SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
We report new B-band CCD surface photometry on a sample of 76 disk galaxies brighter than BT = 14.5 mag in the Uppsala General Catalogue of Galaxies, which are confined within a volume located in the outer part of the Local Supercluster.
A numerical solution of an elastohydrodynamic lubrication (EHL) contact between two long rough surface cylinders is obtained. A simultaneous solution of an elasticity equation and the Reynolds equation for two partially lubricated rough surfaces is used to obtain a theoretical solution of pressure distribution, elastohydrodynamic load and film thicknesses for given speeds. A theoretical solution is also found for lubricants with pressure dependent viscosity, material properties of cylinders, and surface roughness parameters. Elastic deformation is found from hydrodynamic and contact pressure using plane strain analysis, and results indicate that for a constant central film thickness, increasing the surface roughness decreases the EHL load and there is little variation in minimum film thicknesses as the surface roughness is increased.
The subject turbine was investigated to determine the effect of high rotor pressure-surface diffusion on turbine performance. A comparison of the subject turbine with the most efficient transonic turbine in the present series of investigations showed that the efficiency of the subject turbine was almost as high, the suction-surface diffusion parameter was about the same, and the solidity was reduced by 36 percent. Because the loss per blade increased greatly with an increase in pressure-surface diffusion, the latter is also considered to be an important design consideration.
Stratospheric aerosols play key roles in the chemistry and radiation balance of the atmosphere and are a key input parameter for global chemistry and climate models. The degree to which aerosols impact chemistry and radiation balance depends primarily on the relative abundance of different sized particles within the sample volume, often referred to as the particle size distribution (PSD). If the PSD is accurately known then other key modeling parameters (e.g., surface area density and effective radius) can be derived. Historically, occultation observations from orbital instruments such as SAGE III/ISS have been used to infer these PSD parameters by inverting the extinction coefficient spectra. However, past efforts routinely failed to account for measurement uncertainty and lacked a rigorous estimate of the inferred PSD uncertainty. We carried out a series of simulations to evaluate the accuracy of these inferences and, for every valid SAGE III/ISS extinction spectrum, determined the range of PSD parameters that fell withing the bounds of the extinction error bars. Special application of this method was applied to estimate the impact of the 2022 Hunga Tonga eruption had on particle size distributions.
Stratospheric aerosols play key roles in the chemistry and radiation balance of the atmosphere and are a key input parameter for global chemistry and climate models. The degree to which aerosols impact chemistry and radiation balance depends primarily on the relative abundance of different sized particles within the sample volume, often referred to as the particle size distribution (PSD). If the PSD is accurately known then other key modeling parameters (e.g., surface area density and effective radius) can be derived. Historically, occultation observations from orbital instruments such as SAGE III/ISS have been used to infer these PSD parameters by inverting the extinction coefficient spectra. However, past efforts routinely failed to account for measurement uncertainty and lacked a rigorous estimate of the inferred PSD uncertainty. We developed a PSD solution algorithm that infers single mode and bimodal distribution parameters and applied this algorithm to the SAGE II and SAGE III/ISS data record. Herein we describe the algorithm, evaluate its performance, and show results from the 2022 Hunga Tonga eruption.
An approach to the retrieval of a vector wind field from Doppler lidar observations is developed in general terms. The field of radial velocity measurements from each look angle is modeled by a smooth surface, the parameters of the model being determined from the data by least squares techniques. The vector wind field and higher order fields are obtained from the two modeled surfaces. Estimated measurement errors are taken into account, and error estimates are available for all output data sets.
A method is developed for calculating the surface load and radiated sound from a vibrating surface in a compressible viscous fluid. The method is applied to a thin two-dimensional elliptic cross-section. For large values of the viscous diffusion parameter, the surface load tends to an elliptic distribution in agreement with the results of inviscid theory when edge pressure continuity is enforced. For thin surfaces, the surface load is insensitive to variations in the thickness ratio. A three-dimensional spectral technique is developed to calculate the inviscid surface load and radiated sound from a thin vibrating airfoil. The inviscid theory predicts the correct form of the far field sound pressure and its phase. The actual levels are somewhat sensitive to the choice of theoretical spanwise surface pressure mode but are in better agreement with the experiment than the surface pressure. The comparison of theoretical and experimental surface pressure indicates that the viscous theory, used to validate the inviscid theory, is either inadequate or there is a source of experimental error.
