Search NASA⌕ Search

SEARCH · Search NASA

Results for “pressure sensor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Hybrid Flush and Synthetic Air Data Filter for Entry Vehicle Atmospheric State Estimation

A hybrid flush/synthetic air data sensing filter utilizing Kalman-Schmidt and Rach-Tung-Striebel smoothers is developed to obtain entry vehicle atmosphere estimates. The filter/smoother blends information from pressure sensors distributed on the heatshield with measurements of the vehicle aerodynamic forces and moments computed from mass properties and inertial measurement unit data, and prior estimates of the atmosphere. The filter produces estimates of the atmospheric conditions along the entry trajectory, and systematic error estimates to reconcile differences between the pressure and aerodynamic data sources. The filter is applied to data acquired during the Mars Science Laboratory and Mars 2020 entry, descent, and landing at Gale crater and at Jezero crater, respectively. The results show that the hybrid filter produces estimates of the freestream flight condition with lower uncertainty than either the flush or synthetic air data algorithms. The filter accomplishes this result by incorporating additional data and computing estimates of systematic error parameters in the pressure data and the aerodynamic model to further reduce the uncertainties.

Christopher D. Karlgaard↗
NASA NTRS1994

Measurement uncertainty and feasibility study of a flush airdata system for a hypersonic flight experiment

Presented is a feasibility and error analysis for a hypersonic flush airdata system on a hypersonic flight experiment (HYFLITE). HYFLITE heating loads make intrusive airdata measurement impractical. Although this analysis is specifically for the HYFLITE vehicle and trajectory, the problems analyzed are generally applicable to hypersonic vehicles. A layout of the flush-port matrix is shown. Surface pressures are related airdata parameters using a simple aerodynamic model. The model is linearized using small perturbations and inverted using nonlinear least-squares. Effects of various error sources on the overall uncertainty are evaluated using an error simulation. Error sources modeled include boundarylayer/viscous interactions, pneumatic lag, thermal transpiration in the sensor pressure tubing, misalignment in the matrix layout, thermal warping of the vehicle nose, sampling resolution, and transducer error. Using simulated pressure data for input to the estimation algorithm, effects caused by various error sources are analyzed by comparing estimator outputs with the original trajectory. To obtain ensemble averages the simulation is run repeatedly and output statistics are compiled. Output errors resulting from the various error sources are presented as a function of Mach number. Final uncertainties with all modeled error sources included are presented as a function of Mach number.

Whitmore, Stephen A.↗
DOE OSTI2020

Optical Fiber Sensor Technology Development and Field Validation for Distribution Transformer and Other Grid Asset Health Monitoring

Power transformers are critical pieces of infrastructure in the electric grid that are both extremely expensive and difficult to replace. These transformers often have long lead times for replacement, and failures can create long service disruptions. This project has developed a new suite of sensors designed to give early warning of the impending failure of these important power transformers before it is too late and a major failure occurs. By using novel fiber optic sensors instead of conventional existing technologies, we are able to measure transformer characteristics indicative of impending failures in ways that were not previously possible. These new optical fiber-based sensors are completely immune to the strong magnetic fields present in power transformers, as well as being capable of using distributed measurement techniques. Distributed measurement techniques enable the fiber to return information all along its length as opposed to only collecting data at a single point; as would a thermocouple or standard pressure sensor.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRSDate not supplied

Hybrid Flush and Synthetic Air Data Filter for Entry Vehicle Atmospheric State Estimation

A hybrid flush/synthetic air data sensing filter for entry vehicle atmosphere estimation is developed. The approach makes use of a Kalman-Schmidt and Rauch-Tung-Streibel smoother. The filter/smoother blends information from pressure sensors distributed on the heatshield with pseudo-measurements of the vehicle aerodynamic forces and moments computed from mass properties and inertial measurement unit data, and prior estimates of the atmosphere. The filter produces estimates of the atmospheric conditions along the entry trajectory, and systematic error estimates to reconcile differences between the pressure and aerodynamic data sources. The filter is applied to data acquired during the Mars 2020 entry, descent, and landing at Jezero crater on February 18th, 2021. The final paper will also include results from the Mars Science Laboratory entry, descent, and landing.

