Search NASA⌕ Search

SEARCH · Search NASA

Results for “mobility models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Verification of Ares I Liftoff Acoustic Environments via the Ares I Scale Model Acoustic Test

Launch environments, such as Liftoff Acoustic (LOA) and Ignition Overpressure (IOP), are important design factors for any vehicle and are dependent upon the design of both the vehicle and the ground systems. The NASA Constellation Program had several risks to the development of the Ares I vehicle linked to LOA which are used in the development of the vibro-acoustic environments. The risks included cost, schedule and technical impacts for component qualification due to high predicted vibro-acoustic environments. One solution is to mitigate the environment at the component level. However, where the environment is too severe to mitigate at the component level, reduction of the launch environments is required. The Ares I Scale Model Acoustic Test (ASMAT) program was implemented to verify the predicted Ares I launch environments and to determine the acoustic reduction for the LOA environment with an above deck water sound suppression system. The test article included a 5% scale Ares I vehicle model, tower and Mobile Launcher. Acoustic and pressure data were measured by approximately 200 instruments. The ASMAT results are compared to the Ares I LOA predictions and water suppression effectiveness results are presented.

Counter, Douglas D.↗

Iron-Manganese Redox Reactions in Endeavour Crater Rim Apron Rocks

The Mars Exploration Rover Opportunity has been exploring Noachian age rocks and outcrops on the rim of the 22 km diameter Endeavour crater since August 2011. The Cape York area is a low-lying rim of Endeavour that contains 3 distinct lithologies: 1) the stratigraphically lowest Matijevic fm of pre-impact lithology, 2) Shoemaker fm of impact breccias, and 3) the stratigraphically highest rim lithology Grasberg fm of post-impact sediments that drape the lower slopes of the rim. The sulfate-rich sediment of the Burns fm lies unconformably over the Grasberg fm. Ca-sulfate veins were discovered in Grasberg fm sediments; the sulfates precipitated from aqueous fluids flowing upward through these materials. Opportunity investigated the chemistry and morphology of outcrops in the Matijevic fm that have Fe(sup 3+)-rich smectite detected by orbital signatures returned by CRISM on MRO. Matijevic fm also contains "boxwork" fractures with chemistry consistent with an Al-rich smectite and veins that appear to be rich in Ca-sulfate. More recently on Cape Tribulation, Opportunity has characterized two S-, Mg- and Mn-rich rich rocks overturned and fractured by the rover's wheels on Cook Haven. Those rocks have been dubbed "Pinnacle Island" and "Stuart Island" and will be referred to as the "Island" rocks. The objectives of this study are to characterize the Fe and Mn contents in the Cape York materials, including the two Island rocks, and to provide a model for Mn mobilization and precipitation. Detailed geochemistry of Endeavour rim rocks is presented in a companion paper. Geochemical trends and elemental associations were obtained from data returned by the Alpha Particle X-ray Spectrometer (APXS) on Opportunity.

Ming, D. W.↗

Multibody Simulation of REMORA CubeSat Docking to and Pushing a Spent Rocket Booster

This paper details the multibody simulation of three phases of critical importance to the feasibility of the REMORA CubeSat space debris mitigation concept: the final approach of the CubeSat to a spent rocket booster; the grappling of the spent rocket booster using a robotic arm; and the pushing of the spent rocket booster to divert its course from another on-orbit asset. The extension of a robotic mobility and manipulation modeling toolkit (M3TK) from multibody dynamics simulation of manipulators and ground vehicles to simulation of orbital robotics is outlined. This includes the identification of the appropriate parameters required to concisely and generically describe thruster loads, thruster mixing, spacecraft control, and spacecraft navigation for the purpose of on-orbit robotics simulation. A high-level spacecraft navigator commands maneuvers to target spacecraft states. A PID spacecraft controller takes the target states and calculates desired forces and torques. A thruster mixer solves a quadratic program to determine the optimal thruster firing times for the propulsion system. Pulse width modulated actuation of eight canted cold gas thrusters is used in the simulated approach to a rocket nozzle from a distance of 200 m. A five degree of freedom robotic arm is controlled to position a pair of pincers to grasp the rocket nozzle. Contact dynamics are used to accurately simulate the grasping of the rocket nozzle by the pincers. A similar, but separate simulation is performed to assess the ability of the REMORA CubeSat to push the large spent rocket booster. This diversion maneuver makes use of an additional, larger thruster, and pushes the rocket booster in excess of 400 m. Appropriate motor control gains on the robotic arm are found to be higher during the pushing phase than those which are appropriate during free motion; this increase promotes rigidity of the arm and allows it to properly direct the pushing force. Challenges encountered in time step selection for numerical stability of the simulation are also discussed.

