Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface scattering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Scattering properties of the Venusian surface - Preliminary results from Magellan

Extraction of the scattering function over incidence angles between 0 and 4-10 deg from Magellan altimetry radar data is discussed. The scattering model includes a surface which is statistically homogeneous and isotropic in its scattering behavior. The results indicate that the model is useful in a global context, but further improvements to the analysis procedure are required if the best results are to be obtained locally. The procedures used here are still under development and include several steps which have not been fully optimized but which are expected to be effective over a wide range of Venusian conditions.

Tyler, G. L.↗
NASA NTRS1995

Comparison of Retracking Algorithms Using Airborne Radar and Laser Altimeter Measurements of the Greenland Ice Sheet

This paper compares four continental ice sheet radar altimeter retracking algorithms using airborne radar and laser altimeter data taken over the Greenland ice sheet in 1991. The refurbished Advanced Application Flight Experiment (AAFE) airborne radar altimeter has a large range window and stores the entire return waveform during flight. Once the return waveforms are retracked, or post-processed to obtain the most accurate altitude measurement possible, they are compared with the high-precision Airborne Oceanographic Lidar (AOL) altimeter measurements. The AAFE waveforms show evidence of varying degrees of both surface and volume scattering from different regions of the Greenland ice sheet. The AOL laser altimeter, however, obtains a return only from the surface of the ice sheet. Retracking altimeter waveforms with a surface scattering model results in a good correlation with the laser measurements in the wet and dry-snow zones, but in the percolation region of the ice sheet, the deviation between the two data sets is large due to the effects of subsurface and volume scattering. The Martin et al model results in a lower bias than the surface scattering model, but still shows an increase in the noise level in the percolation zone. Using an Offset Center of Gravity algorithm to retrack altimeter waveforms results in measurements that are only slightly affected by subsurface and volume scattering and, despite a higher bias, this algorithm works well in all regions of the ice sheet. A cubic spline provides retracked altitudes that agree with AOL measurements over all regions of Greenland. This method is not sensitive to changes in the scattering mechanisms of the ice sheet and it has the lowest noise level and bias of all the retracking methods presented.

Ferraro, Ellen J.↗
NASA NTRS1989

Evidence of alloy formation during reduction of platinized tin oxide surfaces

Ion scattering spectroscopy, Auger electron spectroscopy, and electron spectroscopy for chemical analysis have been used to examine a platinized tin oxide catalyst surface before, during, and after reduction by annealing under vacuum at 250 to 450 C. These techniques were then used to examine the reduced surface after a room-temperature, low-pressure oxygen exposure. The spectral results and the behavior of the reduced surface toward oxygen exposure both indicate that a Pt/Sn alloy is produced during reduction.

Gardner, Steven D.↗
NASA NTRSDate not supplied

Mirror Surface Contamination Specification Derived from Coronagraphy Scatter Error Budget Allocation

Near-Angle Scatter (NAS) of the host star’s light may limit the ability of a potential Habitable Worlds Observatory (HWO) to detect and characterize an Earth-like planet around a Sun-like star via coronagraphy. NAS from each optical surface before the coronagraph’s focal plane mask produces an E-field across the dark hole that is coherent. These E-fields sum and could be as large or larger than the coronagraph mask leakage E-field. This paper assumes an error budget allocation for scatter of 20 ppt. NAS E-fields contribute to the dark hole noise floor via both shot noise and heterodyne amplification of the wavefront instability. While previous papers have developed specifications for scatter from surface scatter, this paper develops specifications for scatter from surface contamination and micrometeoroid impacts. The development process utilizes an expression that predicts scatter throughput into the dark hole based on surface BRDF. Analysis does not include scatter from coating columnar structure, edges, contamination, micrometeoroid impacts, or polarization.

near angle scatter↗
DOE OSTI2023

NETL Plastic Pipes Project (Final Report)