Chris D. Karlgaard↗
NASA NTRS1992

A satellite anemometer

We present the conceptual design of an instrument that can provide a continuous analog measure of the pitch and yaw angles of a low altitude satellite in the frame of the neutral atmosphere. The device, which uses pressure sensor orientation to provide its signal, can function in an attitude control loop and/or be used to measure atmospheric winds or wave motions. Any arbitrary angle of attack (pitch and yaw) less than +/- 45 deg can be selected for a heading. The sensitivity of the device is 0.1 deg but this would be limited by low ambient pressure at high altitudes and by multiple particle collisions in and below the slip flow region. The development of a prototype flight unit is in progress.

Hanson, W. B.↗
NASA NTRSDate not supplied

Development and Testing of Pulse Guns for Combustion Instability Testing

Combustion stability requirements of a liquid propellant rocket engine are most commonly verified by evaluating the oscillatory pressure or vibration characteristics following an artificial disturbance of the combustion in the combustion chamber. Two types of devices are most commonly used for dynamic stability rating – nondirectional bombs and pulse guns. Bombs have historically been used most often, especially for the large engines developed around the Apollo era. However, bombs in recent years have become much more expensive and difficult to procure, and their transportation and handling requirements have become more demanding. Pulse guns, with inherently less expensive materials, and far less restrictive handling and shipping requirements, have become an attractive alternative. The NASA Marshall Space Flight Center has developed a pulse gun for use during future development programs at the center, and as a design reference for interested commercial users. The objective of this paper is to present the different variants of the pulse gun and characterize performance over a range of parameters. The parameters include the breech diameter and corresponding volume, barrel length, amount of gun powder used, the method of containing the gunpowder within the breech, and the pressure rating of the burst disk. In total, 44 tests were conducted with the pulse gun firing into a test chamber pressurized to 2300 psig with gaseous nitrogen. The best experimental results – including the highest and most consistent peak pressure amplitudes recorded by dynamic pressure sensors in the test chamber – were from a configuration consisting of a 0.40” inner-diameter breech, 15-16 grains of gunpowder wrapped in cigarette paper, and a 24,000 psid burst disk. With this configuration, the zero-to-peak overpressures recorded in the test chamber ranged from about 37% to 58% of the 2300 psig mean pressure, which is adequate for typical combustion stability rating. To complement the data analysis, the acoustics of the pressure waves as they propagated through the pulse gun and into the test chamber were modeled. A more comprehensive final report of this pulse gun development program is planned to be available in the near future.

Pulse Gun↗
DOE OSTI2020

Measurements of Density and Sound Speed in Mixtures Relevant to Supercritical CO2 Cycles

Abstract The objective of this research is to validate properties of mixtures relevant to supercritical carbon dioxide (sCO2) power cycles. Direct-fired sCO2 cycles are a promising technology for the future power generation systems. The working fluid of sCO2 cycles will be near and above critical point of CO2. One of the challenges is that the simulation of mixtures should consider real gas behavior. Expected operating conditions of Allam cycles reach up to 300 bar and 1000 °C. Characterizing the mixtures at the extreme conditions is an important issue in current researches and industrial applications. Thermophysical properties of mixtures may be beyond the valid range of the widely used database such as NIST REFPROP. Experimental data of mixture properties in the literature are limited which is necessary to develop high-fidelity design tools for sCO2 power cycles. We measured the density and sound speed of several multi-component mixtures. A temperature-controlled high-pressure test cell was used for the density measurements. Sound speed was measured by resonant frequency detection using an external speaker and a piezoelectric pressure sensor. Mixtures studied in this work include carbon dioxide, methane, oxygen, and water vapor. Properties of pure CO2 were measured to show the validity of our technique. Compositions were selected to be close to frozen mixtures at the inlet, mid-progress, and exhaust conditions of a model sCO2 combustor in the previous numerical simulation work. Corresponding reaction progress variables (RPV) were RPV = 0, 0.5, and 1. Temperature and pressure conditions of experiments are 310–450 K and 0–150 bar. In our study, density and sound speed from the NIST REFPROP database agree with experimental measurements within the range of our measurement uncertainties.