Mukherjee, Rudranarayan↗

Why oil sticks to limestone.

A coordination chemistry analysis of oil-calcite adhesion allows waterflood chemistry controls over enhanced oil recovery from limestones to be understood. The model relies on temperature-dependent surface complexation models of calcite and oil. The primary electrostatic bridges holding oil to calcite are calculated to be [-COO - ][>CaOH 2 + ], [-COO - ][>COOCa + ], [>CaSO 4 - ][-COOCa + ] and [-COOCa + ][>COO - ] (“>” denotes calcite surface groups; “-” denotes polar oil surface groups; Mg 2+ can substitute for Ca +2 ). The [-COO - ][>CaOH 2 + ] bridge between oil carboxylate and protonated calcite calcium sites is most sensitive to changes in waterflood chemistry. Model calculations predict that increased levels of Ca +2 , Mg +2 , and SO 4 -2 , alone or in combination, will increase oil recovery from limestones by decreasing the number of [-COO - ][>CaOH 2 + ] bridges. Divalent cations decrease the local interfacial potential by decreasing the net negative charge on oil carboxylate groups; SO 4 -2 coordinates to protonated calcite calcium sites to decrease charge and electrostatic attraction. Increases in ionic strength should increase adhesion by increasing the net charge on each surface, though the effect will be less on calcite. The model presented here requires no fitting parameters yet accurately reproduces observed oil mobilization trends suggesting the model to be a potentially valuable tool for designing chemistries of waterfloods employed in limestones.

04 OIL SHALES AND TAR SANDS↗

Optimal Sizing of an Electric Vehicle Charging Station with Integration of PV and Energy Storage

This paper proposes an optimization model for the optimal configuration of an grid-connected electric vehicle (EV) extreme fast charging station considering integration of photovoltaic (PV) and energy storage. The proposed model minimizes the annualized net cost (i.e., maximizes the annualized net profit) of the extreme fast charging station, including investment and maintenance cost of charging ports, PV and energy storage, net cost of purchasing energy from utility and selling energy to EV customers, degradation cost of energy storage and demand charge. The decision variables are number of charging ports, capacity of invested PV and the power and energy ratings of invested energy storage. The Erlang-loss system is adopted to model the EV mobility. Results of numerical simulations indicate that investment of PV and energy storage could increase the annualized profit of the extreme fast charging station. In addition, the impacts of various parameters on the optimal solution are investigated by sensitivity analysis.

Liu, Guodong↗

A Design of Activity-Based Mobility Intervention

Human mobility influences our society and vice versa. During the COVID-19 pandemic, non-pharmaceutical intervention that alters activity-based mobility such as work-from-home greatly impacted human mobility patterns. Many studies on developing mitigation strategies have employed or implemented their own mobility intervention within their model assumption. For fair evaluation between intervention strategies across models, it is significant to set up compatible experimental environments. However, it is difficult to apply the identical intervention to different kinds of models and compare their effectiveness because each model might have different assumptions, capabilities, and implementations. Even if one can apply intervention to heterogeneous models, it may produce undesirable artifacts due to difference of models and integration with intervention. Therefore, minimizing undesirable artifacts and facilitating intervention experiments across heterogeneous models are substantial. Taking this into account, this paper investigates a design of activity-based mobility intervention (ABMI). We define ABMI together with related concepts and develop an extensible data model and schema of ABMI based on the 5W1H method that can be used in different models. As a case study, we apply the ABMI model to a micro-simulation to demonstrate the usability of the proposed model. We expect that standardized ABMI and interfaces may help to streamline development and experiments of intervention strategies across heterogeneous models.

