Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface steps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Direct torsional actuation of microcantilevers using magnetic excitation

Torsional mode dynamic force microscopy can be used for a wide range of studies including mapping lateral contact stiffness, torsional frequency or amplitude modulation imaging, and dynamic friction measurements of various materials. Piezo-actuation of the cantilever is commonly used, but it introduces spurious resonances, limiting the frequency range that can be sampled, and rendering the technique particularly difficult to apply in liquid medium where the cantilever oscillations are significantly damped. Here, we demonstrate a method that enables direct torsional actuation of cantilevers with high uniformity over wide frequency ranges by attaching a micrometer-scale magnetic bead on the back side of the cantilever. We show that when beads are magnetized along the width of the cantilever, efficient torsional actuation of the cantilevers can be achieved using a magnetic field produced from a solenoid placed underneath the sample. We demonstrate the capability of this technique by imaging atomic steps on graphite surfaces in tapping mode near the first torsional resonance of the cantilever in dodecane. The technique is also applied to map the variations in the lateral contact stiffness on the surface of graphite and polydiacetylene monolayers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

cDPD: A new dissipative particle dynamics method for modeling electrokinetic phenomena at the mesoscale

In this work, we develop a “charged” dissipative particle dynamics (cDPD) model for simulating mesoscopic electrokinetic phenomena governed by the stochastic Poisson-Nernst-Planck and the Navier-Stokes equations. In particular, the transport equations of ionic species are incorporated into the DPD framework by introducing extra degrees of freedom and corresponding evolution equations associated with each DPD particle. Diffusion of ionic species driven by the ionic concentration gradient, electrostatic potential gradient, and thermal fluctuations is captured accurately via pairwise fluxes between DPD particles. The electrostatic potential is obtained by solving the Poisson equation on the moving DPD particles iteratively at each time step. For charged surfaces in bounded systems, an effective boundary treatment methodology is developed for imposing both the correct hydrodynamic and electrokinetics boundary conditions in cDPD simulations. To validate the proposed cDPD model and the corresponding boundary conditions, we first study the electrostatic structure in the vicinity of a charged solid surface, i.e., we perform cDPD simulations of the electrostatic double layer and show that our results are in good agreement with the well-known mean-field theoretical solutions. Furthermore, we simulate the electrostatic structure and capacity densities between charged parallel plates in salt solutions with different salt concentrations. Moreover, we employ the proposed methodology to study the electro-osmotic and electro-osmotic/pressure-driven flows in a micro-channel. In the latter case, we simulate the dilute poly-electrolyte solution drifting by electro-osmotic flow in a micro-channel, hence demonstrating the flexibility and capability of this method in studying complex fluids with electrostatic interactions at the micro- and nano-scales.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Polarization-induced 2D hole gases in pseudomorphic undoped GaN/AlN heterostructures on single-crystal AlN substrates

A high-conductivity two-dimensional (2D) hole gas is the enabler of wide-bandgap p-channel transistors. Compared to commonly used AlN template substrates with high dislocation densities, the recently available single-crystal AlN substrates are promising to boost the speed and power handling capability of p-channel transistors based on GaN/AlN 2D hole gases (2DHGs) thanks to the much lower dislocation densities and the absence of thermal boundary resistance. Using plasma-assisted molecular beam epitaxy, we report the observation of polarization-induced high-density 2DHGs in undoped pseudomorphic GaN/AlN heterostructures on the single-crystal AlN substrates with high structural quality and atomic steps on the surface. The high-density 2DHG persists down to cryogenic temperatures with a record high mobility exceeding 280 cm 2 /V s and a density of 2.2 × 10 13 /cm 2 at 10 K. These results shed light on aspects of improving 2D hole mobilities and indicate significant potential of GaN/AlN 2DHG grown on bulk AlN substrates for future high performance wide-bandgap p-channel transistors.

