperature required for ignition (threshold temperature) of these materials: Kel-F 81 (CTFE), Teflon (PTFE), PEEK, Vespel SP-21, and Nylon 6/6. The materials were configured as targets in the White Sands Test Facility high-velocity particle impact test system. Gaseous oxygen was flowed at 4000 psi and sonic velocity, and the targets were impacted with 2000-micron aluminum 2017 particles. This paper discusses the results of these tests and ranks the materials according to their threshold temperatures at these conditions.

Forsyth, Elliot T.↗
NASA NTRS2000

A Comparison of Quasi-Static Indentation to Low-Velocity Impact

A static test method for modeling low-velocity foreign object impact events to composites would prove to be very beneficial to researchers since much more data can be obtained from a static test than from an impact test. In order to examine if this is feasible, a series of static indentation and low-velocity impact tests were carried out and compared. Square specimens of many sizes and thicknesses were utilized to cover the array of types of low velocity impact events. Laminates with a pi/4 stacking sequence were employed since this is by far the most common type of engineering laminate. Three distinct flexural rigidities -under two different boundary conditions were tested in order to obtain damage ranging from that due to large deflection to contact stresses and levels in-between to examine if the static indentation-impact comparisons are valid under the spectrum of damage modes that can be experienced. Comparisons between static indentation and low-velocity impact tests were based on the maximum applied transverse load. The dependent parameters examined included dent depth, back surface crack length, delamination area, and to a limited extent, load-deflection behavior. Results showed that no distinct differences could be seen between the static indentation tests and the low-velocity impact tests, indicating that static indentation can be used to represent a low-velocity impact event.

Nettles, A. T.↗
NASA NTRS2000

Ultrasonic Assessment of Impact-Induced Damage and Microcracking in Polymer Matrix Composites

The main objective of this NASA FAR project is to conduct ultrasonic assessment of impact-induced damage and microcracking in polymer matrix composites at various temperatures. It is believed that the proposed study of impact damage assessment on polymer matrix composites will benefit several NASA's missions and current interests, such as ballistic impact testing of composite fan containment and high strain rate deformation modeling of polymer matrix composites. Currently, impact-induced delamination and fracture in 6061-T6 aluminum/cast acrylic sandwich plates adhered by epoxy were generated in an instrumented drop-weight impact machine. Although only a small dent was produced on the aluminum side when a hemispherical penetrator tup was dropped onto it from a couple of inches, a large ring of delamination at the interface was observed. The delamination damage was often accompanied by severe shattering in the acrylic substratum. Damage patterns in the acrylic layer include radial and ring cracks and, together with delamination at the interface, may cause peeling-off of acrylic material from the sandwich plate. Theory of stress-wave propagation can be used to explain these damage patterns. The impact tests were conducted at various temperatures. The results also show clearly that temperature effect is very important in impact damage. For pure cast acrylic nil-ductile transition (NDT) occurs between 185-195 F Excessive impact energy was dissipated into fracture energy when tested at temperature below this range or through plastic deformation when tested at temperature above the NDT temperature. Results from this study will be used as baseline data for studying fiber-metal laminates, such as GLARE and ARALL for advanced aeronautical and astronautical applications.

Liaw, Benjamin↗
NASA NTRS2001

A Comparison of Quasi-Static Indentation Testing to Low Velocity Impact Testing

The need for a static test method for modeling low-velocity foreign object impact events to composites would prove to be very beneficial to researchers since much more data can be obtained from a static test than from an impact test. In order to examine if this is feasible, a series of static indentation and low velocity impact tests were carried out and compared. Square specimens of many sizes and thickness were utilized to cover the array of types of low velocity impact events. Laminates with a n/4 stacking sequence were employed since this is by the most common type of engineering laminate. Three distinct flexural rigidities under two different boundary conditions were tested in order to obtain damage due to large deflections, contact stresses and both to examine if the static indentation-impact comparisons are valid under the spectrum of damage modes that can be experienced. Comparisons between static indentation and low velocity impact tests were based on the maximum applied transverse load. The dependent parameters examined included dent depth, back surface crack length, delamination area and to a limited extent, load-deflection behavior. Results showed that no distinct differences could be seen between the static indentation tests and the low velocity impact tests, indicating that static indentation can be used to represent a low velocity impact event.