Plastic or composite pipelines have been the bane of the utility locating industry because they are neither conductive nor magnetic which are the properties traditionally used to locate buried utilities. Ground penetrating radar (GPR) is an effective geophysical tool for locating plastic/composite pipelines where resistive cover allows for adequate penetration of radar energy. However, GPR has limited applicability in areas where the soil cover is conductive due to significant clay and/or salt content. This study examines complementary near-surface geophysical methods that are potentially useful for locating buried plastic/composite pipelines, either singly or in combination. Specifically, this modeling study used computational numerical methods to forward model the response of GPR, resistivity, seismic, gravity gradiometry, and photoacoustic/thermoacoustic imaging methods to plastic/composite pipelines for various scenarios including: (1) pipe diameters ranging between 2 in. to 12 in.; (2) burial depths ranging between 3 ft. to 4 ft.; (3) various degrees in contrast in physical properties (i.e., electrical permittivity, elasticity, resistivity, density); and (4) various experimental acquisition choices (e.g., GPR radar and seismic source frequencies, electrode spacing). Numerical modeling performed herein reconfirmed that GPR is the preferred method for detecting/locating plastic pipelines. A caveat for GPR detection is that the material covering the plastic pipe (trench fill material and adjacent soil) must be sufficiently resistive to allow the two-way propagation to the required depth of investigation and back to the surface. GPR was the only method modeled in this study that can be used to directly detect plastic pipelines of 2-in.-diameter and larger when buried 3-ft-deep. GPR data processing and imaging also can determine pipe depth, pipe diameter, trench dimensions, and moisture conditions. Seismic modeling results suggest that direct detection of a 12-in.-diameter plastic pipe at 3-ft.-depth may be possible under favorable conditions; however, the associated signature would be weak (e.g., surface- to S-wave, backscattered surface-waves, and/or forward scattered surface-waves to S-wave). Direct pipe detection under field conditions with noise and strong lateral geologic heterogeneity is doubtful. Numerical modeling also suggests that plastic pipelines can be indirectly located by detecting the trench in which they are buried. GPR, direct current (DC) resistivity, and seismic methods have the potential to locate the pipeline trench if there is sufficient contrast between the trench-wall and trench-fill materials for the physical property being measured by each method (i.e., electrical permittivity for GPR; resistivity for DC resistivity; or density, compressional velocity, or shear velocity for seismic). Modeling also indicated that currently available (commercial) gravity gradiometers would be unable to directly detect/locate plastic pipelines ≤ 8-in.-diameter when buried 3-ft.-deep given the typical instrument noise floor for field surveying as well as the expected density variations due to geologic heterogeneity. The numerical modeling performed in this project did not identify a universal geophysical technology that can locate buried plastic pipelines in all parts of the United States (although GPR is suggested for all areas with resistive cover). However, the project results suggest that a towed land streamer simultaneously acquiring multiple geophysical data types including multi-offset GPR, multi-channel DC resistivity, seismic geophone- and/or distributed acoustic sensing (DAS), and potentially photoacoustic/thermoacoustic data would be an appropriate platform for locating buried plastic pipeline. Moreover, the complementary multiphysics data acquired by a towed land streamer would permit the use of joint and/or cooperative inversion frameworks for a more rigorous and consistent data interpretation.

42 ENGINEERING↗
NASA NTRS1992

Comparison of measurements and theory for backscatter from vegetation-covered soil on the Konza prairie

Radar backscatter measurements over the Konza Prairie were obtained by means of C- and X-band scatterometers as a part of the first ISLSCP Field Experiment (FIFE) to determine soil moisture. Nearly simultaneous radar and radiometer data sets were collected along two transects that coincided with direct soil-moisture measurements. The results show that radars can be used for soil-moisture estimation over the complete transect, whereas radiometer sensitivity to soil moisture is drastically reduced over regions left unburned for many years. A combined rough-surface/volume scatter model was formulated. Calculated and measured scattering data are compared to determine the sensitivity of the scattering coefficient to different surface treatments.