36 MATERIALS SCIENCE↗

Role of electric fields in the MHD evolution of the kink instability

Here, the discovery of electrostatic fields playing a crucial role in establishing plasma motion in the flux conversion and dynamo processes in reversed field pinches is revisited. In order to further elucidate the role of the electrostatic fields, a flux rope configuration susceptible to the kink instability is numerically studied with anMHDcode. Simulated nonlinear evolution of the kink instability is found to confirm the crucial role of the electrostatic fields. Anew insight is gained on the special function of the electrostatic fields: they lead the plasma towards the reconnection site at the mode resonant surface. Without this step the plasma column could not relax to its nonlinear state, since no other agent is present to perform this role. While the inductive field generated directly by the kink instability is the dominant flow driver, the electrostatic field is found to allow the motion in the vicinity of the reconnection region.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Designing Ta C Virtual Substrates for Vertical Al x Ga 1 − x N Power Electronics Devices

Power electronics are critical for a sustainable energy future, playing a key role in electrification and integration of renewable energy sources into the grid. Advances in ultrawide band gap materials are needed to handle higher powers in smaller form factors while reducing electrical and thermal losses. High Al content Al x Ga 1 − x N is theoretically capable of meeting these demands, but its impact in power electronics has been severely restricted by a lack of substrates that can satisfy conductivity, lattice matching, and/or thermal expansion requirements. We demonstrate that electrically conductive Ta C can be used as a virtual substrate for Al x Ga 1 − x N heteroepitaxy. Scaleably sputtered Ta C grown on Al 2 O 3 , followed by high-temperature face-to-face annealing, produces a thin film Ta C template with an effective hexagonal lattice constant matched to Al 0.70 Ga 0.30 N . Annealing of the Ta C promotes recrystallization, significantly improving crystallinity and reducing crystalline defects from as-deposited columnar grains to a step-and-terrace surface morphology, enabling the subsequent growth of high-quality Al 0.70 Ga 0.30 N by molecular beam epitaxy. X-ray diffraction and scanning transmission electron microscopy confirm that the Al x Ga 1 − x N layer is heteroepitaxially aligned, strain-free, and lattice-matched, transitioning abruptly from Ta C to Al x Ga 1 − x N without intermediate phases. These results demonstrate Ta C virtual substrates as electrically conductive, lattice-matched, and thermally compatible templates for vertical Al x Ga 1 − x N devices that can meet the growing power needs of a sustainable energy future. Published by the American Physical Society 2024

36 MATERIALS SCIENCE↗

Tailoring MgZnO/CdSeTe Interfaces for Photovoltaics

Mg x Zn 1-x O (MZO) shows great promise to replace CdS as a buffer layer in CdTe-based solar cells. It is more transparent, and the MZO bandgap and electron density can be tuned, thus providing flexibility in controlling the conduction band offsets and recombination rates between transparent conductive oxide/MZO and MZO/CdSeTe interfaces. Integrating this material into solar cell devices has been frustrated by the common observation of abnormal current-voltage curves. Simulations indicate that this anomalous behavior can be attributed to front interface barrier effects. Experiments demonstrate that this common MZO interface problem can be resolved experimentally by surface preparation, preheat steps, and removing oxygen during absorber deposition and CdCl 2 treatment. Oxygen during the cell fabrication process is likely to alter MZO properties and MZO/CdSeTe band alignment. After addressing these interface issues and modest optimization, devices with high short-circuit density of 29 mA/cm 2 and efficiency above 16% are demonstrated.

14 SOLAR ENERGY↗

Catalytic resonance of ammonia synthesis by simulated dynamic ruthenium crystal strain

Ammonia affords dense storage for renewable energy as a fungible liquid fuel, provided it can be efficiently synthesized from hydrogen and nitrogen. In this work, the catalysis of ammonia synthesis was computationally explored beyond the Sabatier limit by dynamically straining a ruthenium crystal (±4%) at the resonant frequencies (10 2 to 10 5+ Hz) of N 2 surface dissociation and hydrogenation. Density functional theory calculations at different strain conditions indicated that the energies of NH x surface intermediates and transition states scale linearly, allowing the description of ammonia synthesis at a continuum of strain conditions. A microkinetic model including multiple sites and surface diffusion between step and Ru(0001) terrace sites of varying ratios for nanoparticles of differing size revealed that dynamic strain yields catalytic ammonia synthesis conversion and turnover frequency comparable to industrial reactors (400°C, 200 atm) but at lower temperature (320°C) and an order of magnitude lower pressure (20 atm).

