Search NASA⌕ Search

SEARCH · Search NASA

Results for “rotating flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Effect of shaft rotation on the incompressible flow in a labyrinth seal

The incompressible flow in a labyrinth seal at low leakage rates was computationally and experimentally investigated over a wide range of seal rotation rates. QUICK differencing was employed in the finite difference code to reduce the effects of false diffusion. The use of measured inlet boundary conditions for the axial and swirl velocity components and for the turbulent kinetic energy resulted in good agreement between velocity predictions and hot-film measurements. It was found that when the rotation rate is increased beyond a certain point, a second recirculation zone forms inside the seal cavity, altering the flow field in the cavity and resulting in a substantial increase in the pressure drop across it.

Demko, J. A.↗
NASA NTRS1991

Active unsteady aerodynamic suppression of rotating stall in an incompressible flow centrifugal compressor with vaned diffuser

A mathematical model is developed to analyze the suppression of rotating stall in an incompressible flow centrifugal compressor with a vaned diffuser, thereby addressing the important need for centrifugal compressor rotating stall and surge control. In this model, the precursor to to instability is a weak rotating potential velocity perturbation in the inlet flow field that eventually develops into a finite disturbance. To suppress the growth of this potential disturbance, a rotating control vortical velocity disturbance is introduced into the impeller inlet flow. The effectiveness of this control is analyzed by matching the perturbation pressure in the compressor inlet and exit flow fields with a model for the unsteady behavior of the compressor. To demonstrate instability control, this model is then used to predict the control effectiveness for centrifugal compressor geometries based on a low speed research centrifugal compressor. These results indicate that reductions of 10 to 15 percent in the mean inlet flow coefficient at instability are possible with control waveforms of half the magnitude of the total disturbance at the inlet.

Lawless, Patrick B.↗
NASA NTRS1986

Structure parameters in rotating Couette-Poiseuille channel flow

It is well-known that a number of steady state problems in fluid mechanics involving systems of nonlinear partial differential equations can be reduced to the problem of solving a single operator equation of the form: v + lambda Av + lambda B(v) = 0, v is the summation of H, lambda is the summation of one-dimensional Euclid space, where H is an appropriate (real or complex) Hilbert space. Here lambda is a typical load parameter, e.g., the Reynolds number, A is a linear operator, and B is a quadratic operator generated by a bilinear form. In this setting many bifurcation and stability results for problems were obtained. A rotating Couette-Poiseuille channel flow was studied, and it showed that, in general, the superposition of a Poiseuille flow on a rotating Couette channel flow is destabilizing.

Knightly, George H.↗
NASA NTRS1972

Magnetic energy flow in the solar wind.

Discussion of the effect of rotation (tangential flow) of the solar wind on the conclusions of Whang (1971) suggesting an increase in the solar wind velocity due to the conversion of magnetic energy to kinetic energy. It is shown that the effect of the rotation of the sun on the magnetic energy flow results in most of the magnetic energy being transported by magnetic shear stress near the sun.

Modisette, J. L.↗
DOE OSTI2024

Broadband Rotational Spectroscopy in Uniform Supersonic Flows: Chirped Pulse/Uniform Flow for Reaction Dynamics and Low Temperature Kinetics