Nettles, Alan T.↗
NASA NTRS1994

The Contemporary Hazard of Cometary Impacts

Cosmic impacts pose a continuing hazard of loss of human life and property. Significant contemporary risk is associated with projectiles in the energy range from about 10 megatons of TNT up to the size of the K/T impactor. The lower threshold for damage is defined by the atmosphere of the Earth, which effectively shields us From smaller projectiles. Up to energies of about a gigaton of TNT, the effects are local or regional for impacts on the land, or coastal for ocean impacts, which can generate large tsunamis. A greater risk is associated with still larger impacts, which are capable of causing global ecological catastrophe, possibly leading to mass mortality From starvation and epidemics. If such a impact took place anywhere on Earth during our lifetimes, we would each be in danger, independent of where the projectile struck. Statistical estimates indicate that each human on this planet runs a risk of roughly 1 in 20,000 of dying from this cause. Prudence suggests that we should be concerned about such impacts and seek ways of avoiding them or mitigating their consequences. The primary objective of any program to deal with this hazard is to determine whether or not such a near-term impact is likely. The best approach for the asteroidal component is a comprehensive telescopic survey, which can discover all Earth-crossing asteroids larger than 1 km in diameter and provide decades of warning in which to plan ways to deflect or destroy a threatening object. Long-period comets, however, pose a much greater challenge, since they cannot be discovered long in advance of a possible impact, their orbits are harder to predict, and they are significantly more difficult to deflect or destroy.

Morrison, David↗
NASA NTRS1994

Impacts with the Earth and Jupiter

The Earth has been subject to impacts from comets and asteroids since its formation, and such impacts have played an important role in the evolution of life on our planet. We now recognize not only the historical role of impacts, but the contemporary hazard posed by such events. In the absence of a complete census of potentially threatening Earth-crossing asteroids or comets (called collectively Near Earth Objects, or NEOs), or even of a comprehensive current search program to identify NEOs, we can consider the hazard only from a probabilistic perspective. In general, the larger the object the greater the hazard, even when allowance is made for the infrequency of large impacts. Most of the danger to human life is associated with impacts by objects roughly 2 km or larger (energy greater than 1 million megatons), which can inject sufficient submicrometer dust into the atmosphere to produce a severe short-term global cooling with subsequent loss of crops, leading to starvation. Hazard estimates suggest that the chance of such an event occurring during a human lifetime is about 1:5000, and the global probability of death from such impacts is of the order of 1:20000, values that can be compared with risks associated with other natural hazards such as earthquakes, volcanic eruptions, and severe storms. The widely-observed impact of Comet Shoemaker-Levy 9 with Jupiter in July 1994 provides a graphic example of such an interplanetary collision and is stimulating worldwide interest in protecting our planet against cosmic impact catastrophes.

Morrison, David↗
NASA NTRS1994

The Impact Hazard

The Earth has been subject to hypervelocity impacts from comets and asteroids since its formation, and such impacts have played an important role in the evolution of life on our planet. We now recognize not only the historical role of impacts, but the contemporary hazard posed by such events. In the absence of a complete census of potentially threatening Earth-crossing asteroids or comets (called collectively Near Earth Objects, or NEOs), or even of a comprehensive cur-rent search program to identify NEOs, we can consider the hazard only from a probabilistic perspective. We know the steep power-law relationship between NEO numbers and size, with many more small bodies than large ones. We also know that few objects less than about 50 m in diameter (with kinetic energy near 10 megatons) penetrate the atmosphere and are capable of doing surface damage. But there is a spectrum of possible impact hazards associated with objects from this 10-megaton threshold all the way up to NEOs 5 km or larger in diameter, which are capable of inflicting severe damage on the environment, leading to mass extinction's of species. Detailed analysis has shown that, in general, the larger the object the greater the hazard, even when allowance is made for the infrequency of large impacts. Most of the danger to human life is associated with impacts by objects roughly 2 km or larger (energy greater than 1 million megatons), which can inject sufficient submicrometer dust into the atmosphere to produce a severe short-term global cooling with subsequent loss of crops, leading to starvation. Hazard estimates suggest that the chance of such an event occurring during a human lifetime is about 1:5000, and the global probability of death from such impacts is of the order of 1:20000, values that can be compared with risks associated with other natural hazards such as earthquakes, volcanic eruptions, and severe storms. However, the impact hazard differs from the others in that it can be largely prevented by a comprehensive survey for threatening objects and the application of technological solutions to deflect or destroy objects that are found to have orbits that will lead to collision with the Earth.