Gogineni, S.↗
NASA NTRS1978

Comparison of quasi-specular radar scatter from the moon with surface parameters obtained from images

Quasi-specular radar scatter from geologic surfaces displays a variable wavelength dependence in apparent surface roughness. Wavelength dependence will occur whenever a significant fraction of the surface has local radii of curvature comparable to the observing wavelength. This condition can be determined by comparison of the value of the integrated surface curvature spectrum with the radar wavenumber, multiplied by a constant that depends on the geometry. Variations in curvature statistics calculated from photogrammetric reduction of lunar images are consistent with the observed variations in quasi-specular scatter at the same locations. Variations in the strength of the wavelength dependence are correlated with the sizes of lunar craters that lie near the upper size limit for the local steady state distribution. This correlation is also consistent with variations in the curvature spectrum calculated from crater size-frequency distributions.

Tyler, G. L.↗
DOE OSTI2021

In situ microbeam surface X-ray scattering reveals alternating step kinetics during crystal growth

The stacking sequence of hexagonal close-packed and related crystals typically results in steps on vicinal {0001} surfaces that have alternating A and B structures with different growth kinetics. However, because it is difficult to experimentally identify which step has the A or B structure, it has not been possible to determine which has faster adatom attachment kinetics. Here we show that in situ microbeam surface X-ray scattering can determine whether A or B steps have faster kinetics under specific growth conditions. We demonstrate this for organo-metallic vapor phase epitaxy of (0001) GaN. X-ray measurements performed during growth find that the average width of terraces above A steps increases with growth rate, indicating that attachment rate constants are higher for A steps, in contrast to most predictions. Overall, our results have direct implications for understanding the atomic-scale mechanisms of GaN growth and can be applied to a wide variety of related crystals.

36 MATERIALS SCIENCE↗
NASA NTRS1982

Wave scattering from a periodic dielectric surface for a general angle of incidence

Electromagnetic waves scattered from a periodic dielectric and perfectly conducting surface are studied for a general angle of incidence. It is shown that the one-dimensional corrugated surface can be solved by using two scalar functions: the components of the electric and magnetic fields along the row direction of the surface, and appropriate boundary conditions to obtain simple matrix equations. Results are compared to the case where the incident angle wave vector is perpendicular to the row direction. Numerical results demonstrate that energy conservation and reciprocity are obeyed for scattering by sinusoidal surfaces for the general case, which checks the consistency of the formalism.

Chuang, S. L.↗
NASA NTRS2010

Surface-Enhanced X-Ray Fluorescence

Surface-enhanced x-ray fluorescence (SEn-XRF) spectroscopy is a form of surface- enhanced spectroscopy that was conceived as a means of obtaining greater sensitivity in x-ray fluorescence (XRF) spectroscopy. As such, SEn-XRF spectroscopy joins the ranks of such other, longer-wavelength surface-enhanced spectroscopies as those based on surface-enhanced Raman scattering (SERS), surface-enhanced resonance Raman scattering (SERRS), and surfaceenhanced infrared Raman absorption (SEIRA), which have been described in previous NASA Tech Briefs articles. XRF spectroscopy has been used in analytical chemistry for determining the elemental compositions of small samples. XRF spectroscopy is rapid and quantitative and has been applied to a variety of metal and mineralogical samples. The main drawback of XRF spectroscopy as practiced heretofore is that sensitivity has not been as high as required for some applications. In SEn-XRF as in the other surface-enhanced spectroscopies, one exploits several interacting near-field phenomena, occurring on nanotextured surfaces, that give rise to local concentrations of incident far-field illumination. In this case, the far-field illumination comes from an x-ray source. Depending on the chemical composition and the geometry of a given nanotextured surface, these phenomena could include the lightning-rod effect (concentration of electric fields at the sharpest points on needlelike surface features), surface plasmon resonances, and grazing incidence geometric effects. In the far field, the observable effect of these phenomena is an increase in the intensity of the spectrum of interest - in this case, the x-ray fluorescence spectrum of chemical elements of interest that may be present within a surface layer at distances no more than a few nanometers from the surface.