10 SYNTHETIC FUELS↗

Formation of active sites on transition metals through reaction-driven migration of surface atoms

Adopting low-index single-crystal surfaces as models for metal nanoparticle catalysts has been questioned by the experimental findings of adsorbate-induced formation of subnanometer clusters on several single-crystal surfaces. Here we used density functional theory calculations to elucidate the conditions that lead to cluster formation and show how adatom formation energies enable efficient screening of the conditions required for adsorbate-induced cluster formation. We studied a combination of eight face-centered cubic transition metals and 18 common surface intermediates and identified systems relevant to catalytic reactions, such as carbon monoxide (CO) oxidation and ammonia (NH 3 ) oxidation. We used kinetic Monte Carlo simulations to elucidate the CO-induced cluster formation process on a copper surface. Scanning tunneling microscopy of CO on a nickel (111) surface that contains steps and dislocations points to the structure sensitivity of this phenomenon. Metal-metal bond breaking that leads to the evolution of catalyst structures under realistic reaction conditions occurs much more broadly than previously thought.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Distortion compensation in interferometric testing of mirrors

We present a method to compensate for the imaging distortion encountered in interferometric testing of mirrors, which is introduced by interferometer optics as well as from geometric projection errors. Our method involves placing a mask, imprinted with a regular square grid, over the mirror and finding a transformation that relates the grid coordinates to coordinates in the base plane of the parent surface. This method can be used on finished mirrors since no fiducials have to be applied to the surfaces. A critical step in the process requires that the grid coordinates be projected onto the mirror base plane before the regression is performed. We apply the method successfully during a center-of-curvature null test of an F/2 off-axis paraboloid.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Impact of Zr Content on Radionuclide Release Rates in Metal Waste Forms

Reference alloy waste forms (RAW) underwent hybrid corrosion/immersion testing to parameterize the ANL analytical oxidative-dissolution model to enable the calculation of fractional release rates. The waste forms tested at SRNL were variations of the RAW-3 formulation that uses HT9 as the main alloy component, and are meant to enable evaluation of the impact of Zr:U ratio on the release rates of actinides and Tc-99. The test solutions were air saturated alkaline and acidic brines, representing potential repositories with those conditions. The testing approach consisted of 4 major steps; 1) bare surface corrosion measurements, 2) hybrid potentiostatic hold/exposure measurements, 3) measurement of radionuclide concentrations and relations to anodic current from potentiostatic holds, and 4) identification of corroding phases using SEM/EDS of electrodes.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Introduction to Superconducting RF Structures and the Effect of High Pressure Rinsing

This presentation begins by describing RF superconductivity and SRF accelerating structures. Then the use of superconducting RF structures in a number of accelerators around the world is reviewed; for example, the International Linear Collider (ILC) will use ~16,000 SRF cavities with ~2,000 cryomodules to get 500 GeV e⁺/e⁻ colliding energy. Field emission control was (and still is) a very important practical issue for SRF cavity development. It has been found that high-pressure ultrapure water rinsing as a final cleaning step after chemical surface treatment resulted in consistent performance of single- and multicell superconducting cavities.