Kim, Joon-Seok↗

Experiments with an EVA Assistant Robot

Human missions to the Moon or Mars will likely be accompanied by many useful robots that will assist in all aspects of the mission, from construction to maintenance to surface exploration. Such robots might scout terrain, carry tools, take pictures, curate samples, or provide status information during a traverse. At NASA/JSC, the EVA Robotic Assistant (ERA) project has developed a robot testbed for exploring the issues of astronaut-robot interaction. Together with JSC's Advanced Spacesuit Lab, the ERA team has been developing robot capabilities and testing them with space-suited test subjects at planetary surface analog sites. In this paper, we describe the current state of the ERA testbed and two weeks of remote field tests in Arizona in September 2002. A number of teams with a broad range of interests participated in these experiments to explore different aspects of what must be done to develop a program for robotic assistance to surface EVA. Technologies explored in the field experiments included a fuel cell, new mobility platform and manipulator, novel software and communications infrastructure for multi-agent modeling and planning, a mobile science lab, an "InfoPak" for monitoring the spacesuit, and delayed satellite communication to a remote operations team. In this paper, we will describe this latest round of field tests in detail.

Burridge, Robert R.↗

Correlating the Microstructure of Thin Films of Poly(5,5-Bis(3-Dodecyl-2-Theinyl)-2,2-Bithiophene With Charge Transport: Effect of Dielectric Surface Energy And Thermal Annealing

Poly[5,5{prime}-bis(3-dodecyl-2-thienyl)-2,2{prime}-bithiophene] (PQT-12) is a conjugated polymer that shows promising performance ({micro} > 0.1 cm{sup 2}/V s) as a semiconductor for thin-film electronics. The electrical properties of PQT-12 thin films can vary by over 3 orders of magnitude depending on the chemistry of the substrate onto which they are deposited and on annealing conditions. The highest mobility is obtained in films annealed on a dielectric treated with a self-assembled monolayer of octadecyltrichlorosilane (OTS). Polymeric thin films were processed from either a solution of dissolved PQT-12 molecules in 1,2-dichlorobenzene or from a nanoparticle dispersion of the polymer in the same solvent (nPQT-12). In addition, the substrate surface chemistry was altered by spin coating on a bare SiO{sub 2} dielectric or on SiO{sub 2} treated with OTS. The microstructure of the two forms of polymer, as characterized using specular and grazing x-ray diffraction in addition to rocking curves, was compared and correlated with the electrical performance of the films as active layers in thin-film transistors. As-spun films of nPQT-12 are always more crystalline than those of PQT-12, independent of substrate chemistry. Consequently, carrier mobility in as-spun films is higher in nPQT-12 than in PQT-12. The presence of the OTS monolayer at the polymer/dielectric interface increases crystallinity of both PQT-12 and nPQT-12, without significantly affecting their texture. After annealing, the mobility in PQT-12 films and nPQT-12 films is comparable. Annealing causes the polymer films on OTS to undergo crystallite growth in the direction normal to the substrate. In nPQT-12, growth of the crystalline coherence length in the {pi}-{pi} stacking direction (i.e., parallel to the substrate and in the direction of charge transport) occurs as well. The mobility increase in nPQT-12 on OTS upon annealing is thus attributed to the higher crystallinity of the film. In PQT-12 films deposited on OTS on the other hand, annealing causes a decrease in the out-of-plane misorientation of neighboring crystallites without any significant grain growth in the plane of the film. The mobility increase in PQT-12 on OTS upon annealing is attributed to a better intergrain connectivity, in agreement with electrical modeling of the transistor characteristics using a mobility edge model.