An approach to the retrieval of a vector wind field from Doppler lidar observations is developed in general terms. The field of radial velocity measurements from each look angle is modeled by a smooth surface, the parameters of the model being determined from the data by least squares techniques. The vector wind field and higher-order fields are obtained from the two modeled surfaces. Estimated measurement errors are taken into account, and error estimates are available for all output data sets.
A generalization of the single soil layer variable infiltration capacity (VIC) land surface hydrological model previously implemented in the Geophysical Fluid Dynamics Laboratory (GFDL) general circulation model (GCM) is described. The new model is comprised of a two-layer characterization of the soil column, and uses an aerodynamic representation of the latent and sensible heat fluxes at the land surface. The infiltration algorithm for the upper layer is essentially the same as for the single layer VIC model, while the lower layer drainage formulation is of the form previously implemented in the Max-Planck-Institut GCM. The model partitions the area of interest (e.g., grid cell) into multiple land surface cover types; for each land cover type the fraction of roots in the upper and lower zone is specified. Evapotranspiration consists of three components: canopy evaporation, evaporation from bare soils, and transpiration, which is represented using a canopy and architectural resistance formulation. Once the latent heat flux has been computed, the surface energy balance is iterated to solve for the land surface temperature at each time step. The model was tested using long-term hydrologic and climatological data for Kings Creek, Kansas to estimate and validate the hydrological parameters, and surface flux data from three First International Satellite Land Surface Climatology Project Field Experiment (FIFE) intensive field campaigns in the summer-fall of 1987 to validate the surface energy fluxes.
The invention is a Weld Analysis and Control System developed for active weld system control through real time weld data acquisition. Closed-loop control is based on analysis of weld system parameters and weld geometry. The system is adapted for use with automated welding apparatus having a weld controller which is capable of active electronic control of all aspects of a welding operation. Enhanced graphics and data displays are provided for post-weld analysis. The system provides parameter acquisition, including seam location which is acquired for active torch cross-seam positioning. Torch stand-off is also monitored for control. Weld bead and parent surface geometrical parameters are acquired as an indication of weld quality. These parameters include mismatch, peaking, undercut, underfill, crown height, weld width, puddle diameter, and other measurable information about the weld puddle regions, such as puddle symmetry, etc. These parameters provide a basis for active control as well as post-weld quality analysis and verification. Weld system parameters, such as voltage, current and wire feed rate, are also monitored and archived for correlation with quality parameters.
New first- and second-order displacement transfer functions have been developed for deformed shape calculations of nonuniform cross-sectional beam structures such as aircraft wings. The displacement transfer functions are expressed explicitly in terms of beam geometrical parameters and surface strains (uniaxial bending strains) obtained at equally spaced strain stations along the surface of the beam structure. By inputting the measured or analytically calculated surface strains into the displacement transfer functions, one could calculate local slopes, deflections, and cross-sectional twist angles of the nonuniform beam structure for mapping the overall structural deformed shapes for visual display. The accuracy of deformed shape calculations by the first- and second-order displacement transfer functions are determined by comparing these values to the analytically predicted values obtained from finite element analyses. This comparison shows that the new displacement transfer functions could quite accurately calculate the deformed shapes of tapered cantilever tubular beams with different tapered angles. The accuracy of the present displacement transfer functions also are compared to those of the previously developed displacement transfer functions.