Energy & Fuels↗
NASA NTRS2001

A Novel Telometric Metric for In-Situ Measurement of Intrauterine Pressure (IUP) in Pregnant and Parturient Rats

During labor and birth, considerable forces exerted on fetuses help instigate certain adaptive postpartum responses (viz., breathing and suckling). To make precise, reliable measures of the forces experienced by rat fetuses during parturition, we developed a novel method for measuring intrauterine pressure (IUP) in late pregnant rats. A small (1.25 x 4cm) telemetric blood pressure sensor is fitted within a fluid-filled balloon, similar in size to a full term rat fetus. The balloon is surgically implanted in the uterus on Gestational Day 19 of the rats' 22-day pregnancy. During birth, dams are able to deliver their pups and the balloon. IUP arsenals are recorded during labor (G22 or 23) and birth. Data derived from a group of implanted rats indicated that pressures on the balloon increased across the period of birth, reaching 18 mmHg during labor, 25 mmHg during pup births and 39 mmHg just prior to delivery of the balloon. These data are within the range reported for conventional IUP measurement techniques. Dams are simultaneously videotaped, enabling us to analyze behavioral expressions of labor contractions and to integrate in-situ and behavioral findings.

Baer, Lisa A.↗
NASA NTRS2004

Real-Time Unsteady Loads Measurements Using Hot-Film Sensors

Several flight-critical aerodynamic problems such as buffet, flutter, stall, and wing rock are strongly affected or caused by abrupt changes in unsteady aerodynamic loads and moments. Advanced sensing and flow diagnostic techniques have made possible simultaneous identification and tracking, in realtime, of the critical surface, viscosity-related aerodynamic phenomena under both steady and unsteady flight conditions. The wind tunnel study reported here correlates surface hot-film measurements of leading edge stagnation point and separation point, with unsteady aerodynamic loads on a NACA 0015 airfoil. Lift predicted from the correlation model matches lift obtained from pressure sensors for an airfoil undergoing harmonic pitchup and pitchdown motions. An analytical model was developed that demonstrates expected stall trends for pitchup and pitchdown motions. This report demonstrates an ability to obtain unsteady aerodynamic loads in real time, which could lead to advances in air vehicle safety, performance, ride-quality, control, and health management.

Mangalam, Arun S.↗
NASA NTRS2004

Real-Time Unsteady Loads Measurements Using Hot-Film Sensors

Several flight-critical aerodynamic problems such as buffet, flutter, stall, and wing rock are strongly affected or caused by abrupt changes in unsteady aerodynamic loads and moments. Advanced sensing and flow diagnostic techniques have made possible simultaneous identification and tracking, in real-time, of the critical surface, viscosity-related aerodynamic phenomena under both steady and unsteady flight conditions. The wind tunnel study reported here correlates surface hot-film measurements of leading edge stagnation point and separation point, with unsteady aerodynamic loads on a NACA 0015 airfoil. Lift predicted from the correlation model matches lift obtained from pressure sensors for an airfoil undergoing harmonic pitchup and pitchdown motions. An analytical model was developed that demonstrates expected stall trends for pitchup and pitchdown motions. This report demonstrates an ability to obtain unsteady aerodynamic loads in real-time, which could lead to advances in air vehicle safety, performance, ride-quality, control, and health management.

Mangalam, Arun S.↗
DOE OSTI2022

Influence of Vane Trailing Edge Flow on the Formation of Cavity Cells and Rim Sealing

Abstract Hot gas ingestion into the turbine rim seal cavity is an important concern for engine designers. To prevent ingestion, rim seals use high-pressure purge flow; however, the penalty is that excessive use of the purge flow decreases engine thermal efficiency. In this paper, a one-stage turbine operating at engine-representative conditions was used to study the effect of steady and time-resolved under-platform cavity temperatures and pressures across a range of coolant flowrates in the presence of vane trailing edge (VTE) flow. This study correlates time-resolved pressure with time-resolved temperature to identify primary frequencies driving ingestion. At certain flowrates, the time-resolved pressures are out of phase with the temperatures, indicating ingestion. Measurements from high-frequency response pressure sensors in the rim seal and vane platform were also used to determine rotational speed and quantity of large-scale structures (cells). In a parallel effort, a computational model using Unsteady Reynolds-averaged Navier–Stokes (URANS) was applied to determine swirl ratio in the rim seal cavity and time-resolved rim sealing effectiveness. The experimental results confirm that at low purge flowrates, the VTE flow influences the unsteady flow field by decreasing pressure unsteadiness in the rim seal cavity. Results show an increase in purge flow increases the number of unsteady large-scale structures in the rim seal and decreases their rotational speed. However, VTE flow was shown to not significantly change the cell speed and count in the rim seal. Simulations point to the importance of the large-scale cell structures in influencing rim sealing unsteadiness, which is not captured in current rim sealing predictive models.