Anderson, Mark↗
NASA NTRS1985

Surface texture characterization by angular distributions of scattered light

Work at the National Bureau of Standards to develop an on-line optical measurement device and attendant algorithms for automated optical scattering measurements of machined metal surfaces are described. The surfaces could be milled, ground or lapped, and the system is intended to categorize the resulting surface characteristics. The optical device consists of a He-Ne laser which is shone on a surface. The scattered light is captured by a semicircular array of 87 detector elements rotated over the scanned area. The light signals are processed through a digital voltmeter and then an A/D converter. The signals are then stored for later comparisons with optical scattering data obtained by optical instruments used with stylus instruments for characterizing surface topographies. A theoretical model has been defined which relates light scattering and the characteristics of the surface roughness. Initial experimental results with a sinusoidal surface have indicated that although the system can follow the trend of the roughness, the roughness amplitude is as yet uncertainly defined and the computations require excessive time.

Gilsinn, D. E.↗
NASA NTRS1981

The albedo of snow for partially cloudy skies

The albedo of snow is defined as the ratio of reflected to incident solar energy, and it is an important parameter in the earth's radiation budget analysis and in the study of snowpack's thermal conditions. An approximate model for calculating the incident spectral flux for partially cloudy skies is presented. The input parameters for the calculation are atmospheric precipitable water, turbidity, ozone content, surface pressure, the optical thickness of clouds, and the grain size of snow crystals. The spectral snow reflectance model considers both specular surface reflection and volumetric multiple scattering. The surface reflection is calculated by using a crystal-shape-dependent bidirectional reflectance distribution function; the volumetric multiple scattering is calculated by using a crystal-size-dependent approximate solution in the radiative transfer equation. The model yields spectral and integrated solar flux and snow reflectance as a function of solar elevation and fractional cloud-cover. The illustrative insolation and albedo values were obtained from spectral reflectance and incident flux for representative parameters of Antarctic coastal regions. A simple relationship between grain size and the overcast albedo was obtained. For a set of grain size and shape, the albedo as a function of solar elevation and fractional cloud cover was tabulated.

Choudhury, B. J.↗
NASA NTRS1985

Influence of aerosol scattering on atmospheric blurring of surface features

The influence of the shape of atmospheric scattering phase functions on blurring of surface detail in images acquired from space is investigated. The effects are characterized by computing atmospheric transfer functions and by solving the multidimensional equation of radiative transfer using a Fourier transform method. It is predicted that increased forward scattering enhances the detectability of atmospheric blurring near reflectance boundaries. Results for off-nadir viewing are also presented.

Diner, D. J.↗
DOE OSTI2025

Particle removal from a flat surface using a translating bounded vortex flow

A bounded vortex flow is a hydrodynamic approach for removal of particles from a surface without scattering the particles onto nearby surfaces. The bounded vortex flow field is generated by a nozzle that combines azimuthally tilted jets arranged in a circular pattern and a central suction port. When the nozzle face is directed toward an ‘impingement surface’, the flow develops a wall-normal intake vortex below the suction outlet, which causes high shear stress on the impingement surface. When particles are present on the impingement surface, the high shear stress causes particles to roll along the surface and to be lifted off the surface and transported up the core of the wall-normal vortex into the suction outlet. In typical applications, the nozzle would be translated along the impingement surface to clean particles from the surface. The current paper reports on an experimental study of the effect of nozzle translation on the effectiveness of the bounded vortex flow field for particle mitigation. The effectiveness of particle mitigation was examined as a function of flow rate through the nozzle, particle size, and nozzle translation velocity relative to the impingement surface. As a result, numerical computations are used to relate the flow rate to the maximum shear stress on the impingement surface, which is then used to theoretically predict onset of particle motion.

42 ENGINEERING↗