36 MATERIALS SCIENCE↗

Assessing the impact of human mobility to predict regional excess death in Ecuador

Abstract COVID-19 outbreaks have had high mortality in low- and middle-income countries such as Ecuador. Human mobility is an important factor influencing the spread of diseases possibly leading to a high burden of disease at the country level. Drastic control measures, such as complete lockdown, are effective epidemic controls, yet in practice one hopes that a partial shutdown would suffice. It is an open problem to determine how much mobility can be allowed while controlling an outbreak. In this paper, we use statistical models to relate human mobility to the excess death in Ecuador while controlling for demographic factors. The mobility index provided by GRANDATA, based on mobile phone users, represents the change of number of out-of-home events with respect to a benchmark date (March 2nd, 2020). The study confirms the global trend that more men are dying than expected compared to women, and that people under 30 show less deaths than expected, particularly individuals younger than 20 with a death rate reduction between 22 and 27%. The weekly median mobility time series shows a sharp decrease in human mobility immediately after a national lockdown was declared on March 17, 2020 and a progressive increase towards the pre-lockdown level within two months. Relating median mobility to excess deaths shows a lag in its effect: first, a decrease in mobility in the previous two to three weeks decreases excess death and, more novel, we found an increase of mobility variability four weeks prior increases the number of excess deaths.

59 BASIC BIOLOGICAL SCIENCES↗

A Simple Analytical Model for Predicting the Detectable Ion Current in Ion Mobility Spectrometry Using Corona Discharge Ionization Sources

Corona discharge ionization sources are often used in ion mobility spectrometers (IMS) when a non-radioactive ion source with high ion currents is required. Typically, the corona discharge is followed by a reaction region where analyte ions are formed from the reactant ions. In this work, we present a simple yet sufficiently accurate model for predicting the ion current available at the end of this reaction region when operating at reduced pressure as in High Kinetic Energy Ion Mobility Spectrometers (HiKE-IMS) or most IMS-MS instruments. It yields excellent qualitative agreement with measurement results and is even able to calculate the ion current within an error of 15%. Additional interesting findings of this model are the ion current at the end of the reaction region being independent from the ion current generated by the corona discharge and the ion current in High Kinetic Energy Ion Mobility Spectrometers (HiKE-IMS) growing quadratically when scaling down the length of the reaction region. .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Expected Improvements in Work Truck Efficiency Through Connectivity and Automation

This presentation focuses on the potential impact of connected and automated technologies on commercial vehicle operations. It includes topics such as the U.S. Department of Energy's Energy Efficient Mobility Systems (EEMS) program and the Systems and Modeling for Accelerated Research in Transportation (SMART) Mobility Initiative. It also describes National Renewable Energy Laboratory (NREL) research findings pertaining to the potential energy impacts of connectivity and automation and stresses the need for integration and optimization to take advantage of the benefits offered by these transformative technologies while mitigating the potential negative consequences.

33 ADVANCED PROPULSION SYSTEMS↗

The Highly Integrated Vehicle Ecosystem (HIVE): A Platform for Managing the Operations of On-Demand Vehicle Fleets

This paper introduces the Highly Integrated Vehicle Ecosystem (HIVE), a transportation modeling tool developed by within the Center for Integrated Mobility Sciences (CIMS) group at the National Renewable Energy Laboratory (NREL). HIVE is an agent-based supply/demand model for Mobility on Demand (MoD) which mixes agent-based modeling and centralized dispatch for automated and human-driven fleets and ride hail passengers. Research questions using HIVE span multiple categories, including intelligent fleet planning (assessing fleet, battery, and infrastructure investment decisions), intelligent fleet control (charge management, vehicle dispatching) and strategic business model decision-making (depot-based full-time drivers versus gig-based drivers, human-driven versus automated). The components of the HIVE model are explained and then HIVE is demonstrated in a case study using demand data from the New York City Taxi & Limousine Commission data set.

33 ADVANCED PROPULSION SYSTEMS↗

Open-Source Data for MAC-POSTS: Mobility Data Analytics Center - Prediction, Optimization, and Simulation Toolkit for Transportation Systems

MAC-POSTS (Mobility Data Analytics Center - Prediction, Optimization, and Simulation toolkit for Transportation Systems) is a toolkit for dynamic transportation network modeling. Developed by the Mobility Data Analytics Center (MAC) at Carnegie Mellon University, this package implements many classic dynamic transportation network models, as well as new models proposed by MAC members. It has served as one building block for many other models and research projects. As such, this package used to be treated as an internal research project of the MAC lab, and admittedly, the code base is messy, and the interface is hard to use. However, we are working hard to make it a generally usable and useful toolkit for dynamic transportation network modeling. We would really appreciate any feedback, comments, suggestions, or criticisms.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Localization in one-dimensional lattices with non-nearest-neighbor hopping: Generalized Anderson and Aubry-Andre models

