Search NASA⌕ Search

SEARCH · Search NASA

Results for “shuttle effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Space-Shuttle Emulator Software

A package of software has been developed to execute a raw binary image of the space shuttle flight software for simulation of the computational effects of operation of space shuttle avionics. This software can be run on inexpensive computer workstations. Heretofore, it was necessary to use real flight computers to perform such tests and simulations. The package includes a program that emulates the space shuttle orbiter general- purpose computer [consisting of a central processing unit (CPU), input/output processor (IOP), master sequence controller, and buscontrol elements]; an emulator of the orbiter display electronics unit and models of the associated cathode-ray tubes, keyboards, and switch controls; computational models of the data-bus network; computational models of the multiplexer-demultiplexer components; an emulation of the pulse-code modulation master unit; an emulation of the payload data interleaver; a model of the master timing unit; a model of the mass memory unit; and a software component that ensures compatibility of telemetry and command services between the simulated space shuttle avionics and a mission control center. The software package is portable to several host platforms.

Arnold, Scott↗
NASA NTRS1973

Misalignment studies on space shuttle integrated vehicle (IA31FC)

The effects of test model element misalignments on test results were investigated. Transonic wind tunnel-573 was designed to study these misalignment effects in detail by purposely misaligning model elements a known amount. Misalignments in TWT-573 were achieved by use of special off-set spacers and mounting hardware to change, yaw, pitch and roll on various elements of a 0.004-Scale PRR Baseline space shuttle configuration model. By comparing the misalignment runs to the nominal configuration with no misalignment, relative effects of the misalignment could be seen. This data was obtained over a Mach range of .9 to 1.46 using an angle of attack sweep of minus 10 deg to plus 10 deg in 2 deg increments.

Ramsey, P.↗
NASA NTRS1974

Space shuttle launch vehicle (13 P-OTS) strut support interference effects study in the Rockwell International 7- by 7-foot trisonic wind tunnel (IA68)

Strut support interference investigations were conducted on an 0.004-(-) scale representation of the space shuttle launch vehicle in order to determine transonic and supersonic model support interference effects for use in a future exhaust plume effects study. Strut configurations were also tested. Orbiter, external tank, and solid rocket booster pressures were recorded at Mach numbers 0.9, 1.2, 1.5, and 2.0. Angle of attack and angle of sideslip were varied between plus or minus 4 degrees in 2 degree increments. Parametric variations consisted only of the strut configurations.

Rogge, R. L.↗
NASA NTRS1976

A low speed wind tunnel test of a 0.050 scale model of shuttle orbiter (model 089B) to investigate the longitudinal and lateral directional effects of canard and tail configurational modifications in the LTV LSWT (MA14)

A low speed wind tunnel test was conducted to determine the effects of 6 canard configurations on the 0.050 scale model of shuttle orbiter 089B. In addition, two horizontal tail configurations were tested at two positions on the model as were two wing configurations. Since this test was restricted to 103 runs, only a limited number of permutations of the configurational changes could be tested. The testing was done in the 15 by 20 foot section of the LSWT and consisted of pitch polars, one yawed polar and several yaw runs. The pitch polars encompassed an alpha range from 0 to 28 deg; the yawed polar was run at beta = +2 degrees and the yaw runs covered a beta range from -6 to +6 deg at angles-of-attack of 0, 4, 10, 16, and 20 deg.

Chambliss, E. B.↗
NASA NTRS1975

The effects of environmental exposure on reusable surface insulation for space shuttle

Coated specimens of reusable surface insulation (RSI) were exposed to alternate radiant heating and atmospheric exposure cycles to study the effects of surface contamination on the RSI coating. Different methods of heating were employed on clean and artificially contaminated specimens to determine the contributions of heating conditions to coating devitrification.

Ransone, P. O.↗
NASA NTRS1973

Silica RSI for Application to the Shuttle Orbiter

Silica reusable surface insulation is analyzed for its cold soak properties, bond properties at low temperature, gap and step heating effects, and aerodynamic surface roughness effects to determine space shuttle weight and cost sensitivity to structure subsystem weights. Computerized simulation studies show that total program cost savings of silica (vs. mullite) exceed thermal protection system design and development costs and that an early introduction of silica increases total program cost savings.