Morrison, David↗
NASA NTRS1999

Ejecta Pattern of the Impact of Comet Shoemaker-Levy 9

The collision of Comet Shoemaker-Levy 9 (SL 9) with Jupiter created crescent-shaped ejecta patterns around impact sites. Although the observed impact plumes rose through a similar height of approx.3000 km, the radii of the created ejects patterns differ from impact to impact and generally are larger for larger impacts. The azimuthal angle of the symmetry axis of the ejects pattern is larger than that predicted by the models of oblique impacts, due to the action of the Coriolis force that rotates ejecta patterns counterclockwise from the south. We study the formation of ejects patterns using a simple model of ballistic plume above a rotating plane. The ejected particles follow ballistic trajectories and slide horizontally for about an hour after reentry into the jovian atmosphere. The lateral expansion of the plume is stopped by the friction force, which is assumed to be proportional to the square of the horizontal velocity. Two different mass-velocity distributions used in the simulations produce qualitatively similar results. The simulated ejecta patterns fit very well the "crescents" observed at the impact sites. The sizes and azimuthal angles of symmetry axis of ejects patterns depend on a parameter L, which has dimension of length and is related to the mass of the fragment. Thus more massive impacts produce larger ejects patterns that are rotated through a wider angle.

Pankine, Alexey A.↗
NASA NTRS2003

Size Effects in Impact Damage of Composite Sandwich Panels

Panel size has a large effect on the impact response and resultant damage level of honeycomb sandwich panels. It has been observed during impact testing that panels of the same design but different panel sizes will show large differences in damage when impacted with the same impact energy. To study this effect, a test program was conducted with instrumented impact testing of three different sizes of sandwich panels to obtain data on panel response and residual damage. In concert with the test program. a closed form analysis method was developed that incorporates the effects of damage on the impact response. This analysis method will predict both the impact response and the residual damage of a simply-supported sandwich panel impacted at any position on the panel. The damage is incorporated by the use of an experimental load-indentation curve obtained for the face-sheet/honeycomb and indentor combination under study. This curve inherently includes the damage response and can be obtained quasi-statically from a rigidly-backed specimen or a specimen with any support conditions. Good correlation has been obtained between the test data and the analysis results for the maximum force and residual indentation. The predictions can be improved by using a dynamic indentation curve. Analyses have also been done using the MSC/DYTRAN finite element code.

Dobyns, Alan↗
NASA NTRS2003

Spherule Beds 3.47-3.24 Billion Years Old in the Barberton Greenstone Belt, South Africa: A Record of Large Meteorite Impacts and Their Influence on Early Crustal and Biological Evolution

Four layers, S1-S4, containing sand-sized spherical particles formed as a result of large meteorite impacts, occur in 3.47-3.24 Ga rocks of the Barberton Greenstone Belt, South Africa. Ir levels in S3 and S4 locally equal or exceed chondritic values but in other sections are at or only slightly above background. Most spherules are inferred to have formed by condensation of impact-produced rock vapor clouds, although some may represent ballistically ejected liquid droplets. Extreme Ir abundances and heterogeneity may reflect element fractionation during spherule formation, hydraulic fractionation during deposition, and/or diagenetic and metasomatic processes. Deposition of S1, S2, and S3 was widely influenced by waves and/or currents interpreted to represent impact-generated tsunamis, and S1 and S2 show multiple graded layers indicating the passage of two or more wave trains. These tsunamis may have promoted mixing within a globally stratified ocean, enriching surface waters in nutrients for biological communities. S2 and S3 mark the transition from the 300-million-year-long Onverwacht stage of predominantly basaltic and komatiitic volcanism to the late orogenic stage of greenstone belt evolution, suggesting that regional and possibly global tectonic reorganization resulted from these large impacts. These beds provide the oldest known direct record of terrestrial impacts and an opportunity to explore their influence on early life, crust, ocean, and atmosphere. The apparent presence of impact clusters at 3.26-3.24 Ga and approx. 2.65-2.5 Ga suggests either spikes in impact rates during the Archean or that the entire Archean was characterized by terrestrial impact rates above those currently estimated from the lunar cratering record.