We study the quantum localization phenomena of noninteracting particles in one-dimensional lattices based on tight-binding models with various forms of hopping terms beyond the nearest neighbor, which are generalizations of the famous Aubry-Andre and noninteracting Anderson models. For the case with deterministic disordered potential induced by a secondary incommensurate lattice (i.e., the Aubry-Andre model), we identify a class of self-dual models, for which the boundary between localized and extended eigenstates are determined analytically by employing a generalized Aubry-Andre transformation. We also numerically investigate the localization properties of nondual models with next-nearest-neighbor hopping, Gaussian, and power-law decay hopping terms. We find that even for these nondual models, the numerically obtained mobility edges can be well approximated by the analytically obtained condition for localization transition in the self-dual models, as long as the decay of the hopping rate with respect to distance is sufficiently fast. For the disordered potential with genuinely random character, we examine scenarios with next-nearest-neighbor hopping, exponential, Gaussian, and power-law decay hopping terms numerically. We find that the higher-order hopping terms can remove the symmetry in the localization length about the energy band center compared to the Anderson model. Furthermore, our results demonstrate that for the power-law decay case, there exists a critical exponent below which mobility edges can be found. Our theoretical results could, in principle, be directly tested in shallow atomic optical lattice systems enabling non-nearest-neighbor hopping.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

On the Effect of Sphere-Overlap on Super Coarse-Grained Models of Protein Assemblies

Ion mobility mass spectrometry (IM/MS) can provide structural information on intact protein complexes. Such data, including connectivity and collision cross sections (CCS) of assemblies’ subunits, can in turn be used as a guide to produce representative super coarse-grained models. These models are constituted by ensembles of overlapping spheres, each representing a protein subunit. A model is considered plausible if the CCS and sphere-overlap levels of its subunits fall within predetermined confidence intervals. While the first is determined by experimental error, the latter is based on a statistical analysis on a range of protein dimers. Here, we first propose a new expression to describe the overlap between two spheres. Then we analyze the effect of specific overlap cutoff choices on the precision and accuracy of super coarse-grained models. Finally, we propose a method to determine overlap cutoff levels on a per-case scenario, based on collected CCS data, and show that it can be applied to the characterization of the assembly topology of symmetrical homo-multimers. .

74 ATOMIC AND MOLECULAR PHYSICS↗

Southeast Carbon Sequestration Partnership (SECARB) Phase III Anthropogenic Test at Citronelle Field, Mobile Co., AL. Post-Injection Period Reservoir Modeling Report

The Southeast Carbon Sequestration Partnership (SECARB) Anthropogenic Test is a U.S. Department of Energy funded fully integrated carbon capture and storage initiative designed to demonstrate deep underground injection and containment of anthropogenic CO 2 sourced from Alabama Power’s Plant Barry. From August 20, 2012 to September 1, 2014, a total of 114,014 metric tonnes of CO 2 were transported via pipeline from Plant Barry and stored in a saline aquifer under a portion of the Citronelle Field operated by Denbury Onshore, LLC near Citronelle, Alabama. A major component of this project was to test and develop techniques to monitor, verify and account (MVA) for the CO 2 stored in the aquifer by the project. A suite of technologies were applied and developed to demonstrate non-endangerment of underground sources of drinking water (USDW’s) and to ensure that CO2 does not migrate out of intended zones within the subsurface. This involved several levels of monitoring: 1) Surface monitoring, 2) shallow groundwater monitoring, 3) deep reservoir monitoring and experimental MVA activities. Numerical models were developed to determine the project’s Area of Review (AoR) and to investigate the simulated advancement of the CO 2 plume through the subsurface aquifer for 30 years after the end of injection. An initial baseline area of review of 1,700 ft. was established. The key results demonstrating non-endangerment of USDW’s are presented.

01 COAL, LIGNITE, AND PEAT↗