43 PARTICLE ACCELERATORS↗

Atomic-Scale Surface Studies of Bulk Metallic Glasses. Final Report

Bulk metallic glasses (BMGs) are of both scientific and technological interest because the absence of periodic atomic arrangements provides them with unique physical, chemical, and mechanical properties. Their high strength, superior elasticity, and an ability to be easily formed into virtually unlimited shapes with feature sizes from centimeters to Angstroms by blow molding and thermoplastic forming makes them an attractive choice for more and more practical applications and products. Due to their complex internal structure, however, experiments that yield insight into their exact atomic arrangements have been scarce. As a result, glass physics is one of the last remaining unexplored fields of materials science despite the scientific and technological importance of glasses in our daily lives, and the question how to characterize and control matter away from equilibrium, as glasses are, was listed as one of five Grand Challenges in a recent DoE report. The main reason for the slow progress in glass physics is the lack of experimental tools that enable access to atomic-scale structural and behavioral information for disordered materials. Such atomic-scale knowledge is mandatory to establish structure-property relationships that ultimately could allow to custom-design alloys featuring specific desired characteristics. With no such relationships available, theory development in glass remains basic and the few that exist are often untested. The aim of this research was to enable progress in our understanding of BMGs by developing a new approach that will allow a meaningful application of local surface science methods to specially prepared BMG samples to obtain a wealth of quantitative information on their atomic arrangements. Key was the availability of specially prepared samples whose surfaces feature large atomically flat terraces despite being entirely amorphous, which we have produced from a Pt 57.5 Cu 14.7 Ni 5.3 P 22.5 alloy (‘Pt-BMG’) both under ambient conditions as well as in ultrahigh vacuum using a unique setup that has been specially developed within this grant. Our approach starts with the in-situ preparation of oxide crystals that are terminated by large terraces, from which exact mirror images out of BMG will be produced using thermoplastic forming (TPF); for the research within this grant, we have successfully used (001)-oriented SrTiO 3 single crystal surfaces as well as (100)-, (110)-, and (111)-oriented single crystals made from LaAlO 3 . Since the resulting BMG replicas display all features of the original crystal with sub-Angstrom fidelity, thereby mimicking the original crystal’s termination by atomically flat terraces without being crystalline themselves, they are ideally suited for further investigation. The following atomic-scale local studies were then carried within this proposal: (i) high-resolution surface imaging and local spectroscopy using scanning probe microscopy, which showed disordered atom-like features and revealed changes in the gradient of the local surface potential on a 1-2 nm length scale; (ii) characterization of atomic-scale plastic flow with affected volumes as low as 1000 atoms, which showed local hardness near or above the theoretically predicted maximum and, once plastic deformation was initiated, homogeneous flow of the atoms involved; (iii) characterization of surface relaxation processes and the onset of crystallization induced by annealing, which showed that upon heating over the material’s glass transition temperature, the surface rearranges and relaxes towards a more stable, denser packed glass, which increases on-terrace surface roughness, while surface tension smoothens step edges; and (iv) studies that investigate the dependence of the material’s mechanical properties and structure on processing parameters, revealing that relaxed glasses get denser, harder, and more elastic. In combination, this information allows to combine structural models with mechanical properties and preparation history, thereby facilitating the development of preparation-structure-property relationships for metallic glasses. With the availability of such information, bulk metallic glasses can be further optimized to be used in more and more applications in industry.

36 MATERIALS SCIENCE↗

Benchmark Study Matrix for Microreactor Geometries Relevant to Multiple Developers

A benchmark study was developed that include design, development, manufacturing, and performance measurement of agnostic reactor relevant geometries to support industry’s adoption of advanced manufacturing in a variety of structures. A matrix of five microreactor component geometries, specifically based on the recent feasibility study on a Marvel microreactor liner, was developed and the Pacific Northwest National Laboratory team initiated one material/process combination, namely 316H using laser powder directed energy deposition (DED). Although the benchmark starts initially with simplistic cubical and cylindrical forms, it builds up to a mock-up of a non-proprietary design that can demonstrate a variety of features potentially useful for presenting knowledge to specific designers of microreactors and for the matter also for other reactor type designers. The initial cubical and cylindrical forms are initial steps to obtain surface features and dimensional responses to the identified process parameters to be used in the non-proprietary design mockup.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Update on the R&D of vertical buffered electropolishing on Nb samples and SRF single cell cavities

Electropolishing (EP) has become a popular choice as the final step of the surface removal process during the fabrication of Nb superconducting radio frequency (SRF) cavities. One of the major reasons for the choice is that Nb SRF cavities treated by EP tend to have a better chance to reach an accelerating gradient of 30 MV/m or higher than those treated by buffered chemical polishing (BCP). This advantage of EP over BCP can at least be partially attributed to the smoother Nb surfaces that EP can produce. Recently a Nb surface removal technique called buffered electropolishing (BEP) was developed at JLab. The root mean square of the Nb surfaces treated by BEP can be as smooth as 20nm over a surface area of 200X200 ?m2. In this contribution, R&D efforts of vertical BEP on Nb small flat samples and SRF single cell cavities since the last SRF conference in 2009 will be updated. It is shown that under a suitable condition, BEP can have a Nb removal rate as high as 10 ?m/mim that is more than 25 and 5 times quicker than those of EP and BCP(112) respectively. Possible mechanisms responsible for the high Nb removal rate are proposed. Clues on the optimization of vertical BEP and EP treatments on Nb SRF cavities from recent experimental results obtained on a Nb single cell demountable cavity will be discussed.