ConspectusThe study of gas-phase chemical reactions at very low temperatures first became possible with the development and implementation of the CRESU (French acronym for Reaction Kinetics in Uniform Supersonic Flows) technique. CRESU relies on a uniform supersonic flow produced by expansion of a gas through a Laval (convergent-divergent) nozzle to produce a wall-less reactor at temperatures from 10 to 200 K and densities of 1016-1018 cm-3 for the study of low temperature kinetics, with particular application to astrochemistry. In recent years, we have combined uniform flows with revolutionary advances in broadband rotational spectroscopy to yield an instrument that affords near-universal detection for novel applications in photodissociation, reaction dynamics, and kinetics. This combination of uniform supersonic flows with chirped-pulse Fourier-transform microwave spectroscopy (Chirped-Pulse/Uniform Flow, CPUF) permits detection of any species with a modest dipole moment, thermalized to the uniform temperature of the gas flow, with isomer, conformer, and vibrational state specificity. In addition, the use of broadband, high-resolution, and time-dependent (microsecond time scale) micro- and mm-wave spectroscopy makes it an ideal tool for characterizing both transient and stable molecules, as well as studying their spectroscopy and dynamics.In this Account, we review recent advances made using the CPUF technique, including studies of photodissociation, radical-radical reaction dynamics, and low temperature kinetics. These studies highlight both the strength of universal and multiplexed detection and the challenges of coupling it to a high-density collisional environment. Product branching and product evolution as a function of time have been measured for astrochemically relevant systems, relying on the detailed characterization of these flow conditions via experiments and fluid dynamics simulations. In the photodissociation of isoxazole, an unusual heterocyclic molecule with a very low-energy conical intersection, we have identified 7 products in 5 reaction channels and determined the product branching, pointing to both direct and indirect pathways. We have also approached the same system from separated NO and C3H3 reactants to explore a broader range of the potential energy surface, demonstrating the power of multichannel branching measurements for complex radical-radical reactions. We determined the product branching in the C3H2 isomers in the photodissociation of the propargyl radical and identified the importance of a hydrogen atom catalyzed isomerization to the lowest energy cyclic form. This then motivated a study of direct D-H exchange reaction in radicals, in which we demonstrate that it is an important and overlooked pathway for deuterium fractionation in astrochemical environments. Recently, we have shown the measurement of low temperature kinetics inside an extended Laval nozzle, after which a shock-free secondary expansion to low temperature and density affords an ideal environment for detection by rotational spectroscopy. These results highlight the power and potential of the CPUF approach, and future prospects will also be discussed in light of these developments.

Dias, Nureshan↗
NASA NTRS1985

Turbulence modelling for complex shear flows

The turbulence models available for the prediction of complex turbulent shear layers are reviewed in this paper, concentrating mainly on three-dimensional flows, flows subjected to curvature and body rotation, separated flows, and vortex flows. A critical review of zero-equation, one-equation, two-equation, algebraic Reynolds stress, and full Reynolds stress models are carried out, with a specific emphasis on their applicability to complex flows. It is concluded that algebraic eddy viscosity models and kappa-epsilon/kappa-omega models, with a constant value of coefficients, are not adequate for complex flows. The models which include a description of stresses, either through an algebraic Reynolds stress model or a full Reynolds stress model, are essential for adequate prediction of these flows. It is recommended that systematic experimental investigations be carried out to isolate various complex interactions in order to understand and model the various effects and to carry out an extension of the present models to include complex flows.

Lakshminarayana, B.↗
NASA NTRS1988

A semianalytical technique for sensitivity analysis of unsteady aerodynamic computations

A semianalytical approach is developed for the sensitivity analysis of linear unsteady aerodynamic loads. The semianalytical approach is easier to implement than the analytical approach. It is also computationally less expensive than the finite difference approach when used with panel methods, which require a large number of panels. The semianalytical approach is applied to an isolated airfoil in a 2-D flow and rotating propfan blades in 3-D flow. Sensitivity coefficients with respect to non-shape-dependent variables are shown for some cases. It is expected that the semianalytical approach will be useful in aeroelastic design procedures particularly when mistuning is present, and that it is potentially useful for shape sensitivity analysis of linear unsteady aerodynamics.

Murthy, Durbha V.↗
NASA NTRS1989

3D computational analyses for SSME internal flows

Two qualities of the turbulent flow of hot gases in liquid fueled rocket engines that affect the selection and performance of turbulence models used in computational fluid analyses of the flow are curvature of the flow passages and rotation of the flow. Three configurations which represent these conditions and for which experimental data are available are subjected to three dimensional computational analyses using both the standard k - epsilon and a multiple-time-scale turbulence models. It is found that the multiple-time-scale model is better able to predict overall flow features, especially where regions of separated flow are present.