Engineering↗
NASA NTRS2023

Development of a Field-Deployable Microphone Phased Array for Airframe Noise Flyover Measurements

This technical memorandum describes in detail the construction and use of a large channel-count, field-deployable microphone phased array designed for airframe noise flyover measurements for a range of aircraft types and scales. The array incorporated 185 hardened, weather-resistant sensors suitable for outdoor use. A custom 4-mA current loop receiver circuit with temperature compensation was developed to power the sensors over extended cable lengths with minimal loss of signal-to-noise. Extensive calibrations and performance testing of the sensors were conducted to verify the design specifications. A compact data system combining sensor power, signal conditioning, and digitization was assembled for use with the array. Complementing the data system was a robust analysis system capable of near real-time presentation of beamformed and deconvolved contour plots and integrated spectra obtained from data acquired during flyover passes of the array. Additional instrumentation systems needed to process the array data were also developed, including a commercial 10-meter weather station comprised of a sonic anemometer, aspirated temperature/humidity probe and pressure sensor. Unique methods for assessing the health of the array in-situ were developed and demonstrated. A detailed mock-up of the instrumentation suite (phased array, weather station, and data processor) was performed in the NASA Langley Acoustic Development Laboratory in 2014 to vet the system performance. Issues with the sensors and electronics were identified during the mock-up and subsequently corrected. The array was then deployed for preliminary field testing at Fort A.P. Hill in Virginia in 2015 followed by the array being utilized in three separate full-scale airframe noise test campaigns at Edwards Air Force Base in California from 2016 to 2018 where the system was used to characterize the noise generated by both baseline and treated flaps and main landing gear on a commercial transport-sized vehicle.

Phased Array↗
NASA NTRS2012

Experimental Investigation of Cavitation Induced Feedline Instability from an Orifice

This paper details the results of an experimental investigation into the cavitation instabilities created by a circular orifice conducted at the University of Alabama in Huntsville Propulsion Research Center. This experiment was conducted in concert with a computational simulation to serve as a reference point for the simulation. Testing was conducted using liquid nitrogen as a cryogenic propellant simulant. A 1.06 cm diameter thin orifice with a rounded inlet was tested in an approximately 1.25 kg/s flow with inlet pressures ranging from 504.1 kPa to 829.3 kPa. Pressure fluctuations generated by the orifice were measured using a high frequency pressure sensor located 0.64 tube diameters downstream of the orifice. Fast Fourier Transforms were performed on the high frequency data to determine the instability frequency. Shedding resulted in a primary frequency with a cavitation related subharmonic frequency. For this experiment, the cavitation instability ranged from 153 Hz to 275 Hz. Additionally, the strength of the cavitation occur red as a function of cavitation number. At lower cavitation numbers, the strength of the cavitation instability ranged from 2.4 % to 7 % of the inlet pressure. However, at higher cavitation numbers, the strength of the cavitation instability ranged from 0.6 % to 1 % of the inlet pressure.

Hitt, Matthew A.↗
NASA NTRS2001

On the Fabrication and Behavior of Diamond Microelectromechanical Sensors (DMEMS)

CVD (chemically vapor deposited) diamond films can be processed similar to "conventional" semiconductor device fabrication and as such can be used to achieve microelectromechanical structures (MEMS) also similar to, for example, silicon technology. Very small cantilever beams, membranes, stripes, tips, etc. can be constructed in doped and undoped diamond films and offer an array of choices in diamond with its known superior properties such as elastic modulus, high temperature semiconduction, high thermal conductivity, very low coefficient of expansion and numerous other diamond parameters. This paper will review the construction and behavior of the second generation DMEMS devices comprised as an accelerometer with a diamond diaphragm for use in very high G applications and a diamond pressure sensor for very high temperature and frequency response.