Forsberg, K. J.↗
NASA NTRS1987

Effects of forced and free convections on structural temperatures of Space Shuttle Orbiter during reentry flight

Structural performance and resizing (SPAR) finite-element thermal analysis computer program was used in the heat transfer analysis of the Space Shuttle Orbiter wing subjected to reentry aerodynamic heating. With sufficient external forced convective cooling near the end of the heating cycle, the calculated surface temperatures of the thermal protection system (TPS) agree favorably with the flight data for the entire flight profile. However, the effects of this external forced convective cooling on the structural temperatures were found to be negligible. Both free convection and forced convection elements were introduced to model the internal convection effect of the cool air entering the Shuttle interior. The introduction of the internal free convection effect decreased the calculated wing lower skin temperatures by 20 F at most, 1200 sec after touchdown. If the internal convection is treated as forced convection, the calculated wing lower skin temperatures after touchdown can be reduced to match the flight-measured data very closely. By reducing the TPS thicknesses to certain effective thickness to account for the TPs gap heating, the calculated wing lower skin temperatures prior to touchdown can be raised to agree with the flight data perfectly.

Ko, William L.↗
NASA NTRS1983

Catalytic surface effects on space thermal protection system during Earth entry of flights STS-2 through STS-5

An on going orbiter experiment catalytic surface effects experiment being conducted on the Space Shuttle is discussed. The catalytic surface effects experiment was peformed on four of the five flights of Columbia. Temperature time histories and distributions along the midfuselage and wing of the orbiter were used to determine the surface catalytic efficiency of the baseline high temperature reusable surface insulation. Correlation parameters are shown that allow the comparison of all flight data with predictions from the design and surface emittance decreased as a result of contaminants during the five flights of the Space Shuttle.

Stewart, D. A.↗
NASA NTRS1975

Data report for tests on the heat transfer effects of the 0.0175 scale Rockwell International Space Shuttle Vehicle model 22-OT in the AEDC 50 inch B wind tunnel (0H4B), volume 1

Results of wind tunnel heat transfer tests of 0.0175-scale Rockwell International Space Shuttle Vehicle configurations for orbiter alone, tank alone, and orbiter plus external tank are presented. Body flap shielding of SSME's during simulated entry was investigated. The tests were conducted at Mach 8 for thirteen Reynolds number.

Foster, T. F.↗
NASA NTRS1975

Data report for tests on the heat transfer effects of the 0.0175-scale Rockwell International Space Shuttle Vehicle model 22-OT in the AEDC 50-inch B wind tunnel (OH4B), volume 3

Results of wind tunnel heat transfer tests of 0.0175-scale Rockwell International Space Shuttle Vehicle configurations for orbiter alone, tank alone, and orbiter plus external tank are presented. Body flap shielding of SSME's during simulated entry was also investigated. The tests were conducted at Mach 8 for thirteen Reynolds number per foot values ranging from 0.5 million to 3.72 million.

Foster, T. F.↗
NASA NTRS1977

Space shuttle engineering and operations support: Study of the effects of multiple ground updates on the accuracy of the onboard state vector with IMU only navigation

There are six cases considered: (1) no updates made during the flight, (2) one ground update in the vertical components only at the first practice separation minus 15 minutes, (3) one ground update in all components at the first practice separation minus 5 minutes, (4) updates 2 and 3 applied successively, (5) Case 4 plus an update in all components at the second separation attempt minus 3 minutes, and (6) one ground update at first separation attempt minus 5 minutes and a second update at second separation minus two minutes. The mission control simulation program, GROPER, was run using as radar input a tape containing radar derived state vectors for the trajectory.

Killen, R.↗
NASA NTRS2005

Effect of Impact Location on the Response of Shuttle Wing Leading Edge Panel 9

The objective of this paper is to compare the results of several simulations performed to determine the worst-case location for a foam impact on the Space Shuttle wing leading edge. The simulations were performed using the commercial non-linear transient dynamic finite element code, LS-DYNA. These simulations represent the first in a series of parametric studies performed to support the selection of the worst-case impact scenario. Panel 9 was selected for this study to enable comparisons with previous simulations performed during the Columbia Accident Investigation. The projectile for this study is a 5.5-in cube of typical external tank foam weighing 0.23 lb. Seven locations spanning the panel surface were impacted with the foam cube. For each of these cases, the foam was traveling at 1000 ft/s directly aft, along the orbiter X-axis. Results compared from the parametric studies included strains, contact forces, and material energies for various simulations. The results show that the worst case impact location was on the top surface, near the apex.

Lyle, Karen H.↗
NASA NTRS1980

Risetime distortion of Shuttle Ku-band payload 50 MBPS data due to coaxial cable skin effects

This paper discusses distortion of digital signals generated in the Space Shuttle Ku-band communications systems. Specifically, the degradation considered is due to coaxial cables which interface data and clock from a source located in the payload bay to the KuSPA (Ku-Band Signal Processor Assembly) located in the avionics bay of the Shuttle. Due to the length (nearly 100 feet) and relatively narrow bandwidth of the cable, the clock and data waveforms are significantly affected by this transmission medium. This paper presents a closed form model that closely approximates the distortion of the waveforms measured in laboratory tests.

Schadelbauer, S.↗