The study presents a model that incorporates the physics and physical chemistry of ice surfaces relevant to polar stratospheric clouds. Surface concentrations of H2O, HCl, HOCl, ClONO2, and N2O5 on ice and nitric acid trihydrate (NAT) crystals are computed, and surface reaction rates and reaction probabilities (sticking coefficients) are determined. For gas pressures of about 10 exp -7 torr and temperatures in the range of 180-200 K, HCl completely coats ice and water-rich NAT surfaces, while HOCl, ClOHO2, and N2O5 may cover 0.01-1 percent of these surfaces. The energy parameters are used to calculate surface temperatures such as adsorption and desorption constants, surface coverages, reaction rate coefficients, surface diffusion coefficients, and reaction probabilities for various species and chemical interactions on ice and NAT surfaces. Implications for chemical processing on polar stratospheric clouds are discussed.
Over nearly all of the surface of Venus the reflectivity and emissivity at centimeter wavelengths are about 0.15 and 0.85 respectively. These values are consistent with moderately dense soils and rock populations, but the mean reflectivity is about a factor of 2 greater than that for the Moon and other terrestrial planets. Pettingill and Ford, using Pioneer Venus reflectivities and emissivities, found a number of anomalous features on Venus that showed much higher reflectivities and much lower emissivities with both values approaching 0.5. These include Maxwell Montes, a number of high regions in Aphrodite Terra and Beta Regio, and several isolated mountain peaks. Most of the features are at altitudes above the mean radius by 2 to 3 km or more. However, such features have been found in the Magellan data at low altitudes and the anomalies do not exist on all high structures, Maat Mons being the most outstanding example. A number of papers have been written that attempt to explain the phenomena in terms of the geochemistry balance of weathering effects on likely surface minerals. The geochemists have shown that the fundamentally basaltic surface would be stable at the temperatures and pressures of the mean radius in the form of magnetite, but would evolve to pyrite and/or pyrrhotite in the presence of sulfur-bearing compounds such as SO2. Pyrite will be stable at altitudes above 4 or 5 km on Venus. Although the geochemical arguments are rather compelling, it is vitally important to rationally look at other explanations for radar and radio emission measurements such as that presented by Tryka and Muhleman. The radar reflectivity values are retrieved from the raw Magellan backscatter measurements by fitting the Hagfors' radar scattering model in which a surface roughness parameters and a normal incidence electrical reflectivity are estimated. The assumptions of the theory behind the model must be considered carefully before the results can be believed. These include that the surface roughness exists only at horizontal scales large compared to the wavelength, the vertical deviations are gaussianly distributed, there is no shadowing, and that the reflection occurs at the interface of two homogeneous dielectric half-spaces. Probably all these conditions are violated at the anomalous features under discussion. The most important of these is the homogeneity of the near surface of Venus, particularly in highlands. Under the assumptions of the theory, all of the radio energy is reflected by the impedance jump at the very boundary. However, in heterogeneous soil some fraction of the illuminating energy is propagated into the soil and then scattered back out by impedance discontinuities such as rock, voids, and cracks. In light soils, the latter effect can overwhelm the scattering effects of the true surface and greatly enhance the backscatter power, suggesting a much higher value of an effective dielectric constant that would be estimated from Hagfors' model.
τ Sco, a well-studied magnetic B-type star in the Upper Sco association, has a number of surprising characteristics. It rotates very slowly and shows nitrogen excess. Its surface magnetic field is much more complex than a purely dipolar configuration which is unusual for a magnetic massive star. We employ the CMFGEN radiative transfer code to determine the fundamental parameters and surface CNO and helium abundances. Then, we employ MESA and GENEC stellar evolution models accounting for the effects of surface magnetic fields. To reconcile τ Sco’s properties with single-star models, an increase is necessary in the efficiency of rotational mixing by a factor of 3–10 and in the efficiency of magnetic braking by a factor of 10. The spin-down could be explained by assuming a magnetic field decay scenario. However, the simultaneous chemical enrichment challenges the single-star scenario. Previous works indeed suggested a stellar merger origin for τ Sco. However, the merger scenario also faces similar challenges as our magnetic single-star models to explain τ Sco’s simultaneous slow rotation and nitrogen excess. In conclusion, the single-star channel seems less likely and versatile to explain these discrepancies, while the merger scenario and other potential binary-evolution channels still require further assessment as to whether they may self-consistently explain the observables of τ Sco.