Holmes, K.↗
NASA NTRS1995

Calibration Of Partial-Pressure-Of-Oxygen Sensors

Report and analysis of, and discussion of improvements in, procedure for calibrating partial-pressure-of-oxygen sensors to satisfy Spacelab calibration requirements released. Sensors exhibit fast drift, which results in short calibration period not suitable for Spacelab. By assessing complete process of determining total drift range available, calibration procedure modified to eliminate errors and still satisfy requirements without compromising integrity of system.

Yount, David W.↗
NASA NTRS2011

Comparison of Ares I-X Wind-Tunnel Derived Buffet Environment with Flight Data

The Ares I-X Flight Test Vehicle (FTV), launched in October 2009, carried with it over 243 buffet verification pressure sensors and was one of the most heavily instrumented launch vehicle flight tests. This flight test represented a unique opportunity for NASA and its partners to compare the wind-tunnel derived buffet environment with that measured during the flight of Ares I-X. It is necessary to define the launch vehicle buffet loads to ensure that structural components and vehicle subsystems possess adequate strength, stress, and fatigue margins when the vehicle structural dynamic response to buffet forcing functions are considered. Ares I-X buffet forcing functions were obtained via wind-tunnel testing of a rigid buffet model (RBM) instrumented with hundreds of unsteady pressure transducers designed to measure the buffet environment across the desired frequency range. This paper discusses the comparison of RBM and FTV buffet environments, including fluctuating pressure coefficient and normalized sectional buffet forcing function root-mean-square magnitudes, frequency content of power-spectral density functions, and force magnitudes of an alternating flow phenomena. Comparison of wind-tunnel model and flight test vehicle buffet environments show very good agreement with root-mean-square magnitudes of buffet forcing functions at the majority of vehicle stations. Spectra proved a challenge to compare because of different wind-tunnel and flight test conditions and data acquisition rates. However, meaningful and promising comparisons of buffet spectra are presented. Lastly, the buffet loads resulting from the transition of subsonic separated flow to supersonic attached flow were significantly over-predicted by wind-tunnel results.

Piatak, David J.↗
NASA NTRS2019

Laboratory Scale Testing of Ignition Overpressure for Space Vehicle Launch Pad Environments

A scale model of a NASA representative space vehicle is used to develop a refined estimate of the transient pressure loads that are expected to form at the base of the vehicle in the event of a vapor cloud explosion. Flammable vapor clouds are known to form prior to engine startup due to the significant amount of unburned hydrogen that is ejected from the combustion chamber. In the event of a vapor cloud explosion, the vehicle and payload must be able to withstand the resulting overpressure waves. The study comprises an array of pressure sensors located along the base heat shield of the scale model space vehicle as well as the interior wall and throat plug plane of the solid rocket booster. A spark source generator is used to simulate the overpressure wave produced by a vapor cloud explosion while measurements are acquired with and without the effect of a mobile launcher. Time- resolved schlieren images of the simulated vapor cloud explosion reveal the path and impact of both the initial wave and several reflected waves on the various components at the base of the space vehicle. In some instances, the reflected waves superpose to create waves that are higher in amplitude than the initial overpressure wave. A time frequency analysis of the pressure waveforms measured inside the solid rocket booster reveal a ring down tone corresponding to a standing wave that is four times the length of the nozzle.

Tinney, Charles E.↗
NASA NTRS1999

Fiber Optic Microphone

Research into advanced pressure sensors using fiber-optic technology is aimed at developing compact size microphones. Fiber optic sensors are inherently immune to electromagnetic noise, and are very sensitive, light weight, and highly flexible. In FY 98, NASA researchers successfully designed and assembled a prototype fiber-optic microphone. The sensing technique employed was fiber optic Fabry-Perot interferometry. The sensing head is composed of an optical fiber terminated in a miniature ferrule with a thin, silicon-microfabricated diaphragm mounted on it. The optical fiber is a single mode fiber with a core diameter of 8 micron, with the cleaved end positioned 50 micron from the diaphragm surface. The diaphragm is made up of a 0.2 micron thick silicon nitride membrane whose inner surface is metallized with layers of 30 nm titanium, 30 nm platinum, and 0.2 micron gold for efficient reflection. The active sensing area is approximately 1.5 mm in diameter. The measured differential pressure tolerance of this diaphragm is more than 1 bar, yielding a dynamic range of more than 100 dB.

Cho, Y. C.↗