Lowe, Donald R.↗
NASA NTRS2001

Exploration of the Eltanin Impact Area (Bellingshausen Sea): Expedition ANT XVIII5a

The impact of the Eltanin asteroid into the Bellingshausen Sea (2.15 Ma) is the only known impact in a deep-ocean (approx. 5 km) basin. On 26 March 2001, the FS Polarstern returned to the impact area during expedition ANT XVIII/5a. Over a period of 14 days, this region was explored by detailed bathymetric mapping, acoustic profiling of sediment deposits, and direct sampling with 18 piston cores and four gravity cores. Preliminary shipboard examination of microfossils showed that sixteen of the piston cores and three gravity cores contained sediments at least as old as the impact event and have a high probability of containing a record of the disturbances caused by the impact. During the expedition, portions of eleven piston cores were opened for preliminary examination of the impact deposits. Visual examination of cores and microscopic identification of suspect impact melt particles were were used to identify ejecta and X-ray radiographs of the opened core segments permitted analysis of sediment structures. Impact deposits were found in nine of the eleven opened cores, and a similar success rate is anticipated in the seven cores remaining to be opened. These preliminary observations indicate that the highest concentrations of meteoritic ejecta and the largest particle sizes appear to occur in the region north of the San Martin seamounts. Recovered debris includes cm-sized melt rocks and a 2.5 cm meteorite. This expedition has confirmed the presence of high concentrations of meteoritic ejecta across a region at least as large as 10(exp 5) sq km. Quantitative analyses of ejecta distribution within this region will require further study, but previous estimates of 1 km for the minimum diameter of the Eltanin asteroid, appear safe.

Gersonde, Rainer↗
NASA NTRS2003

Ejecta from Ocean Impacts

Numerical simulations of deep-ocean impact provide some limits on the size of a projectile that will not mix with the ocean floor during a deep-ocean impact. For a vertical impact at asteroidal velocities (approx. 20 km/s), mixing is only likely when the projectile diameter is greater than 112 of the water depth. For oblique impacts, even larger projectiles will not mix with ocean floor silicates. Given the typical water depths of 4 to 5 km in deep-ocean basins, asteroidal projectiles with diameters as large as 2 or 3 km may commonly produce silicate ejecta that is composed only of meteoritic materials and seawater salts. However, the compressed water column beneath the projectile can still disrupt and shock metamorphose the ocean floor. Therefore, production of a separate, terrestrial ejecta component is not ruled out in the most extreme case. With increasing projectile size (or energy) relative to water depths, there must be a gradation between oceanic impacts and more conventional continental impacts. Given that 60% of the Earth's surface is covered by oceanic lithosphere and 500 m projectiles impact the Earth on 10(exp 5) y timescales, there must be hundreds of oceanic impact deposits in the sediment record awaiting discovery.

Kyte, Frank T.↗
NASA NTRS2003

Osmium Isotope Constraints on the Proportion of Bolide Component in Chicxulub Impact Melts

Recent drilling has produced the samples of impact melt breccias examined here. All samples examined here are from the YAX-1 borehole [7]. Two main types of impact breccias have been studied. The first type is a green altered impact meltrock found in the lower portion of the impact sequence. The texture of the rock is microcrystalline and is composed of pyroxene, plagioclase, and alkali feldspars. Its composition is consistent with continental margin rocks. It is generally massive with some flow structure. The rock was brecciated and altered after solidfication and contains small amounts of both shocked and unshocked clasts of the impacted lithologies. These lithologies include lithic quartzite, and isolated feldspar crystals. The compositions of these rocks are similar to those seen in meltrocks sampled by the Yucatan-6 borehole [8-9]. Our study includes samples YAX-1_861.4, YAX-1_863.51, and YAX- 1_876.46, which represent both the top and lower portion of the green impact meltrock. The middle sample in the sequence has the least amount of (mineralogical) alteration [10]. The second type of melt breccia under study is a brown altered impact meltrock. It also has a microcrystalline texture and both shocked and unshocked clasts of the target material. Even though this rock type has been altered, remnant schleiren, metaquartzite, and micritic calcite have been identified. Sample YAX-1_841.32 is representative of this type of rock. It was recovered from a polymict breccia in the middle of the impact sequence.

Gelinas, A.↗