Chen, C. P.↗
NASA NTRS1990

Counterrotating prop-fan simulations which feature a relative-motion multiblock grid decomposition enabling arbitrary time-steps

Improvements are presented of a computer algorithm developed for the time-accurate flow analysis of rotating machines. The flow model is a finite volume method utilizing a high-resolution approximate Riemann solver for interface flux definitions. The numerical scheme is a block LU implicit iterative-refinement method which possesses apparent unconditional stability. Multiblock composite gridding is used to orderly partition the field into a specified arrangement of blocks exhibiting varying degrees of similarity. Block-block relative motion is achieved using local grid distortion to reduce grid skewness and accommodate arbitrary time step selection. A general high-order numerical scheme is applied to satisfy the geometric conservation law. An even-blade-count counterrotating unducted fan configuration is chosen for a computational study comparing solutions resulting from altering parameters such as time step size and iteration count. The solutions are compared with measured data.

Janus, J. Mark↗
NASA NTRS1993

The embedded young stars in the Taurus-Auriga molecular cloud. I - Models for spectral energy distributions

We describe radiative transfer calculations of infalling, dusty envelopes surrounding pre-main-sequence stars and use these models to derive physical properties for a sample of 21 heavily reddened young stars in the Taurus-Auriga molecular cloud. The density distributions needed to match the FIR peaks in the spectral energy distributions of these embedded sources suggest mass infall rates similar to those predicted for simple thermally supported clouds with temperatures about 10 K. Unless the dust opacities are badly in error, our models require substantial departures from spherical symmetry in the envelopes of all sources. These flattened envelopes may be produced by a combination of rotation and cavities excavated by bipolar flows. The rotating infall models of Terebey et al. (1984) models indicate a centrifugal radius of about 70 AU for many objects if rotation is the only important physical effect, and this radius is reasonably consistent with typical estimates for the sizes of circumstellar disks around T Tauri stars.

Kenyon, Scott J.↗
NASA NTRS1995

On the consistency of Reynolds stress turbulence closures with hydrodynamic stability theory

The consistency of second-order closure models with results from hydrodynamic stability theory is analyzed for the simplified case of homogeneous turbulence. In a recent study, Speziale, Gatski, and MacGiolla Mhuiris showed that second-order closures are capable of yielding results that are consistent with hydrodynamic stability theory for the case of homogeneous shear flow in a rotating frame. It is demonstrated in this paper that this success is due to the fact that the stability boundaries for rotating homogeneous shear flow are not dependent on the details of the spatial structure of the disturbances. For those instances where they are -- such as in the case of elliptical flows where the instability mechanism is more subtle -- the results are not so favorable. The origins and extent of this modeling problem are examined in detail along with a possible resolution based on rapid distortion theory (RDT) and its implications for turbulence modeling.

Speziale, Charles G.↗
NASA NTRS1973

Laser Doppler velocity measurements of swirling flows with upstream influence

Swirling flow in a rotating tube is studied by flow visualization at a moderate Reynolds number, and its velocity field is measured by laser-Doppler anemometry. The tube has constant diameter, and approximately uniform initial rigid rotation of the flow is assured by passing the flow through a rotating plug of porous metal before it enters the test section. At moderate swirl values, an object mounted on the tube centerline causes a closed bubble to form upstream of the obstacle, with a clearly defined stagnation point on the axis, and recirculating flow inside the bubble. The bubble length grows upstream as the swirl is increased, until it breaks up into a Taylor column reaching all the way upstream and downstream at swirl values above a certain critical value. A vortex jump (in the sense of Benjamin) occurs downstream of the obstacle except when the Taylor column is present. Using a laser-Doppler anemometer, axial and swirl velocity profiles are obtained at several stations upstream and downstream of the bubble, and in and around the bubble.