τSco, a well-studied magnetic B-type star in the Upper Sco association, has a number of surprising characteristics. It rotates very slowly and shows nitrogen excess. Its surface magnetic field is much more complex than a purely dipolar configuration which is unusual for a magnetic massive star. We employ the CMFGEN radiative transfer code to determine the fundamental parameters and surface CNO and helium abundances. Then, we employ MESA and GENEC stellar evolution models accounting for the effects of surface magnetic fields. To reconcileτSco’s properties with single-star models, an increase is necessary in the efficiency of rotational mixing by a factor of 3–10 and in the efficiency of magnetic braking by a factor of 10. The spin-down could be explained by assuming a magnetic field decay scenario. However, the simultaneous chemical enrichment challenges the single-star scenario. Previous works indeed suggested a stellar merger origin forτSco. However, the merger scenario also faces similar challenges as our magnetic single-star models to explainτSco’s simultaneous slow rotation and nitrogen excess. In conclusion, the single-star channel seems less likely and versatile to explain these discrepancies, while the merger scenario and other potential binary-evolution channels still require further assessment as to whether they may self-consistently explain the observables of τSco.
The surface of the Moon is electrically charged by exposure to solar radiation on its dayside, as well as by the continuous flux of charged particles from the various plasma environments that surround it. An electric potential develops between the lunar surface and ambient plasma, which manifests itself in a near-surface plasma sheath with a scale height of order the Debye length. This study investigates surface charging on the lunar dayside and near-terminator regions in the solar wind, for which the dominant current sources are usually from the pohotoemission of electrons, J(sub p), and the collection of plasma electrons J(sub e) and ions J(sub i). These currents are dependent on the following six parameters: plasma concentration n(sub 0), electron temperature T(sub e), ion temperature T(sub i), bulk flow velocity V, photoemission current at normal incidence J(sub P0), and photo electron temperature T(sub p). Using a numerical model, derived from a set of eleven basic assumptions, the influence of these six parameters on surface charging - characterized by the equilibrium surface potential, Debye length, and surface electric field - is investigated as a function of solar zenith angle. Overall, T(sub e) is the most important parameter, especially near the terminator, while J(sub P0) and T(sub p) dominate over most of the dayside.
Discrete ordinate radiative transfer calculations are used to examine the relative influence of cloud layers on the received ultraviolet flux and the received solar energy for a plane parallel atmosphere. The wavelength dependence for the cloud influence on the integrated solar radiation is primarily a function of the interaction of the cloud layer with the surrounding atmosphere and the underlying surface. It is found that for uv wavelengths greater than 300 nm, the ratio of uv to solar energy flux transmission through the atmosphere is insensitive to changes of cloud height, cloud scattering parameters and surface albedo (for realistic values), but is dependent on cloud thickness. For wavelengths approaching and less than 300 nm, absorption by tropospheric ozone results in sensitivity to cloud height and surface albedo.
Streamlined erosional forms in the Channeled Scabland are compared with streamline features recognized in the region of the Kasei Vallis on Mars shown in Viking imagery. The morphometric analysis considers three physical parameters, length, measured parallel to the suggested flow direction; width, taken as the maximum width of the streamlined form perpendicular to the flow direction; and area, measured with a grid placed over the surface. These parameters are used to calculate a dimensionless parameter k, defined as the square of the length multiplied by pi over four times the area. For the 137 Scabland forms studied k values range from 1.0 to 8.3 with an average of 3.2. The k values for 47 Martian streamlined forms range from 1.5 to 12.0 with an average of 3.8. The rough similarity of these results suggests that the terrestrial and Martian features were formed by similar processes. The forms appear to have developed an ideal shape, sufficiently elongated to reduce pressure drag in the fluid creating them, but not so long as to create excessive skin resistance.