Wu, Andy↗

Ultra-thin microporous/hybrid materials

Ultra-thin hybrid and/or microporous materials and methods for their fabrication are provided. In one embodiment, the exemplary hybrid membranes can be formed including successive surface activation and reaction steps on a porous support that is patterned or non-patterned. The surface activation can be performed using remote plasma exposure to locally activate the exterior surfaces of porous support. Organic/inorganic hybrid precursors such as organometallic silane precursors can be condensed on the locally activated exterior surfaces, whereby ALD reactions can then take place between the condensed hybrid precursors and a reactant. Various embodiments can also include an intermittent replacement of ALD precursors during the membrane formation so as to enhance the hybrid molecular network of the membranes.

36 MATERIALS SCIENCE↗

Continuity conditions for tensor product Q-Bézier surfaces of degree (m, n)

Based on a kind of Q-Bézier surfaces with shape parameters, the basic properties of the surfaces and the geometric significance of the shape parameters are analyzed. To resolve the problem of shape control and adjustment of composite surfaces, the continuity conditions for Q-Bézier surfaces of degree (m, n) are investigated. Taking advantage of the terminal properties of generalized Bernstein basis functions, we derive the conditions of G{sup 1} and G{sup 2} continuity between two adjacent Q-Bézier surfaces. In addition, the specific steps of smooth continuity between Q-Bézier surfaces and the shape adjustment function of shape parameters for composite surfaces are discussed. The modeling examples show that the proposed smooth continuity conditions are not only intuitive and easy to implement, but also greatly enhance the shape adjustability, which provide a useful method for constructing complex surfaces in engineering design.

97 MATHEMATICS AND COMPUTING↗

Effect of Temperature on the Desorption of Lithium from Molybdenum(110) Surfaces: Implications for Fusion Reactor First Wall Materials

Determining the strength of Li binding to Mo is critical to assessing the survivability of Li as a potential first wall material in fusion reactors. Here, we present the results of a joint experimental and theoretical investigation into how Li desorbs from Mo(110) surfaces, based on what can be deduced from temperature-programmed desorption measurements and density functional theory (DFT). Li desorption peaks measured at temperatures ranging from 711 K (1 monolayer, ML) to 1030 K (0.04 ML), with corresponding desorption onsets from 489 to 878 K, follow a trend similar to predicted Gibbs free energies for Li adsorption. Bader charge analysis of DFT densities reveals that repulsive forces between neighboring positively charged Li atoms increase with coverage and thus reduce the bond strength between Mo and Li, thereby lowering the desorption temperature as the coverage increases. In addition, DFT predicts that Li desorbs at higher temperatures from a surface with vacancies than from a perfect surface, offering an explanation for the anomalously high desorption temperatures for the last Li to desorb from Mo(110). Analysis of simulated local densities of states indicates that the stronger binding to the defective surface is correlated with enhanced interaction between Li and Mo, involving the Li 2s electrons and not only the Mo 4d electrons as in the case of the pristine surface, but also the Mo 5s electrons in the case with surface vacancies. We suggest that steps and kinks present on the Mo(110) surface behave similarly and contribute to the high desorption temperatures. These findings imply that roughened Mo surfaces may strengthen Li film adhesion at higher temperatures.

36 MATERIALS SCIENCE↗

LaCrO3 heteroepitaxy on SrTiO3(001) by molecular beam epitaxy

Stoichiometric, epitaxial LaCrO3 films have been grown on TiO2-terminated SrTiO3(001) substrates by molecular beam epitaxy using O2 as the oxidant. Film growth occurred in a layer-by-layer fashion, giving rise to structurally excellent films and surfaces which preserve the step-terrace structure of the substrate. The critical thickness is in excess of 500 Å. Near-surface Cr(III) is highly susceptible to further oxidation to Cr(V), leading to the formation of a disordered phase upon exposure to atomic oxygen. Recovery of the original epitaxial LaCrO3 phase is readily achieved by vacuum annealing.

36 MATERIALS SCIENCE↗