Rloff, K. L.↗
NASA NTRS2012

The Evolution of Friction Stir Welding Theory at Marshall Space Flight Center

From 1995 to the present the friction stir welding (FSW) process has been under study at Marshall Space Flight Center (MSFC). This is an account of the progressive emergence of a set of conceptual tools beginning with the discovery of the shear surface, wiping metal transfer, and the invention of a kinematic model and making possible a treatment of both metallurgical structure formation and process dynamics in friction stir welding from a unified point of view. It is generally observed that the bulk of the deformation of weld metal around the FSW pin takes place in a very narrow, almost discontinuous zone with high deformation rates characteristic of metal cutting. By 1999 it was realized that this zone could be treated as a shear surface like that in simple metal cutting models. At the shear surface the seam is drawn out and compressed and pressure and flow conditions determine whether or not a sound weld is produced. The discovery of the shear surface was followed by the synthesis of a simple 3- flow kinematic model of the FSW process. Relative to the tool the flow components are: (1) an approaching translational flow at weld speed V, (2) a rotating cylindrical plug flow with the angular velocity of the tool , and (3) a relatively slow ring vortex flow (like a smoke ring) encircling the tool and driven by shoulder scrolls and pin threads. The rotating plug flow picks up an element of weld metal, rotates it around with the tool, and deposits it behind the tool ( wiping metal transfer ); it forms plan section loops in tracers cut through by the tool. Radially inward flow from the ring vortex component retains metal longer in the rotating plug and outward flow expels metal earlier; this interaction forms the looping weld seam trace and the tongue and groove bimetallic weld contour. The radial components of the translational and ring vortex flows introduce parent metal intrusions into the small grained nugget material close to the tool shoulder; if this feature is pronounced, nugget collapse may result. Certain weld features, in particular internal banding seen in transverse section as onion rings and associated surface ridges called tool marks , have long implied an oscillation flow component, but have only recently been attributed in the literature to tool eccentricity. Rotating plug shape, typically a hollow cylinder flared at the end where it sticks to the shoulder, varies as pressure distribution on the tool determines where sticking occurs. Simplified power input estimates balanced against heat loss estimates give reasonable temperature estimates, explain why the power requirement changes hardly at all over a wide range of RPM s, and yield isotherms that seem to fall along boundaries of parameter windows of operation.

Nunes, Arthur C.↗
NASA NTRS1990

Transitions from Hadley to Rossby flows in internally forced rotating spherical systems

The possibility of global-scale transitions between the Hadley and Rossby atmospheric regimes is investiated using a simple three-dimensional rotating spherical model without a boundary layer structure, bottom topography, or cumulus friction, and the expected occurrence of the Hadley to Rossby transition is demonstrated. It is shown that a transition from Hadley flow to wavenumber-5 Rossby flow is preferred, in agreement with standard baroclinic instability results. This result gives a reasonable Rossby wave bifurcation from the Hadley solution. For the cases examined, it was found that the upper symmetric Hadley regime does not exist and that the Hadley to Rossby transition depends on the values of the eddy viscosities.

Higgins, Wayne R.↗
NASA NTRS1986

Flow regimes in a shallow rotating cylindrical annulus with temperature gradients imposed on the horizontal boundaries

Experimental flow regime diagrams are determined for a new rotating cylindrical annulus configuration which permits a measure of control over the internal vertical temperature gradient. The new annulus has radial temperature gradients imposed on plane horizontal thermally conducting endwalls (with the cylindrical sidewalls as insulators) and is considered to be more relevant to atmospheric dynamics studies than the classical cylindrical annulus. Observations have revealed that, in addition to the axisymmetric flow and nonaxisymmetric baroclinic wave flow which occur in the classical annulus, two additional nonaxisymmetric flow types occur in the new annulus: boundary-layer thermal convection and deep thermal convection. Flow regime diagrams for three different values of the imposed vertical temperature difference are presented, and explanations for the flow transitions are offered. The new annulus provides scientific backup for the proposed Atmospheric General Circulation Experiment for Spacelab. The apparatus diagram is included.

Hathaway, D. H.↗
NASA NTRS1985

The application of potential flow theory to the rotational dynamics of spheroids, disks, and cylinders

An example for the considered phenomenon in the area of cloud microphysics is the rotational motion of ice particles as they fall through the air. Of fundamental importance for the general problem is a knowledge of the magnitude of the torque exerted by the fluid on the translating object as well as the frequency of the rotational oscillation which results from this torque. The present investigation has the objective to obtain estimates of these quantities, and to assess the accuracy of these estimates. Torques and oscillation frequencies for spheroidal objects immersed in flow are computed for potential flow and compared to measured values. The results form a consistent picture in which the ratios of measured to potential flow values are always less than 1 but generally greater than 0.1. The reason for this is described in terms of the well-known deviations of real flow from potential flow. The reported results are of academic interest in filling a gap in the knowledge regarding the applicability of potential flow.

Weinheimer, A. J.↗